单油酸三羟甲基丙烷酯改性水性聚氨酯

利用单油酸三羟甲基丙烷酯(TMPM)、异佛尔酮二异氰酸酯(IPDI)和聚氧化丙烯(PPG)等制备水性聚氨酯。采用透射电镜(TEM)、动态激光光散射(DLLS)、红外光谱(FT-IR)、热重分析(TGA)和表面张力仪表征了乳液胶束形态、产物结构及性能。结果表明:水性聚氨酯(PU)分子上引入脂肪侧链容易在水中形成规整的胶束,但TMPM改性的水性聚氨酯胶束粒径随TMPM含量的增加不断增大,当w(TMPM)=0.07时,乳液不稳定;脂肪侧链的引入降低了水性聚氨酯乳液的表面张力,表面张力随着反应体系中—NCO和—OH摩尔比的增大而降低,随交联度的增大先增加后减小;TMPM的引入可以提高胶膜的热稳定性。     

侧链为光敏感基团的可生物降解聚氨酯的合成及表征

设计合成2-甲基-2-肉桂酰氧甲基-1,3-丙二醇(MCO)作为扩链剂,并以聚乳酸二醇(PLA diol)为软段,异佛尔酮二异氰酸酯(IPDI)和MCO为硬段制备了一系列侧链含有肉桂基团的可生物降解聚氨酯.结果表明MCO具有较高的反应活性,可满足制备高分子量聚氨酯的要求.聚氨酯结构中的肉桂双键可在紫外光和光引发剂的共同作用下,发生快速的交联反应,短时间内形成交联结构.软段结构相同时,凝胶含量随MCO含量的增加而增加.硬段结构相同时,凝胶含量随软段分子量的增加而减少.适度的交联可提高拉伸强度和形变回复率.     

氨基硅油扩链改性水性聚氨酯的合成及性能研究

采用甲苯二异氰酸酯(TDI)、聚氧化丙烯二醇(PPG)、2,2-二羟甲基丙酸(DMPA)为原料,先制备成聚氨酯预聚体,再通过在乳化过程中以侧链氨基硅油(AEAPS)或直链氨基硅油(ATPS)扩链制得了一系列水性聚氨酯乳液,并对涂膜的红外光谱、耐水性、力学性能和表面疏水性等进行了研究。结果表明,通过氨基硅油改性的聚氨酯涂膜,在保持力学性能基本不变的情况下,其耐水性、表面疏水性等性能都有明显提高。其中,侧链氨基硅油(AEAPS)比直链氨基硅油(ATPS)具有更好的改性效果。     

水性丙烯酸酯聚氨酯涂料的研究

合成了含羟基的丙烯酸酯树脂,并与甲苯二异氰酸酯反应制备预聚体Ⅰ,Ⅰ与扩链剂二羟甲基丙酸反应得到含羧基的预聚体Ⅱ,最后用1,4-丁二醇交联,制得水性丙烯酸酯聚氨酯涂料,讨论了合成过程中影响乳液稳定性和涂膜性能的因素。测试结果表明：涂膜的强度、光泽、硬度等性能均优于传统的同类树脂。     

有机磷阻燃改性水性聚氨酯

以聚醚(N-210)、异佛尔酮二异氰酸酯(IPDI)为基本单体,[(双(2-羟乙基)氨基)甲基]磷酸二乙酯(FRC-6)、一缩二乙二醇(EX)为扩链剂,二羟甲基丙酸(DMPA)为亲水扩链剂,3-(2-氨乙基)氨丙基甲基二甲氧基硅烷(KH-602)为后扩链剂,合成了一系列有机磷(P)阻燃改性的水性聚氨酯乳液。研究表明:随着FRC-6用量的增加,聚氨酯(PU)的起始热分解温度降低,但热释放速率也降低,而PU的阻燃性能得到很大的提高。当FRC-6中P的含量占预聚体的质量分数为2.31%时,其氧指数为28%,垂直燃烧测试显示PU的阻燃性能已达到UL-94V-2级。     

GHD室温自交联乳液的聚合及贮存稳定性

采用半连续种子乳液聚合技术合成了含甲基丙烯酸缩水甘油酯(GMA)、甲基丙烯酸羟乙酯(HEMA)和甲基丙烯酸二甲氨基乙酯(DMAEMA)的室温自交联乳液(GHD).实验结果表明,在甲基丙烯酸甲酯(MMA)-丙烯酸丁酯(BA)-GMA种子乳液存在下,聚合温度升高,聚合过程稳定性下降,但乳液的贮存稳定性提高;乳化单体滴加速度加快,种子聚合物的玻璃化温度升高,可减少聚合过程的交联凝聚作用,提高聚合过程的稳定性;而HEMA和DMAEMA用量增加对聚合过程的稳定性没有明显影响,但使乳液的贮存稳定性下降.官能团间的交联凝聚作用可能是影响室温自交联乳液聚合及贮存过程稳定性的关键因素.     

