砂磨法制备聚苯胺及其电化学性能的研究

首次采用砂磨法制备了导电态聚苯胺(PANI), 通过循环伏安和电导率的测试分析, 探讨了转速(N)、反应时间(t)、盐酸(HCl)浓度、十二烷基苯磺酸钠(SDBS)浓度和过硫酸铵(APS)浓度对产物氧化还原性及导电性能的影响|并采用红外光谱(FT-IR)对产物结构进行了表征. 结果表明: 当N为400 r/min, t为2 h, HCl与苯胺(An)的摩尔比(n_HCl/n_An)为4∶1, SDBS与An的摩尔比(n_SDBS/n_An)为1∶1, APS与An的物质的量比(n_APS/n_An)为0.8∶1时, 产物的各项性能达到最佳值|且砂磨法与乳液法制备的PANI结构相符, 电化学性能接近, 但是砂磨法的生产成本和环保优势十分显著(砂磨法的反应时间仅为乳液法的1/3, 用水量仅为乳液法的1/2).     

表面活性剂辅助合成LiNi0.8Co0.1Mn0.1O2正极材料

通过添加烷基季铵盐类表面活性剂来调控材料形貌和粒径的改性方法,在LiNi_0.8Co_0.1Mn_0.1O₂前驱体合成过程中添加表面活性剂十二烷基三甲基溴化铵(DTAB)和十六烷基三甲基溴化铵(CTAB),利用尿素作为配合剂和沉淀剂,采用溶剂热法合成LiNi_0.8Co_0.1Mn_0.1O₂前驱体。最后,高温混锂煅烧合成椭球形的空心多孔材料。相比于不添加表面活性剂的样本,改性的材料有着更小的粒径和更加规整的形貌。电化学测试表明,添加DTAB和CTAB之后,首次充电容量分别达到223与251 mAh·g^-1(0.1C)。其中,添加CTAB的样品首次放电容量达到216 mAh·g^-1(0.1C),100次循环后容量保持率为85.1%,高于LiNi_0.8Co_0.1Mn_0.1O₂的81.7%(0.1C)。表面活性剂的改性显著提高了材料的电化学性能,为高镍三元正极材料的改性提供了一种新的思路。     

镝掺杂铁氧体纳米晶的制备、表征和磁性

采用化学共沉淀法制备出了镝掺杂铁氧体纳米晶, 利用透射电子显微镜(TEM)、X射线衍射仪(XRD)、傅立叶红外光谱仪(FTIR)、古埃磁天平、振动样品磁强计(VSM)、X射线能谱仪(EDX)等仪器对产物进行了表征, 研究了Dy^3＋掺杂量对铁氧体纳米晶的结构、磁性和粒度的影响. 结果表明: 适量稀土元素镝离子的掺杂可以提高尖晶石型铁氧体的磁性、降低矫顽力, 当n(Fe^3＋)∶n(Dy^3＋)＝14∶1时其磁性最强. Dy^3＋替代或充填进入了尖晶石晶格, 且主要占据B位. 掺杂了镝的铁氧体磁性纳米粒子粒度变小, 且分布更集中、均匀, 当Dy^3＋加入量为n(Fe^3＋)∶n(Dy^3＋)＝14∶1时铁氧体纳米粒子的平均粒径由掺杂前的14 nm降低到到8 nm. 这种具有超顺磁性的软磁铁氧体纳米晶可应用于纳米磁液领域.     

供体-锯齿型碳纳米管-受体的非线性光学响应对管径的依赖性

用密度泛函 B3LYP 方法得到一系列不同管径的氨基-硝基双取代纳米管NH₂-(n,0)CNT-NO₂ (n＝5～10)的几何结构. 用CAM-B3LYP 方法计算了体系的第一超极化率(β₀). 研究表明, β₀ 对管径大小有着极强的依赖性. 特别是对偶数纳米管(n＝6, 8 和10), 其β₀ (5.5×10³～9.8×10⁴ au)是奇数纳米管β₀ (1.0×10³～2.8×10³ au)的5～35 倍.     

