Effect of annealing on self-organized gradient film obtained from poly(3-[tris(trimethylsilyloxy)silyl] propyl methacrylate-co-methyl methacrylate)/poly(methyl methacrylate-co-n-butyl acrylate) blend latexes

The effect of annealing on the self-organized morphology and component gradient distribution of films prepared from bimodal latexes blend containing 1:1 silicon-containing acrylate copolymer/silicon-free acrylate copolymer blend was studied using attenuated total reflectance–Fourier transform infrared (ATR-FTIR) spectroscopy, scanning electron microscopy with X-ray energy-dispersive (SEM-EDX) spectrometry, and atomic force microscopy (AFM). The distribution of silicon through the whole thickness of the film as a function of annealing was investigated using confocal Raman spectroscopy (CRS). AFM results show that poly(methyl methacrylate-co-n-butyl acrylate) latex fuses to form a continuous film at 25?°C. The wettability of the acrylate components and the heterogeneous composition of poly(3-[tris(trimethylsilyloxy)silyl] propyl methacrylate-co-methyl methacrylate) result in a graded block film. ATR-FTIR and SEM-EDX measurements reveal silicon-containing components segregate at the film–air interface upon annealing. CRS further shows that the nonlinear model gradient distribution of silicon is obtained, where the content of silicon component is enhanced and it gradually varies in the bulk. When the annealing temperature increases to 120 and 180?°C, blend latexes films demonstrate varying topography and phase images, indicating phase separation is induced by annealing. Furthermore, CRS implies that the destruction of the gradient structure is attributed to the phase separation of the two blend components.     

SEED SEMICONTINUOUS EMULSION MULTI-COPOLYMERIZATION OF (METH) ACRYLATES WITH HIGH-SOLID CONTENT: EFFECT OF THE OPERATION CONDITIONS

The seeded semicontinuous emulsion multi-copolymerization of butyl acrylate (BA),2-ethylhexyl acrylate (2EHA), methyl methacrylate (MMA), 2-hydroxyl propyl acrylate(HOPA) and acrylic acid (AA) was used to prepare the acrylic latexes with high-solidcontent. The effects of monomer emulsion feed rates (R_a) and (R/E)_E values, the ratio ofemulsifier amount between the initial charge (R) and the addition monomer emulsion (E),on the polymerization reaction features, the viscosities, surface tensions,particle sizes andparticle sizes distributions of latexes,T_g and the insoluble fractions of films, the 180° peelstrength, tack and holding power of pressure-sensitive adhesive (PSA) tapes, preparedfrom the latexes, were studied. Experimental study shows that the grafting and cross-linking fraction in the PSA tapes must be controlled within a suitable range to keep thebalance of the 180° peel strength, tack and holding power.     

Emulsion Copolymerization of Vegetable Oil Macromonomers Possessing both Acrylic and Allylic Functionalities

Summary: A soybean oil-based vegetable oil macromonomer (VOMM) was incorporated as a comonomer into an all-acrylic copolymer via semi-continuous emulsion polymerization. Structurally, VOMMs are comprised of long hydrocarbon fatty acid moieties with allylic double bonds which enable auto-oxidative crosslinking at ambient temperature. VOMMs facilitate low temperature film formation and the fatty acid chains tethered to the polymer backbone auto-oxidize upon film formation to yield crosslinked films. Latexes with varying VOMM levels were synthesized to elucidate the effect of VOMMs on the pre-cure and post-cure glass transition temperature (T_g) and minimum film formation temperature (MFT). Thermoplastic control latexes (without VOMM) were also synthesized via copolymerization of butyl acrylate and methyl methacrylate. This paper details the characterization performed to validate and quantify the VOMM allylic unsaturation retention before, during, and after polymerization, and to quantify and confirm the increase in T_g resulting from auto-oxidative crosslinking via solid state ¹³C nuclear magnetic resonance spectroscopy and differential scanning calorimetry.     

氟含量对含氟丙烯酸酯共混乳胶膜梯度结构和表面性能的影响

首先将制备出的平均粒径较小的含氟丙烯酸酯均聚物乳液与平均粒径较大的纯丙烯酸酯共聚物乳液按不同的比例( 1/9,2/8,3/7,4/6,5/5)共混,接着将各共混乳液在室温下(20℃)玻璃基材上干燥后,于110℃/210℃下热处理一段时间.运用接触角法,XPS、AFM、SEM-EDX等详细研究了共混乳胶膜中含氟组分含量对...     

