Silver Nanoparticles Filling in TiO2 Hollow Nanofibers by Coaxial Electrospinning

This study investigated the coaxial electrospinning process of silver filling in TiO₂ ultrafine hollow fibers using polyvinyl pyrrolidone (PVP) sol/titanium n-butyloxide (Ti(OC₄H₉)₄) and PVP sol/silver nanoparticles as pore-directing agents. The bicomponent fibers were heat treated at 200 °C and calcined at 600 °C. Silver particles having diameters of 5 to 40 nm were deposited on the inner surface of the long hollow TiO₂ nanofibers (outer diameter of 150.300 nm) with mesoporous walls (thickness of 10.20 nm). The morphological structure of the filled ultrafine hollow fibers has been studied by means of infrared (IR) spectrum, X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The diameters and wall thicknesses of the hollow fibers could be tuned by adjusting the electrospinning parameters. Compared with other nanostructured TiO₂ materials, such as mesoporous Ag-TiO₂ blending fibers, TiO₂ hollow nanofibers, TiO₂ nanofibers, and TiO₂ powders, the silver filled TiO₂ hollow fibers exhibited a higher photocatalytic activity toward the degradation of methylene blue.     

Thermal study on electrospun polyvinylpyrrolidone/ammonium metatungstate nanofibers: optimising the annealing conditions for obtaining WO<Subscript>3</Subscript> nanofibers

This article demonstrates how important it is to find the optimal heating conditions when electrospun organic/inorganic composite fibers are annealed to get ceramic nanofibers in appropriate quality (crystal structure, composition, and morphology) and to avoid their disintegration. Polyvinylpyrrolidone [PVP, (C₆H₉NO) _n ] and ammonium metatungstate [AMT, (NH₄)₆[H₂W₁₂O₄₀]·nH₂O] nanofibers were prepared by electrospinning aqueous solutions of PVP and AMT. The as-spun fibers and their annealing were characterized by TG/DTA-MS, XRD, SEM, Raman, and FTIR measurements. The 400–600 nm thick and tens of micrometer long PVP/AMT fibers decomposed thermally in air in four steps, and pure monoclinic WO₃ nanofibers formed between 500 and 600 °C. When a too high heating rate and heating temperature (10 °C min⁻¹, 600 °C) were used, the WO₃ nanofibers completely disintegrated. At lower heating rate but too high temperature (1 °C min⁻¹, 600 °C), the fibers broke into rods. If the heating rate was adequate, but the annealing temperature was too low (1 °C min⁻¹, 500 °C), the nanofiber morphology was excellent, but the sample was less crystalline. When the optimal heating rate and temperature (1 °C min⁻¹, 550 °C) were applied, WO₃ nanofibers with excellent morphology (250 nm thick and tens of micrometer long nanofibers, which consisted of 20–80 nm particles) and crystallinity (monoclinic WO₃) were obtained. The FTIR and Raman measurements confirmed that with these heating parameters the organic matter was effectively removed from the nanofibers and monoclinic WO₃ was present in a highly crystalline and ordered form.     

Synthesis of electrospun BaSrTiO<Subscript>3</Subscript>/PVP nanofibers

Ba_1−x Sr _x TiO₃(x = 0–0.5, BST) nanofibers with diameters of 150–210 nm were prepared by using electrospun BST/polyvinylpyrrolidone (PVP) composite fibers by calcination for 2 h at temperatures in the range of 650–800 °C in air. The morphology and crystal structure of calcined BST/PVP nanofibers were characterized as functions of calcination temperature and Sr content with an aid of XRD, FT-IR, and TEM. Although several unknown XRD peaks were detected when the fibers were calcined at temperatures less than 750 °C, they disappeared with increasing the temperature (above 750 °C) due to its thermal decomposition and complete reaction in the formation of BST. In addition, the FT-IR studies of BST/PVP fibers revealed that the intensities of the O–H stretching vibration bands (at 3430 and 1425 cm⁻¹) became weaker with increasing the calcination temperature and a broad band at 540 cm⁻¹, Ti–O vibration, appeared sharper and narrower after calcination above 750 °C due to the formation of metal oxide bonds. However, no effect of Sr content on the crystal structure of the composites was detected.     

