Ultrasound assisted extraction of β-carotene from Spirulina platensis

This paper illustrates the Ultrasound Assisted Extraction (UAE) of β-carotene from Spirulina platensis. Various parameters such as extraction time, solvent type, biomass to solvent ratio, temperature, electrical acoustic intensity, length of the probe tip dipped into the solvent, duty cycle and pre treatment effect were explored for the extraction of β-carotene. From economic point of view, the optimal conditions for the extraction of β-carotene from Spirulina were 1.5 g Spirulina (2 min pre soaked in methanol) in 50 ml n-heptane at 30 °C temperature, 167 W/cm² electrical acoustic intensity and 61.5% duty cycle for 8 min with probe tip length of 0.5 cm dipped into the extracting solvent from the surface. The maximum extraction achieved under the above mentioned optimum parameters was 47.10%. The pre-treatment time showed a promising effect on the yield as pre-treating the biomass with methanol for 2 min before ultrasonication showed 12 times increase in extraction yield of β-carotene.     

Comparisons between conventional,ultrasound-assisted and microwave-assisted methods for extraction of anthraquinones from Heterophyllaea pustulata Hook f. (Rubiaceae)

This work reports a comparative study about extraction methods used to obtain anthraquinones (AQs) from stems and leaves of Heterophyllae pustulata Hook (Rubiáceae). One of the conventional procedures used to extract these metabolites from a vegetable matrix is by successive Soxhlet extractions with solvents of increasing polarity: starting with hexane to eliminate chlorophylls and fatty components, following by benzene and finally ethyl acetate. However, this technique shows a low extraction yield of total AQs, and consumes large quantities of solvent and time. Ultrasound-assisted extraction (UAE) and microwave-assisted extraction (MAE) have been investigated as alternative methods to extract these compounds, using the same sequence of solvents. It was found that UAE increases the extraction yield of total AQs and reduces the time and amount of solvent used. Nevertheless, the combination UAE with benzene, plus MAE with ethyl acetate at a constant power of 900 W showed the best results. A higher yield of total AQs was obtained in less time and using the same amount of solvent that UAE. The optimal conditions for this latter procedure were UAE with benzene at 50 °C during 60 min, followed by MAE at 900 W during 15 min using ethyl acetate as extraction solvent.     

Optimization of ultrasonic-assisted extraction of pomegranate (Punica granatum L.) seed oil

The effectiveness of ultrasonic-assisted extraction (UAE) of pomegranate seed oil (PSO) was evaluated using a variety of solvents. Petroleum ether was the most effective for oil extraction, followed by n-hexane, ethyl acetate, diethyl ether, acetone, and isopropanol. Several variables, such as ultrasonic power, extraction temperature, extraction time, and the ratio of solvent volume and seed weight (S/S ratio) were studied for optimization using response surface methodology (RSM). The highest oil yield, 25.11% (w/w), was obtained using petroleum ether under optimal conditions for ultrasonic power, extraction temperature, extraction time, and S/S ratio at 140 W, 40 °C, 36 min, and 10 ml/g, respectively. The PSO yield extracted by UAE was significantly higher than by using Soxhlet extraction (SE; 20.50%) and supercritical fluid extraction (SFE; 15.72%). The fatty acid compositions were significantly different among the PSO extracted by Soxhlet extraction, SFE, and UAE, with punicic acid (>65%) being the most dominant using UAE.     

Bio-refinery of orange peels waste: A new concept based on integrated green and solvent free extraction processes using ultrasound and microwave techniques to obtain essential oil,polyphenols and pectin

In this study, extraction of essential oil, polyphenols and pectin from orange peel has been optimized using microwave and ultrasound technology without adding any solvent but only “in situ” water which was recycled and used as solvent. The essential oil extraction performed by Microwave Hydrodiffusion and Gravity (MHG) was optimized and compared to steam distillation extraction (SD). No significant changes in yield were noticed: 4.22 ± 0.03% and 4.16 ± 0.05% for MHG and SD, respectively. After extraction of essential oil, residual water of plant obtained after MHG extraction was used as solvent for polyphenols and pectin extraction from MHG residues. Polyphenols extraction was performed by ultrasound-assisted extraction (UAE) and conventional extraction (CE). Response surface methodology (RSM) using central composite designs (CCD) approach was launched to investigate the influence of process variables on the ultrasound-assisted extraction (UAE). The statistical analysis revealed that the optimized conditions of ultrasound power and temperature were 0.956 W/cm² and 59.83 °C giving a polyphenol yield of 50.02 mg GA/100 g dm. Compared with the conventional extraction (CE), the UAE gave an increase of 30% in TPC yield. Pectin was extracted by conventional and microwave assisted extraction. This technique gives a maximal yield of 24.2% for microwave power of 500 W in only 3 min whereas conventional extraction gives 18.32% in 120 min. Combination of microwave, ultrasound and the recycled “in situ” water of citrus peels allow us to obtain high added values compounds in shorter time and managed to make a closed loop using only natural resources provided by the plant which makes the whole process intensified in term of time and energy saving, cleanliness and reduced waste water.     

