Synthesis of Aqueous CdTe Nanocrystals with High Efficient Blue‐Green Emission of Exciton

As one of the most popular nanocrystals (NCs), aqueous CdTe NCs have very weak green emission under conventional synthesis conditions. In this work, we report the first example of blue‐emitting CdTe NCs directly synthesized in aqueous solution by slowing down the growth rate after nucleation. The key for the synthesis is the optimization of NC growth conditions, namely pH range of 7.5 to 8.5, TGA/Cd ratio of 3.6, Cd/Te ratio of 10, and Te concentration of 2×10^?5 mol/L, to get a slow growth rate after nucleation. The as‐prepared blue‐emitting CdTe NCs have small size (as small as 1.9 nm) and bright emission [with 4% photoluminescence quantum yield (PL QY) at 486 nm and 17% PLQY at 500 nm]. Transmission electron microscopy (TEM) images of the as‐prepared CdTe show monodispersed NCs which exhibit cubic zinc blend structure. Moreover, time‐resolved PL decay and X‐ray photoelectron spectroscopy (XPS) results show the as‐prepared NCs have better surface modification by ligand, which makes these luminescent small CdTe NCs have higher photoluminescence quantum yield, compared with NCs synthesized under conventional conditions.     

Special characteristics of fluorescence and resonance Rayleigh scattering for cadmium telluride nanocrystal aqueous solution and its interactions with aminoglycoside antibiotics

CdTe nanocrystals (CdTe NCs) were achieved by reaction of CdCl₂ with KHTe solution and were capped with sodium mercaptoacetate. The product was detected by transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), energy dispersive spectroscopy (EDS), fluorescence spectra, ultraviolet-visible spectra and X-ray diffraction (XRD). The CdTe NCs are of cubic structure and the average size is about 5 nm. The fluorescence quantum yield of CdTe NCs aqueous solution increased from 37% to 97% after 20 d under room light. The maximum λ _em of fluorescence changed from 543 nm to 510 nm and the blue shift was 33 nm. CdTe NCs aqueous solution can be steady for at least 10 months at 4 in° a refrigerator. The resonance Rayleigh scattering (RRS) of CdTe NCs in the aqueous solution was investigated. The maximum scattering peak was located at about 554 nm. The interactions of CdTe NCs with amikacin sulfate (AS) and micronomicin sulfate (MS) were investigated respectively. The effects of AS and MS on fluorescence and RRS of CdTe NCs were analyzed. It was found that AS and MS quenched the photoluminescence of CdTe NCs and enhanced RRS of CdTe NCs. Under optimum conditions, there are linear relationships between quenching intensity (F ₀-F), intensity of RRS (I-I ₀) and concentration of AS and MS. The detection limits (3б) of AS and MS are respectively 3.4 ng·mL⁻¹ and 2.6 ng·mL⁻¹ by the fluorescence quenching method, and 15.2 ng·mL⁻¹ and 14.0 ng·mL⁻¹ by the RRS method. The methods have high sensitivity, thus CdTe NCs may be used as fluorescence probes and RRS probes for the detection of aminoglycoside antibiotics. Supported by the National Natural Science Foundation of China (Grant No. 20475045)     

巯基乙胺稳定的水溶性CdTe纳米粒子的合成与表征

用巯基乙胺(cysteamine，CA)作为稳定剂，在水相中合成了发光可调的CdTe半导体纳米粒子。这些巯基乙胺稳定的CdTe纳米粒子表面带有大量的正电荷。实验结果表明，稳定剂与Cd的比例以及pH等实验条件对CdTe纳米粒子体系的荧光发射强度影响较大。在pH为6.1时，纳米粒子体系在橙红波段的荧光量子产率达到了9%左右。控制实验条件，合成了各种尺寸的CdTe纳米粒子，荧光发射光谱在520～600 nm范围连续可调。分别用X射线光电子能谱(XPS)，透射电子显微镜(TEM)，X射线衍射仪(XRD)，红外吸收     