Batch and semicontinuous emulsion copolymerization of vinyl acetate–butyl acrylate. II. Morphological and mechanical properties of copolymer latex films

Vinyl acetate/(VAc)-butyl acrylate/(BuA) copolymer latex films of various copolymer compositions were investigated for their morphological properties by electron microscopy techniques, and for their mechanical properties by dynamic mechanical spectroscopy (DMS), differential scanning calorimetry (DSC), and tensile strength measurements. Batch copolymer latex films showed domains of PBuA dispersed in PVAc matrix; the domain sizes were increased with increased BuA content. Semicontinuous latex films were homogeneous in composition. Glass transition temperatures T_g determined from DMS and DSC indicated the presence of two, low and high, transition temperatures for batch latex films. The two temperatures approached the individual homopolymers, with increased PBuA content up to 51 mol %. Semicontinuous latex films showed only one single T_g. Tensile properties of the batch copolymer films showed a higher ultimate tensile strength, higher Young's modulus, and lower percent elongation to break compared to semicontinuous latex films. These differences were found to reflect the effect of mode of monomer addition during the emulsion copolymerization process on the particle morphology, and confirmed earlier data on bulk, colloidal, and surface properties of the same copolymer latexes.     

A polymer thin-film technique to study the micromorphology of core/shell latexes

A series of poly(styrene)/poly(styrene-co-acrylonitrile) core-shell latexes were synthesized by seeded emulsion polymerization. The dried latex was dissolved in toluene and then cast on the surface of water to form a very thin film (60–90 nm). Phase separation in the thin film was studied by transmission electron microscopy (TEM). Electron micrographs of these thin films yielded fine structure and interesting morphology that was unattainable by ultramicrotoming of the corresponding compression-molded specimens. Glass transition temperatures and percent grafted polystyrene were correlated with the TEM results. As grafting increases, mixing of the two phases improves, with the resulting T_g value being between the two T_g's of poly(styrene) and poly(styrene-co-acrylonitrile).     

Nanostructured latexes made by a sequential multistage emulsion polymerization

A series of linear and lightly crosslinked nanostructured latices was prepared by a sequential multistage semicontinuous emulsion polymerization process alternating styrene (S) and n‐butyl acrylate (BA) monomer feeds five times, that is ten stages, and vice versa, along with several control latices. Transmission electron micrographs of the RuO₄‐stained cross sections of nanostructured and copolymer latex particles and films showed that their particle morphologies were not very different from each other, but the nanostructured latex particles were transformed into a nanocomposite film containing both polystyrene (PS) and poly(n‐butyl acrylate) (PBA) nanodomains interconnected by their diffuse polymer mixtures (i.e. interlayers). The thermal mechanical behaviors of the nanostructured latex films showed broad but single T_gs slightly higher than those of their counterpart copolymer films. These single T_gs indicated that their major component phases were the diffuse interlayers and that they behaved like pseudopolymer alloys. The minimum film formation temperatures of nanostructured latices capped with PBA and PS, respectively, were 15 °C lower than and equal to those of their counterpart copolymer latices, but their T_gs were about 10 °C higher. Consequently, nanostructured latices enabled us to combine good film formation with high strengths for adhesives and coatings applications. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2826–2836, 2006     

Interface characterization in latex blend films by fluorescence energy transfer

Immiscible polymer blend films were formed by air drying aqueous dispersions containing mixtures of a high-T_g latex, poly(methyl methacrylate), and a film-forming low-T_g latex, poly(butyl methacrylate-co-butyl acrylate). Fluorescence energy transfer experiments were used to characterize the interfaces in these films, in which one component was labeled with a donor dye and the other with an acceptor. The quantum efficiency of energy transfer (Φ_ET) between the donors and acceptors is influenced by the interfacial contact area between the two polymer phases. As the amount of soft component in the blend is increased, Φ_ET approaches an asymptotic value, consistent with complete coverage of the hard polymer surface with soft polymer. This limiting extent of energy transfer is very sensitive to the total surface area in the film, with correspondingly more energy transfer at constant volume fraction for small hard particles. Some of the details of the energy transfer are revealed through a fluorescence lifetime distribution analysis. The presence of ionic surfactant (sodium dodecyl sulfate) in the dispersion from which the latex blend film is prepared reduces the cross-boundary energy transfer by 30%, which implies that in these films the surfactant decreases the interfacial contact. After annealing the surfactant-free blends above 100°C, we observe an increase in energy transfer, consistent with a broader interface between the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1115–1128, 1998     

