Polymerization of butadiene with the NiCl2‐methylaluminoxane catalyst

The polymerization of butadiene (Bd) with the soluble and insoluble parts of the NiCl₂‐methylaluminoxane (MAO) catalyst was investigated. Both parts initiate the polymerization of Bd to give a high molecular weight polymer consisting of mainly cis‐1,4‐structure. The activity of the soluble part for the polymerization is higher than that of the insoluble part. We presume that NiCl₂ reacts with MAO to give a soluble alkyl‐nickel complex that shows high activity for the polymerization of Bd.     

Anionic polymerization of N,N‐dialkyl‐2‐methylenebut‐3‐enamide: Effect of alkyl substituents on polymerization behavior

Anionic polymerizations of three 1,3‐butadiene derivatives containing different N,N‐dialkyl amide functions, N,N‐diisopropylamide (DiPA), piperidineamide (PiA), and cis‐2,6‐dimethylpiperidineamide (DMPA) were performed under various conditions, and their polymerization behavior was compared with that of N,N‐diethylamide analogue (DEA), which was previously reported. When polymerization of DiPA was performed at ?78 °C with potassium counter ion, only trace amounts of oligomers were formed, whereas polymers with a narrow molecular weight distribution were obtained in moderate yield when DiPA was polymerized at 0 °C in the presence of LiCl. Decrease in molecular weight and broadening of molecular weight distribution were observed when polymerization was performed at a higher temperature of 20 °C, presumably because of the effect of ceiling temperature. In the case of DMPA, no polymer was formed at 0 °C and polymers with relatively broad molecular weight distributions (M_w/M_n = 1.2) were obtained at 20 °C. The polymerization rate of PiA was much faster than that of the other monomers, and poly(PiA) was obtained in high yield even at ?78 °C in 24 h. The microstructure of the resulting polymers were exclusively 1,4‐ for poly(DMPA), whereas 20–30% of the 1,2‐structure was contained in poly(DiPA) and poly(PiA). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3714–3721, 2010     

Effect of an alkyl substituted in salen ligands on 1,4‐Cis selectivity and molecular weight control in the polymerization of 1,3‐butadiene with (salen)Co(II) complexes in combination with methylaluminoxane

The effect of an alkyl substituted in the aromatic ring of the salen ligand on the polymerization of butadiene (Bd) with (salen)Co(II) complexes in combination with methylaluminoxane (MAO) was investigated. The activity for the polymerization of Bd was influenced significantly by the introduction of alkyl groups at the 3,3′,5,5′‐positions in the aromatic ring of the salen ligand, and both the polymerization rate and 1,4‐cis contents increased in the following order with respect to the alkyl group: H < CH₃ < t‐C₄H₉. This is in good agreement with the bulkiness of the alkyl groups. The activity for the polymerization of the (salen)Co(II) complex possessing t‐C₄H₉ at the 3,3′‐positions was higher than that of the (salen)Co(II) bearing t‐C₄H₉ at the 5,5′‐positions. Thus, the introduction of bulky substituents at the 3,3′‐positions of the salen ligand was an important factor in achieving both high activity and high 1,4‐cis selectivity in the polymerization of Bd with (salen)Co(II) complexes in combination with MAO. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4088–4094, 2006     

Copolymerization of styrene and butadiene with Ni(acac)2-methylaluminoxane catalyst

Copolymerization of styrene (St) and butadiene (Bd) with nickel(II) acetylacetonate [Ni(acac)₂]-methylaluminoxane (MAO) catalyst was investigated. Among the metal acetylacetonates [Mt(acac)_x] examined, Ni(acac)₂ showed a high activity for the copolymerization of St and Bd giving copolymers having high cis-1,4-microstructure in Bd units in the copolymer. The effect of alkylaluminum as a cocatalyst on the copolymerization of St and Bd with the Ni(acac)₂-MAO catalyst was observed, and MAO was found to be the most effective cocatalyst for the copolymerization. The monomer reactivity ratios for the copolymerization of St and Bd with the Ni(acac)₂-MAO catalyst were determined to be r_St = 0.07 and r_Bd = 3.6. Based on the obtained results, it was presumed that the random copolymers with high cis-1,4-microstructure in Bd units could be synthesized with the Ni(acac)₂-MAO catalyst without formation of each homopolymer. The polymerization mechanism with the Ni(acac)₂-MAO catalyst was also discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3838–3844, 1999     

