A study on melt grafting of maleic anhydride onto low‐density polyethylene and its blend with polyamide 6

Graft copolymerization of low‐density polyethylene (LDPE) with a maleic anhydride (MAH) was performed using intermeshing corotating twin‐screw extruder in the presence of benzoyl peroxide (BPO). The LDPE/polyamide 6 (PA6) and LDPE‐g‐MAH/PA6 blends were prepared in a corotating twin‐screw extruder. The melt viscosity of the grafted LDPE was measured by a capillary rheometer. The grafted copolymer was characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microcopy (SEM). The influence of the variation in temperature, BPO and MAH concentration, and temperature on the grafting degree and on the melt viscosity was studied. The grafting degree increased appreciably up to about 0.45 phr and then decreased continuously with an increasing BPO concentration. According to the FTIR analysis, it was found that the amount of grafted MAH on the LDPE chains was ～5.1%. Thermal analysis showed that melting temperature of the graft copolymers decreases with increasing grafting degree. In addition to this, loss modulus (E″) of the copolymers first increased little with increasing grafting and then obviously decreased with increasing grafting degree. Furthermore, the results revealed that the tensile strength of the blends increased linearly with increasing PA6 content. The results of SEM and mechanical test showed that the blends have good interfacial adhesion and good stability of the phase structure, which is reflected in the mechanical properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 267–275, 2010     

Chemical and morphological evolution of PA‐6/Epm/Epm‐g‐MA blends in a twin screw extruder

Chemical conversion and morphological evolution of PA‐6/EPM/EPM‐g‐MA blends along a twin screw extruder were monitored by quickly collecting small samples from the melt at specific barrel locations. The results show that the MA content of all blends decreases drastically in the first zone of the extruder, i.e., upon melting of the blend components. Significant changes in morphology are also observed at this stage. A correlation between chemistry and morphology could thus be established. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1311–1320, 1999     

Polyamide‐6/natural clay mineral nanocomposites prepared by solid‐state shear milling using pan‐mill equipment

The polyamide‐6 (PA6)/natural clay mineral nanocomposites were successfully prepared by solid‐state shear milling method without any treatment of clay mineral and additives. PA6/clay mixture was pan‐milled to produce PA6/clay compounding powder, using pan‐mill equipment. The obtained powder as master batch was diluted with neat PA6 to prepare composites by a twin‐screw extruder. The clay silicate layers were found to be partially exfoliated and dispersed homogeneously at nanometer level in PA6 matrix. The rheological measurements and mechanical properties of nanocomposites were characterized. The shear viscosities of nanocomposites were higher than that of pure PA6, and tensile strength and tensile modulus increased, but Izod impact strength decreased, with increasing concentration of clay. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 249–255, 2006     

Water‐assisted melt compounding of nylon‐6/pristine montmorillonite nanocomposites

An exploratory pioneering study on the fabrication of nylon‐6/montmorillonite (MMT) nanocomposites with the aid of water as an intercalating/exfoliating agent via melt compounding in a twin‐screw extruder was conducted. Commercial nylon‐6 pellets and pristine MMT powder were directly fed into the hopper of the extruder. Water was then injected into the extruder downstream. After interactions with the nylon‐6 melt/pristine MMT system, water was removed from the extruder further downstream via a venting gate. As such, no third‐component residual was left within the extrudates. Transmission electron microscopy micrographs showed that pristine MMT was uniformly dispersed in the nylon‐6 matrix. The contact time between water and the nylon‐6/pristine MMT system inside the extruder was so short that nylon‐6 was subjected to very little hydrolysis, if any. The resultant nanocomposites showed higher stiffness, superior tensile strength, and improved thermal stability in comparison with their counterparts obtained without water assistance and the nylon‐6/organic MMT nanocomposites. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1100–1112, 2005     

Morphology of PC/SAN blends: effect of reactive compatibilization,SAN concentration,processing, and viscosity ratio