Synthesis,Characterization, and Photocatalytic Properties of Ag/TiO2 Composite Nanofibers Prepared by Electrospinning

Ag nanoparticles (Ag NPs) embedded titanium dioxide (TiO₂) nanofibers were fabricated by colloidal sol process, electrospinning, and calcination technique. Calcination of the electrospun nanofibers were heat treated at 600°C for 180 minutes in air atmosphere. X-ray diffraction patterns exhibited that the anatase phase and silver coexisted in the resulted Ag NPs/TiO₂ nanofibers; transmission electron microscopy demonstrated Ag NPs well spread in the porous microstructure of composite fibers. The prepared nanofibers were utilized as photocatalyst for degradation of methyl orange. The degradation rate of methyl orange dye solution containing Ag/TiO₂ composite nanofibers is 99% only after irradiation for 3 hours. It is proposed that these new Ag NPs/TiO₂ composite nanofibers will have potential application in water pollution treatment.      

Enhancement in the photocatalytic activity of TiO2 nanofibers hybridized with g-C3N4 via electrospinning

TiO₂/g-C₃N₄ nanofibers with diameter of 100–200 nm were prepared by electrospinning method after calcination at high temperature, using polyvinylpyrrolidone (PVP), Melamine (C₃H₆N₆), Ti(OC₄H₉)₄ as raw materials. The composite nanofibers were characterized by XRD, FT-IR, SEM, UV–vis and PL respectively. The effects of different g-C₃N₄ contents on structure and photocatalytic degradation of the composite nanofibers were investigated. The results indicated that with increasing g-C₃N₄ content, the diameter of the composite fibers increased and the morphology changed from uniform structure to a nonuniform one, containing beads. The composite nanofibers displayed the best photocatalytic degradation on RhB, when the g-C₃N₄ content was 0.8 wt%. The degree of degradation was up to 99% at the optimal conditions of 40 min. The degradation activity of the composite nanofibers on RhB, MB and MO was found to be higher than that of the TiO₂ nanofibers.     

Preparation of TiO<Subscript>2</Subscript> nanofibers immobilized on quartz substrate by electrospinning for photocatalytic degradation of ranitidine

The photocatalytic activity of TiO₂ nanofibers immobilized on quartz substrates was investigated by evaluating the decomposition of organic pollutants. TiO₂ nanofibers were synthesized by electrospinning the Ti-precursor/polymer mixture solution, followed by hot-pressing for enhancing the adhesion of TiO₂-nanofiber films to the substrates. TiO₂ started to crystalize in the anatase form at 500 °C and reached the optimal photocatalytic anatase/rutile phase ratio of 70:30 at a calcination temperature of 600 °C. The TiO₂-nanofiber film was demonstrated to be an efficient photocatalyst by ranitidine decomposition under UV illumination and was proven to have a comparable photocatalytic activity with the well-known Degussa P25 nanoparticulate photocatalyst and excellent recyclability during 10 cycles of photocatalytic operation, indicating no loss of TiO₂ nanofibers during photocatalytic operations.     

Alumina nanofibers obtained via electrospinning of pseudo-boehmite sol/PVP solution

Alumina nanofibers were fabricated by calcination of the polyvinylpyrrolidone (PVP)/pseudo-boehmite nanocomposite precursor fibers formed by electrospinning PVP/ethanol solution of dispersed pseudo-boehmite nanoparticles with and without additive of silica. The evolution of the phase, mechanical property and morphological features of the calcined fibers were studied and the effect of adding SiO₂ on the phase transformation of alumina was discussed. Adding SiO₂ can retard the phase transformation of γ-Al₂O₃ to α-Al₂O₃ and therefore inhibit the growth of alumina grains during calcination. Upon calcining the precursor fibers with 4 wt% SiO₂ additive at 1,300 °C, continuous alumina nanofibers with diameter ranging from 300 to 800 nm were obtained. These continuous nanofibers exhibited good flexibility and could be very promising for applications in filtration and catalyst support.     

