Ag/TiO2纳米材料的制备和光致变色性能研究

 采用光催化还原法在不同温度热处理的TiO2薄膜表面沉积Ag纳米颗粒,制备了Ag/TiO2纳米薄膜材料。通过UV-Vis吸收光谱表征对比了不同温度热处理的TiO2对Ag粒子光催化沉积的影响,发现500℃退火处理TiO2薄膜较利于Ag纳米粒子的光催化沉积;在650 nm红色激光照射下,500℃退火处理的Ag/TiO2样品具有明显的光致变色现象,对此变色过程中涉及的机理进行了讨论,且发现随着Ag纳米颗粒光催化沉积时间的增长,Ag/TiO2薄膜光致变色的响应速率提高,但Ag纳米颗粒过多会抑制Ag/TiO2薄膜的变色响应速率。     

Au/SiO2纳米多层薄膜的制备及其性质表征

利用多靶磁控溅射技术制备了Au/SiO₂纳米颗粒分散氧化物多层复合薄膜.研究了在保持Au单层颗粒膜沉积时间一定时薄膜厚度一定、变化SiO₂的沉积时间及SiO₂的沉积时间一定而改变薄膜厚度时，多层薄膜在薄膜厚度方向的微观结构对吸收光谱的影响.研究结果表明：具有纳米层状结构的Au/SiO₂多层薄膜在560 nm波长附近有明显的表面等离子共振吸收峰，吸收峰的强度随Au颗粒的浓度增加而增强，在Au颗粒浓度相同的情况下，复合薄膜 关键词： 2纳米复合薄膜')" href="#">Au/SiO₂纳米复合薄膜 多靶磁控溅射 吸收光谱 有效介质理论     

脉冲激光沉积Ag:BaTiO3纳米复合薄膜及其光学特性

在MgO(100)基片上利用脉冲激光沉积技术制备了掺有Ag纳米颗粒的BaTiO₃复合薄膜.通过X射线衍射对薄膜的结构进行了表征,利用透射电子显微镜对Ag纳米颗粒的尺寸、形态进行了观测,X射线光电子能谱结果表明Ag呈金属态.在410—500nm范围内观测到了Ag纳米颗粒引起的等离子振荡峰,随着后处理温度和Ag颗粒浓度的增加,吸收峰发生红移,并出现了双峰现象. 关键词： 金属纳米复合薄膜 激光沉积 光吸收     

脉冲激光沉积Ag:BaTiO3纳米复合薄膜及其光学特性

在MgO(100)基片上利用脉冲激光沉积技术制备了掺有Ag纳米颗粒的BaTiO3复合薄膜.通过X射线衍射对薄膜的结构进行了表征,利用透射电子显微镜对Ag纳米颗粒的尺寸、形态进行了观测,X射线光电子能谱结果表明Ag呈金属态.在410-500 nm范围内观测到了Ag纳米颗粒引起的等离子振荡峰,随着后处理温度和Ag颗粒浓度的增加,吸收峰发生红移,并出现了双峰现象.     

不同厚度溅射Ag膜的微结构及光学常数研究

用直流溅射法在室温Si基片上制备了4．9nm-189.0nm范围内不同厚度的Ag薄膜，并用X射线衍射及反射式椭偏光谱技术对薄膜的微结构和光学常数进行了测试分析。结构分析表明：制备的Ag膜均呈多晶状态，晶体结构仍为面心立方；随膜厚增加薄膜的平均晶粒心潮6．3nm逐渐增大到14．5nm；薄膜晶格常数均比标准值（0．40862nm)稍小，随膜厚增加，薄膜晶格常数由0．40585nm增大到0.40779nm。250nm-830nm光频范围椭偏光谱测量结果表明：与Johnson的厚Ag膜数据相比，我们制备的Ag薄膜光学折射率n总体上均增大，消光系数k变化复杂；在厚度为4．9nm-83.7nm范围内，实验薄膜的光学常数与Johnson数据差别很大，厚度小于33．3nm的实验薄膜k谱线中出现吸收峰，峰位由460nm红移至690nm处，且其对应的峰宽逐渐宽化；当膜厚达到约189nm时，实验薄膜与Johnson光学常数数据已基本趋于一致。     