Effects of various factors of ultrasonic treatment on the extraction yield of all-trans-lycopene from red grapefruit (Citrus paradise Macf.)

The effects of various factors, including the extraction time, temperature, solvent/material ratio, the ultrasonic intensity and duty cycle of ultrasonic irradiation on the extraction yield of all-trans-lycopene from red grapefruit by ultrasound-assisted extraction (UAE) were investigated. In comparison with conventional solvent extraction (CSE), UAE showed a pronounced greater extraction yield and reduced extraction time effectively with a peak value at 30 min. The extraction yield was significantly influenced by temperature and the optimum condition was 30 °C. The extraction yield increased with increasing of solvent/material ratio until equilibrium was arrived at the optimal ratio of 3:1 (mL/g). The extraction yield increased first and then decreased with an increase in ultrasonic intensity. The extraction yield of UAE increased with the increase of duty cycle, whereas pulsed ultrasound with proper intervals was more efficient than continuous ultrasonication. The degradation via isomerisation of all-trans-lycopene under ultrasonic treatment was also observed with the formation of 9,13′-di-cis-, 9,13-di-cis-, 15-cis-, 13-cis- and 9-cis-lycopene isomers which were tentatively identified by HPLC-PAD.     

Intensification of extraction of curcumin from Curcuma amada using ultrasound assisted approach: Effect of different operating parameters

Curcumin, a dietary phytochemical, has been extracted from rhizomes of Curcuma amada using ultrasound assisted extraction (UAE) and the results compared with the conventional extraction approach to establish the process intensification benefits. The effect of operating parameters such as type of solvent, extraction time, extraction temperature, solid to solvent ratio, particle size and ultrasonic power on the extraction yield have been investigated in details for the approach UAE. The maximum extraction yield as 72% was obtained in 1 h under optimized conditions of 35 °C temperature, solid to solvent ratio of 1:25, particle size of 0.09 mm, ultrasonic power of 250 W and ultrasound frequency of 22 kHz with ethanol as the solvent. The obtained yield was significantly higher as compared to the batch extraction where only about 62% yield was achieved in 8 h of treatment. Peleg’s model was used to describe the kinetics of UAE and the model showed a good agreement with the experimental results. Overall, ultrasound has been established to be a green process for extraction of curcumin with benefits of reduction in time as compared to batch extraction and the operating temperature as compared to Soxhlet extraction.     

Effect of ultrasound and green solvents addition on the oil extraction efficiency from rapeseed flakes

The current procedure of rapeseed oil extraction is based on a first extraction step by pressing followed by a second extraction step with hexane. This solvent being toxic for the users, the consumers and the environment, its use could be forbidden within the coming years. Stimulated by a stringent regulation, the research activity for the replacement of toxic solvents shows a significant development. The aim of this study was to select alternative solvent to hexane such as ethanol or isopropanol, and, to adjust the oil extraction process by developing an ultrasound assisted method. The objective was to reach a comparable efficiency but also to enhance the oil quality. When applied to isopropanol, the ultrasound assisted extraction method has shown promising results, and comparable to those obtained with hexane (oil yield of 80% for hexane and 79% for isopropanol at optimum extraction conditions (20 min of ultrasound pretreatment followed by 2 h of additional solid/liquid extraction)). Conversely, in studied conditions, ethanol did not seem to be an appropriate alternative solvent to hexane as the extraction yields obtained by using this solvent were quite low.     

