Comparisons between conventional,ultrasound-assisted and microwave-assisted methods for extraction of anthraquinones from Heterophyllaea pustulata Hook f. (Rubiaceae)

This work reports a comparative study about extraction methods used to obtain anthraquinones (AQs) from stems and leaves of Heterophyllae pustulata Hook (Rubiáceae). One of the conventional procedures used to extract these metabolites from a vegetable matrix is by successive Soxhlet extractions with solvents of increasing polarity: starting with hexane to eliminate chlorophylls and fatty components, following by benzene and finally ethyl acetate. However, this technique shows a low extraction yield of total AQs, and consumes large quantities of solvent and time. Ultrasound-assisted extraction (UAE) and microwave-assisted extraction (MAE) have been investigated as alternative methods to extract these compounds, using the same sequence of solvents. It was found that UAE increases the extraction yield of total AQs and reduces the time and amount of solvent used. Nevertheless, the combination UAE with benzene, plus MAE with ethyl acetate at a constant power of 900 W showed the best results. A higher yield of total AQs was obtained in less time and using the same amount of solvent that UAE. The optimal conditions for this latter procedure were UAE with benzene at 50 °C during 60 min, followed by MAE at 900 W during 15 min using ethyl acetate as extraction solvent.     

Intensification of extraction of curcumin from Curcuma amada using ultrasound assisted approach: Effect of different operating parameters

Curcumin, a dietary phytochemical, has been extracted from rhizomes of Curcuma amada using ultrasound assisted extraction (UAE) and the results compared with the conventional extraction approach to establish the process intensification benefits. The effect of operating parameters such as type of solvent, extraction time, extraction temperature, solid to solvent ratio, particle size and ultrasonic power on the extraction yield have been investigated in details for the approach UAE. The maximum extraction yield as 72% was obtained in 1 h under optimized conditions of 35 °C temperature, solid to solvent ratio of 1:25, particle size of 0.09 mm, ultrasonic power of 250 W and ultrasound frequency of 22 kHz with ethanol as the solvent. The obtained yield was significantly higher as compared to the batch extraction where only about 62% yield was achieved in 8 h of treatment. Peleg’s model was used to describe the kinetics of UAE and the model showed a good agreement with the experimental results. Overall, ultrasound has been established to be a green process for extraction of curcumin with benefits of reduction in time as compared to batch extraction and the operating temperature as compared to Soxhlet extraction.     

Optimization of ultrasonic-assisted extraction of pomegranate (Punica granatum L.) seed oil

The effectiveness of ultrasonic-assisted extraction (UAE) of pomegranate seed oil (PSO) was evaluated using a variety of solvents. Petroleum ether was the most effective for oil extraction, followed by n-hexane, ethyl acetate, diethyl ether, acetone, and isopropanol. Several variables, such as ultrasonic power, extraction temperature, extraction time, and the ratio of solvent volume and seed weight (S/S ratio) were studied for optimization using response surface methodology (RSM). The highest oil yield, 25.11% (w/w), was obtained using petroleum ether under optimal conditions for ultrasonic power, extraction temperature, extraction time, and S/S ratio at 140 W, 40 °C, 36 min, and 10 ml/g, respectively. The PSO yield extracted by UAE was significantly higher than by using Soxhlet extraction (SE; 20.50%) and supercritical fluid extraction (SFE; 15.72%). The fatty acid compositions were significantly different among the PSO extracted by Soxhlet extraction, SFE, and UAE, with punicic acid (>65%) being the most dominant using UAE.     

Optimization of ultrasonic-assisted extraction (UAE) of betulin from white birch bark using response surface methodology

Betulin is an abundant naturally occurring triterpene, which makes it a potentially important raw material for a precursor of biologically active compounds. The objective of the current study was to determine the optimum UAE conditions for betulin from B. papyfera bark. The optimum conditions were evaluated with fractional factorial design and optimized using response surface methodology. High yields of betulin were observed from white birch bark by UAE technology. The solvent concentration and the ratio of material to solvent were the most significant parameters on betulin extraction as evaluated through FFD. The extraction conditions were further investigated with central composite design. The fitted second-order model revealed that the optimal conditions consisted of 98% ethonal concentration, 1:42 the ratio of white birch bark to solvent, extraction temperature 50 °C, ultrasonic frequency 5 kHz and extraction time 3 h. Under the optimized condition, the maximum productivity of betulin predicted is 23.17%. The extraction productivity and purity of betulin under the optimized extraction conditions were great higher than that of the non-optimized condition. The present study demonstrates that ultrasound is a great efficiency tool for the fast extraction of betulin from white birch bark.     

