Effects of dielectric barrier discharge in air on morphological and electrical properties of graphene nanoplatelets and multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) have been functionalized by dielectric barrier discharge (DBD) in air. The extent of functionalization of MWCNTs and GNPs reaches a maximum at the delivered discharge energy of 720 and 240 J mg⁻¹, respectively. Further exposure to plasma leads to reduction of functional groups from the surface of the treated nanomaterials. It has also been demonstrated that DBD plasma does not produce dramatic structural changes in MWCNTs, while flakes of the treated GNPs become thinner and smaller in the lateral size. Conductive thin films, obtained by drop casting a solution of the treated nanomaterials in N-methyl-1-pyrrolidone on poly(methyl methacrylate) substrate, show significantly lower sheet resistance.     

Preparation, characterization and photocatalytic activity of multi-walled carbon nanotube-supported tungsten trioxide composites

Multi-walled carbon nanotube (MWCNT)-supported tungsten trioxide (WO₃) composite catalysts were prepared by liquid-phase process. WO₃ nanoparticles grew on the inner and outer surface of MWCNTs. Their photocatalytic activities in the degradation of the Rhodamine B Dye were studied. The effects of mass ratio of MWCNTs to WO₃ were discussed. X-ray diffraction, field emission transmission electron microscopy, thermogravimetric-differential thermal analysis and ultraviolet-visible light absorption spectra were carried out to characterize the composite catalysts. The results indicated that the optimum mass ratio of MWCNTs to WO₃ is 5:100.     

Effect of plasma treatment on electrical conductivity and Raman spectra of carbon nanotubes

Multi-walled carbon nanotubes (MWCNTs) were treated with a radio-frequency discharge. We found that MWCNTs showed opposite trends in electrical conductivity when treated with oxygen and hydrogen plasmas. MWCNTs showed enhanced electrical conductivity when placed at cathode with oxygen plasma treatment, whereas MWCNTs treated at positive column did not show such a trend. In contrast, the conductivity of MWCNTs dropped sharply with hydrogen plasma treatment. The measured conductivity trends of MWCNTs are correlated with observed Raman spectral shift. The possible mechanisms of the change in electrical conductivity in plasma-treated MWCNTs are discussed.     

Reduced graphene oxide/MWCNT hybrid sandwiched film by self-assembly for high performance supercapacitor electrodes

A reduced graphene oxide/multiwalled carbon nanotube (RGO/MWCNT) hybrid sandwiched film with different MWCNTs content was prepared by vacuum-assisted self-assembly from a complex dispersion of graphene oxide (GO) and MWCNTs followed by heat-treating at 200 °C for 1 h in a vacuum oven to reduce the GO into RGO. The free-standing RGO/MWCNT hybrid sandwiched film before heat-treatment showed a layered structure with an entangled network of MWCNTs sandwiched between the GO sheets. This unique structure not merely contribute to remove the oxygen-containing groups in GO during the heat-treatment, but also decrease the defects for electron transfer between RGO layers, which enhances the electrochemical capacitive performances of graphene-based films. A specific capacitance up to 379 F/g was achieved based on RGO/MWCNT with 30 % MWCNTs mass fraction at 0.1 A/g in a 6 M KOH electrolyte. The excellent performance of RGO/MWCNT hybrid sandwiched film signifies the importance of controlling the surface chemistry and sandwiched nanostructure of graphene-based materials.     

Thermal and electrical conductivity of poly(l-lactide)/multiwalled carbon nanotube nanocomposites

Multiwalled carbon nanotubes (MWCNTs) are considered to be the ideal reinforcing agent for high-strength polymer composites, because of their fantastic mechanical strength, high electrical and thermal conductivity and high aspect ratio. Polymer/MWCNTs composites are easily molded, and the resulting shaped plastic articles have a perfect surface appearance compared with polymer composites made using usual carbon or glass fibers. Good interfacial adhesion between the MWCNTs and the polymer matrix is essential for efficient load transfer in the composite. The ultrahigh strength polymer composites demand the uniform dispersion of the MWCNTs in the polymer matrix without their aggregation and the good miscibility between MWCNT and polymer matrix. This approach can also be applied to biodegradable synthetic aliphatic polyesters such as poly(l-lactide) (PLLA), which has received a great deal of attention due to environmental concerns. In this study, PLLA was melt-compounded with MWCNTs. A high degree of dispersion of the MWCNTs in the composites was obtained by grafting PLLA onto the MWCNTs (PLLA-g-MWCNTs). After oxidizing the MWCNTs by treating them with strong acids, they were reacted with l-lactide to produce the PLLA-g-MWCNTs. The mechanical properties of the PLLA/PLLA-g-MWCNT composite were higher than those of the PLLA/MWCNT composite. The electrical conductivity of the composites was determined by measuring the volume resistivity, which is a value of the resistance expressed in a unit volume by two-probe method. The thermal diffusivity and heat capacity of composites was measured by laser flash method, and the effects of modification of the MWCNT in PLLA matrix are discussed.     