Fabrication and magnetic properties of electrospun copper ferrite (CuFe2O4) nanofibers

Tetragonal copper ferrite (CuFe₂O₄) nanofibers were fabricated by electrospinning method using a solution that contained poly(vinyl pyrrolidone) (PVP) and Cu and Fe nitrates as alternative metal sources. The as-spun and calcined CuFe₂O₄/PVP composite samples were characterized by TG-DTA, X-ray diffraction, FT-IR, and SEM, respectively. After calcination of the as-spun CuFe₂O₄/PVP composite nanofibers (fiber size of 89 ± 12 nm in diameter) at 500 °C in air for 2 h, CuFe₂O₄ nanofibers of 66 ± 13 nm in diameter having well-developed tetragonal structure were successfully obtained. The crystal structure and morphology of the nanofibers were influenced by the calcination temperature. After calcination at 600 and 700 °C, the nature of nanofibers changed which was possibly due to the reorganization of the CuFe₂O₄ structure at high temperature, and a fiber structure of packed particles or crystallites was prominent. Crystallite size of the nanoparticles contained in nanofibers increases from 7.9 to 23.98 nm with increasing calcination temperature between 500 and 700 °C. Room temperature magnetization results showed a ferromagnetic behavior of the calcined CuFe₂O₄ samples, having their specific saturation magnetization (M_s) values of 17.73, 20.52, and 23.98 emu/g for the samples calcined at 500, 600, and 700 °C, respectively.     

Fabrication of TiN nanorods by electrospinning and their electrochemical properties

TiN nanorods were synthesized using electrospinning technique followed by thermolysis in different atmospheres. A dimethyl formamide-ethanol solution of poly-(vinyl pyrrolidone) and Ti (IV)-isopropoxide was used as the electrospinning precursor solution and as-spun nanofibers were calcined at 500 °C in air to generate TiO₂ nanofibers. Subsequently, a conversion from TiO₂ nanofibers to TiN nanorods was employed by the nitridation treatment at 600∼1400 °C in ammonia atmosphere. A typical characteristic of the final products was that the pristine nanofibers were cut into nanorods. The conversion from TiO₂ to TiN was realized when the nitridation temperature was above 800 °C. As-prepared nanorods were composed of TiN nano-crystallites and the average crystallite size gradually increased with the increase of the nitridation temperature. Electrochemical properties of TiN nanorods showed strong dependence on the nitridation temperature. The maximum value of the specific capacitance was obtained from the TiN nanorods prepared at 800 °C.     

Structural evolution and magnetic properties of SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript> nanofibers by electrospinning

The SrFe₁₂O₁₉/poly (vinyl pyrrolidone) (PVP) composite fiber precursors were prepared by the sol-gel assisted electrospinning with ferric nitrate, strontium nitrate and PVP as starting reagents. Subsequently, the M-type strontium ferrite (SrFe₁₂O₁₉) nanofibers were derived from calcination of these precursors at 750–1,000 °C.The composite precursors and strontium ferrite nanofibers were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy and vibrating sample magnetometer. The structural evolution process of strontium ferrite consists of the thermal decomposition and M-type strontium ferrite formation. After calcined at 750 °C for 2 h the single M-type strontium ferrite phase is formed by reactions of iron oxide and strontium oxide produced during the precursor decomposition process. The nanofiber morphology, diameter, crystallite size and grain morphology are mainly influenced by the calcination temperature and holding time. The SrFe₁₂O₁₉ nanofibers characterized with diameters of around 100 nm and a necklace-like structure obtained at 900 °C for 2 h, which is fabricated by nanosized particles about 60 nm with the plate-like morphology elongated in the preferred direction perpendicular to the c-axis, show the optimized magnetic property with saturation magnetization 59 A m² kg⁻¹ and coercivity 521 kA m⁻¹. It is found that the single domain critical size for these M-type strontium ferrite nanofibers is around 60 nm.     