Er3+/Yb3+共掺纳米In2O3的制备及上转换发光

用低温溶剂热法以乙二醇为溶剂合成了Er3+和Yb3+共掺的In2O3纳米晶。用X射线衍射(XRD)、透射电镜(TEM)、漫反射光谱和上转换发光光谱对样品进行了分析。XRD和TEM结果表明,产物为纯的立方相In2O3结构,粒径约为30 nm;漫反射光谱显示了In2O3∶Er3+,Yb3+纳米晶在522、653和975 nm附近有3个吸收带;在980 nm近红外光激发下,样品发射出中心波长为525及555 nm的绿光和662 nm的红光,分别对应于Er3+的2H11/2→4I15/2、4S3/2→4I15/2和4F9/2→4I15/2跃迁;研究了Er3+和Yb3+离子的不同掺杂浓度对发光强度的影响,确定了Yb3+和Er3+离子的最佳掺杂浓度均为3%;双对数曲线显示绿光和红光的发射过程均为双光子吸收过程,对样品的上转换发光机制进行了初步讨论。     

Synthesis of Multifunctional Mn‐Doped CdTe/ZnS Core/Shell Quantum Dots

The synthesis of a novel water‐soluble Mn‐doped CdTe/ZnS core‐shell quantum dots using a proposed ultrasonic assistant method and 3‐mercaptopropionic acid (MPA) as stabilizer is descried. To obtain a high luminescent intensity, post‐preparative treatments, including the pH value, reaction temperature, reflux time and atmosphere, have been investigated. For an excellent fluorescence of Mn‐doped CdTe/ZnS, the optimal conditions were pH 11, reflux temperature 100°C and reflux time 3 h under N₂ atmosphere. While for phosphorescent Mn‐doped CdTe/ZnS QDs, the synthesis at pH 11, reflux temperature 100°C and reflux time 3 h under air atmosphere gave the best strong phosphorescence. The characterizations of Mn‐doped CdTe/ZnS QDs were also identified using AFM, IR, powder XRD and thermogravimetric analysis. The data indicated that the photochemical stability and the photoluminescence of CdTe QDs are greatly enhanced by the outer inorganic ZnS shell, and the doping Mn²⁺ ions in the as‐prepared quantum dots contribute to strong luminescence. The strong luminescence of Mn‐doped CdTe/ZnS QDs reflected that Mn ions act as recombination centers for the excited electron‐hole pairs, attributing to the transition from the triplet state (⁴T₁) to the ground state (⁶A₁) of the Mn²⁺ ions. All the experiments demonstrated that the surface states played important roles in the optical properties of Mn‐doped CdTe/ZnS core‐shell quantum dots.     

Detection of Hg2+ and F− Ions by Using Fluorescence Switching of Quantum Dots in an Au‐Cluster–CdTe QD Nanocomposite

A single probe of an Au nanocluster–CdTe quantum dots nanocomposite has been developed by using tripeptide‐capped CdTe quantum dots (QD) and bovine serum albumin (BSA) protein‐conjugated Au₂₅ nanocluster (NC) for detection of both Hg²⁺ ion and F^? ion. The formation of Au‐NC–CdTe QD nanocomposite has been confirmed by TEM, steady state and time resolved spectroscopy, CD and FTIR studies. A significant signal off (74 % PL quenching at 553 nm) phenomenon of this nanocomposite is observed in presence of 6.56×10^?7 M Hg²⁺ ion, due to salt‐induced aggregation. However, a dramatic PL enhancement (128 %) of the Au‐NC–CdTe QD nanocomposite is observed in presence of 8.47×10^?7 M F^? anion. The calculated limit of detections (LOD) of Hg²⁺ ion concentration and F^? ion concentration are found to be 9 and 117 nM , respectively, which are within the safety range set by the United States Environment Protection Agency. Thus, the simple Au‐NC–CdTe QD optical‐based sensor is very useful to detect both toxic cations and anions.     

Novel Strategy for Synthesis of High Quality CdTe Nanocrystals in Aqueous Solution

A novel aqueous route for the synthesis of high-quality CdTe nanocrystals（NCs） is presented in this article. With both glutathione（GSH） and cysteine[n（GSH）：n（cysteine）=1：3] as stabilizers, high-quality CdTe NCs with controllable photoluminescence（PL） wavelength from 500 to 630 nm can be prepared within 4 h. As-prepared CdTe NCs show higher photoluminescence quantum yields（PLQY） compared with CdTe NCs prepared via other aqueous methods. When the fluorescent emission peak appeared in orange-red window, the PLQY reaches 70% or above at room temperature without any post-preparative treatment.     