Novel neodymium (III) isopropoxide‐methylaluminoxane catalyst for isoprene polymerization

A novel catalyst composed of neodymium (III) isopropoxide [Nd(OiPr)₃] and methylaluminoxane (MAO) was examined in isoprene polymerization. The Nd(OiPr)₃‐MAO catalyst proved to be highly effective in heptane even at low [Al]/[Nd] ratios (ca. 30) to give polyisoprene that possessed high cis‐1,4 stereoregularity (> ca. 90%), a high number‐average molecular weight (M_n ～10⁵), and relatively narrow molecular weight distributions (M_w/M_n = 1.9–2.8). The catalyst activity increased with an increasing [Al]/[Nd] ratio from 10 to 80 as well as temperature of aging and polymerization from 0 to 60 °C. The polymerization proceeded in the first order with respect to the monomer concentration. Aliphatic solvents (heptane and cyclohexane) achieved a higher yield and M_n of polymer than toluene as a solvent. The M_w/M_n ratio remained around 2.0, and the gel permeation chromatographic curve was always unimodal, indicating that this system is homogeneous and involves a single active site. The microstructure of polyisoprene was determined by IR, ¹H NMR, and ¹³C NMR. The cis‐1,4 contents of the final polymers stayed in the range of 90–92%, regardless of reaction conditions, indicating the high stability of stereospecificity of the catalyst. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1838–1844, 2002     

Polymerization of (E)‐1,3‐Pentadiene and (E)‐2‐methyl‐1,3‐pentadiene with neodymium catalysts: Examination of the factors that affect the stereoselectivity

(E)‐1,3‐Pentadiene (EP) and (E)‐2‐methyl‐1,3‐pentadiene (2MP) were polymerized to cis‐1,4 polymers with homogeneous and heterogeneous neodymium catalysts to examine the influence of the physical state of the catalyst on the polymerization stereoselectivity. Data on the polymerization of (E)‐1,3‐hexadiene (EH) are also reported. EP and EH gave cis‐1,4 isotactic polymers both with the homogeneous and with the heterogeneous system, whereas 2MP gave an isotactic cis‐1,4 polymer with the heterogeneous catalyst and a syndiotactic cis‐1,4 polymer, never reported earlier, with the homogeneous one. For comparison, the results obtained with the soluble CpTiCl₃‐based catalyst (Cp = cyclopentadienyl), which gives cis‐1,4 isotactic poly(2MP), are examined. A tentative interpretation is given for the mechanism of the formation of the stereoregular polymers obtained and a complete NMR characterization of the cis‐1,4‐syndiotactic poly(2MP) is reported. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3227–3232     

Polymerization of 2‐pentene with Ni(II) α‐diimine complex/M‐MAO catalyst and structure of the polymer

