负电子亲和势GaN光电阴极光谱响应特性研究

针对负电子亲和势（NEA） GaN光电阴极成功激活后的量子效率问题,利用自行研制的紫外光谱响应测试仪器,测试了成功激活的NEA GaN光电阴极的光谱响应,给出了230—400 nm波段内反射模式NEA GaN光电阴极的量子效率曲线.测试结果表明：反射模式下NEA GaN光电阴极在230nm具有高达37.4%的量子效率,在GaN光电阴极阈值365 nm处仍有3.75%的量子效率,230 nm和400 nm之间的抑制比率超过2个数量级.文中还结合国外的研究结果,综合分析了影响量子效率的因素. 关键词： 负电子亲和势 GaN光电阴极 光谱响应 反射模式     

反射式NEA GaN光电阴极量子效率恢复研究

以反射式NEA GaN光电阴极充分激活、衰减以及补Cs后的量子效率曲线为依据,针对阴极量子效率的衰减规律和补Cs后的恢复状况,论述了NEA GaN光电阴极量子效率的衰减和恢复机理.经过重新Cs化处理,反射式NEA GaN光电阴极量子效率在240 nm到300 nm的短波区域恢复到激活后最好状态的94%以上,300 nm到375 nm的长波区域恢复到88%以上.结合反射式NEA GaN光电阴极衰减前后的表面势垒形状和反射式GaN光电阴极量子效率的计算公式,得到了量子效率曲线的衰减规律以及补Cs后的恢复状况与 关键词： 反射式 NEA GaN光电阴极 量子效率     

反射式负电子亲和势GaN光电阴极量子效率衰减机理研究

针对反射式负电子亲和势(NEA) GaN光电阴极量子效率的衰减以及不同波段对应量子效率衰减速度的不同,参照国外给出的NEA GaN光电阴极在反射模式下量子效率曲线随时间的衰减变化情况,利用GaN光电阴极铯氧激活后的表面模型［GaN(Mg):Cs］:O-Cs,结合量子效率衰减过程中表面势垒的变化,研究了反射式NEA GaN光电阴极量子效率的衰减机理. 有效偶极子数量的减小是造成量子效率降低的根本原因,表面I,II势垒形状的变化造成了不同波段对应的量子效率下降速度的不同. 关键词： 负电子亲和势 GaN光电阴极 量子效率 表面势垒     

梯度掺杂与均匀掺杂GaN光电阴极的对比研究

为了提高负电子亲和势(NEA)GaN光电阴极的量子效率,利用金属有机化合物化学气相淀积(MOCVD)外延生长了梯度掺杂反射式GaN光电阴极,其掺杂浓度由体内到表面依次为1×10¹⁸ cm^-3,4×10¹⁷ cm^-3,2×10¹⁷ cm^-3和6×10¹⁶ cm^-3,每个掺杂浓度区域的厚度约为45 nm,总的厚度为180 nm.在超高真 关键词： NEA GaN光电阴极 梯度掺杂 量子效率 能带结构     

反射式负电子亲和势GaN光电阴极量子效率衰减机理研究

针对反射式负电子亲和势(NEA) GaN光电阴极量子效率的衰减以及不同波段对应量子效率衰减速度的不同,参照国外给出的NEA GaN光电阴极在反射模式下量子效率曲线随时间的衰减变化情况,利用GaN光电阴极铯氧激活后的表面模型［GaN(Mg):Cs］:O-Cs,结合量子效率衰减过程中表面势垒的变化,研究了反射式NEA GaN光电阴极量子效率的衰减机理. 有效偶极子数量的减小是造成量子效率降低的根本原因,表面I,II势垒形状的变化造成了不同波段对应的量子效率下降速度的不同.     

GaN真空面电子源光电发射机理研究

采用Cs源持续、O源断续的交替方法成功激活了GaN光电阴极,原位测试了透射模式下的光谱响应曲线,获得了透射模式下高达13%的量子效率.从一维定态薛定谔方程入手,得到了GaN真空面电子源材料的电子透射系数的表达式.对于一定形状的阴极表面势垒,电子透射系数决定于入射电子能量、表面势垒的高度和宽度.根据具有负电子亲和势(NEA)特性的透射式GaN光电阴极的能带及Cs,O覆盖过程中阴极表面势垒的变化情况,结合双偶极层[CaN(Mg):Cs]:O-Cs表面模型,分析了GaN真空面电子源材料NEA特性的形成原因.研究表明:Cs,O激活过程中形成的双偶极层对电子逸出起促进作用,双偶极层的形成是材料表面真空能级下降的原因. 关键词： GaN 电子源 透射系数 双偶极层     

