Individual bit island reversal and switching field distribution in perpendicular magnetic bit patterned media

The switching of single bit magnetic islands in bit patterned media (BPM) for two cases with 10 times difference in coercivity, as well as the switching field distribution (SFD) of the islands, has been studied using magnetic force microscopy (MFM) measurements. The intrinsic SFD is measured to be ∼9-11% of the remanence coercivity (H_cr), which contributes only ∼20-50% of the total SFD broadening (∼23-41% of H_cr). High resolution MFM observations clearly showed the influence of surrounding islands on the switching behaviour and switching fields of individual bit islands, resulting in significant contributions in SFD broadening due to non-intrinsic dipolar interactions. It was further observed that single magnetic islands could be switched within a very narrow switching field range as small as 4 Oe, which indicates very sharp and uniform switching for each individual island of BPM.     

Narrow-track perpendicular write heads

Narrow-track perpendicular write heads are reviewed. Because of the strong magnetic interaction between the write head and double-layered medium in perpendicular recording, various types of media are also considered. Current technology is discussed to illustrate design issues; then, for areal densities beyond 1 Tb/in², future technological requirements, including single-pole-type (SPT) heads for discrete track and bit-patterned media, are examined based on numerical simulations.     

Thermally assisted magnetic recording with bit-patterned media to achieve areal recording density beyond 5 Tb/in

Thermally assisted magnetic recording (TAR) with bit-patterned media was investigated by micromagnetic simulation. The media were assumed to be FePt layers. The effective head-field margin as well as the increase in temperature margin and down-track shift margin was investigated. Conditions of the head and medium that lead to a recording density beyond 5 Tb/in² were proposed.     

Design and recording simulation of 1 Tbit/in patterned media

Design of patterned media for an areal density of 1 Tbit/in² with thermal stability is presented based on perpendicular M–H loops of the media. Required perpendicular magnetic anisotropy was estimated to be achieved with known materials. However, it is indicated that magnetostatic interaction between the dots becomes a limiting factor for achieving higher densities. Recording simulation using a Karlqvist pole head on the designed media exhibited possibility of the recording of 1 Tbit/in². Shift margin of the write head in the cross-track direction was found to be increased with elongated dots in the down-track direction. Recording simulation with an FEM-analyzed field of a side-shielded multi-surface pole head exhibited successful recording with increased cross-track shift margins as well as the effect of the elongated dot shape.     

The current status and future of granular media

The current status of CoPtCr-SiO₂ granular media is briefly reviewed, and challenges relative to media technology exceeding 1 Tb/in² are discussed. It is effective to enhance grain isolation using oxide materials that easily precipitate at the grain boundary, and this technique is adopted in commercially available perpendicular recording media. Although some difficulties such as reduction of the grain size retaining the switching field remain, 1 Tb/in² could be achieved by using granular exchange-coupled composite-type media or related technologies. Discrete track media could be used for more than 1 Tb/in² recording. It could also take several years to further develop nano-processing technology and establish a cost-effective infrastructure. BPM offers great potential in achieving high recording density, although some necessary technologies are still too primitive to consider commercial production.     

Optimisation of bit patterned media for 1 Tb/in

Micromagnetic simulations were used to investigate the influence of patterned media geometry on the signal to noise ratio (SNR), adjacent track erasure and write margin for a target recording density of 1 Tb/in². For an ideal patterned medium the readback noise was a maximum when the read head was directly over the dots and a minimum at the transitions. The SNR improved for smaller dots due to the larger dot separation. However, the ideal media with the highest SNR were also the most susceptible to dispersions of dot size and position. Low temperature simulations suggest that large write margins are available; however, at room temperature the write margin can be much reduced. Increasing the rise time of the write head had a deleterious effect on the write margin and the write margin was zero for rise times of more than 0.45 ns. Nevertheless, error-free writing at 1 Tb/in² could be achieved using appropriate head geometries and material parameters.     