Optimization of ultrasound-assisted extraction of total monomeric anthocyanin (TMA) and total phenolic content (TPC) from eggplant (Solanum melongena L.) peel

The present study describes the extraction of total monomeric anthocyanin (TMA) and total phenolic content (TPC) from eggplant peel using ultrasonic treatments and methanol and 2-propanol as extraction solvents. The extraction yields were optimized by varying the solvent concentration, ultrasonic frequency, temperature and time of ultrasonic treatment. Box–Behnken design was used to investigate the effect of process variables on the ultrasound-assisted extraction. The results showed that for TPC extraction the optimal condition were obtained with a methanol concentration of 76.6%, 33.88 kHz ultrasonic frequency, a temperature of 69.4 °C and 57.5 min extraction time. For TMA the optimal condition were the following: 54.4% methanol concentration, 37 kHz, 55.1 °C and process time of 44.85 min.     

Effects of various factors of ultrasonic treatment on the extraction recovery of drugs from fish tissues

In the present research, a combined extraction method of ultrasound-assisted extraction (UAE) in conjunction with solid phase extraction (SPE) was applied to isolation and enrichment of selected drugs (metoprolol, ticlopidine, propranolol, carbamazepine, naproxen, acenocumarol, diclofenac, ibuprofen) from fish tissues. The extracted analytes were separated and determined by ultra-high performance liquid chromatography with UV detection (UHPLC–UV) technique. The selectivity of the developed UHPLC–UV method was confirmed by comparison with ultra-high performance liquid chromatography–tandem mass spectrometry (UHPLC–MS/MS) analysis.The important parameters, such as composition of type and pH of extraction solvent, solid/liquid rate volume of extraction solvent and number of extraction cycles were studied. The ultrasonic parameters, such as time, power and temperature of the process were optimized by using a half-fraction factorial central composite design (CCD). The mixture of 10 mL of methanol and 7 mL of water (pH 2.2) (three times) was chosen for the extraction of selected drug from fish tissues. The results showed that the highest recoveries of analytes were obtained with an extraction temperature of 40 °C, ultrasonic power of 300 W, extraction time of 30 min.Under the optimal conditions, the linearity of method was 0.12–5.00 μg/g. The determination coefficients (R²) were from 0.979 to 0.998. The limits of detection (LODs) and limits of quantification (LOQs) for the extracted compounds were 0.04–0.17 μg/g and 0.12–0.50 μg/g, respectively. The recoveries were between 85.5% and 115.8%.     

Development and validation of an efficient ultrasound assisted extraction of phenolic compounds from flax (Linum usitatissimum L.) seeds

Flaxseed accumulates in its seedcoat a macromolecular complex composed of lignan (secoisolariciresinol diglucoside, SDG), flavonol (herbacetin diglucoside, HDG) and hydroxycinnamic acids (p-couramic, caffeic and ferulic acid glucosides). Their antioxidant and/or cancer chemopreventive properties support their interest in human health and therefore, the demand for their extraction. In the present study, ultrasound-assisted extraction (UAE) of flaxseed phenolic compounds was investigated. Scanning Electron Microscopy imaging and histochemical analysis revealed the deep alteration of the seedcoat ultrastructure and the release of the mucilage following ultrasound treatment. Therefore, this method was found to be very efficient for the reduction of mucilage entrapment of flaxseed phenolics. The optimal conditions for UAE phenolic compounds extraction from flaxseeds were found to be: water as solvent supplemented with 0.2 N of sodium hydroxide for alkaline hydrolysis of the SDG–HMG complex, an extraction time of 60 min at a temperature of 25 °C and an ultrasound frequency of 30 kHz. Under these optimized and validated conditions, highest yields of SDG, HDG and hydroxycinnamic acid glucosides were detected in comparison to other published methods. Therefore, the procedure presented herein is a valuable method for efficient extraction and quantification of the main flaxseed phenolics. Moreover, this UAE is of particular interest within the context of green chemistry in terms of reducing energy consumption and valuation of flaxseed cakes as by-products resulting from the production of flax oil.     