This article examines the effects of dispersed phase concentration, processing apparatus, viscosity ratio, and interfacial compatibilization using an SAN–amine compatibilizer on the morphology of blends of bisphenol A–polycarbonate (PC) with styrene–acrylonitrile (SAN) copolymers. For uncompatibilized blends, the dispersed phase particle size increased significantly with SAN concentration, and was found to exhibit a minimum at a viscosity ratio of approximately 0.35 for a fixed concentration of 30% SAN in the blend. Although the morphology of uncompatibilized PC/SAN blends mixed in a Brabender mixer, single‐ and twin‐screw extruders were quite similar, the twin‐screw extruder produced significantly finer morphologies in blends containing SAN–amine. The average particle size for blends compatibilized with the SAN–amine polymer was approximately half that of uncompatibilized blends and was relatively independent of viscosity ratio and dispersed phase composition. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 71–82, 1999     

Effects of melt‐processing conditions on the quality of poly(ethylene terephthalate) montmorillonite clay nanocomposites

Organically modified montmorillonite was synthesized with a novel 1,2‐dimethyl‐3‐N‐alkyl imidazolium salt or a typical quaternary ammonium salt as a control. Poly(ethylene terephthalate) montmorillonite clay nanocomposites were compounded via melt‐blending in a corotating mini twin‐screw extruder operating at 285 °C. The nanocomposites were characterized with thermal analysis, X‐ray diffraction, and transmission electron microscopy to determine the extent of intercalation and/or exfoliation present in the system. Nanocomposites produced with N,N‐dimethyl‐N,N‐dioctadecylammonium treated montmorillonite (DMDODA‐MMT), which has a decomposition temperature of 250 °C, were black, brittle, and tarlike resulting from DMDODA degradation under the processing conditions. Nanocomposites compounded with 1,2‐dimethyl‐3‐N‐hexadecyl imidazolium treated MMT, which has a decomposition temperature of 350 °C, showed high levels of dispersion and delamination. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2661–2666, 2002     

Effect of a silicate filler on the crystal morphology of poly(trimethylene terephthalate)/clay nanocomposites

A series of intercalated poly(trimethylene terephthalate) (PTT)/clay nanocomposites were prepared in a twin‐screw extruder by the melt mixing of PTT with either quaternary or ternary ammonium salt‐modified clays. The morphology and structure, along with the crystallization and melting behavior, and the dynamic mechanical behavior of the composites were characterized by X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and dynamic mechanical thermal analysis. The results showed that the PTT chains could undergo center‐mass transport from the polymer melt into the silicate galleries successfully during the blending and extrusion process. More coherent stacking of the silicate layers was reserved at higher clay concentrations and shorter blend times. Compared with conventionally compounded composites, the nanoscale‐dispersed organophilic clays were more effective as crystal nucleation agents. The influence of the nanosilicates on the crystallization and melting behavior of PTT became distinct when the concentration of clay was around 3 wt %. The changes in the crystallization behavior of the polymer/clay nanocomposites depended not only on the size of the silicates but also on the intrinsic crystallization characteristics of the polymers. The resulting nanocomposites showed an increase in the dynamic modulus of PTT and a decrease in the relaxation intensity (both in loss modulus and loss tangent magnitude). © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2275–2289, 2003     

Melt rheology of polylactide/montmorillonite nanocomposites

In this article, the linear and nonlinear shear rheological behaviors of polylactide (PLA)/clay (organophilic‐montmorillonite) nanocomposites (PLACNs) were investigated by an Advanced Rheology Expanded System rheometer. The nanocomposites were prepared by master batch method using a twin‐screw extruder with poly(ε‐caprolactone) (PCL) as a compatibilizer. The presence of org‐MMT leads to obvious pseudo‐solid‐like behaviors of nanocomposite melts. The behaviors caused by the formation of a “percolating network” derived from the reciprocity among the strong related sheet particles. Therefore, the storage moduli, loss moduli, and dynamic viscosities of PLACNs show a monotonic increase with MMT content. Nonterminal behaviors exists in PLACNs nanocomposites. Besides the PLACNs melts show a greater shear thinning tendency than pure PLA melt because of the preferential orientation of the MMT layers. Therefore, PLACNs have higher moduli but better processibility compared with pure PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3189–3196, 2007     