Room-temperature power factor of CuAlO2 composite tablets enhanced by MWCNTs

CuAlO₂ with high theoretical thermoelectric performance has potential applications in thermal energy conversion. Herein, multi-wall carbon nanotubes (MWCNTs)/CuAlO₂ composite tablets are prepared by using different amounts of MWCNTs and solid paraffin binder, where MWCNTs served as a conductive agent and rendered three orders of magnitude increase in electrical conductivity. Seebeck coefficient of the composites was reduced with increasing MWCNTs content. Consequently, an optimal room-temperature thermoelectric power factor (PF) of 1.31 μW m⁻¹K⁻² has been rendered by MWCNTs/CuAlO₂ composite tablet with 1 wt % MWCNTs. Moreover, PF value increased with increasing temperature after a slight decrease at 333 K, which can be ascribed to the modulation of electrical conductivity. Current work provides an effective strategy to improve thermoelectric performance of CuAlO₂ materials.     

Charge conduction process and photoelectrical properties of bulk heterojunction device based on sulphonated nickel phthalocyanine and rose Bengal

The dependence of photovoltaic performance of the bulk heterojunction photovoltaic device based on the blend of sulphonated nickel phthalocyanine (NiPcS) and rose Bengal (RB) on their composition, thermal annealing and oxygen exposure has been investigated. It is found that both electron and hole mobility in RB phase and NiPcS phase, respectively has been increased on thermal annealing. The power conversion efficiency of the device increases upon thermal annealing, attributed the balance charge transport. The power conversion efficiency of the device experiences a drastic increase upon oxygen exposure, which attributed to the photo-induced doping, increase in exciton diffusion length in NiPcS phase and increased volume of exciton dissociation interfacial sites. From the impedance spectroscopy, we conclude that the change in bulk resistance and dielectric constant of the active material due to the illumination has a direct relevance to the photocurrent generated by the device.     

Integration and characterization of aligned carbon nanotubes on metal/silicon substrates and effects of water

We report here a facile way to grow aligned multi-walled carbon nanotubes (MWCNTs) on various metal (e.g. gold, tungsten, vanadium and copper)/silicon electrically conductive substrates by aerosol-assisted chemical vapor deposition (AACVD). Without using any buffer layers, integration of high quality MWCNTs to the conductive substrates has been achieved by introducing appropriate amount of water vapor into the growth system. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) determination indicate tidy morphology and narrow diameter distribution of the nanotubes as well as promising growth rate suitable for industrial applications. Raman spectra analysis illustrates that the structural order and purity of the nanotubes are significantly improved in the presence of water vapor. The growth mechanism of the nanotubes has been discussed. It is believed that water vapor plays a key role in the catalyst-substrate interaction and nucleation of the carbon nanotubes on the conductive substrates. This synthesis approach is expected to be extended to other catalyst-conductive substrate systems and provide some new insight in the direct integration of carbon nanotubes onto conductive substrates, which promises great potential for applications in electrical interconnects, contacts for field emitters, and other electronic nanodevices.     

The influence of hydrogen on the growth of gallium catalyzed silicon oxide nanowires

In this paper, we report that amorphous silicon oxide nanowires can be grown in a large quantity by chemical vapor deposition with molten gallium as the catalyst in a flow of mixture of SiH₄, H₂ and N₂ at 600 °C. Meanwhile, when we grow these nanowires under the same conditions but without H₂, octopus-like silicon oxide nanostructures are obtained. The reasons and mechanisms for the growth of these nanowires and nanostructures are discussed. Blue light emission is observed from SiO_x nanowires, which can be attributed to defect centers of high oxygen deficiency. These SiO_x nanowires may find applications in nanodevices and reinforcing composites.     

Effects of lithium phosphorous oxynitride film coating on electrochemical performance and thermal stability of graphite anodes

In this study, we investigated the effects of lithium phosphorus oxynitride (LiPON) solid electrolyte thin-film deposition on the electrochemical performance and thermal stability of pristine graphite and carbon-coated graphite composite anodes. The LiPON film was deposited by radio frequency (rf) magnetron sputtering. We studied the thermal stability of the lithiated electrodes when immersed in the presence of a liquid electrolyte by differential scanning calorimetry (DSC).The LiPON thin-film coating suppressed the impedance growth during the cycling process and inhibited the reaction between the lithiated electrode and the electrolyte, thus improving the cycle performance and thermal stability of the graphite electrode. However, for the carbon-coated graphite electrode, the heat evolution below 250 °C decreased, whereas that below 300 °C increased. We attributed this phenomenon to the low thermal stability of the LiPON thin-film coating owing to an exothermic reaction between the LiPON film and the electrolyte that occurs at approximately 290 °C.     