Polymerization of 2‐pentene with [ArN?C(An)C(An)·NAr)NiBr₂ (Ar?2,6‐iPr₂C₆H₃)] ( 1‐Ni) /M‐MAO catalyst was investigated. A reactivity between trans‐2‐pentene and cis‐2‐pentene on the polymerization was quite different, and trans‐2‐pentene polymerized with 1‐Ni /M‐MAO catalyst to give a high molecular weight polymer. On the other hand, the polymerization of cis‐2‐butene with 1‐Ni /M‐MAO catalyst did not give any polymeric products. In the polymerization of mixture of trans‐ and cis‐2‐pentene with 1‐Ni /M‐MAO catalyst, the M_n of the polymer increased with an increase of the polymer yields. However, the relationship between polymer yield and the M_n of the polymer did not give a strict straight line, and the M_w/M_n also increased with increasing polymer yield. This suggests that side reactions were induced during the polymerization. The structures of the polymer obtained from the polymerization of 2‐ pentene with 1‐Ni /M‐MAO catalyst consists of ? CH₂? CH₂? CH(CH₂CH₃)? , ? CH₂? CH₂? CH₂? CH(CH₃)? , ? CH₂? CH(CH₂CH₂CH₃)? , and methylene sequence ? (CH₂)_n? (n ≥ 5) units, which is related to the chain walking mechanism. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2858–2863, 2008     

Polymerization of β‐pinene with Schiff‐base nickel complexes catalyst: Synthesis of relatively high molecular weight poly(β‐pinene) at high temperature with high productivity

A series of easily accessible and stable Schiff‐base nickel complexes (complex 1 – 4 ) in conjunction with methylaluminoxane (MAO) were employed for the synthesis of relatively high molecular weight β‐pinene polymers at high temperature with high productivity. The ligand structure of the complex had a substantial effect on the polymerization in terms of the productivity and the molecular weight. With complex 4 in the presence of MAO, high molecular weight polymers of β‐pinene (M_n ～ 10,900) were obtained at 40 °C with an extremely high productivity up to 1.25 × 10⁷ g polyβ‐pinene/mol of Ni. ¹H NMR analyses showed that the obtained β‐pinene polymer was structurally identical to that formed by conventional cationic Lewis acid initiators. The polymerization was presumably initiated by the nickel cation formed by the reaction of the schiff‐base nickel complex and MAO, while the propagation proceeded in a manner typical for a conventional carbocationic polymerization process. Direct evidence for the carbocationic polymerization was offered by the fact that quenching of the polymerization with methanol at a low monomer conversion resulted in incorporation of a methoxyl end group into the polymer chain. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3739–3746, 2007     

Anionic polymerization of 4‐phenyl‐1‐buten‐3‐yne derivatives bearing electron‐withdrawing groups

The anionic polymerization of derivatives of 4‐phenyl‐1‐buten‐3‐yne was carried out to investigate the effect of substituents on the polymerization behavior. The polymerization of 4‐(4‐fluorophenyl)‐1‐buten‐3‐yne and 4‐(2‐fluorophenyl)‐1‐buten‐3‐yne in tetrahydrofuran at −78 °C with n‐BuLi/sparteine as an initiator gave polymers consisting of 1,2‐ and 1,4‐polymerized units in quantitative yields with ratios of 80/20 and 88/12, respectively. The molecular weights of the polymers were controlled by the ratio of the monomers to n‐BuLi, and the distribution was relatively narrow (weight‐average molecular weight/number‐average molecular weight < 1.2), supporting the living nature of the polymerization. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1016–1023, 2001     

Synthesis of thermo‐responsive poly(N‐vinylcaprolactam)‐containing block copolymers by cobalt‐mediated radical polymerization

Thermo‐responsive block copolymers based on poly(N‐vinylcaprolactam) (PNVCL) have been prepared by cobalt‐mediated radical polymerization (CMRP) for the first time. The homopolymerization of NVCL was controlled by bis(acetylacetonato)cobalt(II) and a molecular weight as high as 46,000 g/mol could be reached with a low polydispersity. The polymerization of NVCL was also initiated from a poly(vinyl acetate)‐Co(acac)₂ (PVAc‐Co(acac)₂) macroinitiator to yield well‐defined PVAc‐b‐PNVCL block copolymers with a low polydispersity (M_w/M_n = 1.1) up to high molecular weights (M_n = 87,000 g/mol), which constitutes a significant improvement over other techniques. The amphiphilic PVAc‐b‐PNVCL copolymers were hydrolyzed into unprecedented double hydrophilic poly(vinyl alcohol)‐b‐PNVCL (PVOH‐b‐PNVCL) copolymers and their temperature‐dependent solution behavior was studied by turbidimetry and dynamic light scattering. Finally, the so‐called cobalt‐mediated radical coupling (CMRC) reaction was implemented to PVAc‐b‐PNVCL‐Co(acac)₂ precursors to yield novel PVAc‐b‐PNVCL‐b‐PVAc symmetrical triblock copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation of macrodiols and polyols by chopping high‐molecular‐weight aliphatic polycarbonates