Intermediate layer thickness dependence on switching field distribution in perpendicular recording media

The effect of intermediate layer (IL) thickness on crystallographic texture and magnetic properties of CoCrPtSiO₂ granular perpendicular recording media was investigated with switching field distribution (SFD) as the focus. Even though the c-axis orientation of the Co-based recording layer (RL) broadens with the reduction of IL thickness, the SFD becomes narrower. This result demonstrates that the intrinsic SFD is not directly dependent on c-axis orientation of the recording layer but instead dependent on the magnitude of exchange coupling. It is thus possible to have a medium with thin IL and narrow SFD. This is desirable for bit-patterned media (BPM), where highly exchange-coupled grains are required.     

Micromagnetic simulations for terabit/in head/media systems

Bit-patterned (BP) recording is a candidate for extending magnetic data storage towards 10 Tb/in² bit densities. An analysis of the design tolerances is carried out using dynamic micromagnetic simulations and statistical models. The effects of distributions of the magnetic material properties on phase margin and addressability error-rate during writing are investigated. At 1.3 Tb/in² a rapid increase of the error-rate is observed when the write-synchronization deviates from the optimum phase φ₀. Estimates of the fabrication and write-synchronization tolerances are derived from the phase margins. It is shown that the switching-field distribution (from intra-island variations and inter-island interactions) as well as the fabrication and synchronization tolerances must be tightly controlled for Tb/in² applications. At ultra-high densities, BP media may need to be combined with energy-assisted writing, which is referred to as second-generation BP recording.     

Amorphous Ni-Al underlayer-accelerated L10 ordering transition of FePt thin films

In the present study, we succeeded in accelerating the L1₀ ordering transition of FePt thin films by employing amorphous Ni-Al as underlayers. The coercivity H_c = 5 kOe and ordering parameter S = 0.67 of FePt thin films deposited on a Ni-Al underlayer with a thickness of ∼5 nm after 380 °C annealing for 30 min are significantly higher than those H_c = 0.4 kOe and S = 0.35 of the films without the Ni-Al underlayer. The L1₀ ordering process of and the coercivity of FePt thin films can be significantly tuned by varying the thickness of the Ni-Al underlayer.     

Preparation and recording characteristics of granular-type perpendicular magnetic recording media with thin intermediate layer

Granular-type media with thin Ru intermediate layer were prepared on a highly oriented high-B_s FeCo soft underlayer (SUL). A CoPt–TiO₂ recording layer on a Ru intermediate layer of only 2 nm had high-crystal orientation, high H_c of 6.5 kOe, and a high squareness ratio (SQ) of 0.99. The magnetic property of the SUL was also good. The recording performance was measured for the media with different Ru intermediate thicknesses by using a single-pole-type (SPT) head. The media had large reproduced output even for the Ru intermediate layer thickness of 2 nm.     

Thermal stability and switching field of hard/soft-stacked perpendicular media

The time dependence of remanence coercivity and thermal stability were investigated for hard/soft-stacked media consisting of a magnetically hard granular layer underneath a very thin soft layer with a large saturation magnetization, M_s. The values of remanence coercivity at measurement times t′=10³ and 10⁻⁵ s (pulse field) were measured, and defined as H_r and H_r^P. The remanence coercivity on the recording time scale, H_r (1 ns), and the energy barrier, ΔE/kT, were evaluated by fitting H_r and H_r^P to Sharrock's equation taking into account the power law variation of the energy barrier, n. The value of H_r (1 ns) for a (Co–Pt)–SiO₂ (9 nm)/Co–SiO₂ (2 nm) stacked medium with an interfacial coupling control layer was about 9 kOe, which was less than half of that of a (Co–Pt)–SiO₂ (9 nm) conventional medium (=21.3 kOe). The value of ΔE/kT for the stacked medium was about 111 (n=0.7), and was not significantly different from the conventional medium. Moreover, no significant difference in the rate of decrease of H_r with increasing temperature was observed between media with and without interlayers. These results indicate that the use of a thin soft layer with high M_s was effective at significantly reducing H_r with no notable change in thermal stability.     

Recording simulation beyond 2 Tbit/in on bit-patterned media with shielded planar head

A simple technique for bit-patterned media was proposed to increase achievable areal recording densities beyond 2 Tbit/in². Introduction of longitudinal magnetic anisotropy to the media indicated reduced effect of magnetostatic interaction between the dots. Recording simulation with a shielded planar pole head exhibited increased write shift margins in both down and cross track directions compared with that of the perpendicular anisotropy media. It was suggested that recording of an areal density of 2.5 Tbit/in² would be realized with a down and cross track margins of 3.5 and 4.0 nm, respectively. Better recording performance at high areal densities is expected if suitable head could be designed.     