Extruder‐made TPO nanocomposites. I. Effect of maleated polypropylene and organoclay ratio on the morphology and mechanical properties

PP/PP‐g‐MA/MMT/EOR blend nanocomposites were prepared in a twin‐screw extruder at fixed 30 wt % elastomer and 0 to 7 wt % MMT content. Elastomer particle size and shape in the presence of MMT were evaluated at various PP‐g‐MA/organoclay masterbatch ratios of 0, 0.5, 1.0, and 1.5. The organoclay dispersion facilitated by maleated polypropylene serves to reduce the size of the elastomer dispersed phase particles and facilitates toughening of these blend nanocomposites. The rheological data analysis using modified Carreau‐Yasuda model showed maximum yield stress in extruder‐made nanocomposites compared with nanocomposites of reactor‐made TPO. Increasing either MMT content or the PP‐g‐MA/organoclay ratio can drive the elastomer particle size below the critical particle size below which toughness is dramatically increased. The ductile‐brittle transition shift toward lower MMT content as the PP‐g‐MA/organoclay ratio is increased. The D‐B transition temperature also decreased with increased MMT content and masterbatch ratio. Elastomer particle sizes below ～1.0 μm did not lead to further decrease in the D‐B transition temperature. The tensile modulus, yield strength, and elongation at yield improved with increasing MMT content and masterbatch ratio while elongation at break was reduced. The modified Mori‐Tanaka model showed better fit to experimental modulus when the effect of MMT and elastomer are considered individually. Overall, extruder‐made nanocomposites showed balanced properties of PP/PP‐g‐MA/MMT/EOR blend nanocomposites compared with nanocomposites of reactor‐made TPO. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Reactive blending of PE‐GMA/PA6 effect of composition and processing conditions

Blends of ethylene‐glycidyl methacrylate copolymer (PE‐GMA) and polyamide 6 (PA6) were prepared in a corotating twin screw extruder. Two processing temperatures were used in order to disperse PA6 in two forms: at high temperature in the molten state in molted PE‐GMA Matrix (emulsion type mixture) and at lower temperature as fillers in molted PEGMA matrix (suspension type mixture). Processed blends were analyzed by scanning electron microscopy and dynamic mechanical experiments to probe the reactivity in the extruder and the compatibilization phenomena. The dependence of the morphology and the rheological properties of PE‐GMA/PA6 blends on blend composition and screw rotational speed was also investigated and is discussed in the paper. The results show that dispersion of the two polymers in the molten state leads to a higher level of interfacial reaction. They also show that whatever the screw rotational speed and the temperature of extrusion are, the rate of interfacial reaction in PE‐GMA/PA6 blends is higher for 50/50 PE‐GMA/PA blends than for 70/30 PE‐GMA/PA blends. Copyright © 2015 John Wiley & Sons, Ltd.     

Oxygen‐barrier properties of cold‐crystallized and melt‐crystallized poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

This study examined the oxygen‐transport properties of poly(ethylene terephthalate‐co‐bibenzoate) (PETBB55) crystallized from the melt (melt crystallization) or quenched to glass and subsequently isothermally crystallized by heating above the glass‐transition temperature (cold crystallization). The gauche–trans conformation of the glycol linkage was determined by infrared analysis, and the crystalline morphology was examined by atomic force microscopy. Oxygen solubility decreased linearly with volume fraction crystallinity. For melt‐crystallized PETBB55, extrapolation to zero solubility corresponded to an impermeable crystal with 100% trans glycol conformations, a density of 1.396 g cm^?3, and a heat of melting of 83 J g^?1. From the melt, PETBB55 crystallized as space‐filling spherulites with loosely organized lamellae and pronounced secondary crystallization. The morphological observations provided a structural model for permeability consisting of impermeable platelets randomly dispersed in a permeable matrix. In contrast, cold‐crystallized PETBB55 retained the granular texture of the quenched polymer despite the high level of crystallinity, as measured by the density and heat of melting. Oxygen solubility decreased linearly with volume fraction crystallinity, but zero solubility corresponded to an impermeable defective crystal with a trans fraction of 0.83 and a density of 1.381 g cm^?3. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2489–2503, 2002     

