Influence of Fe-doping on the structural,optical and magnetic properties of ZnO nanoparticles

Zn_1–xFe_xO (x=0–0.05) nanoparticles were synthesized without a catalyst by a two-step method. Fe was doped into ZnO by a source of metallic Fe sheets in a solid–liquid system at 80 °C, and the Zn_1−xFe_xO nanoparticles were obtained by annealing at 300 °C. X-ray diffraction, X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy were used to characterize the structural properties of the as-grown Zn_1−xFe_xO. The optical properties were determined by Infrared and Ultraviolet–visible spectroscopy. The results confirm that the crystallinity of the ZnO is deteriorated due to Fe-doping. XPS results show that there is a mixture of Fe⁰⁺ and the Fe³⁺ in the representative Zn_0.95Fe_0.05O sample. The optical band gap of Zn_1−xFe_xO is enhanced with increasing of Fe-doping. Room temperature ferromagnetism was observed in all the Fe-doped ZnO samples.     

Room temperature magnetism of Fe doped CdS nanocrystals

Undoped and Fe doped CdS nanocrystals with Fe content of 2–5 at% of average crystallite size 1.2–2 nm have been obtained using chemical co-precipitation method with 2-mercaptoethonal as capping agent at 80 °C. X-ray diffraction (XRD) results showed that the undoped CdS nanocrystals were in mixed phase of cubic and hexagonal, where as the doped CdS nanocrystals were in hexagonal phase. Room-temperature ferromagnetism has been observed in Fe-doped CdS nanocrystals. Magnetic studies indicated diamagnetism in undoped, ferromagnetism in lightly doped (2 and 3 at%) and paramagnetism in samples of higher Fe content (4 and 5 at%). The substitutional incorporation of Fe³⁺ ion in Cd²⁺ sites was reflected in structural and electron paramagnetic resonance (EPR) measurements. Isolated as well as interacting Fe³⁺ ions are observed in EPR.     

Effect of thermal treatment in vacuum on Fe-doped SnO2 powders

A sample of 10 at% Fe-doped SnO₂ powder was prepared by mechanical alloying and then thermally treated at 773 K in vacuum. The fit of the diffraction patterns and X-ray absorption spectroscopy measurements revealed that the as milled sample was pure doped rutile. Fe dissolved into SnO₂ was found in Fe²⁺/Fe³⁺ ionic valence with mainly paramagnetic behavior. After the thermal treatment all techniques indicate the formation of the ternary Sn_0.36Fe_2.64O₄ spinel phase, which is responsible for the observed ferromagnetism.     

Mn doped ZnO nanostructured thin films prepared by ultrasonic spray pyrolysis method

Mn-doped ZnO thin films with different percentage of Mn content (0, 1, 3 and 5 at.%) and substrate temperature of 350 °C, were deposited by a simple ultrasonic spray pyrolysis method under atmospheric pressure. We have studied the structural and optical properties by using X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and ultra-violet visible near infrared (UV–Vis-NIR) spectroscopy. The lattice parameters calculated for the Mn-doped ZnO from XRD pattern were found to be slightly larger than those of the undoped ZnO, which indicate substitution of Mn in ZnO lattice. Compared with the Raman spectra for ZnO pure films, the Mn-doping effect on the spectra is revealed by the presence of additional peak around 524 cm⁻¹ due to Mn incorporation. With increasing Mn doping the optical band gap increases indicating the Burstein–Moss effect.     