Recovery of β-carotene from pumpkin using switchable natural deep eutectic solvents

The aim of the present research was to develop green and sustainable extraction procedure for β-carotene recovery from pumpkin. A series of hydrophobic natural deep eutectic solvents (NADESs) based on fatty acids were prepared to establish high extraction efficiency of β-carotene and to increase stability of extracted carotenoids from the pumpkin. To intensify extraction process, NADES composed of C8 and C10 fatty acids (3:1) was selected and coupled with ultrasound assisted extraction. Response surface methodology and artificial neural network model (ANN) model was adopted to analyze significance of extraction parameters demonstrating high prediction levels of the β-carotene yield, experimentally confirming the maximum β-carotene content of 151.41 µg/mL at the optimal process condition. Extracted carotenoids in the optimal NADES extract have shown high stability during the storing period of 180 days. A switchable-hydrophilicity eutectic solvent system has been introduced as a successful way to recover extracted carotenoids from the NADES solvent. It was capable of precipitating 90% of carotenoids present in the extract. The proposed procedure is simple, easily scalable and has minimal impact on operators and the environment.     

Effect of acoustic frequency and power density on the aqueous ultrasonic-assisted extraction of grape pomace (Vitis vinifera L.) – A response surface approach

Aqueous ultrasound-assisted extraction (UAE) of grape pomace was investigated by Response Surface Methodology (RSM) to evaluate the effect of acoustic frequency (40, 80, 120 kHz), ultrasonic power density (50, 100, 150 W/L) and extraction time (5, 15, 25 min) on total phenolics, total flavonols and antioxidant capacity. All the process variables showed a significant effect on the aqueous UAE of grape pomace (p < 0.05). The Box–Behnken Design (BBD) generated satisfactory mathematical models which accurately explain the behavior of the system; allowing to predict both the extraction yield of phenolic and flavonol compounds, and also the antioxidant capacity of the grape pomace extracts. The optimal UAE conditions for all response factors were a frequency of 40 kHz, a power density of 150 W/L and 25 min of extraction time. Under these conditions, the aqueous UAE would achieve a maximum of 32.31 mg GA/100 g fw for total phenolics and 2.04 mg quercetin/100 g fw for total flavonols. Regarding the antioxidant capacity, the maximum predicted values were 53.47 and 43.66 mg Trolox/100 g fw for CUPRAC and FRAP assays, respectively. When comparing with organic UAE, in the present research, from 12% to 38% of total phenolic bibliographic values were obtained, but using only water as the extraction solvent, and applying lower temperatures and shorter extraction times. To the best of the authors’ knowledge, no studies specifically addressing the optimization of both acoustic frequency and power density during aqueous-UAE of plant materials have been previously published.     

Optimisation of ultrasound assisted extraction of phenolic compounds from Sparganii rhizoma with response surface methodology

The present study reports on the extraction of phenolic compounds from sparganii rhizome. Box–Behnken Design (BBD), a widely used form of response surface methodology (RSM), was used to investigate the effect of process variables on the ultrasound-assisted extraction (UAE). Three independent variables including ethanol concentration (%), extraction time (min) and solvent-to-material ratio (mL/g) were studied. The results showed that the optimal UAE condition was obtained with an ethanol concentration of 75.3%, an extraction time of 40 min and a solvent-to-material ratio of 19.21 mL/g for total phenols, and an ethanol concentration of 80%, an extraction time of 33.54 min and solvent-to-material ratio of 22.72 mL/g for combination of ρ-hydroxybenzaldehyde, ρ-coumaric acid, vanillic acid, ferulic acid, rutin and kaempferol. The experimental values under optimal conditions were in good consistent with the predicted values, which suggested UAE is more efficient process as compared to solvent extraction.     

Development and validation of an efficient ultrasound assisted extraction of phenolic compounds from flax (Linum usitatissimum L.) seeds

Flaxseed accumulates in its seedcoat a macromolecular complex composed of lignan (secoisolariciresinol diglucoside, SDG), flavonol (herbacetin diglucoside, HDG) and hydroxycinnamic acids (p-couramic, caffeic and ferulic acid glucosides). Their antioxidant and/or cancer chemopreventive properties support their interest in human health and therefore, the demand for their extraction. In the present study, ultrasound-assisted extraction (UAE) of flaxseed phenolic compounds was investigated. Scanning Electron Microscopy imaging and histochemical analysis revealed the deep alteration of the seedcoat ultrastructure and the release of the mucilage following ultrasound treatment. Therefore, this method was found to be very efficient for the reduction of mucilage entrapment of flaxseed phenolics. The optimal conditions for UAE phenolic compounds extraction from flaxseeds were found to be: water as solvent supplemented with 0.2 N of sodium hydroxide for alkaline hydrolysis of the SDG–HMG complex, an extraction time of 60 min at a temperature of 25 °C and an ultrasound frequency of 30 kHz. Under these optimized and validated conditions, highest yields of SDG, HDG and hydroxycinnamic acid glucosides were detected in comparison to other published methods. Therefore, the procedure presented herein is a valuable method for efficient extraction and quantification of the main flaxseed phenolics. Moreover, this UAE is of particular interest within the context of green chemistry in terms of reducing energy consumption and valuation of flaxseed cakes as by-products resulting from the production of flax oil.     

