用石墨炉原子吸收法测定水质中微量砷,硒的探讨

采用石墨炉原子吸收法测定水中微量砷，硒，经大量实验条件摸索，选择不同仪器分析工作条件，找出了最佳升温程序条件，特别是原子化时气流控制，使分析方法的检出限降低为：Ａｓ０．６μｇ／Ｌ，Ｓｅ０．５μｇ／Ｌ。线性范围；Ａｓ０．０００－０．１２０ｍｇ／Ｌ，Ｓｅ０．０００－０．０２４ｍｇ／Ｌ；精密度，相对标准偏差分别为：Ａｓ１．２６％，３．６７％，Ｓｅ２．５６％，４．５７％，回收率为：Ａｓ９８．０％－１１０．     

新阻化动力学光度法测定痕量铜

１引言我们在实验中发现，铜（Ⅱ）抑制Ｍｎ（Ⅱ）催化铬（Ⅵ）与二安替比林基对氯苯基甲烷（ＤＡＰＣＭ）的显色反应，从而建立了一种新的测定铜（Ⅱ）的阻化动力学方法。该法灵敏度高，选择性较好，线性范围较宽，稳定时间长，操作简便。用于粗铅和铝合金中铜的测定，结果满意。２实验部分２．１主要仪器和试剂７２２型光栅分光光度计（山东高密分析仪器厂）；５０１型超级恒温器（江苏实验仪器厂）。铬（Ⅵ）标准溶液：１．０ｇ／Ｌ和１．０ｇ／Ｌ；铜（Ⅱ）标准溶液：１．１０ｇ／Ｌ和１．０ｍｇ／Ｌ；０．２％（Ｗ／Ｖ）ＤＡＰＣＭ溶液…     

2-乙基己醇萃取-原子吸收光谱法测定微量镓

在７．０ｍｏｌ／Ｌ盐酸介质中,在抗坏血酸存在下,用２－乙基己醇萃取试样溶液中的酸性铬蓝Ｋ－镓的络合物,然后用３０ｇ／Ｌ的硫脲将络合物反萃取到水相中,用ＦＡＡＳ法测定镓,据此建立了萃取反萃取－ＦＡＡＳ法测定微量镓的新方法。方法线性范围为０～６０．０ｍｇ／Ｌ,灵敏度为０．２８ｍｇ／Ｌ／１％,已用于铝酸钠溶液中微量镓的测定。     

毛细管区带电泳法测定甲氧苄胺嘧啶和磺胺甲基异噁唑的离解常数及其在复方新诺明中的含量

报道了利用 ３０ ｍｍｌ／Ｌ ＨＡｃ－ＮａＡｃ为缓冲液测定复方新诺明中甲氧苄胺嘧啶（ＴＭＰ）和磺胺甲基异噁唑（ＳＭＺ）的离解常数及含量的毛细管区带电泳（ＣＺＥ）方法。该方法具有简便、快速、准确等特点。测得ＴＭＰ和ＳＭＺ的ｐＫａ分别为６．６０和５．９０。其平均回收率分别为１０１．５％和９９．６％,最低检出限为０．４８ ｍｇ／Ｌ和０．０２８ ｍｇ／Ｌ,ＲＳＤ为１．２６％和１．１２％。     

抑制动力学分析法测定痕量铈

１引言研究了铈（Ⅲ）阻抑Ｈ２Ｏ２氧化水杨基荧光酮（ＳＡＦ）褪色的反应。反应对铈（Ⅲ）为一级反应，表观活化能为２８．７５ｋＪ／ｍｏｌ。据此建立了测定痕量铈的动力学分析法。测定条件为：ＳＡＦ：４．０ｘ１０－５ｍｏｌ／Ｌ，Ｈ２Ｏ２：０．０１０％，ＮａＯＨ：２．０ｘ１０－２ｍｏｌ／Ｌ，５０℃。线性范围０．０４～０．４４ｍｇ／Ｌ，检测限为０．０２ｍｇ／Ｌ。当溶液中的铈含量为０．１６ｍｇ／Ｌ时，３～８倍量的轻稀土，５～１１倍量的重稀土及同倍量铀和钍不干扰测定。２实验部分２．１试剂和仪器铈（Ⅲ）标准溶液：２０…     