Growth of Fe-doped ZnO nanorods using aerosol-assisted chemical vapour deposition via in situ doping

In situ Fe doping of ZnO nanorods (NRs) was performed using aerosol assisted chemical vapour deposition (AA-CVD) technique. As the aerosol generator is located outside the reactor, AA-CVD provides the flexibility to control doping parameters, such as doping timing, doping duration and a wider choice of dopant precursors. The Fe dopant aerosol was flowed into the reactor during the growth of ZnO NRs to achieve in situ doping. The X-ray diffraction analysis indicates that the Fe dopants were introduced into the ZnO lattice and present mainly in the form of Fe²⁺. This result is supported by the X-ray photoelectron spectroscopy analysis as the doublet separation is 13.6 eV, although there is a shift of Fe_1/2 and Fe_3/2 peaks to a lower binding energy levels. A strong green emission of PL of Fe-doped ZnO NRs shows that the NRs have poor crystal quality attributed to the Fe-induced defects (recombination centres). The poor photocatalytic performance in degrading Rhodamine B solution of Fe-doped ZnO NRs further proves that the Fe-induced defects were recombination centres rather than traps. Lastly, the growth mechanism of in situ Fe doping of ZnO NRs was discussed.     

Effect of iron doping concentration on magnetic properties of ZnO nanoparticles

The ZnO:Fe nanoparticles of mean size 3-10 nm were synthesized at room temperature by simple co-precipitation method. The crystallite structure, morphology and size estimation were performed by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM). The wurtzite structure of ZnO gradually degrades with the increasing Fe doping concentration. The magnetic behavior of the nanoparticles of ZnO with varying Fe doping concentration was investigated using a vibrating sample magnetometer (VSM). Initially these nanoparticles showed strong ferromagnetic behavior, however at higher doping percentage of Fe, the ferromagnetic behavior was suppressed and paramagnetic nature was observed. The enhanced antiferromagnetic interaction between neighboring Fe-Fe ions suppressed the ferromagnetism at higher doping concentrations of Fe. Room-temperature Mössbauer spectroscopy investigation showed Fe³⁺ nature of the iron atom in ZnO matrix.     

Fabrication of high hole-carrier density p-type ZnO thin films by N-Al co-doping

In order to obtain p-type ZnO thin films, effect of atomic ratio of Zn:N:Al on the electronic and structural characteristic of ZnO thin films was investigated. Hall measurement indicated that with the increase of Al doping, conductive type of as-grown ZnO thin films changed from n-type to p-type and then to n-type again, reasons are discussed in details. Results of X-ray diffraction revealed that co-doped ZnO thin films have similar crystallization characteristic (0 0 2 preferential orientation) like that of un-doping. However, SEM measurement indicated that co-doped ZnO thin films have different surface morphology compared with un-doped ZnO thin films. p-type ZnO thin films with high hole concentration were obtained on glass (4.6 × 10¹⁸ cm⁻³) and n-type silicon (7.51 × 10¹⁹ cm⁻³), respectively.     

Synthesis and optical properties of Co-doped ZnO nanofibers prepared by electrospinning

In this work, Co-doped ZnO nanofibers have been fabricated successfully by an electrospinning technique. The as-prepared nanofibers are characterized by themogravimetric analysis (TG), scanning electron microscopy (SEM), transmission electron microscopy (TEM), powder X-ray diffraction (XRD), Raman spectra and photoluminescence spectroscopy (PL). Results have showed that a wurtzite ZnO nanofibers were obtained and the PL spectrum showed a red-shift by 10 nm due to narrowing of the ZnO band gap (∼3.29 eV) as a result of Co doping. Meanwhile, Raman scattering spectra exhibited an unusual peak at 540 cm⁻¹.     

Cu-doped ZnO nanoparticles: Synthesis, structural and electrical properties

Pure and Cu doped ZnO nanopowders (5, 10, 15, 20, 25 and 30 at% Cu) have been synthesized using co-precipitation method. Transmission Electron Microscopic analysis has shown the morphology of ZnO nanopowders to be quasi-spherical. Powder X-ray Diffraction studies have revealed the systematic doping of Cu into the ZnO lattice up to 10% Cu, though the peaks corresponding to CuO in 10% Cu are negligibly very small. Beyond this level, there was segregation of a secondary phase corresponding to the formation of CuO. Fourier Transform Infrared spectra have shown a broad absorption band at ∼490 cm⁻¹ for all the samples, which corresponds to the stretching vibration of Zn-O bond. DC electrical resistivity has been found to decrease with increasing Cu content. The activation energy has also been observed to decrease with copper doping i.e. from ∼0.67 eV for pure ZnO to ∼0.41 eV for 30 at% Cu doped ZnO.     

