Ag-TiO_2/ACF纳米复合物的制备及其对亚甲基兰光降解作用及抗菌性能

以钛酸四丁酯为前躯体,活性炭纤维(ACF)为载体,蔗醣为粘结剂,采用真空吸附水解法制备了TiO2/ACF催化剂.通过在TiO2/ACF表面负载上银纳米颗粒,制得Ag-TiO2/ACF光降解-抗菌复合材料.利用BET、XRD、SEM等方法对其进行了表征.研究了Ag-TiO2/ACF在光照下对亚甲基兰的降解作用和对大肠杆菌的杀灭效果.结果表明,光照2h,Ag-TiO2/ACF可以将溶液中亚甲基兰降解97%以上.当纳米复合材料中Ag含量为0.75wt%时,Ag-TiO2/ACF对大肠杆菌具有很强的灭杀作用.     

Gd掺杂TiO2/活性炭纤维复合材料的制备及表征

以TiCl4和Gd(NO3)3·6H2O为主要原料,采用酸催化水解法制备Gd掺杂TiO2光催化剂并通过浸涂法将其负载在活性炭纤维(ACF)表面,制得Gd掺杂TiO2/ACF复合材料。 以气相苯为模型物,考察材料的光催化活性。 利用XRD、FTIR及GC-MS对催化剂的晶相结构、光谱特征等进行了表征。 结果表明,Gd掺杂能有效抑制TiO2的晶粒生长。 Gd掺杂量、浸涂次数影响TiO2/ACF光催化活性,Gd2O3掺杂质量分数为0.48%、浸涂2次的TiO2/ACF活性最高。 在苯光催化氧化后的Gd掺杂TiO2/ACF复合材料表面未发现醌类中间产物的存在。 Gd的掺入能减缓催化剂失活,光催化反应100 min后仍能表现出较高活性。     

Gd掺杂TiO2/活性炭纤维复合材料的制备及表征

以TiCl4和Gd(NO3)3·6H2O为主要原料,采用酸催化水解法制备Gd掺杂TiO2光催化剂并通过浸涂法将其负载在活性炭纤维(ACF)表面,制得Gd掺杂TiO2/ACF复合材料。 以气相苯为模型物,考察材料的光催化活性。 利用XRD、FTIR及GC-MS对催化剂的晶相结构、光谱特征等进行了表征。 结果表明,Gd掺杂能有效抑制TiO2的晶粒生长。 Gd掺杂量、浸涂次数影响TiO2/ACF光催化活性,Gd2O3掺杂质量分数为0.48%、浸涂2次的TiO2/ACF活性最高。 在苯光催化氧化后的Gd掺杂TiO2/ACF复合材料表面未发现醌类中间产物的存在。 Gd的掺入能减缓催化剂失活,光催化反应100 min后仍能表现出较高活性。     

TiO_2/ACF光催化剂的超声波制备及其光催化活性

本文以超声波为晶化方法在低温下制得了炭纤维负载的Ti O2光催化剂(Ti O2/ACF)。通过X衍射、扫描电镜、液氮吸附等对晶化中所得催化剂Ti O2的晶型、形貌和织构进行了考察,并以甲基橙为降解物考察了催化剂活性。结果表明:在超声波作用下,Ti O2前驱体先被均匀负载到炭纤维表面,然后被晶化为14.2 nm的锐钛矿粒子;所得催化剂晶粒在炭纤维表面形成了1.1nm左右的微孔,其介孔体积比炭纤维高;超声晶化时间对晶粒大小无明显影响,但对催化剂活性有重要活性影响:60分钟的晶化活性最好,过长时间会使负载的Ti O2脱落,降低催化剂活性。实验结果还表明,Ti O2/ACF催化剂在重复使用中活性基本稳定,且对甲基橙吸附比原炭纤维高,其原因在于催化剂介孔体积的增加。     

TiO2/ACF的制备及光催化降解四氯乙烯性能

以钛酸四丁酯为前驱物,活性炭纤维(ACF)为载体,蔗糖为胶粘剂,采用真空吸附水解的方法制得了TiO₂/ACF催化剂.采用BET、XRD、SEM等手段对其物理化学特性进行表征,以四氯乙烯光降解反应为探针反应,考察了TiO₂/ACF催化剂的光催化降解性能.实验结果表明,采用真空吸附水解法可以将TiO₂很好地负载到活性炭纤维表面上.通过优化条件制备的TiO₂/ACF催化剂在光照2h条件下,可以将水中溶解量的四氯乙烯降解90%以上.催化剂可以多次循环使用,光催化反应活性不变.     