酚氧树脂／蓖麻油交联聚氨酯

使2.2-(4’-羟基苯基)丙烷(双酚A)与环氧氯丙烷反应制得了带端羟基的酚氧树脂(HBA),将其与蓖麻油共混,用2.4-甲苯二异氰酸酯(TDI)作固化剂,制得了一系列交联聚氨酯。DSC和DMA测试结果表明,这种聚氨酯只有一个T_g。改变NCO/OH摩尔比及HBA/(HBA 蓖麻油)比可制得具有较好阻尼性能的聚氨酯材料。     

四甲基苯二甲基二异氰酸酯基水性聚氨酯的合成和性能

采用四甲基苯二甲基二异氰酸酯、聚酯二元醇和二羟甲基丙酸为原料,合成了一系列具有不同异氰酸根与羟基摩尔比（n(-NCO)/n(-OH)）的聚氨酯乳液。 研究了n(-NCO)/n(-OH)对水性聚氨酯性能的影响。 结果表明,当该比值增加时,乳液的粒径增大,分布变宽,结晶性降低,耐热性下降,耐水性能呈现降低的趋势。 当异氰酸根与羟基摩尔比为3时,四甲基苯二甲基二异氰酸酯基水性聚氨酯的乳液粒径为10～30 nm,膜的分解温度达到275 ℃,24 h吸水率低于10%。     

水性聚氨酯/纳米TiO2复合乳液制备及其抗菌性能的研究

以佛尔酮二异氰酸酯(IPDI)、聚丙二醇(PPG)和改性纳米TiO2为主要原料,二羟甲基丙酸(DMPA)为亲水扩链剂和乙二胺(EDA)为小分子扩链剂,通过原位分散聚合方法制备了水性聚氨酯/纳米TiO2复合乳液。考察了改性纳米TiO2用量对复合乳液粘度、粒径及稳定性的影响。结果表明,复合乳液具有一定的紫外吸收能力和良好的抑菌作用,抑菌性能随纳米TiO2含量的增加而提高。     

PCDL型超支化水性聚氨酯的合成与性能

以甲苯-2,4-二异氰酸酯（TDI）、聚碳酸酯二醇（PCDL）、二羟甲基丙酸（DMPA）和二乙醇胺（DEOA）为原料,采用A₂＋bB₂共聚合路线合成了具有超支化结构的水性聚氨酯（HBAPU）乳液。采用红外光谱（FT-IR）、核磁共振（13C NMR）对产物结构进行了表征,证实了超支化聚氨酯的支化度随 n(NCO)/n(OH)比值的增大而增大。用PCS、TG、电子拉力机对产物的性能进行了测试,同时也对胶膜的耐水性进行了测试,发现在DMPA含量为0.4 mmol/g时,HBAPU的粒径仅有20.57 nm,而线性水性聚氨酯粒径有130.91 nm,并且HBAPU具有良好的耐水性、热稳定性和较高的拉伸强度。     

Physical properties of glycosaminoglycan hydrogels

The chemical composition of glycosaminoglycan (GAG) hydrogels was found to have a profound effect on the physical properties of gels. Hyaluronan (HA) and chondroitin sulfate (CS) were each modified with adipic dihydrazide (ADH) with carbodiimide chemistry. The resulting polymer was crosslinked with various concentrations of poly(ethylene glycol) dialdehyde (PEG‐diald) to produce a series of hydrogels. The physical properties of these GAG hydrogels varied in a concentration‐dependent fashion. Maximal crosslinking was observed at a theoretical crosslinking of 50% for the HA‐ADH‐PEG‐diald hydrogels and 75% for the CS‐ADH‐PEG‐diald hydrogels. Adding PEG‐diald beyond the optimum for crosslinking prolonged the in vitro enzymatic degradation time of the hydrogels. The swelling of the crosslinked GAG hydrogels was correlated with the amount of PEG‐diald used rather than with the crosslinking density. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4344–4356, 2004     

Synthesis and properties of room temperature curable trimethoxysilane‐terminated polyurethane and their dispersions