High‐molecular‐weight poly(1,4‐butylene carbonate) (PBC) (M_n: 40,000?90,000) was prepared through the condensation polymerization of dimethyl carbonate (DMC) and 1,4‐butanediol (BD) in the presence of 0.05 mol % sodium alkoxide catalyst. The subsequent feeding of 15 mol % HOAOH, such as 1,6‐hexanediol, 1,5‐pentanediol, 1,4‐cyclohexanedimethanol, or 1,4‐benzenedimethanol and stirring at 190–150 °C converted the extremely thick high‐molecular‐weight polymer to low‐molecular‐weight macrodiols with GPC‐measured M_n ～2000. The analysis of the ¹H NMR spectra indicated that the –A– units and 1,4‐butylene units were randomly distributed in the resulting oligomers. The chopping of the high‐molecular‐weight PBC using either triols or tetraols such as glycerol propoxylate, 1,1,1‐tris(hydroxymethyl)ethane, or pentaerythritol also afforded macropolyols containing branched chains with GPC‐measured M_n ～2000. When the chopped polymers were genuine PBCs, the resulting macrodiols or polyols were in a waxy state at room temperature. However, permanently oily compounds were obtained when the chopped polymers were prepared using 0.90 mole fraction of BD admixed with various other diols. The macrodiols and polyols synthesized in this study may have potential applications in the polyurethane industry. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1570–1580     

Living cationic polymerization of α‐methyl vinyl ethers using SnCl4

Cationic polymerization of α‐methyl vinyl ethers was examined using an IBEA‐Et_1.5AlCl_1.5/SnCl₄ initiating system in toluene in the presence of ethyl acetate at 0 ～ ?78 °C. 2‐Ethylhexyl 2‐propenyl ether (EHPE) had a higher reactivity, compared to corresponding vinyl ethers. But the resulting polymers had low molecular weights at 0 or ?50 °C. In contrast, the polymerization of EHPE at ?78 °C almost quantitatively proceeded, and the number‐average molecular weight (M_n) of the obtained polymers increased in direct proportion to the EHPE conversion with quite narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.05). In monomer‐addition experiments, the M_n of the polymers shifted higher with low polydispersity as the polymerization proceeded, indicative of living polymerization. In the polymerization of methyl 2‐propenyl ether (MPE), the living‐like propagation also occurred under the reaction conditions similar to those for EHPE, but the elimination of the pendant methoxy groups was observed. The introduction of a more stable terminal group, quenched with sodium diethyl malonate, suppressed this decomposition, and the living polymerization proceeded. The glass transition temperature of the obtained poly(MPE) was 34 °C, which is much higher than that of the corresponding poly(vinyl ether). This poly(MPE) had solubility characteristics that differed from those of poly(vinyl ethers). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2202–2211, 2008     

ATRP of MMA under 60Co γ‐irradiation at room temperature

In this work, atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was successfully carried out at room temperature (25 °C) under ⁶⁰Co γ‐irradiation environment. The polymerization proceeded smoothly with high conversion (>90%) within 7 h. The polymerizations kept the features of controlled radical polymerization: first‐order kinetics, well‐predetermined number‐average molecular weights (M_n,GPC), and narrow molecular weight distributions (M_w/M_n < 1.25). ¹H NMR spectroscope and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry confirmed that poly(methyl methacrylate) (PMMA) chain was end‐capped by the initiator moieties. The Cu(II) concentration could reduce to 20 ppm level while keeping good control over molecular weights. This is the first successful example for the ATRP of MMA under ⁶⁰Co γ‐irradiation at room temperature. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of metal‐free poly(1,4‐dioxan‐2‐one) by enzyme‐catalyzed ring‐opening polymerization