Photocatalytic Crystalline and Amorphous TiO2 Nanotubes Prepared by Electrospinning and Atomic Layer Deposition

In this work core/shell composite polymer/TiO₂ nanofibers and from those TiO₂ nanotubes were prepared. First, poly(vinyl alcohol) (PVA) and poly(vinylpyrrolidone) (PVP) fibers were synthetized by electrospinning. They were covered with a 100 nm thick amorphous TiO₂ layer by atomic layer deposition at 50 °C. Later the polymer core was removed by two different methods: dissolution and annealing. In the case of dissolution in water, the as-prepared TiO₂ nanotubes remained amorphous, while when annealing was used to remove the polymers, the TiO₂ crystallized in anatase form. Due to this, the properties of amorphous and crystalline TiO₂ nanotubes with exactly the same structure and morphology could be compared. The samples were investigated by SEM-EDX, ATR-IR, UV-Vis, XRD and TG/DTA-MS. Finally, the photocatalytic properties of the TiO₂ nanotubes were studied by decomposing methyl-orange dye under UV light. According to the results, crystalline anatase TiO₂ nanotubes reached the photocatalytic performance of P25, while amorphous TiO₂ nanotubes had observable photocatalytic activity.     

Electrochemical Properties of Fiber‐in‐Tube‐ and Filled‐Structured TiO2 Nanofiber Anode Materials for Lithium‐Ion Batteries

Phase‐pure anatase TiO₂ nanofibers with a fiber‐in‐tube structure were prepared by the electrospinning process. The burning of titanium‐oxide‐carbon composite nanofibers with a filled structure formed as an intermediate product under an oxygen atmosphere produced carbon‐free TiO₂ nanofibers with a fiber‐in‐tube structure. The sizes of the nanofiber core and hollow nanotube were 140 and 500 nm, respectively. The heat treatment of the electrospun nanofibers at 450 and 500 °C under an air atmosphere produced grey and white filled‐structured TiO₂ nanofibers, respectively. The initial discharge capacities of the TiO₂ nanofibers with the fiber‐in‐tube and filled structures and the commercial TiO₂ nanopowders were 231, 134, and 223 mA h g^?1, respectively, and their corresponding charge capacities were 170, 100, and 169 mA h g^?1, respectively. The 1000th discharge capacities of the TiO₂ nanofibers with the fiber‐in‐tube and filled structures and the commercial TiO₂ nanopowders were 177, 64, and 101 mA h g^?1, respectively, and their capacity retentions measured from the second cycle were 89, 82, and 52 %, respectively. The TiO₂ nanofibers with the fiber‐in‐tube structure exhibited low charge transfer resistance and structural stability during cycling and better cycling and rate performances than the TiO₂ nanofibers with filled structures and the commercial TiO₂ nanopowders.     

Mg/Na-doped rutile TiO2 nanofiber mats for high-speed and anti-fogged humidity sensors

Mg²⁺ and Na⁺ doped rutile TiO₂ nanofibers have been prepared through in situ electrospinning technique and calcination with poly(vinyl pyrrolidone) (PVP) nanofibers as sacrificed template. The as-prepared composite nanofibers are spin-coated onto a ceramic substrate with three pairs of carbon interdigital electrodes to measure its humidity sensing behaviors. The product exhibits high-speed response (2 s) and recovery (1 s) for detecting moisture. Additionally, under UV irradiation, a water contact angle (θ) of nearly 0° has been observed based on the product, providing our humidity sensor with the anti-fogged properties.     