Ultrasound assisted extraction of β-carotene from Spirulina platensis

This paper illustrates the Ultrasound Assisted Extraction (UAE) of β-carotene from Spirulina platensis. Various parameters such as extraction time, solvent type, biomass to solvent ratio, temperature, electrical acoustic intensity, length of the probe tip dipped into the solvent, duty cycle and pre treatment effect were explored for the extraction of β-carotene. From economic point of view, the optimal conditions for the extraction of β-carotene from Spirulina were 1.5 g Spirulina (2 min pre soaked in methanol) in 50 ml n-heptane at 30 °C temperature, 167 W/cm² electrical acoustic intensity and 61.5% duty cycle for 8 min with probe tip length of 0.5 cm dipped into the extracting solvent from the surface. The maximum extraction achieved under the above mentioned optimum parameters was 47.10%. The pre-treatment time showed a promising effect on the yield as pre-treating the biomass with methanol for 2 min before ultrasonication showed 12 times increase in extraction yield of β-carotene.     

Effect of ultrasound on the extraction of total anthocyanins from Purple Majesty potato

This study examined anthocyanin extraction using the application of ultrasound to raw freeze dried, microwaved and raw sliced Purple Majesty potato, a new pigmented potato variety rich in anthocyanins. A 20 kHz probe was used for the sonication at 3 different amplitudes (30%, 50% and 70%) and ethanol in water at different ratios (50:50 and 70:30 v/v) was used for the extraction. Anthocyanin extraction from raw freeze dried purple potato was optimal at an ethanol:water ratio (70:30; v/v) after 5 min of ultrasonication, while the least amount of anthocyanins was extracted from raw sliced potatoes. The application of microwaves (as a pre-treatment) before the UAE resulted in an increase in the amount of anthocyanins extracted and a decrease in the amount of solvent used. Analysis of variance showed that potato form, ultrasonication time, ultrasonication amplitude and solvent ratio as well as two and three way interactions between some of these factors had a very significant effect (p < 0.000) on the amount of anthocyanins extracted.     

Optimisation of ultrasound assisted extraction of phenolic compounds from Sparganii rhizoma with response surface methodology

The present study reports on the extraction of phenolic compounds from sparganii rhizome. Box–Behnken Design (BBD), a widely used form of response surface methodology (RSM), was used to investigate the effect of process variables on the ultrasound-assisted extraction (UAE). Three independent variables including ethanol concentration (%), extraction time (min) and solvent-to-material ratio (mL/g) were studied. The results showed that the optimal UAE condition was obtained with an ethanol concentration of 75.3%, an extraction time of 40 min and a solvent-to-material ratio of 19.21 mL/g for total phenols, and an ethanol concentration of 80%, an extraction time of 33.54 min and solvent-to-material ratio of 22.72 mL/g for combination of ρ-hydroxybenzaldehyde, ρ-coumaric acid, vanillic acid, ferulic acid, rutin and kaempferol. The experimental values under optimal conditions were in good consistent with the predicted values, which suggested UAE is more efficient process as compared to solvent extraction.     

Kinetic improvement of olive leaves’ bioactive compounds extraction by using power ultrasound in a wide temperature range

In this study, the effect of temperature and ultrasonic application on extraction kinetics of polyphenols from dried olive leaf was investigated. Conventional (CVE) and ultrasonic-assisted extraction (UAE) were performed at 10, 20, 30, 50 and 70 °C using water as solvent. Extracts were characterized by measuring the total phenolic content, the antioxidant capacity and the oleuropein content (HPLC–DAD/MS–MS). Moreover, Naik’s model was used to mathematically describe the extraction kinetics. The experimental results showed that phenolic extraction was faster in UAE (ultrasonic-assisted extraction) than in CVE (conventional extraction), being extraction kinetics satisfactorily described using Naik model (include VAR > 98%). Besides, the total phenolic content, the antioxidant capacity and the oleuropein content were significantly (p < 0.05) improved by increasing the temperature in both CVE and UAE. Oleuropein content reached 6.57 ± 0.18 being extracted approximately 88% in the first minute for UAE experiments.     