Magnetic properties of Pr-Fe-B/Mn films with perpendicular anisotropy

The influence of a Mn layer on the magnetic properties of sputtered Pr-Fe-B/Mn films with Cu spacer layer has been investigated for various Mn layer thicknesses. The Pr-Fe-B/Mn films all possess perpendicular anisotropy. An enhancement of the intrinsic coercivity _iH_c is observed for suitable Mn layer thickness and _iH_c exhibits an oscillatory dependence on the thickness of the Mn layer with a period of about 60 nm. The average size of the columnar Pr₂Fe₁₄B grains is about 100 nm. A highest _iH_c value of 22.1 kOe and an optimal (BH)_max value of 18.2 MGOe are reported for these Pr-Fe-B/Mn films.     

Patterned media with composite in-plane and perpendicular anisotropy recording layers

Magnetization reversal mechanism in nanostructures composed of exchange coupled bi-layers with in-plane and perpendicular anisotropy was investigated. Micromagnetic simulation was carried out for bit-patterned media with areal density of 5 Tb/in², as example. Magnetization of thermally stable recorded bit using a single layer may not switch under write field. However, a complete and fast switching is possible with an exchange coupling to a layer with in-plane anisotropy. By adjusting the thicknesses and intrinsic properties of the two layers, the composite recording layer still can retain perpendicular anisotropy. The exchange coupled structure with dual-anisotropy can be extended to magnetic memories.     

Enhancement of coercivity with reduced grain size in CoCrPt film grown by pulsed laser deposition

We report a pulsed laser deposition (PLD) growth of VMn/CoCrPt bilayer with a magnetic coercivity (H_c) of 2.2 kOe and a grain size of 12 nm. The effects of VMn underlayer on magnetic properties of CoCrPt layer were studied. The coercivity, H_c, and squareness, S, of VMn/CoCrPt bilayer, is dependent on the thickness of VMn. The grain size of the CoCrPt film can also be modified by laser parameters. High laser fluence used for CoCrPt deposition produces a smaller grain size. Enhanced H_c and reduced grain size in VMn/CoCrPt is explained by more pronounced surface phase segregation during deposition at high laser fluence.     

Numerical simulation of magnetic interactions in polycrystalline YFeO3

The magnetic behavior of polycrystalline yttrium orthoferrite was studied from the experimental and theoretical points of view. Magnetization measurements up to 170 kOe were carried out on a single-phase YFeO₃ sample synthesized from heterobimetallic alkoxides. The complex interplay between weak-ferromagnetic and antiferromagnetic interactions, observed in the experimental M(H) curves, was successfully simulated by locally minimizing the magnetic energy of two interacting Fe sublattices. The resulting values of exchange field (H_E=5590 kOe), anisotropy field (H_A=0.5 kOe) and Dzyaloshinsky–Moriya antisymmetric field (H_D=149 kOe) are in good agreement with previous reports on this system.     

Synthesis and surface modified hard magnetic properties in Co0.5Pt0.5 nanocrystallites from a rheological liquid precursor

Small crystallites of a metastable phase Co_0.5Pt_0.5 are precipitated by heating a rheological liquid precursor of cobalt–hydrazine complex and platinum chloride H₂PtCl₆·xH₂O in polymer molecules of poly(vinylpyrrolidone) (PVP) in ethylene glycol. The hydrazine co-reduces nascent atoms from the Co²⁺ and Pt⁴⁺ that recombine and grow as Co_0.5Pt_0.5. The PVP molecules cap a growing Co_0.5Pt_0.5 as it achieves a critical size so that it stops growing further in given conditions. X-ray diffraction pattern of a recovered powder reveals a crystalline Co_0.5Pt_0.5 phase (average crystallite size D∼8 nm) of a well-known Fm3m-fcc crystal structure with the lattice parameter a=0.3916 nm (density ρ=14.09 g/cm³). A more ordered L1₀ phase (ρ=15.91 g/cm³) transforms (D≥25 nm) upon annealing the powder at temperature lesser than 700 °C (in vacuum). At room temperature, the virgin crystallites bear only a small saturation magnetization M_s=5.54 emu/g (D=8 nm) of a soft magnet and it hardly grows on bigger sizes (D≤31 nm) in a canted ferromagnetic structure. A rectangular hysteresis loop is markedly expanded on an optimally annealed L1₀ phase at 800 °C for 60 min, showing a surface modified coercivity H_c=7.781 kOe with remnant ratio M_r/M_s=0.5564, and M_s=39.75 emu/g. Crystallites self-assembled in an acicular shape tailor large H_c from ideal single domains and high magnetocrystalline anisotropy of a hard magnet L1₀ phase.     