A novel temperature‐step method to determine the glass transition temperature of ultrathin polymer films by liquid dewetting

A novel temperature‐step experimental method that extends the Bodiguel‐Fretigny liquid dewetting method of investigating polymer thin films is described and results presented from an investigation of thickness effects on the glass transition temperature (T_g) of ultrathin polystyrene (PS) films. Unlike most other methods of thin film investigation, this procedure promises a rapid screening tool to determine the overall profile of T_g versus film thickness for ultrathin polymer films using a limited number of samples. Similar to our prior observations and other literature data, with this new method obvious T_g depression was observed for PS thin films dewetting on both glycerol and an ionic liquid. The results for PS dewetting on the two different liquids are similar indicating only modest effects of the substrate on the T_g‐film thickness relationship. In both instances, the T_g depression is somewhat less than for similar PSs supported on silicon substrates reported in the literature. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1343–1349     

Impact of low‐molecular mass components (oligomers) on the glass transition in thin films of poly(methyl methacrylate)

Commercial polydisperse atactic poly(methyl methacrylate) (PMMA) exhibits a decreased glass transition temperature (T_g) when the film thickness is less than ～60 nm, whereas more model atactic PMMA shows an increased T_g in thin films supported on clean silicon wafers. NMR indicates no difference in tacticity, so the divergent thin film behavior appears related to the relative distribution of molecular mass. Extraction of some low molecular weight PMMA components from the commercial sample results in a significant modification of the thin film T_g compared with the initial PMMA fraction. The extracted sample exhibits initially a slight decrease in T_g as the film thickness is reduced below ～60 nm, but then T_g appears to increase for films thinner than 20 nm. These results illustrate the sensitivity of polymer thin film properties to low‐molecular mass components and could explain some of the contradictory reports on the T_g of polymer thin films that exist in the literature. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Carboxylic‐group distribution of carboxylated acrylate copolymer latexes with their properties in the presence of acrylic acid and monobutyl itaconate

A series of carboxylated acrylate copolymer latexes were prepared via two different emulsion polymerization technologies with different carboxylic‐group distribution and morphologies. The effects of the emulsifier, the initiator, and the carboxylic monomers [acrylic acid (AA) or monobutyl itaconate (MBI)] on the total conversion of the monomers and the properties of acrylate latexes and films have been investigated. The distribution of carboxylic groups (?COOH) measured by conductometric titration shows that the concentration of surface –COOH (C_s) and embedded –COOH (C_b) both increase with the increase of the amount of carboxylic monomers. For the latexes containing AA, –COOH tends to distribute on the surface of latex particles and in the aqueous phase, whereas –COOH tends to concentrate inside the core of latex particles for the latexes containing MBI. Transmission electron microscopy demonstrates that the latex particles are regular with narrow size distribution and have significant differences in morphologies when different carboxylic monomers and polymerization technologies were used. The stability of latex is satisfactory through the results of common stability and zeta potential tests. Moreover, the water absorption and contact angle experiment tests also revealed that the water resistance of the latex films is good. Copyright © 2011 John Wiley & Sons, Ltd.     

Film formation from nano‐sized polystyrene latex particles

This work reports on the steady state fluorescence (SSF) technique for studying film formation from surfactant‐free, nano‐sized polystyrene (PS) latex particles prepared via emulsion polymerization. The latex films were prepared from pyrene (P)‐labeled PS particles at room temperature and annealed at elevated temperatures in 5, 10, 15, 20 and 30 min time intervals above the glass transition temperature (T_g) of PS. During the annealing processes, the transparency of the film was improved considerably. Monomer and excimer fluorescence intensities, I_P and I_E respectively, from P were measured after each annealing step to monitor the stages of film formation. Evolution of transparency of the latex films was monitored by using photon transmission intensity, I_tr. Void closure and interdiffusion stages were modeled and related activation energies were determined and found to be 10.3 and 50.3 kJ mol⁻¹. Void closure temperatures, T_v, were determined from the minima of I_tr value. Copyright © 2005 John Wiley & Sons, Ltd.     