SiO2负载的TiO2光催化剂可见光催化降解染料污染物

 采用酸催化溶胶-凝胶法制备了SiO2负载的TiO2光催化剂,考察了制备条件对负载型TiO2光催化剂的晶相、结构、比表面积和可见光催化活性的影响. 结果表明,采用SiO2为载体时,TiO2以纳米颗粒的形态分散在载体表面,负载型TiO2/SiO2催化剂的比表面积大、等电点低而且热稳定性能良好. 偶氮染料酸性橙7的可见光催化降解实验结果表明,染料污染物在催化剂表面的吸附是影响催化剂可见光催化活性的重要因素. 与试剂TiO2样品相比,负载型TiO2/SiO2光催化剂具有更好的光催化活性和沉降性能.     

TiO2/AC复合光催化剂对苯和丁醛的气相光催化降解机理

 利用溶胶-凝胶并水热处理法制备了TiO2光催化剂和TiO2/AC复合光催化剂,在静态光催化反应器中研究了苯和丁醛的气相吸附和光催化降解,利气相色谱分析确定了生成的中间体. 结果表明, TiO2/AC复合光催化剂比TiO2光催化剂具有较强的吸附能力和较高的光催化活性; 在TiO2和TiO2/AC上,苯(或丁醛)光催化降解产生相同的中间体,表明在两种催化剂上发生的光催化反应遵循相同的机理,进而讨论了其可能的光催化氧化途径.     

TiO2/BixTiyOz气相光催化降解苯的动力学模型及反应机理

在密闭不锈钢反应器内考察了TiO2/BixTjyOz催化剂气相光催化降解苯的性能.结果表明,TiO2负载于Bi12TiO20,Bi2Ti2O7和Bi4Ti3O12上制成的催化剂,光催化活性得到很人的提高,TiO2最佳负载量为2.0%;其中,TiO2/Bi12TiO20的光催化活性最高,苯最高转化率是纯TiO2的2倍,催化剂使用寿命也延长了1倍.在本文实验条件下,TiO2/Bi12TiO20上苯气相光催化降解符合Lang-muir-Hinshelwood动力学模型,光催化反应速率常数k和Langmuir吸附常数K分别为0.006 4mg/(L·min)和9.670 2L/mg.采用红外光谱对失活的催化剂进行表征,结果表明催化剂表面出现了羰基与羟基等的振动峰,同时检测到主要的中间产物是2,6-二叔丁基-4-甲基苯酚,它吸附在催化剂表面活性化上而导致催化剂失活.最后推测了苯在催化剂表面气相光催化降解的反应机理.     

TiO2/AC复合催化剂光催化降解气相1,2-二氯苯

以商品活性炭(AC)为载体, 采用溶胶-凝胶法制备不同比表面积和TiO2负载量不同的光催化剂(TiO2/AC). 用氮吸附、X射线衍射(XRD)、扫描电子显微镜(SEM)等表征方法, 获得了所制备的TiO2/AC性能参数; 并通过降解气相1,2-二氯苯(1,2-DCBz)的实验研究了TiO2/AC催化剂的光催化氧化性能, 主要考察参数包括催化剂使用量、比表面积、气相1,2-DCBz浓度等对光催化氧化的影响. 结果表明: 负载于AC上的TiO2颗粒粒径为10 nm左右, TiO2颗粒负载在大比表面积的载体AC上有利于光催化降解气相1,2-DCBz. 通过比较商用P25和自制TiO2/AC光催化剂对气相1,2-DCBz的降解效果, 证明了AC吸附作用和TiO2光催化降解的协同作用使TiO2/AC光催化剂对气相1,2-DCBz的降解效率有较显著的提高.     

TiO2/活性炭负载型光催化剂的溶胶-凝胶法合成及表征

以钛酸四丁酯为钛源,采用溶胶-凝胶法在多孔活性炭(AC)表面合成TiO2前驱体,在氮气保护下程序升温处理制得TiO2/AC负载型光催化剂.采用X射线衍射、漫反射光谱、傅里叶变换红外光谱、扫描电镜、能量色散谱和低温液氮吸附等对光催化剂晶相结构、光谱特征及表面结构进行了表征.结果表明,AC可提高TiO2分散性能,降低TiO2团聚体的尺寸,并抑制其由锐钛矿相向金红石相的转变.TiO2与AC接触界面处有Ti-O-C键生成.另外,AC的含量对TiO2的能阈结构和晶粒大小影响不大.苯酚溶液的光催化降解测试结果表明,AC负载可为TiO2提供高浓度反应环境,适宜量的负载可显著提高TiO2对有机稀溶液的光催化降解活性.对于50mg/L苯酚的光催化降解,AC的质量分数分别为5%,9%和11%时催化剂协同系数分别为1.1,1.5和1.3.循环使用7次后,AC含量为9%的催化剂对苯酚的降解率仍达95.84%.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.