Effects of various factors of ultrasonic treatment on the extraction yield of all-trans-lycopene from red grapefruit (Citrus paradise Macf.)

The effects of various factors, including the extraction time, temperature, solvent/material ratio, the ultrasonic intensity and duty cycle of ultrasonic irradiation on the extraction yield of all-trans-lycopene from red grapefruit by ultrasound-assisted extraction (UAE) were investigated. In comparison with conventional solvent extraction (CSE), UAE showed a pronounced greater extraction yield and reduced extraction time effectively with a peak value at 30 min. The extraction yield was significantly influenced by temperature and the optimum condition was 30 °C. The extraction yield increased with increasing of solvent/material ratio until equilibrium was arrived at the optimal ratio of 3:1 (mL/g). The extraction yield increased first and then decreased with an increase in ultrasonic intensity. The extraction yield of UAE increased with the increase of duty cycle, whereas pulsed ultrasound with proper intervals was more efficient than continuous ultrasonication. The degradation via isomerisation of all-trans-lycopene under ultrasonic treatment was also observed with the formation of 9,13′-di-cis-, 9,13-di-cis-, 15-cis-, 13-cis- and 9-cis-lycopene isomers which were tentatively identified by HPLC-PAD.     

Effect of acoustic frequency and power density on the aqueous ultrasonic-assisted extraction of grape pomace (Vitis vinifera L.) – A response surface approach

Aqueous ultrasound-assisted extraction (UAE) of grape pomace was investigated by Response Surface Methodology (RSM) to evaluate the effect of acoustic frequency (40, 80, 120 kHz), ultrasonic power density (50, 100, 150 W/L) and extraction time (5, 15, 25 min) on total phenolics, total flavonols and antioxidant capacity. All the process variables showed a significant effect on the aqueous UAE of grape pomace (p < 0.05). The Box–Behnken Design (BBD) generated satisfactory mathematical models which accurately explain the behavior of the system; allowing to predict both the extraction yield of phenolic and flavonol compounds, and also the antioxidant capacity of the grape pomace extracts. The optimal UAE conditions for all response factors were a frequency of 40 kHz, a power density of 150 W/L and 25 min of extraction time. Under these conditions, the aqueous UAE would achieve a maximum of 32.31 mg GA/100 g fw for total phenolics and 2.04 mg quercetin/100 g fw for total flavonols. Regarding the antioxidant capacity, the maximum predicted values were 53.47 and 43.66 mg Trolox/100 g fw for CUPRAC and FRAP assays, respectively. When comparing with organic UAE, in the present research, from 12% to 38% of total phenolic bibliographic values were obtained, but using only water as the extraction solvent, and applying lower temperatures and shorter extraction times. To the best of the authors’ knowledge, no studies specifically addressing the optimization of both acoustic frequency and power density during aqueous-UAE of plant materials have been previously published.     

Bio-refinery of orange peels waste: A new concept based on integrated green and solvent free extraction processes using ultrasound and microwave techniques to obtain essential oil,polyphenols and pectin