Energy Migration Upconversion in Manganese(II)‐Doped Nanoparticles

We report the synthesis and characterization of cubic NaGdF₄:Yb/Tm@NaGdF₄:Mn core–shell structures. By taking advantage of energy transfer through Yb→Tm→Gd→Mn in these core–shell nanoparticles, we have realized upconversion emission of Mn²⁺ at room temperature in lanthanide tetrafluoride based host lattices. The upconverted Mn²⁺emission, enabled by trapping the excitation energy through a Gd³⁺ lattice, was validated by the observation of a decreased lifetime from 941 to 532 μs in the emission of Gd³⁺ at 310 nm (⁶P_7/2→⁸S_7/2). This multiphoton upconversion process can be further enhanced under pulsed laser excitation at high power densities. Both experimental and theoretical studies provide evidence for Mn²⁺ doping in the lanthanide‐based host lattice arising from the formation of F^? vacancies around Mn²⁺ ions to maintain charge neutrality in the shell layer.     

Size‐Tunable Highly Luminescent SiO2 Particles Impregnated with Number‐Adjusted CdTe Nanocrystals

Highly luminescent SiO₂ particles impregnated with CdTe nanocrystals (NCs) are prepared by a sol–gel procedure. Partial ligand exchange from thioglycolic acid to 3‐mercaptopropyltrimethoxysilane (MPS) on the NCs enables retention of the initial photoluminescence (PL) efficiency of the NCs in water, while the simultaneous addition of a poor solvent (ethanol) results in regulated assembly of the NCs through condensation of hydrolyzed MPS. The SiO₂ particles thus prepared have, for example, a diameter of 16 nm and contain three NCs each. The PL efficiency of these particles is 40 %, while the initial efficiency is 46 % in a colloidal solution. The redshift and narrowed spectral width in PL observed after impregnation indicate that the concentration of NCs in these nearly reaches the ultimate value (on the order of 10²¹ particles per liter). The porosity of these particles is investigated by means of N₂ adsorption–desorption isotherms. Due to the SiO₂ shell, these particles have higher stability in phosphate‐buffered saline buffer solution than the initial NCs. Their potential use for labeling in bio‐applications is investigated by conjugating biotinylated immunoglobulin G to them by using streptavidin maleimide as linker. Successful conjugation is confirmed by electrophoresis in agarose gel. This preparation method is an important step towards fabricating intensely emitting biocompatible SiO₂ particles impregnated with semiconductor NCs.     

Preparation and photoluminescence properties of RE:Na3La9O3(BO3)8 (RE=Er, Yb) crystals

Using Na₂CO₃-H₃BO₃-NaF as fluxes, transparent RE:Na₃La₉O₃(BO₃)₈ (abbr. RE:NLBO, RE=Er, Yb) crystals have been grown by the top seed solution growth (TSSG) method. The X-ray powder diffraction analysis shows that the RE:NLBO crystals have the same structure with NLBO. The element contents were determined by molar to be 0.64% Er³⁺ in Er:NLBO, 2.70% Yb³⁺ in Yb:NLBO, respectively. The polarized absorption spectra of RE:NLBO have been measured at room temperature and show that both Er:NLBO and Yb:NLBO have a strong absorption bands near 980 nm with wide FWHM (Full Wave at Half Maximum) (21 nm for Er:NLBO and 25 nm for Yb:NLBO). Fluorescence spectra have been recorded. Yb:NLBO has the emission peaks at 985 nm, 1028 nm and 1079 nm and the emission peak of Er:NLBO is at 1536 nm. Spectral parameters have been calculated by the Judd-Ofelt theory for Er:NLBO and the reciprocity method for Yb:NLBO, respectively. The calculated values show that Er:NLBO is a candidate of 1.55 μm laser crystals and Yb:NLBO is a candidate for self-frequency doubling crystal.     

Synthesis of CdTe/SiO_2 Composites and Their Fluorescence Properties

Thioglycolic acid(TGA)-stabilized CdTe nanocrystals(NCs) were prepared with sodium tellurite as tellurium source,which avoids the cumbersome processes associated with H2Te or NaHTe sources.Fluorescent CdTe/SiO2 composites were synthesized by a sol-gel method without the exchange of surface ligands.The phase structure of CdTe NCs was investigated by X-ray diffractometry.For comparison,some characterizations were done for both the CdTe NCs and the composites.CdTe NCs and CdTe/SiO2 composites were characterize...     

