Molecular interaction of Congo Red with conventional and cationic gemini surfactants

Interaction of tetradecyltrimethylammonium bromide (TTAB), octylophenylpolyoxyethylene ether (TX-100), sodium dodecylsulfate (SDS), N,N′-ditetradecyl-N,N,N′,N′-tetramethyl-N,N′-butanediyl-diammonium dibromide (14,4,14) and N,N′-didodecyl-N,N,N′,N′-tetramethyl-N,N′-butanediyl-diammonium dibromide (12,4,12) with an anionic diazo dye, Congo Red, was investigated using conductometry, spectroscopy, tensiometry, and pulsed field gradient NMR (PFG-NMR). The formation of dye-surfactant ion pairs, their small mixed aggregates (below the critical micelle concentration (CMC) of these surfactants) and surfactant micelles were detected successfully. Above the CMC, the dye reverted to its monomeric state and solubilized in the micelles. Job's method was used to determine the stoichiometric ratio of dye and surfactant in ion pairs and revealed the formation of more hydrophile ion pairs for geminis compared to their conventional analogs. Quantitative results obtained from tensiometry indicated the existence of considerable synergism for cationic surfactants and antagonism for anionic SDS. In addition, the synergism observed for TX-100 revealed the effect of π-π stacking and hydrophobic forces on ion pair and mixed micelle formation. The increase of dye-surfactant interactions by increasing the electrical charge and chain length of cationic surfactants confirmed the importance of both electrostatic and hydrophobic forces in binary dye/surfactant systems. The hydrodynamic radii of the micelles were determined by self-diffusion coefficient measurements. The average size of the cationic and nonionic micelles increased in the presence of CR molecules.     

Dye aggregation and influence of pre-micelles on heterogeneous catalysis: A photophysical approach

Common cationic dyes used for laser and fluorescent probes present low solubility in water. In order to increase the dye concentration in aqueous solutions, anionic surfactant can be added. The strong interaction between anionic surfactant and cationic dye can affect drastically the dye absorption and fluorescence properties. Here we observed that the fluorescence of the species in aqueous solution is maximized at condition of complete micellization of surfactants at critical micelle concentration (CMC). In addition, combined measurements of absorption, emission and fluorescence lifetime provide fundamental information on the critical concentration of H-aggregates formation and monomer separation, induced by pre-micelles and homomicelles on different surfactant sodium dodecylsulphate (SDS) concentration. The experimental results show how to find precisely the critical concentration of H-aggregates by optical method in two different xanthene-derived molecules: rhodamine 6G and rhodamine B. The adequate transference of electron from excited dye to the conduction band of semiconductor (TiO₂) promotes the creation of reactive species that provides the degradation of dye with advantage of use of irradiation in the visible region and strong photobleaching with direct exposure to the visible light irradiation in a scale of time of 10 min.     

On the concept of critical surface excess of micellization

The critical surface excess of micellization (CSEM) should be regarded as the critical condition for micellization of ionic surfactants instead of the critical micelle concentration (CMC). There is a correspondence between the surface excesses Γ of anionic, cationic, and zwitterionic surfactants at their CMCs, which would be the CSEM values, and the critical association distance for ionic pair association calculated using Bjerrum's correlation. Further support to this concept is given by an accurate method for the prediction of the relative binding of alkali cations onto dodecylsulfate (NaDS) micelles. This method uses a relative binding strength parameter calculated from the values of surface excess Γ at the CMC of the alkali dodecylsulfates. This links both the binding of a given cation onto micelles and the onset for micellization of its surfactant salt. The CSEM concept implies that micelles form at the air-water interface unless another surface with greater affinity for micelles exists. The process would start when surfactant monomers are close enough to each other for ionic pairing with counterions and the subsequent assembly of these pairs becomes unavoidable. This would explain why the surface excess Γ values of different surfactants are more similar than their CMCs: the latter are just the bulk phase concentrations in equilibrium with chemicals with different hydrophobicity. An intriguing implication is that CSEM values may be used to calculate the actual critical distances of ionic pair formation for different cations, replacing Bjerrum's estimates, which only discriminate by the magnitude of the charge.     