催化动力学光度法测定痕量苯酚

研究了在硫酸介质中苯酚对Ｉ＾－１催化Ｃｅ＾４＋－Ａｓ（Ⅲ）反应的抑制作用及其动力学条件。建立了用催化动力这光度法测定痕量苯酚的新方法，结果表明，在０．００１ｍｏｌ／ＬＣｅ（ＳＯ４）２，０．００１２５ｍｏｌ／Ｌ，Ａｓ２Ｏ３，０．０１ｍｇ／Ｌ，ＫＩ，０．０１２５ｍｏｌ／Ｌ，Ｈ２ＳＯ４和０．１３％（ｗ／ｖ）ＮａＣｌ溶液中测定苯酚，其表面摩尔吸光系数为２．１×１０＾５Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，线性范围     

偏最小二乘催化极谱法同时测定铂,钯,铑

应用Ｍ２７３Ａ电化学系统中的线性扫描技术，确定了０．７５ｍｏｌ／ＬＨ２ＳＯ４－１．５％ＮＨ４Ｃｌ－２．８ｍｍｏｌ／Ｌ（ＣＨ２）６Ｎ４－０．００２５％Ｎ２Ｈ４．Ｈ２ＳＯ４为偏最小二乘极谱法同时测定Ｐｔ、Ｐｄ、Ｒｈ的最佳极谱体系。Ｐｔ、Ｐｄ、Ｒｈ的线性范围为３．２ｍｇ／Ｌ、０－１５．０ｍｇ／Ｌ和０－１．０ｍｇ／Ｌ。模拟样品及实际样品的回收率在９０．３－１０７．７％之间。     

痕量铼的同位素稀释中子活化分析

将同位素稀释法的准确性与中子活性分析（ＮＡＡ）的高灵敏度相结合，建立了一种新的痕量铼的测试方法，实验中对Ｒｅ的检出限为０．００４ｎｇ，全流程空白为０．０５ｎｇ，地于Ｒｅ含量为６４ｎｇ／ｇ的样品，在取样量为５０ｍｇ时，单次测定误差（２σ）为３．１％，测定Ｒｅ一为３０ｎｇ／ｇ的样品，本方法的２σ在３％以内，４次分析的ＲＳＤ为４．１％，而采用一般的ＮＡＡ，结果偏低约２０％，并且ＲＳＤ大于５％。     

螯合树脂静态富集／电热蒸发（ETV）—ICP—AES测定铂族元素Pt,Pd和Os

用含氮，硫功能团的螯合树脂ＹＰＡ，进行静态吸附，含待测定元素的浓缩物制成悬浮体，采用悬浮体进样／电热蒸发等离子体原子发射光谱（ＥＴＶ－ＩＣＰ－ＡＥＳ）直接测定。方法的检出限分别为０．５，０．７和４．０ｎｇ／ｍＬ（对Ｐｔ，Ｐｄ和Ｏｓ）相对标准偏差分别为２．６％，４．７％和３．８％（ｎ＝１０，Ｐｔ：２．０ｍｇ／Ｌ，Ｐｄ：２ｍｇ／Ｌ，Ｏｓ：５．０ｍｇ／Ｌ）。应用本法对质标样进行了分析，测定值与标准值基本     

HPLC法测定中成药制剂中10-羟基-2-癸烯酸的含量

采用ＳｐｈｅｒｉｓｏｒｂＣ１８柱,以甲醇∶水∶磷酸（４５∶６５∶０．５）为流动相,以ＵＶ２１０ｎｍ为检测波长,测定中成药制剂中１０－羟基－２－癸烯酸（１０－ＨＤＡ）的含量,１０－ＨＤＡ浓度在０．００６～０．０３０ｇ／Ｌ范围内线性关系良好（ｒ＝０．９９９９,ｎ＝５）,检测限为０．２ｍｇ／Ｌ（Ｓ／Ｎ＝３∶１）。方法具有定量准确、快速及主峰和杂质分离度高等特点。     

Colour reaction of free chlorine with p-amino-N,N-diethylaniline in the presence of alcohol and its analytical application

A simple, precise, rapid-colour-forming and stable spectrometric method has been developed for determining free chlorine in water. p-Amino-N,N-diethylaniline reacts with free chlorine almost instantaneously in the presence of alcohol to form a red oxidized product with absorption maximum at 513 nm. Beer's law is obeyed in the free chlorine concentration range of 0-2 microg ml(-1). The molar absorptivity is 1.79 x 10(4) l mol(-1) cm(-1), limit of detection 0.0036 microg ml(-1), relative standard deviation 1.51%, and amount of free chlorine 7 microg. The colour reaction rate and absorbance are independent of temperature in the range 3-45 degrees C and the stable absorptivity lasts for at least 1 h. The method is satisfactory for the determination of free chlorine in aqueous solution.     

o-Dianisidine: a new reagent for selective spectrophotometric, flow injection determination of chlorine.

