3D FINITE ELEMENT ANALYSIS OF THE DAMAGE EFFECTS ON THE DENTAL COMPOSITE SUBJECT TO WATER SORPTION

The damage effects of water sorption on the mechanical properties of the hydroxya-patite particle reinforced Bis-GMA/TEGDMA copolymer (HA/Bis-GMA/TEGDMA) have been predicted using 3D finite cell models. The plasticizer effect on the polymer matrix was considered as a variation of its Young's modulus. Three different cell models were used to determine the influence of varying particle contents, interphase strength and moisture concentration on the debonding damage. The stress distribution pattern has been examined and the stress transfer mode clarified. The Young's modulus and fracture strength of the Bis-GMA/TEGDMA composite were also predicted using the model with and without consideration of the damage. The former results with consideration of the debonding damage are in good agreement with existing literature experimental data. The shielding effect of our proposed model and an alternative approach were discussed. The FCC cell model has also been extended to predict the critical load for the damaged and the undamaged composite subject to the 3-point flexural test.     

含共晶界面陶瓷复合材料的损伤应变场分析

研究了含共晶界面陶瓷复合材料的损伤应变场及其尺度效应。根据含共晶界面复合陶瓷的细观结构特性,利用含共晶界面陶瓷复合材料中三相胞元内的应力场分布规律,得出棒状共晶体内的无损应变场分布规律。针对棒状共晶体内存在损伤的现象,通过引入损伤变量,利用三相模型法得到了棒状共晶体内存在损伤时的应变场分布规律;根据应变和纤维状夹杂直径之间的关系,分析了棒状共晶体内的损伤应变场及其尺度效应。结果表明,含共晶界面陶瓷复合材料内三相胞元中基体、界面相和纤维夹杂内的损伤应变场对纤维夹杂直径具有明显的尺度效应。     

极端环境下连续碳纤维增韧的陶瓷基复合材料的力学行为

连续纤维增韧的碳化硅复合材料(以下简称C/SiC),作为超高速飞行器热结构使用时,有可能在高温环境下受到高速撞击的作用,因此,掌握其在极端环境(高温、高应变率)下的力学性能是进行结构安全设计的基础。本文采用具有高温实验能力的分离式Hopkinson杆,在293~1273K温度范围内进行了动态压缩力学性能测试,研究了环境温度和加载速率对材料力学性能的影响。结果表明:C/SiC复合材料的高温压缩力学性能主要受应力氧化损伤和残余应力的共同影响。实验温度低于873K时,应力氧化损伤的影响很小,而由于增强纤维和基体界面残余应力的释放使界面结合强度增大,复合材料的压缩强度随温度的升高而增大;当实验温度高于873K时,应力氧化损伤加剧,其对压缩强度的削弱超过残余应力释放对强度的贡献,材料的压缩强度随温度的升高逐渐降低。由于应力氧化损伤受应变率的影响很大,当温度由873K升高至1273K时,高应变率下压缩强度降低的程度要比应变率为0.0001/s时低得多。     

Influences of reinforcing particle and interface bonding strength on material properties of Mg/nano-particle composites

In the present study, an effective model is proposed to predict the effective elastic behavior of the three-phase composite containing spherical inclusions, each of which is surrounded by an interphase layer. The constitutive equations are derived for the stress and strain of each phase of the composite subjected to a far-field tension. Based on these constitutive laws, the effective bulk, shear and Young’s modulus are obtained. A statistical debonding criterion is adopted to characterize the varying probability of the evolution of interphase debonding. Influences of debonding damage, particle volume fraction, interphase properties and bonding strength on overall mechanical behavior of composites are also discussed. Numerical analyses are carried out on particle-reinforced composites and the predictions have a good agreement with the experimental results.     

A thermodynamics based damage mechanics model for particulate composites

A micro-mechanical damage model is proposed to predict the overall viscoplastic behavior and damage evolution in a particle filled polymer matrix composite. Particulate composite consists of polymer matrix, particle fillers, and an interfacial transition interphase around the filler particles. Yet the composite is treated as a two distinct phase material, namely the matrix and the equivalent particle-interface assembly. The CTE mismatch between the matrix and the filler particles is introduced into the model. A damage evolution function based on irreversible thermodynamics is also introduced into the constitutive model to describe the degradation of the composite. The efficient general return-mapping algorithm is exploited to implement the proposed unified damage coupled viscoplastic model into finite element formulation. Furthermore, the model predictions for uniaxial loading conditions are compared with the experimental data.     