Solubilization of two organic dyes by cationic ester-containing gemini surfactants

Solubilization of two different types of organic dyes, Quinizarin with an anthraquinone structure and Sudan I with an azo structure, has been studied in aqueous solutions of a series of cationic gemini surfactants and of a conventional monomeric cationic surfactant, dodecyltrimethylammonium bromide (DTAB). Surfactant concentrations both above and below the critical micelle concentration were used. The concentration of solubilized dye at equilibrium was determined from the absorbance of the solution at λ(max) with the aid of a calibration curve. The solubilization power of the gemini surfactants was higher than that of DTAB and increased with increasing alkyl chain length. An increase in length of the spacer unit resulted in increased solubilization power while a hydroxyl group in the spacer did not have much effect. Ester bonds in the alkyl chains reduced the solubilization power with respect to both dyes. A comparison between the absorbance spectra of the dyes in micellar solution with spectra in a range of solvents of different polarity indicated that the dye is situated in a relatively polar environment. One may therefore assume that the dye is located just below the head group region of the micelle. Attractive π-cation interactions may play a role for orienting the dye to the outer region of the micelle.     

The solubility of ethane in aqueous solutions of sodium 1-pentanesulfonate, sodium 1-hexanesulfonate, sodium 1-heptanesulfonate, and sodium 1-octanesulfonate at 25 degrees C

Measurements have been made to determine the solubility of ethane, C2H6, in aqueous solutions of four different surfactants of the linear alkanesulfonate class at 25 degrees C. The surfactants, sodium 1-pentanesulfonate, sodium 1-hexanesulfonate, sodium 1-heptanesulfonate, and sodium 1-octanesulfonate, all share a common head group (-SO-3) and counter ion (Na+), and differ only in the length of the alkyl chain attached to the head group. The solubility of ethane has been determined as a function of surfactant concentration for each surfactant. At surfactant concentrations below the critical micelle concentration (CMC), the solubility of ethane is quite low and differs only slightly from the solubility of ethane in pure water. At concentrations greater than the CMC, the solubility of ethane exhibits a gradual increase with surfactant concentration. At high surfactant concentrations, well in excess of the CMC, the solubility of ethane is found to increase as a linear function of surfactant concentration. From this data it becomes possible to determine the fractional population of the surfactant in the free and micellized states. The solubility data measured for ethane is interpreted in terms of the mass-action model for micelle formation.     

Effects of Fructose and Temperature on the Micellization of a Cationic Gemini Surfactant,Pentanediyl-1,5-bis(dimethylcetylammonium) Bromide in Aqueous Solutions

By the conductivity measurements the effects of fructose and temperature (293–308 K) on the micellization of a cationic gemini surfactant (GS), pentanediyl-1,5-bis(dimethylcetylammonium) bromide in aqueous solutions have been investigated. The critical micelle concentration (CMC) of GS was measured at the different temperatures and fructose concentrations. An increasing trend of the CMC values is with addition of fructose. With increasing temperature, the CMC values are in a similar increasing trend. The CMC of GS by dye solubilization method at room temperature have been determined. The standard Gibbs energy, enthalpy and entropy of GS micellization have been evaluated. From these thermodynamic parameters, it was found that in presence of fructose, the stability of the GS aqueous solutions decreases.     

Interaction of surfactants and aminoindophenol dye

The interaction of dye and surfactants was studied by their spectroscopic and surface properties. Large bathochromic shift (15 nm) in the absorption spectrum was found for aminoindophenol dye at high pH in cationic surfactant, while there is no significant shift in anionic, zwitterionic and nonionic surfactant solutions. The static and dynamic surface properties show there is strong interaction in mixture of cationic surfactant and aminoindophenol dye. Interaction of dye and surfactants on surface and in solution is correlated to the intensity of dye deposition on fiber. The charge complex formation between cationic surfactant and aminoindophenolic dye delays the dye diffusion into keratin fiber. The stronger is the dye/surfactant interaction, the lower dye deposition and diffusion become.     

Determination of Surfactants Using Ion Pair Extraction of Near-infrared Laser Dyes

Abstract

Ionic surfactants and near-infrared laser dyes formed complexes which were extracted into organic solvents as ion pairs. Surfactants were determined spectrophotometrically by measuring the near-infrared absorbance and fluorescence of the ion pair in the organic solvent. Several of the commercially available near infrared dyes have been found suitable for surfactant determination in water using this technique. The excess near-infrared dye coextracted into the organic solvent was determined by blank extractions. The calibration curves were linear within two orders of magnitude of surfactant concentrations. Non-linear calibration curves are obtained for wider concentration range of surfactants. This method using the recently developed near-infrared laser diode intracavity technique was applied to the determination of SDS in water. Lower detection limits and ease of operation are the major advantages of using this new laser diode technique. The extraction efficiency of different solvent systems was evaluated.     