Fabrication of p-type Li-doped ZnO films by pulsed laser deposition

p-Type ZnO thin films have been realized via doping Li as acceptor by using pulsed laser deposition. In our experiment, Li₂CO₃ was used as Li precursor, and the growth temperature was varied from 400 to 600 °C in pure O₂ ambient. The Li-doped ZnO film prepared at 450 °C possessed the lowest resistivity of 34 Ω cm with a Hall mobility of 0.134 cm² V⁻¹ s⁻¹ and hole concentration of 1.37 × 10¹⁸ cm⁻³. X-ray diffraction (XRD) measurements showed that the Li-doped ZnO films grown at different substrate temperatures were of completely (0 0 2)-preferred orientation.     

Effects of doping site and pre-sintering time on microstructure and magnetic properties of Fe-doped BaTiO3 ceramics

The A-site substituted BaTiO₃ ceramics were prepared by solid-state reaction via partial substitution of Fe for Ba²⁺. By comparison with the B-site substituted sample made under similar conditions, the effect of Fe doping site on microstructure and magnetism was investigated using X-ray diffraction, Mössbauer spectroscopy and vibrating sample magnetometer. It is found that A-site substitution can be realized to a certain extent at 7 at% Fe addition, whereas impurities are observed at higher Fe concentrations. In the nominal (Ba_0.93Fe_0.07)TiO₃ sample, the Fe ions are present as Fe²⁺ and Fe³⁺, respectively, replacing A-site Ba²⁺ and octahedral B-site Ti⁴⁺ in hexagonal perovskite lattice. The double-exchange Fe²⁺-O²⁻-Fe³⁺ interactions produce ferromagnetism well above room temperature, but the saturation magnetization and the Curie temperature are both obviously lower than those for B-site substitution due to different magnetic exchange mechanisms. In the B-site substituted sample Ba(Ti_0.93Fe_0.07)O₃, the super-exchange interactions between Fe³⁺ on pentahedral and octahedral Ti⁴⁺ sites are responsible for ferromagnetism. These results mean that B-site substitution is a better way for Fe-doped BaTiO₃ system to obtain high-Curie-temperature ferromagnetism. Moreover, increasing pre-sintering time can further improve the magnetism of B-site substituted samples, through which the saturation magnetization for Ba(Ti_0.93Fe_0.07)O₃ is enhanced ∼6 times.     

Effects of annealing ambience on ZnO:N films grown by MOCVD and the p-type doping mechanism of ZnO:N films investigated by XANES

ZnO:N thin films were deposited on sapphire substrate by metal organic chemical vapor deposition with NH₃ as N-doping sources. The reproducible p-type ZnO:N film with hole concentration of ∼10¹⁷ cm⁻³ was successfully achieved by subsequent in situ thermal annealing in N₂O plasma protective ambient, while only weak p-type ZnO:N film with remarkably lower hole concentration of ∼10¹⁵ cm⁻³ was obtained by annealing in O₂ ambient. To understand the mechanism of the p-type doping behavior of ZnO:N film, X-ray photoelectron spectroscopy (XPS) and soft X-ray absorption near-edge spectroscopy (XANES) measurements have been applied to investigate the local electronic structure and chemical states of nitrogen atoms in ZnO:N films.     