A flow injection analysis (FIA) procedure for the determination of free chlorine in industrial formulations and water samples is proposed. The manifold is provided with a gas-diffusion unit which permits the removal of interfering species and also the preconcentration of chlorine. The determination of chlorine is performed on the basis of the oxidation by o-dianisidine as a chromogenic reagent to a coloured product which can be monitored at 445 nm. The method (for a preconcentration step of 60 s) is linear over the range 0.04-1.00 mg l(-1) of chlorine, the limit of detection is 0.04 mg l(-1), the reproducibility of the procedure (as RSD of the slope) is 3.7% for a series of four independent calibrations, the precision (as RSD of a series of 30 continuous FIA peaks of 0.56 mg l(-1) of chlorine) is 1.4% and the sample throughput is 40 h(-1). A detailed comparative study of the analytical characteristics of a single mono-channel reverse FIA assembly and the same system but provided with a Fluoropore membrane filter of 0.5 microm pore size was performed to check the advantages of the new approach in terms of sensitivity, selectivity and limit of detection.     

Determination of residual chlorine by derivatisation with 2,6-dimethylphenol and gas chromatographic separation

Residual chlorine in aqueous solution is converted to 4-chloro-2,6-dimethylphenol, which is extracted into hexane and determined by gas chromatography. Relative standard deviations (n = 5) are 0.36–1.1% for chlorine concentrations of 8.6–0.01 mg l^-1 and chlorine recoveries are 99.2–101%. In the presence of dichromate (30 mg l^-1), relative standard deviations (n = 5) are 1.19–2.71% for chlorine concentrations of 9.3–0.1 mg l^-1. Oxidants and coloured solutes do not interfere.     

Flow injection analysis for residual chlorine using Pb(II) ion-selective electrode detector

A simple flow injection analysis (FIA) system for residual chlorine in tap water has been developed by using a Pb(II) ion-selective electrode (ISE) detector. The method is based on a specific response of the Pb(II)-ISE to residual chlorine. The FIA system consists of a millivolt meter, a peristaltic pump, a Pb(II)-ISE detector and a recorder. A linear working curve between peak height and concentration of residual chlorine was obtained from 0.1 to 1 mg l(-1) for the developed FIA system. The relative standard deviation for repeated injections of a 0.2 mg l(-1) residual chlorine sample was 2%. The regression line and its correlation factor between the conventional o-tolidine colorimetric method and the present method were Y=0.75X+0.17 and 0.967, respectively, for this determination.     

The use of chlorophenol red for the selective determination of chlorine dioxide in drinking water

In recent years, the use of chlorine dioxide as an alternative disinfectant for drinking water has become increasingly attractive. As a result, an accurate method for the determination of mg l(-1) concentrations of chlorine dioxide is needed. Improvements to chlorophenol red (CPR) spectrophotometry result in a selective method for ClO(2) with few interferences. CPR selectively reacts with 0.1-1.9 mg l(-1) ClO(2) at pH 7, yielding a linear response (0.9994) with a limit of detection of 0.12 mg l(-1) ClO(2). Several species, ClO(2)(-), ClO(3)(-), NH(2)Cl, and free available chlorine (FAC), were studied as potential interferents using this method. There was found to be less than 2% interference due to 1.38 mg l(-1) ClO(2)(-), 9.87 mg l(-1) ClO(3)(-1), and 5.31 mg l(-1) NH(2)Cl. The interference from up to 1.19 mg l(-1) FAC was 3.7% and could be further reduced by the addition of oxalic acid, sodium cyclamate or thioacetamide.     

Differentiation of the halogen content of peat samples using ion chromatography after combustion (TX/TOX-IC)

The proposed method for the differential AOX analysis of water samples was tested for its applicability to differentiate the halogen content of peat samples. For determination of the total and the total organic-bound chlorine, bromine and iodine, peat samples were combusted, and the combustion gases trapped and analyzed by ion chromatography (TX/TOX-IC). The total and the organically bound chlorine, bromine and iodine, respectively, can be determined by two-fold analysis with deviations of around 10%. With respect to chlorine more than a double determination could be required. The limit of quantification is 20 mg kg(-1) for chlorine, 2 mg kg(-1) for bromine and 1 mg kg(-1) for iodine, if 25 mg of peat is combusted. The most crucial step of the analysis is the inorganic halogen removal, which is necessary if the organically bound fraction is determined. However, there are some uncertainties about the complete removal of the inorganic halides from the solid samples. Thus, the values of the organically bound fraction have to be discussed as maximal concentrations. Nevertheless, we suggest that the applied method can be useful as a tool for studying the fate of halogens in soils.     