To avoid the harmful effects of metallic residues in poly(1,4‐dioxan‐2‐one) (PPDO) for medical applications, the enzymatic polymerization of 1,4‐dioxan‐2‐one (PDO) was carried out at 60 °C for 15 h with 5 wt % immobilized lipase CA. The lipase CA, derived from Candida antarctica, exhibited especially high catalytic activity. The highest weight‐average molecular weight (M_w = 41,000) was obtained. The PDO polymerization by the lipase CA occurred because of effective enzyme catalysis. The water component appeared to act not only as a substrate of the initiation process but also as a chain cleavage agent. A slight amount of water enhanced the polymerization, but excess water depressed the polymerization. PPDO prepared by enzyme‐catalyzed polymerization is a metal‐free polyester useful for medical applications. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1560–1567, 2000     

Designed organo‐layered silicates as nanoreactors for 1,3‐butadiene stereospecific polymerization toward rubber nanocomposites synthesis

Organo‐modified layered silicates were synthesized and used as inorganic carriers for CoCl₂(P^tBu₂Me)₂‐MAO catalyst in the polymerization of 1,3‐butadiene, yielding cis‐1,4‐enriched polybutadiene. The organoclays were prepared by: (i) intercalation of (ar‐vinyl‐benzyl)trimethyl ammonium chloride salt through an ion exchange reaction, and (ii) the edge‐surface grafting by trimethylchlorosilane. The ammonium modifier acts as “spacer” increasing the layer d‐spacing and as “filler” favoring the silylation of the edge‐surface clay hydroxyls. The grafted silane prevents the MAO cocatalyst from reacting with the edge‐OHs, by forcing it to react within the interlayer clay region. MAO lead to methylation of the cobalt complex and carbanion abstraction to give a cobalt‐methyl cation that is stabilized by the MAO anion. The nanoconfined cationic alkylated species insert the butadiene on the Co‐Me bond affording the growth of the polymer chains within the clay layers. The growing of the macromolecular chains fills the interlayer silicate region giving an intercalated polybutadiene rubber nanocomposite. The role of the silicate organo modification on the heterogeneous catalyst structural features, the polymerization behavior and the nanocomposite structures are discussed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Dependence of the luminescent properties and chain length of poly[2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐1,4‐phenylene vinylene] on the formation of cis‐vinylene bonds during Gilch polymerization

The presence of cis‐vinylene bonds in Gilch‐polymerized poly[2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐1,4‐phenylene vinylene] is reported. Through fractionation, species with a weight‐average molecular weight of less than 37,000 exhibited an abnormal blueshift of photoluminescence spectra in toluene solutions, and this was attributed to the presence of cis‐vinylene bonds, as verified by NMR spectroscopy. Surprisingly, the fractionated species (～1 wt %) with a weight‐average molecular weight of 5000 were mostly linked by the cis‐vinylene bonds. The concentration decreased with the molecular weight until a molecular weight of 37,000 was reached; at that point, the polymer chains contained mainly trans‐vinylene bonds. Obviously, the formation of cis‐vinylene bonds strongly inhibited the growth of polymer chains during Gilch polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2520–2526, 2005     

Manganese‐based transition metal complexes as new catalysts for olefin polymerizations