Kinetic improvement of olive leaves’ bioactive compounds extraction by using power ultrasound in a wide temperature range

In this study, the effect of temperature and ultrasonic application on extraction kinetics of polyphenols from dried olive leaf was investigated. Conventional (CVE) and ultrasonic-assisted extraction (UAE) were performed at 10, 20, 30, 50 and 70 °C using water as solvent. Extracts were characterized by measuring the total phenolic content, the antioxidant capacity and the oleuropein content (HPLC–DAD/MS–MS). Moreover, Naik’s model was used to mathematically describe the extraction kinetics. The experimental results showed that phenolic extraction was faster in UAE (ultrasonic-assisted extraction) than in CVE (conventional extraction), being extraction kinetics satisfactorily described using Naik model (include VAR > 98%). Besides, the total phenolic content, the antioxidant capacity and the oleuropein content were significantly (p < 0.05) improved by increasing the temperature in both CVE and UAE. Oleuropein content reached 6.57 ± 0.18 being extracted approximately 88% in the first minute for UAE experiments.     

A possible general mechanism for ultrasound-assisted extraction (UAE) suggested from the results of UAE of chlorogenic acid from Cynara scolymus L. (artichoke) leaves

The use of ultrasound-assisted extraction (UAE) for the extraction of chlorogenic acid (CA) from Cynara scolymus L., (artichoke) leaves using 80% methanol at room temperature over 15 min gave a significant increase in yield (up to a 50%) compared with maceration at room temperature and close to that obtained by boiling over the same time period. A note of caution is introduced when comparing UAE with Soxhlet extraction because, in the latter case, the liquid entering the Soxhlet extractor is more concentrated in methanol (nearly 100%) that the solvent in the reservoir (80% methanol) due to fractionation during distillation. The mechanism of UAE is discussed in terms of the effects of cavitation on the swelling index, solvent diffusion and the removal of a stagnant layer of solvent surrounding the plant material.     

Green ultrasound-assisted extraction of carotenoids from pomegranate wastes using vegetable oils

The objective of this work was to develop a new process for pomegranate peels application in food industries based on ultrasound-assisted extraction of carotenoids using different vegetable oils as solvents. In this way, an oil enriched with antioxidants is produced. Sunflower oil and soy oil were used as alternative solvents and the effects of various parameters on extraction yield were studied. Extraction temperature, solid/oil ratio, amplitude level, and extraction time were the factors investigated with respect to extraction yield. Comparative studies between ultrasound-assisted and conventional solvent extraction were carried out in terms of processing procedure and total carotenoids content. The efficient extraction period for achieving maximum yield of pomegranate peel carotenoids was about 30 min. The optimum operating conditions were found to be: extraction temperature, 51.5 °C; peels/solvent ratio, 0.10; amplitude level, 58.8%; solvent, sunflower oil. A second-order kinetic model was successfully developed for describing the mechanism of ultrasound extraction under different processing parameters.     

Kinetics of ultrasound-assisted extraction of antioxidant polyphenols from food by-products: Extraction and energy consumption optimization

Ultrasound-assisted extraction (UAE) of antioxidant polyphenols from chicory grounds was studied in order to propose a suitable valorization of this food industry by-product. The main parameters influencing the extraction process were identified. A new mathematical model for multi-criteria optimization of UAE was proposed. This kinetic model permitted the following and the prediction of the yield of extracted polyphenols, the antioxidant activity of the obtained extracts and the energy consumption during the extraction process in wide ranges of temperature (20–60 °C), ethanol content in the solvent (0–60% (vol.) in ethanol–water mixtures) and ultrasound power (0–100 W). After experimental validation of the model, several simulations at different technological restrictions were performed to illustrate the potentiality of the model to find the optimal conditions for obtaining a given yield within minimal process duration or with minimal energy consumption. The advantage of ultrasound assistance was clearly demonstrated both for the reduction of extraction duration and for the reduction of energy consumption.     