Specific ion pairing and interfacial hydration as controlling factors in gemini micelle morphology. Chemical trapping studies

Results from chemical trapping experiments in micellar solutions containing 1.5-5 mM aqueous solutions of three didodecyl dicationic dibromide gemini surfactants with different methylene spacer lengths (12-n-12 2Br where n = 2-4 CH(2) groups) gave quantitative estimates of the molarities of interfacial bromide (Br(m)) and water (H(2)O(m)), the fractions of free and paired headgroups and counterions, and the net headgroup charge. These results are one of the most detailed compositional studies of an association colloid interface to date. Br(m) increases and H(2)O(m) decreases as n decreases and the two cationic charges are closer together. The 12-2-12 2Br gemini (the only one of the three geminis known to form threadlike micelles) shows a marked increase in Br(m) (from 2.3 to 3.6 M) and a decrease in H(2)O(m) (from 35 to 17 M) at the exceptionally low surfactant concentration in the vicinity of the previously reported sphere-to-rod transition or second cmc concentration. Rod formation occurs because of an increase in headgroup-counterion association and dehydration at the micelle surface that depend on both the free energies of hydration and specific ion interactions and surfactant and counterion concentrations. These and other recent chemical trapping results support a new model for the balance of forces controlling morphological transitions of association colloids. The hydrophobic effect drives the formation of headgroup-counterion pairs, which have a lower demand for water of hydration. Release of water permits tighter packing and formation of cylindrical aggregates.     

Counterion binding on mixed anionic/cationic micelles

Measurements of counterion binding in mixtures of surfactant aqueous solutions have been performed to study the structure of the anionic/cationic mixed micelle/solution interface. The mixtures studied were SDS/DDAC and STS/TDPC. The binding of chloride and sodium ions to mixed anionic/cationic micelles was measured using ion-specific electrodes. Counterion binding was found to be strongly dependent on the molar ratio of surfactants present. The mixed micelle/solution interface includes the headgroups of both surfactants and counterions of surfactant in excess. The addition of oppositely charged surfactant caused an increasing dissociation of counterions.     

Wettability of a glass surface in the presence of two nonionic surfactant mixtures

Measurements of the advancing contact angle (theta) were carried out for aqueous solution of p-(1,1,3,3-tetramethylbutyl)phenoxypoly(ethylene glycol), Triton X-100 (TX100), and Triton X-165 (TX165) mixtures on glass. The obtained results indicate that the wettability of glass depends on the concentration and composition of the surfactant mixture. The relationship between the contact angle and concentration suggests that the lowest wettability corresponds to the concentration of TX100 and TX165 and their mixture near the critical micelle concentration (CMC). The minimum of the dependence between the contact angle and composition of the mixtures for each concentration at a monomer mole fraction of TX100, alpha, equals 0.2 and 0.4 points to synergism in the wettability of the glass surface. In contrast to the results of Zisman ( Zisman, W. A. In Contact Angle, Wettability and Adhesion; Gould, R. F., Ed.; Advances in Chemistry Series 43; American Chemical Society Washington, DC, 1964; p 1 ) there was no linear dependence between cos theta and the surface tension of aqueous solutions of TX100 and TX165 mixtures for all studied systems, but a linear dependence exists between the adhesional tension and surface tension for glass, practically, in the whole concentration range of surfactants studied, the slopes of which are positive in the range of 0.43-0.67. These positive slopes indicate that the interactions between the water molecules and glass surface might be stronger than those between the surface and surfactant molecules. So, the surface excess of surfactant concentration at the glass-water interface is probably negative, and the possibility for surfactant to adsorb at the glass/water film-water interface is higher than that at the glass-water interface. This conclusion is confirmed by the values of the work of adhesion of "pure" surfactants, aqueous solutions of surfactants, and aqueous solutions of their mixtures to the glass surface and by the negative values of glass-water interfacial tension determined from the Young equation in the range of surfactant concentrations corresponding to their unsaturated monolayer at the water-air interface.     