Determination of fluorine and chlorine in geological materials by induction furnace pyrohydrolysis and standard-addition ion-selective electrode measurement

Fluorine and chlorine in geological materials are volatilized by pyrohydrolysis at about 1150 degrees in a stream of oxygen (1000 ml/min) plus steam in an induction furnace. The catalyst is a 7:2:1 mixture of silica gel, tungstic oxide and potassium dihydrogen phosphate. The sample/catalyst mixture is pyrohydrolysed in a re-usable alumina crucible (already containing four drops of 1 + 3 phosphoric acid) inserted in a silica-enclosed graphite crucible. The absorption solution is buffered at pH 6.5 and spiked with 1.6 mug of fluoride and 16 mug of chloride per g of solution, to ensure rapid and linear electrode response during subsequent standard-addition measurement. The simple plastic absorption vessel has 99.5% efficiency. The 3s limits of detection are 5-10 mug/g and 40-100 mug/g for fluorine and chlorine respectively. The procedure is unsuitable for determining chlorine in coal.     

Certification of the chlorine content of the isotopic reference materials IRMM-641 and IRMM-642

The Slovak Institute of Metrology and the Institute for Reference Materials and Measurements have collaborated in the certification of the two chlorine reference materials IRMM-641 and IRMM-642. Until now no isotopically enriched chlorine isotopic reference material certified for isotopic composition and content has been available commercially. The isotopic reference materials IRMM-641 and IRMM-642 described herein are certified for isotopic composition and for chlorine content. The chlorine content of the reference material IRMM-641 was certified by use of high-precision argentometric coulometric titration at the Slovak Institute of Metrology. The base material used for IRMM-641 is NIST Standard Reference Material 975. The chlorine content of the reference material IRMM-642 was measured by isotope dilution, using negative thermal ionization mass spectrometry at the Institute for Reference Materials and Measurements. Both standard reference materials were prepared by dissolving NaCl in water. The reference material IRMM-641 contains 0.025022 +/- 0.00011 mol kg(-1) chlorine of natural isotopic composition with an n(37Cl)/n(35Cl) ratio of 0.31977 +/- 0.00082. The reference material IRMM-642 contains 0.004458 +/- 0.000028 mol kg(-1) chlorine with an n(37Cl)/n(35Cl) ratio of 0.01914 +/- 0.00088.     

Reaction of 4-Ethoxy-2-(2,3,3-trichloro-1-nitro- 2-propenylidene)benzazetine with Methyl- and Phenyllithium

The reactions of 4-ethoxy-2-(2,3,3-trichloro-1-nitro-2-propenylidene)benzazetine with methyl- and phenyllithium at a ratio of 1:2 result in replacement of one chlorine atom and formation, respectively, of 4-ethoxy-2-(2,3-dichloro-3-methyl-1-nitro-2-propenylidene)benzazetine and 4-ethoxy-2-(2,3-dichloro-1-nitro-3-phenyl-2-propenylidene)benzazetine in 45 and 52% yield. With excess phenyllithium (reactant ratio 1:5), a mixture of products is formed due to replacement of one, two, and three chlorine atoms by phenyl groups. An analogous reaction with methyllithium is nonselective.     

高温水解–离子色谱法测定八氧化三铀中的氟和氯

建立了高温水解–离子色谱法测定八氧化三铀中氟和氯含量的方法。对影响高温水解的因素进行了试验研究,水解温度为1 050℃,水浴温度为(85±1)℃,氩气流量为600 mL/min,水解时间为1 h。选用Ion Pac AG11–HC(50 mm×4 mm)阴离子保护柱和Ion Pac AS11–HC(250 mm×4 mm)阴离子分析柱对样品进行分离,以氢氧化钾溶液等度淋洗。在0~5.00μg/mL范围内,氟和氯均有良好的线性,相关系数(r~2)分别为0.999 9,0.999 4;检出限分别为3,4μg/g。氟和氯测定结果的相对标准偏差分别为4.72%,3.23%(n=6),加标回收率分别为97%~101%,95%~99%。该法操作简便、快速,适用于八氧化三铀中氟和氯的检测。