Aqueous ionic liquid based ultrasonic assisted extraction of eight ginsenosides from ginseng root

We developed an aqueous ionic liquid based ultrasonic assisted extraction (ILUAE) method for the extraction of the eight ginsenosides (ginsenoside-Rg1, -Re, -Rf, -Rb1, -Rc, -Rb2, -Rb3 and -Rd) from ginseng root. A series of l-alkyl-3-methylimidazolium ionic liquids differing in composition of anions and cations were evaluated for extraction efficiency. The results indicated that the ILUAE method has a remarkable ability to improve the extraction efficiency of ginsenosides. In addition, the ILUAE procedure was also optimized on some ultrasonic parameters, such as the IL concentration, solvent to solid ratio and extraction time. Under these optimal conditions (e.g., with 0.3 M [C₃MIM]Br, solvent to solid ratio of 10:1 and extraction time of 20 min), this approach gained the highest extraction yields of total ginsenosides 17.81 ± 0.47 mg/g. Compared with the regular UAE, the proposed approach exhibited 3.16 times higher efficiency and 33% shorter extraction time, which indicated that ILUAE has a broad prospect for sample preparation of medicinal plants.     

Optimization of ultrasonic cell grinder extraction of anthocyanins from blueberry using response surface methodology

Ultrasonic cell grinder extraction (UCGE), using water as the solvent, was firstly applied to extract anthocyanins from blueberry. Extraction yield was related with four variables, including ratio of solution to solid, extraction power, buffer time, and extraction time. On the basis of response surface methodology (RSM), the optimal conditions were determined to be the ratio of solution to solid as 25:1 (mL/g), the extraction power as 1500 W, the buffer time as 3.0 s, and the extraction time as 40 min. The experimental yield of anthocyanins using UCGE was 2.89 mg/g higher than that of conventional ultrasound-assisted extraction (CUAE). This study indicated that UCGE was an innovative, efficient, and environment friendly method in ultrasonic extraction fields, and had a potential to effectively extract other bioactive constituents.     

Instant controlled pressure drop technology and ultrasound assisted extraction for sequential extraction of essential oil and antioxidants

The instant controlled pressure drop (DIC) technology enabled both the extraction of essential oil and the expansion of the matrix itself which improved solvent extraction. The sequential use of DIC and Ultrasound Assisted Extraction (UAE) triggered complementary actions materialized by supplementary effects. We visualized these combination impacts by comparing them to standard techniques: Hydrodistillation (HD) and Solvent Extraction (SE). First, the extraction of orange peel Essential Oils (EO) was achieved by HD during 4 h and DIC process (after optimization) during 2 min; EO yields was 1.97 mg/g dry material (dm) with HD compared to 16.57 mg/g dm with DIC. Second, the solid residue was recovered to extract antioxidant compounds (naringin and hesperidin) by SE and UAE. Scanning electron microscope showed that after HD the recovered solid shriveled as opposite to DIC treatment which expanded the product structure. HPLC analyses showed that the best kinetics and yields of naringin and hesperidin extraction was when DIC and UAE are combined. Indeed, after 1 h of extraction, DIC treated orange peels with UAE were 0.825 ± 1.6 × 10^?2 g/g of dry material (dm) for hesperidin and 6.45 × 10^?2 ± 2.3 × 10^?4 g/g dm for naringin compared to 0.64 ± 2.7 × 10^?2 g/g of dry material (dm) and 5.7 × 10^?2 ± 1.6 × 10^?3 g/g dm, respectively with SE. By combining DIC to UAE, it was possible to enhance kinetics and yields of antioxidant extraction.     

Effect of oil extraction assisted by ultrasound on the physicochemical properties and fatty acid profile of pumpkin seed oil (Cucurbita pepo)

The effects of amplitude and time of ultrasound-assisted extraction on the physicochemical properties and the fatty acid profile of pumpkin seed oil (Cucurbita pepo) were evaluated. Ultrasound time (5–30 min) and the response variables amplitude (25–100%), extraction yield, efficiency, oxidative stability in terms of the free fatty acids (FFA) of the plant design comprising two independent experiments variables, peroxide (PV), p-anisidine (AV), totox value (TV) and the fatty acid profile were evaluated. The results were analyzed by multiple linear regression. The time and amplitude showed significant differences (P < 0.05) for all variables. The highest yield of extraction was achieved at 5 min and amplitude of 62.5% (62%). However, the optimal ultrasound-assisted extraction conditions were as follows: ultrasound time of 26.34 min and amplitude of 89.02%. All extracts showed low FFA (2.75–4.93% oleic acid), PV (1.67–4.68 meq/kg), AV (1.94–3.69) and TV (6.25–12.55) values. The main fatty acids in all the extracts were oleic and linoleic acid. Therefore, ultrasound-assisted oil extraction had increased performance and reduced extraction time without affecting the oil quality.