NEA GaN光电阴极量子产额研究

围绕NEA GaN光电阴极光电发射过程的光谱响应理论,研究了其量子产额问题。分别给出了反射模式和透射模式NEA GaN光电阴极的量子产额计算公式,分析了影响量子产额的因素。分析了国外制备的反射模式和透射模式NEA GaN光电阴极的量子产额曲线。结果表明,目前制备的NEA GaN光电阴极已具有高达30%的量子效率和良好的发射性能。相同条件下,反射模式比透射模式的量子效率要高,而且反射模式不像透射模式那样存在短波限制。     

近紫外波段NEA GaN阴极响应特性的研究

为了深入理解近紫外波段NEA GaN阴极的光谱响应特性, 在超高真空系统中对MOCVD生长的不同发射层厚度和掺杂浓度的三个样品进行激活实验, 并在线测试样品光谱响应. 利用反射式GaN阴极量子效率公式和最小二乘法对入射光波长为0.25—0.35 μ之间的 阴极响应量子效率实验数据进行拟合, 分别得到后界面复合速率和拟合直线L的斜率, 并使用量子效率公式对入射光波长为0.35 μ时的反射式GaN阴极光谱响应量子效率进行仿真. 结果表明, 后界面复合速率和直线v的斜率都能很好地反映GaN阴极的响应性能, 当GaN阴极后界面复合速率小于10⁵ cm/s, 发射层的厚度取0.174—0.212 μ时, 阴极光谱响应性能最好. 关键词： 反射式GaN 势垒 最小二乘法 后界面缺陷     

负电子亲和势GaN光电阴极激活机理研究

利用自行研制的光电阴极激活评估实验系统,给出了GaN光电阴极Cs激活及Cs/O激活的光电流曲线.针对GaN光电阴极的负电子亲和势（NEA）特性的成因,结合激活过程中光电流变化规律和成功激活后的阴极表面模型,研究了NEA GaN光电阴极激活机理.实验表明：GaN光电阴极在单独导入Cs激活时就可获得明显的NEA特性,Cs/O激活时引入O后光电流的增长幅度不大.用双偶极层模型［GaN（Mg）：Cs］：O—Cs较好地解释了激活成功后GaN光电阴极NEA特性的成因. 关键词： 负电子亲和势 GaN 激活 光电流     

负电子亲和势GaN光电阴极的研究进展

GaN材料由于其优良的性能,成为紫外探测和真空电子源领域极具发展潜力的材料之一;目前制备的反射式GaN光电阴极的量子效率已达到70%以上,透射式也达到了30%.本文对GaN光电阴极的结构设计、表面清洗和Cs/O激活三大方面进行了综述,分析了影响量子效率的关键因素,并对今后可能的发展方向进行了展望. 关键词： GaN光电阴极 负电子亲和势 量子效率 进展     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.     

Direction-of-arrival estimation using matrix spatial prefiltering approach

An approach to direction-of-arrival （DOA） estimation for multiple narrowband farfield signals is proposed. The technique uses a novel matrix spatial prefiltering approach. Specifically, a matrix filter is designed to spatially filter the incoming data snapshots. The un-wanted components arriving from the stopband angular sectors are attenuated and the desired components from the angular sector of interest pass with minimal distortion. The matrix filter spatially filters the element-space data and the output reserves the element-space data property, which makes it very useful by passing sensor data through a spatial prefilter prior to applying many other array processors to attenuate interferences and improve system performance. Several examples of DOA estimation problem are presented to illustrate the performance of the proposed spatial prefiltering approach. Results of simulation and real data show that the pre-filter can efficiently attenuate the spatial interferences and significantly improve the estimation and resolution capability of DOA estimators at low signal-to-noise ratios for the sources located inside the passband sector. In addition, the use of spatial prefilter makes it possible to estimate DOAs for multiple sources more than the number of the elements of an array.     

Quantum efficiency calibration of opto-electronic detector by means of correlated photons method

A new calibration method of detectors can be realized by using correlated photons generated in spontaneous parametric down-conversion (SPDC) effect of nonlinear crystal.An absolute calibration system of detector quantum efficiency is performed.And its principle and experimental setup are introduced.A continuouswave (CW) ultraviolet (351 nm),diode-pumped,frequency-doubled,and solid-state laser is used to pump BBO crystal.The quantum efficiencies of the photomultiplier at 633,702,and 789 nm are measured respectively.The coincidence peaks are observed using coincidence circuit.Some measurement factors including the filter bandwidth of trigger channel,the detector position alignment and polarization of the pump light are analyzed.The uncertainties of this calibration method are also analyzed,and the relative uncertainties of total calibration are less than 5.8%.The accuracy of this method could be improved in the future.