Preparation and characterization of vinyltriethoxysilane grafted ethylene propylene diene terpolymer/linear low density polyethylene (EPDM‐g‐VTES/LLDPE) blends

Graft polymerization of vinyltriethoxysilane (VTES) onto ethylene‐propylene‐diene terpolymer (EPDM) was carried out in toluene using dicumylperoxide (DCP) as initiator. Effects of various parameters (EPDM content, VTES content, reaction time, reaction temperature and initiator concentration) on the grafting efficiency of VTES onto EPDM were investigated. At the optimum grafting efficiency conditions, EPDM‐g‐VTES was developed by melt mixing in a twin screw extruder and then linear (l), statically vulcanized (s) and dynamically vulcanized (d) blends of EPDM‐g‐VTES with linear low‐density polyethylene (LLDPE) with varying percentage compositions were prepared by melt mixing in the twin screw extruder. The grafting of VTES onto EPDM and its crosslinking was confirmed by FT‐IR. The characterization of mechanical properties such as tensile strength, elongation at break, Young's modulus and hardness, differential scanning calorimetry (DSC) analysis and morphology were studied and compared for the EPDM‐g‐VTES/LLDPE blends. The study reveals that the dynamically vulcanized blend improves the mechanical and thermal properties due to the presence of efficient interaction between component polymers when compared with other blends. Copyright © 2005 John Wiley & Sons, Ltd.     

Preparation and characterization of melt‐compounded polyethylene/vermiculite nanocomposites

Polyethylene (PE)‐layered vermiculite (VMT) nanocomposites were fabricated via direct melt compounding in a twin‐screw extruder followed by injection molding. Exfoliated PE/VMT nanocomposites were readily prepared via in situ melt mixing of maleic anhydride modified VMT with PE. Maleic anhydride acts as either the intercalation agent for VMT or as a compatibilizer for the PE and VMT phases. X‐ray diffraction and transmission electron microscopic observations revealed the formation of exfoliated PE/VMT nanocomposites. The experimental results showed that the storage modulus and strength of nanocomposites tend to increase with an increasing VMT content. Nearly 25.35% increment in the tensile strength and 50% increment in the storage modulus were achieved by incorporating 4 wt % VMT into PE. The thermal properties of the nanocomposites were investigated by dynamic mechanical analysis and differential scanning calorimetry. The glass‐transition temperature of PE/VMT nanocomposites appeared to increase upon the introduction of VMT into the PE matrix. The effects of maleic anhydride addition on the formation of the PE/VMT nanocomposites are discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1476–1484, 2003     

X‐ray studies on the double melting behavior of poly(butylene terephthalate)

The double melting behavior of poly(butylene terephthalate) (PBT) was studied with differential scanning calorimetry (DSC) and wide‐angle X‐ray analysis. DSC melting curves of melt‐crystallized PBT samples, which we prepared by cooling from the melt (250 °C) at various cooling rates, showed two endothermic peaks and an exothermic peak located between these melting peaks. The cooling rate effect on these peaks was investigated. The melt‐crystallized PBT sample cooled at 24 K min^?1 was heated at a rate of 1 K min^?1, and its diffraction patterns were obtained successively at a rate of one pattern per minute with an X‐ray measurement system equipped with a position‐sensitive proportional counter. The diffraction pattern did not change in the melting process, except for the change in its peak height. This suggests that the double melting behavior does not originate from a change in the crystal structure. The temperature dependence of the diffraction intensity was obtained from the diffraction patterns. With increasing temperature, the intensity decreased gradually in the low‐temperature region and then increased distinctly before a steep decrease due to the final melting. In other words, the temperature‐dependence curve of the diffraction intensity showed a peak that is interpreted as proof of the recrystallization in the melting process. The peak temperature was 216 °C. The temperature‐dependence curve of the enthalpy change obtained by the integration of the DSC curve almost coincided with that of the diffraction intensity. The double melting behavior in the heating process of PBT is concluded to originate from the increase of crystallinity, that is, recrystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2005–2015, 2001     