二价双核铀聚吡咯配合物结构设计和铀-铀多重键的理论研究

经三十余年努力,二价铀溶液化学于近年取得突破性进展,Evans和Meyer等成功获得两个可通过X-ray晶体衍射表征结构的有机金属铀（II）配合物.为进一步拓展U^II配合物化学和探索可能存在的金属多重键,设计双核配合物[（U^II）₂（L）]（L为八齿氮供体低聚吡咯大环四价阴离子）,并使用相对论密度泛函理论优化其可能的电子自旋态异构体结构和计算相关性质.结果表明,[（U^II）₂（L）]具有三重态基态,其电子组态为π⁴σ²δ²;U（5f）原子轨道对高占据分子轨道有重要贡献;它的U-U键长为2.33Å、Mayer键级为3.89和对应的伸缩振动频率为259 cm^-1,被指认为U-U弱四重键.这一结论与QTAIM （quantum theory of atoms in molecule）的U-U键临界点处的电子/能量密度拓扑分析结果相一致.与不同氧化态铀同类物[（U^m）₂（L）]ⁿ⁺ （m=III,n=2;m=IV,n=4）比较显示,随着铀氧化态增大,U-U距离增长、键级变小、伸缩振动频率变小,金属铀电子自旋密度与常规预期值的差值（?S_U）增大;结合分子轨道和QTAIM参数分析,发现金属氧化态可以调控配体和金属轨道能级匹配程度和改变金属-金属多重键.     

三氟丙基修饰的有机-无机杂化二氧化硅膜制备、氢气分离及水热稳定性能

以三氟丙基三甲氧基硅烷(TFPTMS)和1,2-双(三乙氧基硅基)乙烷(BTESE)为前驱体, 通过溶胶-凝胶法在酸性条件下制备三氟丙基修饰的有机-无机杂化SiO₂膜材料, 并深入研究三氟丙基修饰对溶胶粒径和疏水性能的影响以及膜材料的氢气渗透分离性能和长期水热稳定性. 结果表明三氟丙基已成功修饰到有机-无机杂化SiO₂膜材料中, 且随着TFPTMS修饰量的增加, 溶胶粒径有减小趋势, 膜材料的疏水性能逐渐提高. 当n(TFPTMS)/n(BTESE)＝0.6时, 溶胶平均粒径为2.11 nm, 膜材料对水的接触角达到111.6°±0.7°. H₂在修饰后膜材料中的输运主要遵循微孔扩散机理, 300 ℃时H₂的渗透率为8.86×10^-7 mol·m^-2·s^-1·Pa^-1, H₂/CO₂的理想分离系数达到5.4, 且当进气摩尔比例为1∶1时H₂/CO₂的双组分气体分离系数达到了4.82, 均高于Knudsen扩散分离因子(H₂/CO₂＝4.69), 膜材料呈现出良好的分子筛分性能. 膜材料在250 ℃及水蒸气摩尔含量为5%的水热环境中能稳定工作300 h以上.     

替米考星磁性表面分子印迹聚合物的制备及应用

报道了一种替米考星磁性表面分子印迹聚合物吸附剂。它以Fe₃O₄@SiO₂为磁性基质，替米考星为模板分子，甲基丙烯酸为功能单体，通过硅烷化反应在Fe₃O₄@SiO₂表面键合上3-（甲基丙烯酰氧）丙基三甲氧基硅烷制备得到。该吸附剂对大环内酯类抗生素表现出高选择性和高富集能力（对4种模型大环内酯的富集倍数为212~675倍）。相比传统的非表面分子印迹聚合物，吸附平衡时间可缩短为30 min，可以重复使用至少6次；结合高效液相色谱-紫外检测，将该吸附剂应用于奶粉中4种大环内酯类抗生素的残留检测，所得检出限和定量限分别为0.58~1.36 μg/kg和1.92~4.55 μg/kg，日内（n=5）和日间（n=3）回收率在83.2%~123.0%之间，RSD均小于12.2%。     