Thermodynamic study of direct reduction of high-chromium vanadium–titanium magnetite (HCVTM) based on phase equilibrium calculation model

High-chromium vanadium–titanium magnetite (HCVTM) is a good valuable resource with high iron content in the form of complex iron ore which contains various valuable metal elements such as iron, vanadium, titanium, chromium. Direct reduction of HCVTM is studied based on thermodynamic analysis. Combined TG experimental verification and equilibrium calculation model was used to analyze the reaction sequence and equilibrium amount in this paper. The contents in HCVTM reduction system are simplified as 18 kinds of chemical compositions. Reductions of Fe₃O₄ and FeO·TiO₂ are the main reduction reactions and are mainly reduced by C. The reduction reaction sequence of FeO·TiO₂ is FeO·TiO₂, TiO₂, TiC, and Ti; the reduction reaction sequence of Fe₃O₄ is Fe₃O₄, FeO, and Fe. The minimum reduction temperature of HCVTM is 860 °C. The reduction of Cr is difficult to implement, and the minimum reduction temperature of V is above 700 °C. The gas phase in this system is mainly CO when the temperature is above 1000 °C. CO partial pressure curve of gasification reaction is in the shape of ‘S’ with increase of temperature. When the temperature is 1350 °C, C/O is 1.0 and reduction time is 30 min, HCVTM can be reduced thoroughly and the reduction degree can reach to 0.98. When C/O is lower than 1.0, FeTi₂O₅ is the reduction intermediate products from FeO·TiO₂. When C/O is 1.0, diffraction peaks of Fe₃O₄ and FeO·TiO₂ disappear, and they are reduced to Fe and TiO₂.

     

Photocatalytic Activity of TiO2 Nanofibers with Doped La Prepared by Electrospinning Method

La‐TiO₂ nanofibers are prepared by a sol‐gel assisted electrospinning method. The structure and morphology of La‐TiO₂ nanofibers are characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM). XRD analysis shows that the weight percentage of anatase and rutile in the 1.5 mol% La‐TiO₂ nanofibers calcined at 600 °C is about 8:2, which is similar to P‐25. The XRD data of La‐TiO₂ nanofibers with different La content shows that La³⁺ dopant has a great inhibition on TiO₂ phase transformation. The photocatalytic activity of the as‐prepared La‐TiO₂ nanofibers is evaluated by photocatalytic decolorization of Methylene Blue (MB) aqueous solution. The results show that the 1.5 mol% La‐TiO₂ nanofibers calcined at 600 °C exhibit high photocatalytic activity, indicating that 600 °C and 1.5 mol% are the appropriate calcination temperature and optimal molar ratio of La to Ti, respectively.     

Synthesis and characterization of TiO2 powders by the double-nozzle electrospray pyrolysis method. Part 2. Material evaluation

Here we report the synthesis and characterization of anatase TiO₂ powders by the double-nozzle electrospray pyrolysis method. Titanium(IV) bis(ammonium lactato) dihydroxide (TALH) aqueous solution (2.0 wt%) and pure H₂O were separately injected into capillaries by using two syringe pumps, and were electrosprayed by using positive (+4 kV) and negative (−4 kV) DC voltage, respectively. Under a stream of dry clean air, the droplets were carried to the stainless steel tube heated with a tubular furnace at 350–450 °C. Thanks to the neutralization of droplets by the double-nozzle electrospray, the final TiO₂ powder yield after pyrolysis was much improved from 6% (by single nozzle) to 55.4% (in this study), although the particle size distribution became wider due to the electrical neutralization and coalescence of the droplets. Photocatalytic activity for H₂ evolution was studied.     