Recent developments in the formation and structure of tin-iron oxides by laser pyrolysis

Complex oxides demonstrate specific electric and magnetic properties which make them suitable for a wide variety of applications, including dilute magnetic semiconductors for spin electronics. A tin-iron oxide Sn_1−xFe_xO₂ nanoparticulate material has been successfully synthesized by using the laser pyrolysis of tetramethyl tin-iron pentacarbonyl-air mixtures. Fe doping of SnO₂ nanoparticles has been varied systematically in the 3-10 at% range. As determined by EDAX, the Fe/Sn ratio (in at%) in powders varied between 0.14 and 0.64. XRD studies of Sn_1−xFe_xO₂ nanoscale powders, revealed only structurally modified SnO₂ due to the incorporation of Fe into the lattice mainly by substitutional changes. The substitution of Fe³⁺ in the Sn⁴⁺ positions (Fe³⁺ has smaller ionic radius as compared to the ionic radius of 0.69 Å for Sn⁴⁺) with the formation of a mixed oxide Sn_1−xFe_xO₂ is suggested. A lattice contraction consistent with the determined Fe/Sn atomic ratios was observed. The nanoparticle size decreases with the Fe doping (about 7 nm for the highest Fe content). Temperature dependent ⁵⁷Fe Mössbauer spectroscopy data point to the additional presence of defected Fe³⁺-based oxide nanoclusters with blocking temperatures below 60 K. A new Fe phase presenting magnetic order at substantially higher temperatures was evidenced and assigned to a new type of magnetism relating to the dispersed Fe ions into the SnO₂ matrix.     

Nitrogen-doped ZnO prepared by capillaritron reactive ion beam sputtering deposition

Nitrogen-doped ZnO thin films have been prepared by reactive ion beam sputtering deposition utilizing a capillaritron ion source. X-ray diffraction (XRD) analysis of the as-deposited film exhibits a single strong ZnO (002) diffraction peak centred at 34.40°. Post-growth annealing causes increase of grain size and decrease of c-axis lattice constant. Micro-Raman spectroscopy analysis of the as-deposited film shows strong nitrogen-related local vibration mode at 275, 582, 640 and 720 cm⁻¹, whereas the E₂ mode of ZnO at 436 cm⁻¹ can barely be identified. Annealing at 500-800 °C causes decrease of 275, 582, 640 and 720 cm⁻¹ and increase of 436 cm⁻¹ intensity, indicating out-diffusion of nitrogen and improvement of ZnO crystalline quality. Unlike un-doped ZnO, the surface roughness of nitrogen-doped ZnO deteriorates after annealing, which is also attributed to the out-diffusion of nitrogen. A nitrogen concentration of ∼10²¹/cm³ was observed while type conversion from n-type to p-type was not achieved, which is likely due to the formation of Zn_I-N_O or (N₂)_O that act as donor/double donors.     

Microwave assisted combustion synthesis of CdFe2O4: Magnetic and electrical properties

CdFe₂O₄ particles were synthesized by the microwave assisted combustion method using two different fuels—glycine and urea. Microwave heating provides higher chemical yield within a minute. The synthesized particles were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), ac impedance spectroscopy, vibrating sample magnetometry (VSM) and electron spin resonance (ESR) methods. XRD analysis shows the cubic structure of CdFe₂O₄. The high and low frequency absorption bands of CdFe₂O₄ were found using FTIR analysis. Spherical morphology was revealed from the SEM images. ESR and VSM measurements reveal the antiferromagnetic behavior of CdFe₂O₄. The electrical conductivities of CdFe₂O₄ synthesized using glycine and urea are 6.5×10⁻⁷ S cm⁻¹ and 4.7×10⁻⁸ S cm⁻¹ respectively at 240 ^oC. At elevated temperatures an occurrence of increase in conductivity was observed, which indicates the semiconducting behavior of CdFe₂O₄. The dielectric spectral analysis reveals that dielectric constant of CdFe₂O₄ decreases with frequency and increases with temperature.     

Strong ultraviolet emission from zinc oxide thin films prepared by electrophoretic deposition

In this paper, we report a simple and efficient method to prepare high-quality nanocrystalline ZnO films by electrophoretic deposition. Absorption spectrum and transmission electron microscope image indicated that the average size of ZnO nanoparticles is about 9.5 nm. A strong ultraviolet emission peak at 384 nm is observed and the deep-level emission band is barely observed at room temperature. X-ray diffraction pattern revealed that the ZnO film has a polycrystalline hexagonal wurtzite structure. The Raman spectrum showed a typical resonant multi-phonon process within the ZnO film. The frequency shift of 1 LO phonon was about 583 cm⁻¹.     