Yb:Er:Tm:LiTaO3的上转换发白光性能研究

980 nm脉冲激光激发下,首次通过高温固相法制备Yb(10%):Er(1%):Tm(1%):LiTaO3(摩尔分数)多晶粉并实现室温上转换白光.X射线粉末衍射测试结果表明,Yb:Er:Tm:LiTaO3中的掺杂离子并没有改变晶格结构,以取代的方式存在于钽酸锂晶格中.结合功率曲线测试结果和上转换机制研究发现,产生上转换蓝光的Tm3+离子1G4态的布居主要来自双光子同时吸收过程.而单光子上转换输出的红光,则由Tm3+和Er3+离子之间的交叉弛豫过程产生,即3F2/3(Tm3+)+4I15/2(Er3+)→3H6(Tm3+)+4I9/2(Er3+).上转换绿光来源于Yb/Er离子对的二次能量传递.     

Effect of CdS Interlayer on Properties of CdTe Based Quantum Dots

Highly luminescent thioglycolic acid-capped CdTe-based core/shell quantum dots (QDs) were synthesized through encapsulating CdTe QDs in various inorganic shells including CdS, ZnS and CdZnS. CdTe/CdS core/shell QDs exhibited a significant redshift of emission peaks (a maximum emission peak of 652 nm for the core/shell QDs and 575 nm for CdTe cores) with increasing shell thickness. In contrast, the redshift of photoluminescence (PL) peak wavelength of CdTe/ZnS QDs was less than 15 nm. The PL peak wavelengths of the core/shell QDs depended strongly on core size and shell thickness. The PL quantum yields (QYs) of the CdTe/CdS core/shell QDs are up to 67 % while that of CdTe/ZnS core/shell QDs is 45 %. A composite CdZnS shell made CdTe cores a high PL QY up to 51 % and broadly adjusted PL spectra (a maximum PL peak wavelength of 664 nm). The epitaxial growth of the shell was confirmed by X-ray powder diffraction analysis and luminescence decay experiments. Because of high PL QYs, tunable PL spectra, and low toxicity from a ZnS surface layer, CdTe/CdZnS core/shell QDs will be great potential for bioapplications.     

Selective Detection of Mercury（Ⅱ） and Copper（Ⅱ） Based on the Opposite Size-dependent Fluorescence Quenching of CdTe Quantum Dots

Three different size CdTe quantum dots （QDs） capped by 3-mercaptopropionic acid （MPA） have been prepared in aqueous solutions, and their interactions with Cu^2＋ and Hg^2＋ have been investigated. The opposite size-dependent fluorescence quenching of CdTe QDs by Hg^2＋ and Cu^2＋ was observed： Hg^2＋ quenched smaller particles more efficiently than larger ones while larger particles were more markedly quenched by Cu^2＋. Based on the different size responses, Hg^2＋ and Cu^2＋ were respectively detected with high sensitivity and selectivity, for the first time, using the QDs with different sizes but the same components and capping ligands.     

量子点荧光探针检测抗坏血酸

以巯基丙酸（MPA）为稳定剂水相合成了高荧光CdTe量子点. 向量子点溶液中加入Mn2+,由于量子点表面状态发生改变而使其荧光淬灭,加入抗坏血酸后量子点荧光又得以恢复,且荧光恢复程度与抗坏血酸的浓度线性相关,从而建立了基于量子点的荧光“开关”探针检测抗坏血酸的新方法. 当CdTe量子点的浓度为1.67 uM（量子点的尺寸为1.91nm）,加入的Mn2+浓度为0.25 mM时,在优化的实验条件下,检测抗坏血酸的线性范围为0.25~16 uM,检出限为36 nM. 相对标准偏差为2.5%(10 uM, n=11). 该探针可用于维生素C药片和人血浆中抗坏血酸的快速、灵敏和选择性检测.     

Preparation and Optical Properties of CdTe/CdO-nH2O Core/shell Nano-composites in Aqueous Solution

"The deposition of CdO?nH2O on CdTe nanoparticles was studied in an aqueous phase. The CdTe nanocrystals (NCs) were prepared in aqueous solution through the reaction between Cd2+ and NaHTe in the presence of thioglycolic acid as a stabilizer. The molar ratio of the Cd2+ to Te2- in the precursory solution played an important role in the photoluminescence of the ultimate CdTe NCs. The strongest photoluminescence was obtained under 4.0 of Cd2+/Te2- at pH?8.2. With the optimum dosage of Cd(II) hydrous oxide deposited on the CdTe NCs, the photoluminescence was enhanced greatly. The photoluminescence of these nanocomposites was kept constant in the pH range of 8.0-10.0, but dramatically decreased with an obvious blue-shifted peak while the pH was below 8.0. In addition, the photochemical oxidation of CdTe NCs with cadmium hydrous oxide deposition was markedly inhibited."     