Interaction between edge dislocations and amorphous interphase in carbon nanotubes reinforced metal matrix nanocomposites incorporating interface effect

Dislocations mobility and stability in the carbon nanotubes (CNTs)-reinforced metal matrix nanocomposites (MMNCs) can significantly affect the mechanical properties of the composites. However, current processing techniques often lead to the formation of coated CNT (amorphous interphase exists between the reinforcement and metal matrix), which have large impact upon the image force exerting on dislocations. Even though the importance of the interphase zone formed in metal matrix composites has been demonstrated by many studies for elastic properties, the influence of interphase on the local elastoplastic behavior of CNT-reinforced MMNCs is still an open issue. This paper puts forward a three-phase composite cylinder model with new boundary conditions. In this model, the interaction between edge dislocations and a coated CNT incorporating interface effect is investigated. The explicit expressions for the stress fields and the image force acting on an edge dislocation are proposed. In addition, plastic flow occurring around the coated reinforcement is addressed. The influences of interface condition and the material properties of coated CNT on the glide/climb force are clearly analyzed. The results indicate that the interface effect becomes remarkable when the radius of the coated reinforcement is below 10 nm. In addition, different from the traditional particles, the coated CNT attracts the adjacent edge dislocations, causing pronounced local hardening at the interface between the interphase and the metal matrix under certain conditions. It is concluded that the presence of the interphase can have a profound effect on the local stress field in CNT-reinforced MMNCs. Finally, the condition of the dislocations stability and the equilibrium numbers of dislocations at a given size grain are evaluated for considering the interface effect.     

界面特性对短纤维金属基复合材料蠕变行为的影响

基于短纤维增强金属基复合材料(MMC)的单纤维三维模型(三相)，利用粘弹性有限元分析方法对影响金属基复合材料的蠕变行为的因素进行了较为系统的分析。研究中主要讨论了界面特性和纤维取向角对金属基复合材料的蠕变性能的影响。研究结果发现，界面特性诸如厚度、模量和应力指数都对纤维最大轴应力和稳定蠕变率产生影响：稳态蠕变率随界面模量的增大而逐渐减小，当高于基体模量时基本保持不变；纤维轴应力的变化与蠕变率正好相反。稳态蠕变率随界面厚度、应力指数的增加而增大；而轴应力则随之减小。同时不同的纤维取向也影响金属基复合材料蠕变时的轴应力分布和稳态蠕变率。     

Influence of cracking on tensile behavior of brittle materials

This paper deals with mechanical behavior of quasi-brittle materials in tension, such as concrete. Two elementary LEFM models are presented. Attention is focused on the crack phenomenon, highlighting the influence of initial damage on structural response. The first model consists of a plate of finite size with a central crack. The second model corresponds to an infinite plate with an infinite set of collinear cracks of equal length and spaced at a constant distance apart. For both models, an analytical study is conducted which leads to a determination of the link between critical stress and displacement, initially considering only the incremental displacement due to the damage present in the material, and subsequently also taking into account the elastic compliance of the structure. An analysis is also performed in which the concomitance of brittle fracture and plastic collapse is considered, which reveals interesting scale effects.     

含有多个涂层压电纤维复合材料的平面问题研究

压电纤维在未来的复合材料结构健康监测中具有重要作用．本文基于横观各向同性压电材料位移和应力连续条件以及经典的复势函数理论,讨论了同时受到平面内机械载荷和出平面电载荷作用时含有多个带涂层压电纤维的无限大线弹性基体的平面力学问题．首先将线弹性基体、涂层和压电纤维的应力场、位移场表示成复势函数,然后通过横观各向同性压电材料和线弹性材料的位移和应力连续条件确定复势函数表达式．将得到的复势函数表达式代入线弹性基体、涂层和压电纤维的的应力场、位移场公式可确定其应力场和位移场．最后,通过定量的案例讨论了涂层的材料属性对线弹性基体应力场的影响．案例分析表明涂层的材料属性对压电复合材料的应力场有重要的影响．     

Local shrinkage and stress induced by thermo-oxidation in composite materials at high temperatures

The paper is concerned with the modelling, simulation and experimental characterisation of local shrinkage strains and stresses induced by thermo-oxidation phenomena in the IM7/977-2 carbon/epoxy composite material at elevated temperatures. The oxygen concentration and mechanical fields were established through a coupled model constructed from a unified multiphysical approach and the thermodynamics of irreversible processes. The model was implemented in the ABAQUS^® finite element commercial code. Simulations of thermo-oxidation-induced matrix shrinkage were run at a local scale, i.e., the scale of the elementary constituents of the composite, the fibre and the matrix. The experimental assessment was done at the same scale, and the local matrix shrinkage profiles were measured by confocal interferometric microscopy.A good agreement was found between the simulated and measured profiles, validating the unified model. The thermo-oxidation induced stress field was analysed to understand the influence of the environment on the onset of damage in composite materials at elevated temperature.     