In this study, extraction of essential oil, polyphenols and pectin from orange peel has been optimized using microwave and ultrasound technology without adding any solvent but only “in situ” water which was recycled and used as solvent. The essential oil extraction performed by Microwave Hydrodiffusion and Gravity (MHG) was optimized and compared to steam distillation extraction (SD). No significant changes in yield were noticed: 4.22 ± 0.03% and 4.16 ± 0.05% for MHG and SD, respectively. After extraction of essential oil, residual water of plant obtained after MHG extraction was used as solvent for polyphenols and pectin extraction from MHG residues. Polyphenols extraction was performed by ultrasound-assisted extraction (UAE) and conventional extraction (CE). Response surface methodology (RSM) using central composite designs (CCD) approach was launched to investigate the influence of process variables on the ultrasound-assisted extraction (UAE). The statistical analysis revealed that the optimized conditions of ultrasound power and temperature were 0.956 W/cm² and 59.83 °C giving a polyphenol yield of 50.02 mg GA/100 g dm. Compared with the conventional extraction (CE), the UAE gave an increase of 30% in TPC yield. Pectin was extracted by conventional and microwave assisted extraction. This technique gives a maximal yield of 24.2% for microwave power of 500 W in only 3 min whereas conventional extraction gives 18.32% in 120 min. Combination of microwave, ultrasound and the recycled “in situ” water of citrus peels allow us to obtain high added values compounds in shorter time and managed to make a closed loop using only natural resources provided by the plant which makes the whole process intensified in term of time and energy saving, cleanliness and reduced waste water.     

Kinetics of ultrasound-assisted extraction of antioxidant polyphenols from food by-products: Extraction and energy consumption optimization

Ultrasound-assisted extraction (UAE) of antioxidant polyphenols from chicory grounds was studied in order to propose a suitable valorization of this food industry by-product. The main parameters influencing the extraction process were identified. A new mathematical model for multi-criteria optimization of UAE was proposed. This kinetic model permitted the following and the prediction of the yield of extracted polyphenols, the antioxidant activity of the obtained extracts and the energy consumption during the extraction process in wide ranges of temperature (20–60 °C), ethanol content in the solvent (0–60% (vol.) in ethanol–water mixtures) and ultrasound power (0–100 W). After experimental validation of the model, several simulations at different technological restrictions were performed to illustrate the potentiality of the model to find the optimal conditions for obtaining a given yield within minimal process duration or with minimal energy consumption. The advantage of ultrasound assistance was clearly demonstrated both for the reduction of extraction duration and for the reduction of energy consumption.     

Ultrasonic extraction of steroidal alkaloids from potato peel waste

Potato processors produce large volumes of waste in the form of potato peel which is either discarded or sold at a low price. Potato peel waste is a potential source of steroidal alkaloids which are biologically active secondary metabolites which could serve as precursors to agents with apoptotic, chemopreventive and anti-inflammatory properties. The present study investigated the relative efficacy of ultrasound assisted extraction (UAE) and solid liquid extraction (SLE) both using methanol, to extract steroidal alkaloids from potato peel waste and identified optimal conditions for UAE of α-solanine, α-chaconine, solanidine and demissidine. Using response surface methodology optimal UAE conditions were identified as an amplitude of 61 μm and an extraction time of 17 min which resulted the recovery of 1102 μg steroidal alkaloids/g dried potato peel (DPP). In contrast, SLE yielded 710.51 glycoalkaloid μg/g DPP. Recoveries of individual glycoalkoids using UAE yielded 273, 542.7, 231 and 55.3 μg/g DPP for α-solanine, α-chaconine, solanidine and demissidine respectively. Whereas for SLE yields were 180.3, 337.6, 160.2 and 32.4 μg/g DPP for α-solanine, α-chaconine, solanidine and demissidine respectively. The predicted values from the developed second order quadratic polynomial equation were in close agreement with the experimental values with low average mean deviation (E < 5%) values. Predicted models were highly significant (p < 0.05) for all parameters studied. This study indicates that UAE has strong potential as an extraction method for steroidal alkaloids from potato peel waste.     

Ultrasound-assisted extraction of polyphenols from native plants in the Mexican desert

Several plants that are rich in polyphenolic compounds and exhibit biological properties are grown in the desert region of Mexico under extreme climate conditions. These compounds have been recovered by classic methodologies in these plants using organic solvents. However, little information is available regarding the use of alternative extraction technologies, such as ultrasound. In this paper, ultrasound-assisted extraction (UAE) parameters, such as the liquid:solid ratio, solvent concentration and extraction time, were studied using response surface methodology (RSM) for the extraction of polyphenols from desert plants including Jatropha dioica, Flourensia cernua, Turnera diffusa and Eucalyptus camaldulensis. Key process variables (i.e., liquid:solid ratio and ethanol concentration) exert the greatest influence on the extraction of all of the phenolic compounds (TPC) in the studied plants. The best conditions for the extraction of TPC involved an extraction time of 40 min, an ethanol concentration of 35% and a liquid:solid ratio ranging from 8 to 12 ml g⁻¹ depending on the plant. The highest antioxidant activity was obtained in the E. camaldulensis extracts. The results indicated the ability of UAE to obtain polyphenolic antioxidant preparations from desert plants.     