Preparation of oriented β‐form poly(L‐lactic acid) by solid‐state extrusion

Melt‐crystallized, low molecular weight poly(L ‐lactic acid) (PLLA) consisting of α crystals was uniaxially drawn by solid‐state extrusion at an extrusion temperature (T_ext) of 130–170 °C. A series of extrusion‐drawn samples were prepared at an optimum T_ext value of 170 °C, slightly below the melting temperature (T_m) of α crystals (～180 °C). The drawn products were characterized by deformation flow profiles, differential scanning calorimetry (DSC) melting thermograms, wide‐angle X‐ray scattering (WAXD), and small‐angle X‐ray scattering as a function of the extrusion draw ratio (EDR). The deformation mode in the solid‐state extrusion of semicrystalline PLLA was more variable and complex than that in the extensional deformation expected in tensile drawing, which generally gave a mixture of α and β crystals. The deformation profile was extensional at a low EDR and transformed to a parabolic shear pattern at a higher EDR. At a given EDR, the central portion of an extrudate showed extensional deformation and the shear component became progressively more significant, moving from the center to the surface region. The WAXD intensities of the (0010)_α and (003)_β reflections on the meridian as well as the DSC melting thermograms showed that the crystal transformation from the initial α form to the oriented β form proceeded rapidly with increasing EDR at an EDR greater than 4. Furthermore, WAXD showed that the crystal transformation proceeded slightly more rapidly at the sheath region than at the core region. This fact, combined with the deformation profiles (shear at the sheath and extensional at the core), indicated that the crystal transformation was promoted by shear deformation under a high pressure rather than by extensional deformation. Thus, a highly oriented rod consisting of only β crystals was obtained by solid‐state extrusion of melt‐crystallized, low molecular weight PLLA slightly below T_m. The structure and properties of the α‐ and β‐form crystals were also studied. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 95–104, 2002     

Study on In-Situ Compatibilization of the PP/PA6 Blends in Twin Screw Extruders

The in-situ compatibilization of PP/PA6 blend was studied in a twin screw extruder. The maleic anhydride (MA) content, peroxide concentration, shear rate and feeding order were among the variables investigated. Degree of grafting of samples collected prior to feeding of PA6 into the extruder was measured using titration combined with FTIR technique. From the SEM results it was found that the increasing of initial MA concentration led to larger PA particle size which could be related to secondary reactions between excess MA and PA. The melt linear viscoelastic measurements performed on the blend samples and the obtained relaxation time spectra showed shorter form relaxation time and interfacial relaxation time for one-step compatibilized sample compared to the sample prepared by the two-step method with the same degree of grafting. This was attributed to the stronger interfacial interaction of the one-step compatibilized blend samples which could be resulted from greater efficiency of grafting and/or compatibilization. These results were supported by SEM results which showed smaller particle size for the one-step compatibilized samples. It was demonstrated that melt linear viscoelastic measurement could provide a great insight into understanding the compatibilization process in twin screw extruder.     

Thermal analysis of the multiple melting behavior of poly(butylene succinate‐co‐adipate)

The melting behavior of poly(butylene succinate‐co‐adipate) (PBSA) isothermally crystallized from the melt was investigated by differential scanning calorimetry. Triple, double, or single melting endotherms were observed in subsequent heating scan for the samples isothermally crystallized at different temperatures. These endothermic peaks were labeled as I, II, and III for low‐, middle‐, and high‐temperature melting endotherms, respectively. The independence of endotherm III to the crystallization temperature, the existence of an exothermic crystallization peak just below the endotherm III, and the heating rate dependence of endotherm III indicated that endotherm III was due to the remelting of recrystallized lamellar during a heating scan. The influence of crystallization time on the melting behavior of PBSA showed that endotherms II and III developed prior to endotherm I; endotherm III developed rather simultaneously with endotherm II. Further investigation showed that the peak temperature of endotherm I increased linearly with the logarithm of the crystallization time. It suggested that endotherm II was attributed to the melting of the primary lamellae, while endotherm I was due to the melting of secondary lamellae. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3077–3082, 2005     