An enriched damage-frictional cohesive-zone model incorporating stress multi-axiality

The paper presents an interphase cohesive zone model (CZM) incorporating stress multi-axiality devised to capture, by simplified micro-modeling, the influence of the in-plane strain and stress state in the mechanical response of the CZM. Moreover, the model is able to account for the Poisson-related effect in the interphase, which can play an important role in the modeling of heterogeneous masonry elements. From the constitutive point of view, the proposed formulation couples damage and friction by addressing a smooth transition from a quasi-brittle response to a residual frictional behavior described by a Coulomb law with unilateral contact. As in-plane stresses are accounted for, damage activation and evolution are governed by a Drucker–Prager law with linear softening. A predictor-corrector procedure based on a backward Euler scheme is detailed for integrating the nonlinear evolutive problem together with the related tangent operator which consistently linearizes the algorithmic strategy. This framework is embedded into a kinematically-enriched finite element interphase formulation incorporating stress multi-axiality. The modeling features of the resulting numerical tool are tested both at the local level, for the typical interphase point, and in meso-structural tests consisting of brick-mortar triplets, investigating the capability of the proposed model and numerical procedure to simulate the brick-mortar decohesion mechanism during confined slip tests.     

An improved model of thin cylindrical piezoelectric layers between isotropic elastic media

Radially polarized piezoelectric fibers are now considered to be used in smart composites. The piezoelectric layers in these fibers are generally anisotropic in the transverse direction and therefore difficult to analyze when dynamic loads are involved. The present paper presents a theoretical study of the dynamic behavior of radially polarized cylindrical piezoelectric layers between isotropic elastic media. A new interphase model is developed to provide simple yet accurate evaluation of the dynamic response of such anisotropic elastic layers. Unlike the traditional interface-spring model, the current interphase model satisfies the equations of motion of the layers and can provide reliable prediction of the stress and displacement. A comparison between the developed model, the interface-spring model and the finite element analysis is conducted. The results clearly show the advantages of the current model over the traditional interface-spring model in simulating anisotropic layers. Numerical examples based on this interphase model for different interphase thicknesses, loading frequencies and material combinations are presented to evaluate the dynamic behavior of multilayered elastic media.     

考虑收缩徐变影响的新旧混凝土叠合梁单元刚度矩阵改进

混凝土自身的收缩徐变会在新旧混凝土叠合梁中使应力重分布.为了计算重分布应力,首先推导以挠度表达的叠合梁非线性微分方程,然后通过求解该微分方程,引入位移形函数、刚度形函数和等效节点载荷形函数,最后得出新混凝土梁、旧混凝土梁和Goodman弹性夹层三合一的叠合梁改进型单元刚度矩阵和等效节点载荷,从而为收缩徐变影响下的混凝土的内力计算提供了一种有效的新方法.文中还进行了实例验证分析,并从中得出了一些有益的结论.     

含界面相复合材料热残余应力分析

本文分析了含有界面相纤维增强复合材料热残余应力的空间分布。针对材料实际微结构几何特点,建立含有界面相的三维三相单丝模型,用均匀和梯度函数描述界面相模量随空间变化规律,由轴对称体弹性力学理论得到单丝热残余应力分布,结果表明梯度界面降低了残余应力。通过碳纤维电阻法测出T300/环氧树脂单丝体系固化后的纤维轴向应变,与梯度界面的分析结果基本一致。用叠加方法得到密排六方结构代表性体积元(RVE)中纤维间相互偶合的应力场,同时应用有限元法分析RVE中纤维间的残余应力分布,两者结果相互验证。     

Failure behavior of composite sandwich structures under local loading

Usually when analyzing the mechanical response of foam-cored fiber-reinforced composite sandwich structures to localized static loading, the face sheets are treated as a linear-elastic material and no damage initiation and growth is considered. However, practice shows that at higher indentation magnitudes damage develops in the face sheet in the area of contact with the indentor, which could lead to local failure of the face laminate due to the loss of bending stiffness and strength. Therefore, the main objective of the present study is to develop a damage model for predicting the local failure in the composite face sheet and its influence on the load–displacement behavior of sandwich structures under local loading. For this purpose, the Hoffman failure criterion is incorporated into a finite element modeling procedure using the ABAQUS program system. Results deducted from the modeling procedure are compared with experimental data obtained in the case of static indentation tests performed on sandwich beam specimens using steel cylindrical indentors. It is shown that taking into account the damage in the face sheet leads to a substantial improvement in the performance of the model when simulating the mechanical behavior of the sandwich structures at higher indentation values.     