Aqueous ionic liquid based ultrasonic assisted extraction of four acetophenones from the Chinese medicinal plant Cynanchum bungei Decne

In this study, an aqueous ionic liquid based ultrasonic assisted extraction (ILUAE) method for the extraction of the four acetophenones, namely 4-hydroxyacetophenone (1), 2,5-dihydroxyacetophenone (2), baishouwubenzophenone (3) and 2,4-dihydroxyacetophenone (4) from the Chinese medicinal plant Cynanchum bungei was developed. Three kinds of aqueous l-alkyl-3-methylimidazolium ionic liquids with different anion and alkyl chain were investigated. The results indicated that ionic liquids (ILs) showed remarkable effects on the extraction efficiency of acetophenones. In addition, the ILUAE, including several ultrasonic parameters, such as the ILs concentration, solvent to solid ratio, power, particle size, temperature, and extraction time have been optimized. Under these optimal conditions (e.g., with 0.6 M [C₄MIM]BF₄, solvent to solid ratio of 35:1, power of 175 W, particle size of 60–80 mesh, temperature of 25 °C and time of 50 min), this approach gained the highest extraction yields of four acetophenones 286.15, 21.65, 632.58 and 205.38 μg/g, respectively. The proposed approach has been evaluated by comparison with the conventional heat-reflux extraction (HRE) and regular UAE. The results indicated that ILUAE is an alternative method for extracting acetophenones from C. bungei.     

Effect of ultrasonic treatment on the polyphenol content and antioxidant capacity of extract from defatted hemp,flax and canola seed cakes

The effectiveness of ultrasonic extraction of phenolics and flavonoids from defatted hemp, flax and canola seed cakes was compared to the conventional extraction method. Ultrasonic treatment at room temperature showed increased polyphenol extraction yield and antioxidant capacity by two-fold over the conventional extraction method. Different combinations of ultrasonic treatment parameters consisting of solvent volume (25, 50, 75 and 100 mL), extraction time (20, 30 and 40 min) and temperature (40, 50, 60 and 70 °C) were selected for polyphenol extractions from the seed cakes. The chosen parameters had a significant effect (p < 0.05) on the polyphenol extraction yield and subsequent antioxidant capacity from the seed cakes. Application of heat during ultrasonic extraction yielded higher polyphenol content in extracts compared to the non-heated extraction. From an orthogonal design test, the best combination of parameters was 50 mL of solvent volume, 20 min of extraction time and 70 °C of ultrasonic temperature.     

Green ultrasound-assisted extraction of carotenoids based on the bio-refinery concept using sunflower oil as an alternative solvent

A green, inexpensive and easy-to-use method for carotenoids extraction from fresh carrots assisted by ultrasound was designed in this work. Sunflower oil was applied as a substitute to organic solvents in this green ultrasound-assisted extraction (UAE): a process which is in line with green extraction and bio-refinery concepts. The processing procedure of this original UAE was first compared with conventional solvent extraction (CSE) using hexane as solvent. Moreover, the UAE optimal conditions for the subsequent comparison were optimized using response surface methodology (RSM) and ultra performance liquid chromatography – diode array detector – mass spectroscopy (UPLC–DAD–MS). The results showed that the UAE using sunflower as solvent has obtained its highest β-carotene yield (334.75 mg/l) in 20 min only, while CSE using hexane as solvent obtained a similar yield (321.35 mg/l) in 60 min. The green UAE performed under optimal extraction conditions (carrot to oil ratio of 2:10, ultrasonic intensity of 22.5 W cm^?2, temperature of 40 °C and sonication time of 20 min) gave the best yield of β-carotene.