The purpose of this research is to study the synthesis and characterization of stable aqueous dispersions of externally chain extended polyurethane/urea compositions terminated by hydrolyzable or hydrolyzed trialkoxysilane groups incorporated through secondary amino groups. These dispersions with excellent storage stability are substantially free from organic solvents which cure to water and solvent resistant, tough, scratch resistant, preferably light stable (non‐yellowing) silylated polyurethane (SPU) films. The films were characterized by FT‐IR, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), tensile strength and water contact angle measurements, nanoindentation, gel content, water and xylene swellability tests. The properties of the films were discussed and correlated in detail by changing length of soft segment, diisocyanates, NCO/OH ratio and chain extender, ethylenediamine (EDA). From the results, it was found that the particle size and viscosity are lower whereas the gel content and thermal stability are higher for SPUs. Modulus, hardness and tensile properties of SPU films are superior compared to EDA‐PU film. Higher water contact angle and residual weight percentage of SPU films confirm silylation of PU by [3‐(phenylamino)propyl]trimethoxysilane (PAPTMS). Increase in NCO/OH ratios consumes more quantity of PAPTMS which makes PU with superior mechanical properties. Higher PAPTMS content in SPU results in effective crosslinking of the functional silanol groups formed by hydrolysis reaction of trimethoxysilane groups. Overall, SPUs synthesized at 1.4 NCO/OH ratio using Poly‐(oxytetramethylene)glycol (PTMG)‐2000 and isophorone diisocyanate (or) toluene‐2,4‐diisocyanate have excellent properties compared to SPUs prepared using PTMG‐1000 and at 1.2 and 1.6 NCO/OH ratios. SPUs prepared at 1.6 NCO/OH ratio are brittle due to higher crosslinking density. In addition, the crosslinking density of the films can be modified through silane end‐group modification to produce SPUs with a wide range of physical properties. Copyright © 2007 John Wiley & Sons, Ltd.     

Polymeric Nanocomposites of Polyurethane Block Copolymers and Functionalized Multi‐Walled Carbon Nanotubes as Crosslinkers

Summary: We report on a new route to synthesize polymeric carbon nanotube‐polyurethane (PU) nanocomposites. Multi‐walled carbon nanotubes (MWNTs) functionalized by chemical modification were incorporated as a crosslinker in prepolymer, which was prepared from a reaction of 4,4′‐methylene bis(phenylisocyanate) and poly(ε‐caprolactone)diol. The reinforcing effect of carbon nanotubes in crosslinked MWNT‐PU nanocomposites was more pronounced as compared to that in conventional MWNT‐PU nanocomposites. The optimum content of chemically modified MWNTs for crosslinking with polyurethane was determined to be approximately 4 wt.‐% in our samples, based on observation of a NCO peak in FT‐IR spectroscopy. MWNT‐crosslinked polyurethane containing 4 wt.‐% modified MWNTs showed the highest modulus and tensile strength among the composites and pure PU. The presence of functionalized MWNTs in the polymeric nanocomposite yielded enhancement in the thermal stability due to crosslinking of the MWNTs with PU.

Possible configuration for MWNT‐PU nanocomposite molecules and FT‐IR spectra of samples obtained during reaction of prepolymer with functionalized MWNTs (second step).     

Mechanical properties of solvolysis lignin-derived polyurethanes

In order to study the tensile properties of solvolysis lignin polyurethanes, polyurethane (PU) films were prepared from the solvolysis lignin (SL)–polyethylene glycol (PEG)–diphenylmethane diisocyanate (MDI) system, and in addition to this further PU films were also prepared from the SL–MDI system. In the SL–PEG-MDI system, the SL content, the molecular weight of PEG and the NCO:OH ratio were varied in order to control the physical properties. The tensile stress and Young's modulus of the PUs of the SL–PEG–MDI type increased with increasing SL content and NCO:OH ratio. The tensile properties of the PUs from the SL–MDI system showed no NCO:OH ratio dependency; i.e. the mechanical properties of PUs are not influenced by the change in crosslinking. It is possible to control the tensile properties of PUs of the SL–PEG–MDI type by changing the content of PEG and SL at a constant NCO:OH ratio.     

环氧改性水性聚氨酯乳液的制备及其膜性能

以聚己内酯二元醇(CAPA)为软段,异佛尔酮二异氰酸酯(IPDI)和六亚甲基二异氰酸酯(HDI)为硬段,环氧树脂E-44为大分子交联剂,经相转化法合成了一系列环氧树脂改性负离子水性聚氨酯(EPPU)自乳化乳液,并制备了改性水性聚氨酯的固化膜.通过FTIR、TGA及接触角、力学性能测试对聚合物结构及其膜性能进行了研究.通过原子力显微镜(AFM)观察膜表面形态和表面粗糙度.乳液粒径及粒径分布通过动态激光光散射法(DLLS)测定.FTIR分析表明环氧树脂的羟基和环氧基都参与了发应.TGA表明,环氧树脂的加入可以提高聚氨酯的热稳定性.随着w(E-44)增大,改性聚氨酯膜的拉伸强度得到改善,断裂伸长率减小.随着w(E-44)增大,乳液粒径增大,薄膜的接触角增大,改性后的PU膜表面光滑度下降,拒水性增强.     