Effect of continuous layer in CGC perpendicular recording media

The effect of continuous layer on CoCrPt–SiO₂ granular layer is studied in coupled granular continuous (CGC) perpendicular recording media. In the cross-section transmission electron microscope (TEM) observation, magnetic grain in the granular layer shows columnar structure, while Co/Pd multilayer shows continuous layer. The plane-view TEM image of the granular layer shows well-isolated grain structure with average grain size of around 6 nm, and grain-to-grain separation width of around 2 nm. Therefore, the interactions among the grains are negligible (J∼0). By depositing a continuous layer on a CoCrPt–SiO₂ granular layer, the grains in the granular layer are magnetically coupled through capping layer that leads to the suppression of magnetic anisotropy dispersion. This CGC structure reduces the coercivity dispersion (Δ_Hc/_Hc$\mathrm{\Delta }{H}_{\mathrm{c}}/H_{\mathrm{c}}$) from 0.26 to 0.15 and saturation field (H_s) from 10.4 to 6.7 kOe. The reduction of H_s and Δ_Hc/_Hc$\mathrm{\Delta }{H}_{\mathrm{c}}/H_{\mathrm{c}}$ improves the OW by 21.3 dB. The small Δ_Hc/_Hc$\mathrm{\Delta }{H}_{\mathrm{c}}/H_{\mathrm{c}}$ also maintains SNR of CGC media with strong magnetic exchange coupling. Furthermore, the coupling of grains through continuous layer enlarges the magnetic nucleation field (H_n) from 0.4 to −1.7 kOe. Consequently, CGC media shows better thermal stability compared to non-CGC media.     

Magnetostriction of TbxHo0.75−xPr0.25(Fe0.9B0.1)2 (x=0–0.3) compounds

The Tb_xHo_0.75−xPr_0.25(Fe_0.9B_0.1)₂ (x=0, 0.1, 0.15, 0.2, 0.25, and 0.3) compounds are found to stabilize in a cubic Laves phase structure. The lattice parameter, magnetostriction (at 10 kOe), and Curie temperature are found to increase with increasing Tb content. The compound with x=0.15 exhibits a possible anisotropy compensation between the Tb and (Ho/Pr) sublattices. The easy magnetization direction rotates towards the 〈1 1 1〉 from the 〈1 0 0〉 direction, with increasing Tb content. The splitting of the (4 4 0) peak accompanied by the spontaneous magnetostriction-induced rhombohedral distortion is observed for compounds with x?0.15 and the spontaneous magnetostriction (λ_1 1 1) is found to increase with Tb content.     

Micromagnetic studies for bit patterned media above 2 Tbit/in.

Bit patterned media (BPM) recording is a candidate for extremely high density magnetic recording. A micromagnetic model is built up to analyze the phase diagram of the correct-write-in condition in BPM above 2 Tb/in.² fabricated by lithography or ion irradiation methods. The target of the study is to acquire the relationship between the recording performance and the magnetic properties of the media. The medium includes the polycrystalline grains and grain boundary. In BPM fabricated by lithography with FCT structure, two phase diagrams of the correct-write-in condition are found for the anisotropy angular distribution Δθ, the ratio of tetragonal anisotropy K₂₂ to uniaxial anisotropy K₁ and the uniaxial anisotropy distribution ΔK₁. In BPM fabricated by ion irradiation methods, two phase diagrams of the correct-write-in condition are analyzed for the ratio of saturation magnetization M′_s/M_s, anisotropy field H′_k/H_k and the exchange field H′_ex/H_ex in the ion irradiated region and the bit islands.