Structural relaxation of stacked ultrathin polystyrene films

The T_g depression and kinetic behavior of stacked polystyrene ultrathin films is investigated by differential scanning calorimetry (DSC) and compared with the behavior of bulk polystyrene. The fictive temperature (T_f) was measured as a function of cooling rate and as a function of aging time for aging temperatures below the nominal glass transition temperature (T_g). The stacked ultrathin films show enthalpy overshoots in DSC heating scans which are reduced in height but occur over a broader temperature range relative to the bulk response for a given change in fictive temperature. The cooling rate dependence of the limiting fictive temperature, T_f′, is also found to be higher for the stacked ultrathin film samples; the result is that the magnitude of the T_g depression between the ultrathin film sample and the bulk is inversely related to the cooling rate. We also find that the rate of physical aging of the stacked ultrathin films is comparable with the bulk when aging is performed at the same distance from T_g; however, when conducted at the same aging temperature, the ultrathin film samples show accelerated physical aging, that is, a shorter time is required to reach equilibrium for the thin films due to their depressed T_g values. The smaller distance from T_g also results in a reduced logarithmic aging rate for the thin films compared with the bulk, although this is not indicative of longer relaxation times. The DSC heating curves obtained as a function of cooling rate and aging history are modeled using the Tool-Narayanaswamy-Moynihan model of structural recovery; the stacked ultrathin film samples show lower β values than the bulk, consistent with a broader distribution of relaxation times. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2741–2753, 2008     

Chemical heterogeneity in emulsion copolymers of carboxylic monomers

Copolymer latices of butylacrylate (BA) with acrylic and methacrylic acid (AA and MAA) were prepared by batch type emulsion polymerization, and, for comparison, copolymers with identical monomer composition were prepared by batch type solution polymerization.The distribution of the carboxylic monomers in the latex particles and the serum was studied by density gradient and sedimentation experiments with the analytical ultracentrifuge. Dynamic mechanical measurements of films of these copolymers were used to determine the storage and loss moduli as a function of temperature. From these measurements the position and extension of the glass transition range on the temperature scale is obtained. For heterogeneous emulsion copolymers with two glass transition temperatures the distribution of the carboxylic monomer units in the different copolymer phases can be determined. Electron microscopy of ultra thin cross-sections of stained films gave further insight into the film morphology.The combination of the results obtained with the different methods gives rise to the following clues: In the BA/AA latices about 40% (by weight) of the total AA used in the recipe are found in the serum as a water soluble polymer, about 50% are found to increase the glass transition temperatureT _g of the bulk of the BA copolymer and, therefore, are thought to be incorporated into the interior of the latex particles, and the remaining 10% are, conclusively, located on the particle surface.In the BA/MAA latices no water soluble copolymer could be detected in the serum, about 90% of the MAA used is found in the bulk of the copolymer, and about 10% form a second hard phase on the surface of the latex particles.Dynamic mechanical measurements on the copolymer latex films show at least two phases with different glass transition temperatures: the bulk of the copolymer with a relatively low content of (M)AA units and a glass transition range at low temperatures, and a second (M)AA rich phase with a highT _g.The latter phase forms a honeycomb-like structure surrounding the packed latex particles. That results in a three-dimensional network of polymer with a highT _g extending throughout the latex film. In spite of the fact that this phase is built from a small fraction of the total copolymer only, it has a very pronounced influence on the performance behaviour of latex films.Dedicated to Professor Dr. R. Manecke on the occasion of his 70th birthday.     

Ellipsometric study of the glass transition and thermal expansion coefficients of thin polymer films

The glass transition (T_g) of thin polystyrene films (ca. 3000 A?) cast on silicon wafers was determined by a new technique. An ellipsometer was used to determine the refractive index and thickness of the polystyrene films. T_g was determined by measuring the temperature dependence of the refractive index. The change in thickness with temperature was used to calculate the linear and bulk thermal expansion coefficients of the material. A significant shift in T_g, possibly due to strains induced in the cooled films, was observed between heating and cooling for polystyrene films. © 1993 John Wiley & Sons, Inc.     