调控金纳米花表面凸起的策略及其表面增强拉曼散射活性

以聚乙烯吡咯烷酮(PVP)与十二烷基硫酸钠(SDS)通过阳离子架桥形成的拟聚阴离子为软模板,通过改变PVP、SDS和纳米材料前驱体氯金酸(HAu Cl₄)浓度以及反应时间等因素,调控还原产物金纳米花形貌及粒径。表面张力、电导率、毛细管电泳及Zeta电位等实验结果表明PVP-SDS-HAu Cl₄形成新的拟聚阴离子,透射电子显微镜和X射线衍射结果表明SDS、PVP和HAu Cl₄的较低浓度组合更易获得表面凸起丰富的金纳米花。PVP-SDS拟聚阴离子发挥了二级软模板作用,在PVP (50 g·L^-1)-SDS (2 mmol·L^-1)-HAu Cl₄ (0.25 mmol·L^-1)溶液中调控合成的金纳米花为{111}晶面为主的面心立方结构,其平均等效粒径为108 nm,且表面上密集分布约16.5 nm的凸起。该金纳米花有较强的表面增强拉曼散射(SERS)活性,探针分子罗丹明6G的SERS信号强度依赖于金纳米花的表面凸起形貌。该研究中金纳米...     

功能性离子液体萃取水溶液中Cu2+:实验与理论

本工作针对含硫脲基咪唑憎水功能离子液体在溶液中Cu²⁺萃取方面的应用及其机理进行研究. 考察了萃取两相体积比、金属离子浓度、时间、无机盐NaCl、溶液pH及离子液体烷基链长等因素的影响. 结果表明: 室温条件下, 0.1 mL离子液体[C_nMPSM][PF₆] (n=4、6、8)与5 mL 21.94 mg/L的氯化铜溶液室温条件下超声混合30 min, 溶液中Cu²⁺的去除率即超过95%; 且此类离子液体对金属离子的萃取效果顺序为: n=4≈n=6>n=8. 以[HMPSM][PF₆]为研究对象, 发现溶液中无机盐NaCl的含量以及溶液pH 对金属离子的萃取效果影响不明显. 与传统离子液体[C_nbim][PF₆] (n=6、8)相比, 硫脲基的引入使其萃取率由20%左右提高到99%, 且有效避免因阳离子交换而引起水中咪唑阳离子含量增加问题. 通过理论计算发现, 功能离子液体对金属离子的萃取依赖于官能团中的S元素与Cu²⁺之间较强的静电及路易斯酸碱作用, 与萃取实验中离子液体未和Cu²⁺发生阳离子交换作用相吻合.     

Pd/C催化剂用于CO2电化学还原生成CO:Pd载量的影响

CO₂电化学还原反应可以将CO₂转化为燃料并同时实现再生能源的有效存储. 目前纳米结构的多相催化剂已经广泛应用于此反应,其中碳负载钯纳米粒子（Pd/C）表现出优异的CO₂电化学还原性能. 本工作研究了钯载量对于Pd/C催化剂结构以及其催化CO₂还原生成CO反应活性和选择性的影响. 不同载量的Pd/C催化剂通过液相还原方法制备,钯纳米粒子均匀地分散在碳载体上,载量并没有明显改变对纳米粒子的粒径. 在优选的电解质（0.1 mol·L^-1 KHCO₃）中,CO法拉第效率与载量呈现火山型曲线关系,-0.89 V时载量为20wt%的Pd/C催化剂达到最高的CO法拉第效率(91.2%). 生成CO的几何电流密度随着钯载量的增加而增加,但CO转换频率具有相反的趋势,载量为2.5wt%的Pd/C催化剂具有最高的转换频率. 这种载量对CO₂电化学还原反应活性和选择性的影响主要由活性位的数量、反应动力学、中间物种的稳定性以及反应物、中间物种和产物的传质过程等共同决定.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.