掺氢、掺氮碳纳米线的合成及其焊接

利用一种有效而别致的双离子(N⁺和Ar⁺)辐照和热处理技术合成并焊接无定形碳纳米线(ACNWs).实验样品用高分辨透射电子显微镜(HRTEM)进行了表征证实,适当搭配的双离子辐照与热处理的结合将会引起多壁碳纳米管无定形化并导致相互交叉纳米线的焊接.此外碳结构相变中的原子演化也在目前已有的概念基础上进行了简单地讨论. 关键词： 无定形碳纳米线 相变 透射电子显微镜     

Deposition of silver nanoparticles on carbon nanotube by chemical reduction method: Evaluation of surface,thermal and optical properties

Silver was stabilized on multi-walled carbon nanotubes (MWCNTs) by chemical-reduction technique using N,N-dimethylformamide (DMF) as a reducing agent. The influence of silver on the performance of carbon nanotubes (CNTs) was investigated by employing Fourier-transform infrared spectra (FTIR), Raman spectroscopy (RAS), thermal gravimetric analysis (TGA), zeta potential measurement, scanning electron microscope (SEM), electron dispersive X-ray spectrometer (EDX), transmission electron microscopy (TEM), and reflectance spectroscopy (RS). FTIR as well as RS methods evidenced the synthesis procedure using chemical reduction method was successful. Performing TGA of the samples under oxygen atmosphere demonstrated that the silver nanoparticles (Ag NPs) generated on MWCNTs surface can decrease the thermal stability of the particles by the catalytic oxidation of CNTs. In contrary, the thermal stability of the MWCNTs has improved under nitrogen atmosphere. EDX results showed the presence of Ag, Au and Co on the surface of deposited sample. The synthesised silver multi-walled carbon nanotubes (Ag–MWCNTs) were found to have higher UV reflection activity compared with untreated particles. The Ag–CNTs can be used in producing anti-UV composites.     

Thermal transport enhancement of multi-walled carbon nanotubes/ high-density polyethylene composites

Multi-walled carbon nanotubes (MWCNTs) enhanced high-density polyethylene (HDPE) composites were prepared and their thermophysical properties were measured. The thermal diffusivity of the composites increases with the increase in the amount of MWCNTs. A thermal diffusivity of more than three times that of pure HDPE was obtained for 38 vol. % MWCNTs/HDPE composites. An equation based on an effective medium approach model was used to discuss the thermal diffusivity enhancement of MWCNTs/HDPE composites as a function of the volume fraction of MWCNTs. The results from this analysis can be a predictive guideline for further improvements in the thermal transport properties of MWCNTs/HDPE composites. Moreover, the intrinsic longitudinal thermal conductivity k_z of an individual MWCNT was deduced from the measured results on the MWCNTs/HDPE composites. PACS 67.55.Hc; 61.46.Fg; 66.30.Xj     

Fabrication and field emission properties of multi-walled carbon nanotube/silicon nanowire array

Silicon nanowire (SiNW) arrays were fabricated on silicon wafers by the metal-assisted chemical etching method. Varied average diameters of SiNW arrays were realized through further treatment in a mixed agent of HF and HNO₃ of certain concentrations. After the treatment, there were more than 93% SiNWs with diameters smaller than 100 nm. The tip of each SiNW was subsequently wrapped with multi-walled carbon nanotubes (MWCNTs) with chemical vapor deposition method. The as-fabricated MWCNT/SiNW arrays were fabricated into electric field emitters, with turn-on field of 2.0 V/μm (current density: 10 μA/cm²), much lower than that of SiNW array (5.0 V/μm). The turn-on electric field of MWCNT/SiNW array decreased with the decreasing of the average diameter of SiNWs, indicating the performance of the field emission is relative to the morphology of SiNWs. As the SiNW array is uniform in height and easy to fabricate, the MWCNT/SiNW array shows potential applications in flat electric display.     