Multi-spectroscopic Study on the Interaction between CdTe Quantum Dots and Bovine Serum Albumin

The interaction between CdTe quantum dots (QDs) and bovine serum albumin (BSA) was systematically investigated by fluorescence, UV‐vis absorption and circular dichroism (CD) spectroscopy under physiological conditions. The experimental results showed that the fluorescence of BSA could be quenched by CdTe QDs with a static quenching mechanism, indicating that CdTe QDs could react with BSA. The quenching constants according to the modified Stern‐Volmer equation were obtained as 1.710×10⁶, 1.291×10⁶ and 1.010×10⁶ L·mol^?1 at 298, 304, and 310 K, respectively. ΔH, ΔS and ΔG for CdTe QDs‐BSA system were calculated to be ?33.68 kJ·mol^?1, 6.254 J·mol^?1·K^?1 and ?35.54 kJ·mol^?1 (298 K), respectively, showing that electrostatic interaction in the system played a major role. According to F?rster theory, the distance between Trp‐214 in BSA and CdTe QDs was given as 2.18 nm. The UV‐vis, synchronous fluorescence and CD spectra confirmed further that the conformations of BSA after addition of CdTe QDs have been changed.     

CdTe nanocrystals sensitized chemiluminescence and the analytical application

It was found that the mixing of CdTe semiconductor nanocrystals (NCs) with luminol in the presence of KMnO₄ can induce a great sensitized effect on chemiluminescence (CL) emission. When the concentration of luminol, KMnO₄ and NaOH were fixed at 1 μM, 1 μM and 0.05 M, respectively, the most excellent performance can be obtained for the CdTe NCs sensitized CL. By means of CL and photoluminescence spectra, we suppose the enhanced CL signals resulted from the accelerated luminol CL induced by the oxidized species of CdTe NCs. Based on the finding, using thioglycolic acid-capped CdTe NCs as label and immunoglobulin G (IgG) as a model analyte, a CL immunoassay protocol for IgG content detection was developed. The strong inhibition effect of phenol compounds on luminol-KMnO₄-CdTe NCs CL system was also observed. All these findings demonstrated the possibility of semiconductor nanocrystals induced chemiluminescence to be utilized for more practical applications.     

Synthesis and characterization of high-quality ZnS, ZnS:Mn2+, and ZnS:Mn2+/ZnS (core/shell) luminescent nanocrystals

High-quality ZnS, ZnS:Mn2+, and ZnS:Mn2+/ZnS (core/shell) nanocrystals (NCs) were synthesized via a high-boiling solvent process and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), electron paramagnetic resonance (EPR), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectra. The monodisperse ZnS NCs (size = 8 nm), which self-assembled into several micrometer-sized domains, were achieved by adopting poly(ethylene glycol) (PEG) in the reaction process (without using a size-selection process). The obtained ZnS:Mn2+ and ZnS:Mn2+/ZnS core/shell NCs are highly crystalline and quasimonodisperse with an average particle size of 6.1 and 8.4 nm, respectively. All of the as-formed NCs can be well dispersed in hexane to form stable and clear colloidal solutions, which show strong visible emission (blue for ZnS and red-orange for ZnS:Mn2+ and ZnS:Mn2+/ZnS) under UV excitation. The growth of a ZnS shell on ZnS:Mn2+ NCs, that is, the formation of ZnS:Mn2+/ZnS core/shell NCs, resulted in a 30% enhancement in the PL intensity with respect to that of bare ZnS:Mn2+ NCs due to the elimination of the surface defects.     

NaYF4∶Er3＋, Yb3＋纳米晶的液相合成

采用丙三醇液相结晶法制备了NaYF4∶Er3＋, Yb3＋上转换纳米晶, 合成步骤被简化. 常温下, 用980 nm的红外激光激发可以观察到很强的绿光、红光发射, 用荧光光谱仪记录了该上转换光谱. X射线粉末衍射(XRD)结果表明, 该方法制备NaYF4∶Er3＋, Yb3＋纳米晶属于立方混合六方晶系. 研究了纳米晶的上转换发光机理, 根据晶体场理论对Er3＋的两个上转换能级进行了Stark分裂计算, 对两个能级之间的谱线进行了归属, 进一步证实了980 nm光子激发Er3＋离子的上转换机理, 一个是连续吸收两个980 nm光子的过程(激发态吸收), 另一个是吸收980 nm光子后, 电子转移到亚稳态能级, 然后再吸收980 nm光子过程(能量转移上转换).