尼龙6/蒙脱土复合材料蠕变行为研究

针对经典黏弹性模型不能很好分析黏弹性材料的蠕变行为问题,运用分数阶导数的类标准线性体模型与Prony级数模型研究了黏弹性材料尼龙6/蒙脱土复合材料的蠕变行为.采用原位聚合法制备了尼龙6/蒙脱土复合材料,在室温环境下对其进行蠕变实验.然后运用分数阶导数的类标准线性体模型和Prony级数模型对复合材料的蠕变实验数据进行分析...     

Biothermomechanics of skin tissues

Biothermomechanics of skin is highly interdisciplinary involving bioheat transfer, burn damage, biomechanics and neurophysiology. During heating, thermally induced mechanical stress arises due to the thermal denaturation of collagen, resulting in macroscale shrinkage. Thus, the strain, stress, temperature and thermal pain/damage are highly correlated; in other words, the problem is fully coupled. The aim of this study is to develop a computational approach to examine the heat transfer process and the heat-induced mechanical response, so that the differences among the clinically applied heating modalities can be quantified. Exact solutions for temperature, thermal damage and thermal stress for a single-layer skin model were first derived for different boundary conditions. For multilayer models, numerical simulations using the finite difference method (FDM) and finite element method (FEM) were used to analyze the temperature, burn damage and thermal stress distributions in the skin tissue. The results showed that the thermomechanical behavior of skin tissue is very complex: blood perfusion has little effect on thermal damage but large influence on skin temperature distribution, which, in turn, influences significantly the resulting thermal stress field; the stratum corneum layer, although very thin, has a large effect on the thermomechanical behavior of skin, suggesting that it should be properly accounted for in the modeling of skin thermal stresses; the stress caused by non-uniform temperature distribution in the skin may also contribute to the thermal pain sensation.     

基于抗损性的钢筋混凝土摇摆柱力学性能研究

抗震韧性将震后建筑的功能维持或快速恢复作为最终目标。构件层次的摇摆机制是实现主体结构功能可恢复的有效途径,但应以构件的抗损性为前提。以钢筋混凝土摇摆柱为对象,比拟弹性半空间局部受载经典拉芒（Flamant）理论,推导摇摆柱轴向应力分布弹性力学解答,以此为基础,假定摇摆柱侧移由柱端接触面转角和柱身弯剪变形引起,建立钢筋混凝土摇摆柱荷载-侧移力学模型,与有限元模拟结果对比验证合理性。开展轴压比和柱端强度分析,结果表明,在柱体抗损的前提下,单纯提高轴压比可提高柱体承载能力,但对侧移能力提升不显著;随着柱端材料强度提升,柱体承载力和侧移能力均显著改善,因此,采用柱端局部增强的方法改善钢筋混凝土摇摆柱工作性能具有可行性。     

BRIDGE-TOUGHENING ANALYSIS OF THE FIBER REINFORCED COMPOSITE CONTAINING INTERPHASE EFFECT

A detailed fracture mechanics analysis of bridge-toughening in a fiberreinforced composite is presented in this paper.The integral equation governing bridge-toughening as well as crack opening displacement (COD) for the composite withinterfacial layer is derived from the Castigliano's theorem and interface shear-lagmodel.A numerical result of the COD equation is obtained using the iteration solutionof the second Fredholm integral equation.In order to investigate the effect of variousparameters on the toughening,an approximate analytical solution of the equation ispresent and its error analysis is performed,which demonstrates the approximatesolution to be appropriate.A parametric study of the influence of the crack length,interracial shear modules,thickness of the interphase,fiber radius,fiber volumefraction and properties of materials on composite toughening is therefore carried out.The results are useful for experimental demonstration and toughening design includingthe fabrication process of the composite.     

单箱双室组合箱形梁桥静力学特性的研究

为了准确分析单箱双室波纹钢腹板组合箱梁的竖向弯曲力学性能,考虑了组合箱梁的剪力滞、剪切变形、腹板褶皱效应以及剪滞翘曲应力自平衡等因素,设置了3个剪滞纵向翘曲位移差函数,进而基于能量变分法建立了组合箱梁的弹性控制微分方程和自然边界条件。研究表明,褶皱效应对组合箱梁力学性能具有一定影响,且集中荷载下组合箱梁的褶皱效应更为突出;简支边界条件下,组合箱梁剪力滞效应明显,特别是集中荷载组合箱梁的剪力滞效应趋强;本文方法具有一定的理论和工程实用价值,且对该类结构设计具有重要的指导作用。