Highly conductive and transparent laser ablated nanostructured Al: ZnO thin films

Al doped ZnO thin films are prepared by pulsed laser deposition on quartz substrate at substrate temperature 873 K under a background oxygen pressure of 0.02 mbar. The films are systematically analyzed using X-ray diffraction, atomic force microscopy, micro-Raman spectroscopy, UV-vis spectroscopy, photoluminescence spectroscopy, z-scan and temperature-dependent electrical resistivity measurements in the temperature range 70-300 K. XRD patterns show that all the films are well crystallized with hexagonal wurtzite structure with preferred orientation along (0 0 2) plane. Particle size calculations based on XRD analysis show that all the films are nanocrystalline in nature with the size of the quantum dots ranging from 8 to 17 nm. The presence of high frequency E₂ mode and longitudinal optical A₁ (LO) modes in the Raman spectra suggest a hexagonal wurtzite structure for the films. AFM analysis reveals the agglomerated growth mode in the doped films and it reduces the nucleation barrier of ZnO by Al doping. The 1% Al doped ZnO film presents high transmittance of ∼75% in the visible and near infrared region and low dc electrical resistivity of 5.94 × 10⁻⁶ Ω m. PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. Nonlinear optical measurements using the z-scan technique shows optical limiting behavior for the 5% Al doped ZnO film.     

Structural and magnetic properties of nanocrystalline stannic substituted cobalt ferrite

The structural and magnetic properties of the spinel ferrite system Co_1+xFe_2−2xSn_xO₄ (x=0.0–1.0) have been studied. Samples in the series were prepared by the ceramic technique. The structural and microstructural evolutions of the nanophase have been studied using X-ray powder diffraction and the Rietveld method. The refinement result showed that the type of the cationic distribution over the tetrahedral and octahedral sites in the nanocrystalline lattice is partially an inverse spinel. Far infrared absorption spectra show two significant absorption bands, around 600 cm⁻¹ and 425 cm⁻¹, which are respectively attributed to tetrahedral (A) and octahedral [B] vibrations of the spinel. Scanning Electron Microscopy (SEM) was used to study surface morphology. SEM images reveal particles in the nanosize range. The transmission electronic microscope (TEM) reveals that the grains are spherical in shape. TEM analysis confirmed the X-ray results. The magnetic properties of the prepared samples were characterized by using a vibrating sample magnetometer.     

Effect of iron doping and annealing on structural and optical properties of cerium oxide nanocrystals

Nanocrystalline fluorite-like structures of Ce_1−xFe_xO_2−δ compounds were prepared by chemical precipitation method using cerium chloride and iron chloride as precursors. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and diffuse reflectance spectroscopy (DRS). The effects of iron doping concentration and annealing on particle size, lattice parameter and band gap energies were investigated. The particle size of Fe-doped CeO₂ samples were found to decrease with iron concentration and it increases from 9 to 26 nm as annealing temperature increases to 900 °C.     

Effect of annealing atmosphere on the photoluminescence of ZnO nanospheres

ZnO nanospheres were synthesized by a wet-chemical method. X-ray diffraction and field-emission scanning electron microscopy confirmed the formation of wurtzite-structured ZnO with regular sphere shape. Two Raman modes located at 333 cm⁻¹ and 437 cm⁻¹ with two additional Raman humps centered at 577 cm⁻¹ and 1077 cm⁻¹ were observed. Photoluminescence spectra showed ultraviolet, green, orange and red emissions, which changed significantly after the samples were annealed in air, oxygen, argon and forming gas four different ambiences. All the evidence indicates that surface states are responsible to orange and red emissions in addition to excitonic recombination (3.18 eV) and oxygen vacancy (2.25 eV) emission.