Three manganese complexes, Mn(acac)₃ (acac = acetylacetonate), Cp₂Mn (Cp = cyclopentadienyl), and Mn(salen)Cl [salen = 1,2‐cyclohexanediamino‐N,N′‐bis(3,5‐dit‐butyl‐salicylidene)], were used for ethylene and propylene polymerizations. These complexes, in combination with an alkylaluminum cocatalyst such as methylaluminoxane (MAO) or diethyl aluminum chloride (AlEt₂Cl), could promote ethylene polymerizations that yielded extremely high molecular weight linear polymers, but were inactive for propylene polymerizations. The counterparts supported on MgCl₂ showed activities even for propylene polymerizations and had remarkably enhanced activities for ethylene polymerizations. In the presence of an electron donor such as ethylbenzoate, the MgCl₂‐supported manganese‐based catalysts yielded a highly isotactic polypropylene with a high molecular weight. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3733–3738, 2001     

Cationic addition polymerization of 1,4‐dioxene using gacl3 as lewis acid catalyst: Long‐lived species‐mediated polymerization

Effective cationic addition polymerization of 1,4‐dioxene, a six‐membered cyclic olefin with two oxygen atoms adjacent to the double bond, was performed using a simple metal halide catalyst system in dichloromethane. The polymerization was controlled when the reaction was conducted using GaCl₃ in conjunction with an isobutyl vinyl ether–HCl adduct as a cationogen at –78°C to give polymers with predetermined molecular weights and relatively narrow molecular weight distributions. The long‐lived properties of the propagating species were further confirmed by a monomer addition experiment and the analyses of the product polymers by ¹H NMR and MALDI–TOF–MS. Although highly clean propagation proceeded, the apparent rate constant changed during the controlled cationic polymerization of 1,4‐dioxene. The reason for the change was discussed based on polymerization results under various conditions. The obtained poly(1,4‐dioxene) exhibited a very high glass transition temperature (T_g) of 217°C and unique solubility. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of a new 2‐amino‐glycan,poly‐(1→6)‐α‐D‐mannosamine,by ring‐opening polymerization of 1,6‐anhydro‐mannosamine derivatives

A stereoregular 2‐amino‐glycan composed of a mannosamine residue was prepared by ring‐opening polymerization of anhydro sugars. Two different monomers, 1,6‐anhydro‐2‐azido‐mannose derivative ( 3 ) and 1,6‐anhydro‐2‐(N, N‐dibenzylamino)‐mannose derivative ( 6 ), were synthesized and polymerized. Although 3 gave merely oligomers, 6 was promptly polymerized into high polymers of the number‐average molecular weight (M_n) of 2.3 × 10⁴ to 2.9 × 10⁴ with 1,6‐α stereoregularity. The differences of polymerizability of 3 and 6 from those of the corresponding glucose homologs were discussed. It was found that an N‐benzyl group is exceedingly suitable for protecting an amino group in the polymerization of anhydro sugars of a mannosamine type. The simultaneous removal of O‐ and N‐benzyl groups of the resulting polymers was achieved by using sodium in liquid ammonia to produce the first 2‐amino‐glycan, poly‐(1→6)‐α‐D ‐mannosamine, having high molecular weight through ring‐opening polymerization of anhydro sugars.© 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and properties of blue light‐emitting,silicon‐containing,regio‐ and stereoregular conjugated polymers

This article concerns the hydrosilylation polyaddition of 1,4‐bis(dimethylsilyl)benzene ( 1 ) with 4,4′‐diethynylbiphenyl, 2,7‐diethynylfluorene ( 2b ), and 2,6‐diethynylnaphthalene with RhI(PPh₃)₃ catalyst. Trans‐rich polymers with weight‐average molecular weights (M_w's) ranging from 19,000 to 25,000 were obtained by polyaddition in o‐Cl₂C₆H₄ at 150–180 °C, whereas cis‐rich polymers with M_w's from 4300 to 34,000 were obtained in toluene at 0 °C–r.t. These polymers emitted blue light in 4–81% quantum yields. The cis polymers isomerized into trans polymers upon UV irradiation, whereas the trans polymers did not. The device having a layer of polymer trans‐ 3b obtained from 1 and 2b demonstrated electroluminescence without any dopant. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2774–2783, 2004