Effect of Molecular Weight of WPU on the Heterogenic PUA Composite Latex Prepared by Soap-Free Emulsion Polymerization

Aqueous acrylic-polyurethane (PUA) composite emulsion was prepared by soap-free seeded emulsion copolymerization. Waterborne polyurethane (WPU) was used as the seeded emulsion and functioned as surfactant. The effect of molecular weight of WPU on the heterogenic was investigated. The molecular weight of WPU was controlled by varying the NCO/OH mole ratio. The GPC results confirmed that the molecular weight of WPU presented double distribution. And the molecular weight of WPU decreased with the increasing NCO/OH mole ratio. Surface tension test indicated that the molecular weight had little influence on the surface activity of WPU. However, after emulsion copolymerization of acrylic monomers, the morphology and properties of the PUA composite were impacted markedly by the molecular weight of WPU. With an increase in the NCO/OH mole ratio, the morphology of PUA composite latex changed from core-shell structures to fish bowl structure, and the mechanical properties of PUA films changed correspondingly.     

High Solid Acrylic–Melamine Latexes with Tunable Crosslinking Capability

Miniemulsion polymerization is employed to produce high solid content (50%) acrylic/melamine latexes with varied crosslinking capability, for their potential application as waterborne crosslinkable coatings. This synthesis strategy allows the efficient incorporation of a hydrophobic crosslinker, iso‐butylated melamine (iBMF), into polymer particles, and to obtain latexes with different iBMF concentrations and acrylic polymer with varied content of hydroxylic groups (OH–). The involved crosslinking mechanisms and the physical transformations during film thermosetting of acrylic/iBMF nanocomposite are exhaustively investigated by combining thermal, spectroscopic, and thermo‐mechanical analyses. The influence of reactive groups concentration (iBMF and OH– content in the acrylic polymer) on the rate of curing, the crosslinking degree, and consequently onto the sensitive properties of cured films are discussed here.     

Influence of varying hard segments on the properties of chemically crosslinked moisture‐cured polyurethane‐urea

Polyurethane prepolymers are widely used in the reactive hot melt adhesives and moisture‐cured coatings. The chemically crosslinked moisture‐cured formulation based on PEG‐1000 and isophorone diisocyanate was prepared with NCO/OH ratio of 1.6:1.0. Trimethylol propane was used as a crosslinking agent. The excess isocyanate of the prepolymer was chain extended in the ratio of 2:1 (NCO/OH) with different aliphatic diols, and 4:1 with different aromatic diamines. The polymer network maturation during moisture cure was followed by dynamic mechanical thermal analyzer (DMTA) instrument. The thermal and dynamic mechanical properties of the crosslinked polymers were evaluated using thermogravimetric analysis, differential scanning calorimetric analysis and DMTA. Surface properties were evaluated through angle‐resolved X‐ray photoelectron spectroscopy. The present article discusses the physical properties of moisture‐cured polyurethane‐urea (MCPU) containing chemical crosslinks in the hard segment. The complete moisture‐cured polymers showed amorous results toward room temperature modulus, tensile strength, hardness, thermal stability, and transparency. The surface properties showed the enrichment of soft segments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 102–118, 2006     

高醚化三聚氰胺甲醛树脂交联水性聚氨酯的制备与表征

合成了高醚化三聚氰胺甲醛树脂(HMMM)交联改性含聚乙二醇单甲醚(Ymer N120)亲水基团的阴离子型水性聚氨酯。 通过全反射红外(ATR-FTIR)、差示扫描量热仪(DSC)、电子拉力机等技术手段表征了改性后的水性聚氨酯胶膜结构、热性能和力学性能。 结果表明,随着HMMM质量分数的增加,聚氨酯胶膜中氢键相互作用减弱,胶膜耐热性、耐水性、拉伸强度、粘接性均有所提高;当HMMM为8%时,聚氨酯胶膜的拉伸强度增加了125%,T-型剥离强度增加了7.4 N/cm,硬段最大热分解速率对应温度增加了38 ℃。 此外,交联水性聚氨酯胶膜的耐水性也得到了很大程度的提高。