Micro- and nano-scale hollow TiO2 fibers by coaxial electrospinning: Preparation and gas sensing

We report the preparation of micro- and nano-scale hollow TiO₂ fibers using a coaxial electrospinning technique and their gas sensing properties in terms of CO. The diameter of hollow TiO₂ fibers can be controlled from 200 nm to several micrometers by changing the viscosity of electrospinning solutions. Lower viscosities produce slim hollow nanofibers. In contrast, fat hollow microfibers are obtained in the case of higher viscosities. A simple mathematical expression is presented to predict the change in diameter of hollow TiO₂ fibers as a function of viscosity. The successful control over the diameter of hollow TiO₂ fibers is expected to bring extensive applications. To test a potential use of hollow TiO₂ fibers in chemical gas sensors, their sensing properties to CO are investigated at room temperature.     

Synthesis of polytitanosiloxanes and their transformation to SiO2–TiO2 ceramic fibers

A one-pot synthesis of polytitanosiloxanes (PTS) and its transformation to SiO₂–TiO₂ ceramic fibers were investigated. PTS was prepared by the hydrolysis of tetraethoxysilane followed by the reaction with bis(2,4-pentanedionato)titanium diisopropoxide in methanol in 33–95 SiO₂ mol %. PTS was considered to be a ladder- or sheet-type polymer consisting of Si? O? Si and Si? O? Ti linkages as a main chain with pendant hydroxyl and 2,4-pentanedionato groups. SiO–TiO ceramic fibers were prepared by the pyrolysis of SiO₂–TiO₂ precursor fibers, which were prepared by the dry spinning of PTS followed by steam treatment. The tensile strength was 610 MPa for the SiO₂–TiO₂ fibers (SiO₂/TiO₂ = 20) after the pyrolysis at 700₀C. © 1994 John Wiley & Sons, Inc.     

YF3:Eu3+纳米纤维/高分子复合纳米纤维的制备与表征

采用静电纺丝技术制备了Y2O3:Eu3+纳米纤维,使用NH4HF2为氟化剂,经双坩埚法氟化和脱氨后得到YF3:Eu3+纳米纤维,再采用静电纺丝技术制备了YF3:Eu3+纳米纤维/PVP复合纳米纤维. XRD分析表明,立方相的Y2O3:Eu3+氟化后,得到了正交相的YF3:Eu3+纳米纤维,空间群为Pnma;YF3:Eu3+纳米纤维/PVP复合纳米纤维具有明显的YF3:Eu3+的衍射峰. SEM分析表明,YF3:Eu3+纳米纤维与YF3:Eu3+纳米纤维/PVP复合纳米纤维的直径分别为91±11 nm、319±43 nm,表面光滑. 用Shapiro-Wilk方法检验,纤维直径属于正态分布. 荧光光谱分析表明,YF3:Eu3+纳米纤维和YF3:Eu3+纳米纤维/PVP复合纳米纤维的最强发射峰均位于588 nm和595 nm,属于Eu3+的5D0→7F1跃迁,表明Eu3+占据YF3基质中Y3+晶格点的C2对称格位. PVP对YF3:Eu3+发光峰位没有影响,但发光强度降低;YF3:Eu3+的含量与YF3:Eu3+纳米纤维/PVP复合纳米纤维的发光强度成线性关系.     

Synthesis and optical property of NaTaO<Subscript>3</Subscript> nanofibers prepared by electrospinning

This paper describes a procedure of preparing sodium tantalite nanofibers for the first time. Sodium tantalite nanofibers were synthesised by electrospinning a sol–gel precursor solution of poly(vinyl pyrrolidone)/sodium tantalite, followed by careful sintering of the as-electrospun composite fibers at 550 °C for 3 h. The morphology, microstructure and crystal phase were investigated by transmission electron microcopy and X-ray diffraction. The optical property was characterized by ultraviolet–visible (UV–vis) spectrometer. Typical nanofibers were with diameter between 70 and 90 nm and length exceeding 0.1 mm. An unusual phenomenon, the red-shift of optical absorption band edge happened, indicated the fabricated NaTaO₃ nanofibers were potential good candidates for photocatalytic application. The experiment photodegradation of methylene blue by NaTaO₃ nanofibers under UV light irradiation was performed.