Studies on the Interaction of Surfactants with Cationic Dye by Absorption Spectroscopy

The interaction of methyl violet, a cationic dye, with various surfactants, viz. anionic (SDS), nonionic (Triton X-100), and cationic (CTAB), has been investigated spectrophotometrically in submicellar and micellar concentration range. While in the submicellar concentration region of SDS the higher aggregates of the dye are found, in the micellar concentration region the monomer of the dye predominates. With nonionic surfactant the dye is solubilized primarily as the monomer. CTAB produces no perturbation to the visible spectra of the dye. In the presence of strong electrolytes such as NaNO(3) and NaCl the dye aggregates are formed at a much lower SDS concentrations. Copyright 2000 Academic Press.     

Unusual aqueous-phase behavior of cationic amphiphiles with hydrogen-bonding headgroups

Two cationic surfactants with hydroxyl and carbamate hydrogen-bonding sites at their headgroups were synthesized. Both surfactants are ionic liquids (one of them at room temperature). Samples are isotropic solutions over the entire 0-100% concentration range, which is highly unusual for ionic surfactants. Surface tension, NMR, and conductivity measurements indicate classical micelle formation in aqueous solutions with CMCs below 10 mM. Pulse-gradient spin-echo (PGSE) NMR confirms micelle formation and provides micellar hydrodynamic radii of about 3.8 nm. Because this value is larger than the length of the extended surfactant molecules, about 2.7 nm, it appears that hydrogen-bonded water of hydration contributes substantially to the effective micelle size. At higher concentrations (above 25 wt %), surfactant solutions become viscous, but line broadening in the NMR is small relative to that found with a conventional cationic surfactant (CTAB). Thus, long rod formation, the source of line broadening in the latter, is absent with the new surfactants. Finally, PGSE NMR data show a 5-fold decrease in the diffusion coefficient between 5 and 20 wt %, above which the diffusion coefficients remain constant. The results are best explained by micelle clustering that is likely aided by intermicellar hydrogen bonding. The possibility of an isotropic liquid crystal (LC) phase with cubic symmetry is discussed and dismissed, demonstrating that LC formation of ionic surfactants at high concentrations, the usual behavior in past work, need not occur. Nor is there a definite connection between ionic liquid behavior and isotropic morphology.     

Adsorption and Micellization in Solutions of Dodecylpyridinium Bromide–Nonionic Surfactant Mixtures

Dependences of the surface tension of aqueous solutions of cationic (dodecylpyridinium bromide) and nonionic (Tween 80, Triton X-100) surfactants and their mixtures on total surfactant concentration and solution composition were studied. The values of critical micellization concentration (CMC) and excess free energy of adsorption were determined from tensiometric measurements. Based on Rubingh–Rosen model (approximation of the theory of regular solutions), the compositions of micelles and adsorption layers at the solution–air interface as well as parameters of interaction between the molecules of cationic and nonionic surfactants were calculated for the systems indicated above. It was established that, in the case of surfactant mixtures with considerable difference in the CMCs, the micelles of individual surfactant with lower CMC value are formed. The effect of negative deviation from the ideality during the adsorption of surfactants from mixed solutions at the solution–air interface was disclosed. It was shown that the interaction energy depends significantly on the composition of mixed systems.     

Mixing behavior of fluorinated and hydrogenated gemini surfactants at the air-water interface

Mixing behavior of hydrogenated and fluorinated cationic gemini surfactants was studied at the air-water interface by Brewster angle microscopy and pi-A isotherm curves. In the bulk, these two molecules did not mix and showed phase separation. At the air-water interface, if a monolayer was formed by separate deposition of the two solutions, they formed separate domains, and the compression occurred in two steps: first the domains with hydrogenated gemini surfactant were compressed until they showed collapse; then the domains with fluorinated gemini surfactant were compressed. If the two solutions were mixed before the deposition, they remained mixed upon compression; on the other hand, separate domains under separate deposition were shown to mix if the subphase was heated.     

Adsorption and micelle formation of alkylammonium chloride-alkyltrimethylammonium chloride mixtures

The surface tension of the aqueous solutions of binary cationic surfactant mixtures of (1) dodecylammnonium chloride (DAC)-tetradecyltrimethylammonium chloride (TTAC), (2) decylammonium chloride (DeAC)-dodecyltrimethylammonium chloride (DTAC), and (3) DAC-DTAC was measured as a function of the total molality and composition of surfactants at 298.15 K. The compositions of surfactants in the adsorbed film and micelle were evaluated and the phase diagram of adsorption and that of micelle formation were constructed. Furthermore the excess Gibbs energies of adsorption and micelle formation were calculated to estimate the deviation from the corresponding ideal mixing. It was found that the surface and micelle are enriched in trimethylammonium salts in (1) and (2), while in ammonium salt in (3) compared to the bulk solution. On the other hand, the micelle is enriched in trimethylammonium salts compared to the surface at the critical micelle concentration (CMC) in all the systems. The miscibility of the surfactants was clarified from the standpoints of the structure of the head group and of the matching between the size of polar head group of surfactants and the difference in hydrocarbon chain length.     