光电变色器件用纳米晶氧化钛薄膜的微结构与特性

纳米晶TiO2薄膜在光电变色器件中具有很重要的作用。它的微结构直接影响染料的吸附、光的散射以及电荷输运的特性。因此，探索TiO2薄膜的微结构(如粒径、表面形貌和厚度等)及光电性能是非常有意义的。采用电子束蒸发工艺制备了光电变色器件用纳晶TiO2薄膜，利用原子力显微镜、X射线衍射、俄歇电子能谱等手段对纳米晶TiO2薄膜的表面形貌、结晶状态及组分进行了分析。从理论上研究和讨论了纳米晶TiO2薄膜晶粒尺寸对光电性能的影响，并用量子限制效应解释了吸收光谱峰值波长随粒径减小而发生蓝移的现象。     

Au/SiO2纳米多层薄膜的制备及其性质表征

利用多靶磁控溅射技术制备了Au/SiO2纳米颗粒分散氧化物多层复合薄膜.研究了在保持Au单层颗粒膜沉积时间一定时薄膜厚度一定、变化SiO2的沉积时间及SiO2的沉积时间一定而改变薄膜厚度时,多层薄膜在薄膜厚度方向的微观结构对吸收光谱的影响.研究结果表明:具有纳米层状结构的Au/SiO2多层薄膜在560nm波长附近有明显的表面等离子共振吸收峰,吸收峰的强度随Au颗粒的浓度增加而增强,在Au颗粒浓度相同的情况下,复合薄膜光学吸收强度随薄膜厚度的增加而增强.但当金属颗粒的浓度增加到一定程度时,金属颗粒相互接触,没有观察到纳米层状结构,薄膜不显示共振吸收峰特征.用修正后的M-G(Maxwell-Garnett)理论对吸收光谱进行了模拟,得到了与实验一致的结果.     

中空Ag纳米球壳的制备及性能表征

 以改性聚苯乙烯微球为模板,采用化学镀法在聚苯乙烯微球表面包覆一层银,在四氢呋喃溶液中将聚苯乙烯微球溶解,得到中空Ag纳米球壳。采用扫描电镜、透射电镜和X射线衍射仪对样品进行了表征及分析,并用紫外可见分光光度计研究了粒子的光学性质。实验结果表明：运用此法成功地制备出中空Ag纳米球壳的内径为250 nm,壁厚约为15 nm,并且成功地使纳米粒子的紫外吸收光谱由600 nm红移至900 nm左右,实现了在可见光至近红外光区调节Ag纳米结构的吸收峰。     

掺Ag纳米颗粒的BaTiO3复合薄膜的非线性光学特性

通过准分子激光(XeCl,308 nm,20 ns)在MgO(100)单晶衬底上制备了不同掺杂浓度的Ag:BaTiO3纳米复合薄膜,通过X射线衍射和X射线光电子能谱对薄膜的结构和组分进行了表征.在430 nm和470 nm附近观测到了不同浓度Ag纳米颗粒引起的等离子体吸收峰,通过z扫描技术对复合薄膜的三阶非线性光学特性进行了测量,并对其光学非线性的增强机制进行了讨论.     

(Au,Ag)/Si复合纳米颗粒薄膜的微结构与光谱特性

采用复合靶共溅射方法制备了(Au,Ag)/Si复合纳米颗粒薄膜,分别采用Maxwell-Garnett理论和微分有效媒质(DEM)理论计算了Ag/Si复合薄膜的吸收光谱,实验测量结果与DEM理论计算更接近,讨论了(Au,Ag)/Si体系复合薄膜共振吸收峰宽化的微观机制. 关键词：     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.