The effect of first-stage polymer Tg on the morphology and thermomechanical properties of structured polymer latex particles

A series of heterogeneous latexes having stage ratios of 40:60 between the first and second stage polymers were prepared by emulsion polymerization. The first-stage polymers were non-polar S-BuA with T_gs ranging from + 100 °C to + 20 °C and the second stage polymer was polar MMA–BuA–MAA having a T_g of 20 °C. The latex particle morphologies were studied using TEM and the thermomechanical properties of the resulting latex films were studied with DSC and DMA. Calculated diffusion rates for propagating species during the reactions were correlated to the observed morphologies and to the amount of interphase in the latex particles. To cite this article: O.J. Karlsson et al., C. R. Chimie 6 (2003).     

Effects of POSS nanoparticles on glass transition temperatures of ultrathin poly(t‐butyl acrylate) films and bulk blends

As a model system, thin films of trisilanolphenyl‐POSS (TPP) and two different number average molar mass (5 and 23 kg mol^?1) poly(t‐butyl acrylate) (PtBA) were prepared as blends by Langmuir–Blodgett film deposition. Films were characterized by ellipsometry. For comparison, bulk blends are prepared by solution casting and the samples are characterized via differential scanning calorimetry. The increase in T_g as a function of TPP content for bulk high and low molar mass samples are in the order of ～10 °C. Whereas bulk T_g shows comparable increases for both molar masses (～10 °C), the increase in surface T_g for higher molar mass PtBA is greater than for low molar mass (～22 °C vs. ～10 °C). Nonetheless, the total enhancement of T_g is complete by the time 20 wt % TPP is added without further benefit at higher nanofiller loads. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 175–182     

Novel method for the preparation of poly(urethane–imide)s and their properties

A polymer blend consisting of polyimide (PI) and polyurethane (PU) was prepared by means of a novel approach. PU prepolymer was prepared by the reaction of polyester polyol and 2,4-tolylenediisocyanate (2,4-TDI) and then end-capped with phenol. Poly(amide acid) was prepared from pyromellitic dianhydride (PMDA) and oxydianiline (ODA). A series of oligo(amide acid)s were also prepared by controlling the molar ratio of PMDA and ODA. The PU prepolymer and poly(amide acid) or oligo(amide acid) solution were blended at room temperature in various weight ratios. The cast films were obtained from the blend solution and treated at various temperatures. With the increase of polyurethane component, the films changed from plastic to brittle and then to elastic. The poly(urethane–imide) elastomers showed excellent mechanical properties and moderate thermal stability. The elongation of films with elasticity was more than 300%. The elongation set after the breaking of films was small. From the dynamic mechanical analysis, all the samples showed a glass transition temperature (T_g) at ca. −15°C, corresponding to T_g of the urethane component, suggesting that phase separation occurred between the two polymer components, irrespective of polyimide content. TGA and DSC studies indicated that the thermal degradation of poly(urethane–imide) was in the temperature range 250–270°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3745–3753, 1997     

Effect of sample preparation on the glass‐transition of thin polystyrene films

We have investigated the effect of sample preparation on the glass‐transition temperature (T_g) of thin films of polystyrene (PS). By preparing and measuring the glass‐transition temperature T_g of multilayered polymer films, we are able to assess the contribution of the spincoating process to the reduced T_g values often reported for thin PS films. We find that it is possible to determine a T_g even on the first heating cycle, and that by the third heating cycle (a total annealing time of 15 min at T = 393 K) the T_g value has reached a steady state. By comparing multilayered versus single layered films we find that the whole T_g depends only on the total film thickness, and not on the thickness of the individual layers. These results strongly suggest that the spincasting process does not contribute significantly to T_g reductions in thin polymer films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4503–4507, 2004     

Synthesis of Poly(n‐butyl acrylate/methyl methacrylate)/CNC Latex Nanocomposites via In Situ Emulsion Polymerization

Cellulose nanocrystals (CNCs) are renewable, nontoxic and naturally available organic nanoparticles derived from cellulosic resources such as cotton and wood pulp. Poly(n‐butyl acrylate‐co‐methyl methacrylate)/CNC latexes are successfully synthesized via in situ emulsion polymerization. The effect of CNC loading on overall conversion, polymer particle size, glass transition temperature (T_g), gel content, latex viscosity, and storage and loss moduli of dried latex are studied. While the effect of CNC content on overall conversion, polymer particle size, and T_g of the resulting latexes is negligible, significant increase in gel content, latex viscosity, and storage and loss moduli are observed.