Atmospheric and electrochemical oxidation of ascorbic acid in anionic,nonionic and cationic surfactant systems

It is well known that the antioxidant activity of some species in homogenous solutions may not be the same as that in heterogeneous media. This environment dependence is the reason for investigating ascorbic acid antioxidant activity in surfactant solutions. In our study we have investigated the kinetics of atmospheric oxidation and electrochemical oxidation of ascorbic acid in aqueous solutions of the four surfactants: SDS, AOT (anionic), TRITON-100 (nonionic), and CTAB (cationic). For each surfactant the concentrations below and above CMC were investigated. As expected, a general trend in the atmospheric oxidation rate changes in the following manner: the micellar solution of nonionic surfactant shows a faster oxidation rate than that of the anionic surfactant, and the cationic surfactant an even higher one. The more subtle effects were observed with each surfactant concentration change. The influence of the surfactants on the electrochemical behavior of ascorbic acid was also studied. A general conclusion emerging from our investigation is that surfactants shift the ascorbic acid oxidation potential and change the peak current value. This phenomenon is due mainly to the surfactant film formed at the electrode/solution interface.     

Determination of critical micelle concentration with the rotating sample system

A novel experimental approach using the rotating sample system (RSS) is proposed here for the determination of the critical micelle concentration (CMC) of surfactants. The RSS has been conceived in our laboratory as a convection platform for physicochemical studies and analyses in microliter-sized sample drops. The scheme allows for vigorous rotation of the drop despite its small size through efficient air-liquid mechanical coupling. Thus, changes in surface properties of aqueous samples result in corresponding modulation of the hydrodynamic performance of the RSS, which can be utilized to investigate interfacial phenomena. In this work, we demonstrate that the RSS can be used to study the effects of surfactants on the surface and in the bulk of very small samples with hydrodynamic electrochemistry. Potassium ferrocyanide is employed here with cyclic voltammetry to probe the air-water interface of solutions containing Triton X-100. The CMC of this surfactant determined using this approach is 140 ppm, which agrees well with reported values obtained with conventional methods in much larger samples. The results also demonstrate that besides the CMC, variations in bulk rheological properties can also be investigated in very small specimens using the RSS with a simple method.     

Synergism in the spreading of hydrocarbon-chain surfactants on polyethylene film-anionic and cationic mixtures by a two-step procedure

A study has been made of the adsorption, interaction, and spreading of mixtures of anionic and cationic surfactants at the aqueous solution/polyethylene (PE) interface. When a drop of an aqueous solution of an anionic or cationic hydrocarbon-chain surfactant is placed on a highly hydrophobic PE film (contact angle of water > 90 degrees ), it spreads to an area very little larger than that of a drop of water of the same volume. If the anionic and cationic hydrocarbon-chain surfactant solutions are mixed prior to being applied to PE film, synergism is small, if any, and the reproducibility of the experimental results is poor. However, when the cationic and anionic aqueous solutions are applied on the PE film in a sequential manner, a remarkable synergism in spreading is observed and the results are very reproducible. The area spread by an aqueous solution of the anionic-cationic mixture may be more than 400 times that of aqueous solutions of the same volume and surfactant concentration of the individual surfactant components. Previous work in this laboratory on surfactant systems showing synergism in spreading on PE film, but only weak interaction at the aqueous solution/air interface, showed that the synergy was due to changes at the aqueous solution/PE interface and not to the changes at the aqueous solution/air or PE/air interface. Investigation of the adsorption behavior at the aqueous solution/solid interface of two of the anionic-cationic mixtures studied here indicates the reason for differences in spreading behavior observed with different anionic-cationic mixtures. The more similar the adsorption tendencies at the solid/aqueous solution interface of the anionic and cationic surfactants, and the closer their adsorption to an equimolar monolayer there, the stronger their interaction there and the greater their enhancement of the spreading. A mechanism is proposed for the synergy in spreading observed, based upon the difference between the surface tension in the precursor film at the spreading interface and that at the top of the spreading drop.