Electrical properties of transparent carbon nanotube networks prepared through different techniques

Ultra‐thin, optically transparent and electrically conducting films of pure carbon nanotubes (CNTs) are widely studied thanks to their promise for broad applications. In the present work, we study and compare different deposition techniques for the production of these networks: dip‐coating, spray‐coating, vacuum filtration and electrophoretic deposition on a quartz glass using single‐walled carbon nanotubes (SWCNTs) produced by the HiPCo method. In order to optimize the networks, besides the various deposition techniques we also investigate how the optical and electrical properties vary if the networks are fabricated from different CNTs, all synthesized by the CVD method: SWCNTs, DWCNTs and MWCNTs. As the main criteria for evaluating the quality of these CNT networks we measure the electrical surface resistance at a certain optical transmittance and correlate it to the morphology (homogeneity and roughness) of the networks. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

The Raman spectroscopic studies of aligned MWCNTs treated under high pressure and high temperature

The study of the aligned multiwalled carbon nanotubes (MWCNTs) for interlinking bonding under high pressures and temperatures have been conducted in the diamond anvil cell. The MWCNT samples were analyzed using the Raman spectroscopy, when treated under the combinations of pressure and temperature ranges of 2-20 GPa and 25-500 °C. The analyses show the formation of interlinking bonding at a pressure above 2.5 GPa when treated under the temperature 500 °C, based on the significant change of the relative intensity between D- and G-bands in the Raman spectra. Comparisons of the data obtained before and after the high pressure and high temperature treatments are reported. The result indicates that the aligned MWCNTs may be easier to form the interlinking bonding compared to randomly oriented MWCNTs.     

Thermal stability of catalytically grown multi-walled carbon nanotubes observed in transmission electron microscopy

The thermal stability of multi-walled carbon nanotubes (MWCNTs) was assessed in situ by transmission electron microscopy. Upon heating, Ni catalysts in MWCNTs containing bamboo structures shrank from the tail due to evaporation, leading to additional bamboo formation and tube elongation at 800°C, while the MWCNTs with FeSi catalysts remained intact up to 1050°C except for better crystallinity. The physisorbed carbon and/or hydrocarbon on surfaces and super-saturated carbon in the Ni catalysts should be responsible for the phenomena.     

Effect of different microwave-based treatments on multi-walled carbon nanotubes

Three new methods for the functionalization of multi-walled carbon nanotubes (MWCNTs) are reported using microwave (MW) energy and water as a mild chemical agent. In the first method we reported the effect of MW irradiation on a dispersion of MWCNTs in deionized water, in the second method we studied the exposing of MWCNT to microwave irradiation in the presence of steam, and in the third method we used microwave oven-generated plasma for the functionalization of MWCNTs. We also performed thermal oxidation and acid treatment as two conventional methods for oxidative functionalization of carbon nanotubes, to compare their effect with our results. Transmission electron microscopy (TEM) and Raman spectroscopy results showed that although these microwave methods introduced some defects to the carbon nanotubes, the damage was less severe than conventional treatments. X-ray photoelectron spectroscopy (XPS) measurements confirmed that the functionalization of carbon nanotubes by these methods favored hydroxyl groups, which are useful when further functionalization is required.     

Synthesis and characterization of rodlike liquid crystalline polyester/multi-walled carbon nanotubes and study of their thermal stability

Rodlike thermotropic liquid crystalline polyester (TLCP) was synthesized from 4,4′-oxydibenzoyl chloride and resorcinol containing modified multi-walled carbon nanotubes (MWCNTs) by in situ high-temperature solution polymerization. The liquid crystalline properties and thermal stability of the resulted TLCP nanocomposites were characterized by XRD, DSC, TGA, SEM, POM, and optical analysis. The addition of small amount of MWCNTs into TLCP matrix could significantly improve the thermal stability. The mesophase temperature range of nanocomposites were widened and shifted to higher temperatures. This nanocomposite melting phase transition (T_m) value increases maximally to 38.4 °C compared with pure copolymer. Using the Horowits-Metzger kinetic method, the PE/M-0.5 gave the best performance in terms of the thermal stability. This result can be explained that the incorporation of MWCNTs into TLCP caused an interaction between TLCP and MWCNTs through π-π* conjugation.     

Band-gap grading in Cu(In,Ga)Se2 solar cells

The quaternary system Cu(In,Ga)Se₂ (CIGS) allows the band gap of the semiconductor to be adjusted over a range of 1.04-1.67 eV. Using a non-uniform Ga/In ratio throughout the film thickness, additional fields can be built into p-type CIGS-based solar cells, and some researchers have asserted that these fields can enhance performance. The experimental evidence that grading improves device performance, however, has not been compelling, mostly because the addition of Ga itself improves device performance and hence a consistent separation of the grading benefit has not always been achieved. Numerical modeling tools are used in this contribution to show that (1) there can be a beneficial effect of grading, (2) in standard thickness CIGS cells the benefit is smaller than commonly believed, (3) there is also the strong possibility of reduced rather than of increased device performance, and (4) thin-absorber cells derive more substantial benefit.