Temperature‐modulated differential scanning calorimetry studies on the origin of double melting peaks in isothermally melt‐crystallized poly(L‐lactic acid)

In this work, the melting behaviors of nonisothermally and isothermally melt‐crystallized poly(L ‐lactic acid) (PLLA) from the melt were investigated with differential scanning calorimetry (DSC) and temperature‐modulated differential scanning calorimetry (TMDSC). The isothermal melt crystallizations of PLLA at a temperature in the range of 100–110 °C for 120 min or at 110 °C for a time in the range of 10–180 min appeared to exhibit double melting peaks in the DSC heating curves of 10 °C/min. TMDSC analysis revealed that the melting–recrystallization mechanism dominated the formation of the double melting peaks in PLLA samples following melt crystallizations at 110 °C for a shorter time (≤30 min) or at a lower temperature (100, 103, or 105 °C) for 120 min, whereas the double lamellar thickness model dominated the formation of the double melting peaks in those PLLA samples crystallized at a higher temperature (108 or 110 °C) for 120 min or at 110 °C for a longer time (≥45 min). © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 466–474, 2007     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. II. Samples crystallized from the melt

The complex thermal behavior of poly(l ‐lactic acid) films crystallized from the melt, either isothermally or nonisothermally, was studied by differential scanning calorimetry (DSC), wide angle X‐ray diffraction, and small angle X‐ray scattering. The variation of the thermal behavior with crystallization temperature, time, and cooling rate was documented and analyzed. After nonisothermal crystallization at low cooling rates that develop high crystallinity, an obvious double melting peak appears at modest heating rates (e.g., 10 °C/min). At higher heating rates, these samples exhibit only single melting. However, an unusual form of double melting occurs under the majority of the conditions studied under either isothermal or nonisothermal conditions. In this case, double melting is marked by the appearance of a recrystallization exotherm just prior to the final melting that obscures the observation of the melting of the crystals formed during the initial crystallization process. The occurrence of double melting in melt‐crystallized samples was concluded to be the result of a melt‐recrystallization process occurring during the subsequent DSC heating scan; it is a function of crystalline perfection, not the initial crystallinity, nor whether or not the crystallization reached completion at the crystallization temperature. Many other very interesting observations are also discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3378–3391, 2006     

Polyamide‐6,6‐based blocky copolyamides obtained by solid‐state modification

Copolyamides based on polyamide‐6,6 (PA‐6,6) were prepared by solid‐state modification (SSM). Para‐ and meta‐xylylenediamine were successfully incorporated into the aliphatic PA‐6,6 backbone at 200 and 230 °C under an inert gas flow. In the initial stage of the SSM below the melting temperature of PA‐6,6, a decrease of the molecular weight was observed due to chain scission, followed by a built up of the molecular weight and incorporation of the comonomer by postcondensation during the next stage. When the solid‐state copolymerization was continued for a sufficiently long time, the starting PA‐6,6 molecular weight was regained. The incorporation of the comonomer into the PA‐6,6 main chain was confirmed by size exclusion chromatography (SEC) with ultraviolet detection, which showed the presence of aromatic moieties in the final high‐molecular weight SSM product. The occurrence of the transamidation reaction was also proven by ¹H nuclear magnetic resonance (NMR) spectroscopy. As the transamidation was limited to the amorphous phase, this SSM resulted in a nonrandom overall structure of the PA copolymer as shown by the degree of randomness determined using ¹³C NMR spectroscopy. The thermal properties of the SSM products were compared with melt‐synthesized copolyamides of similar chemical composition. The higher melting and higher crystallization temperatures of the solid state‐modified copolyamides confirmed their nonrandom, block‐like chemical microstructure, whereas the melt‐synthesized copolyamides were random. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5118–5129