Determination of dopamine in synthetic cerebrospinal fluid by SWV with a graphite–polyurethane composite electrode

This work describes an electroanalytical investigation of dopamine using cyclic voltammetry (CV) and the graphite–polyurethane composite electrode (GPU). In CV studies, well-defined redox peaks characterize the oxidation process at the GPU electrode, which is indicative of electrocatalytic effects associated with active sites on the GPU electrode surface. A new analytical methodology was developed using the GPU electrode and square wave voltammetry (SWV) in BR buffer solution (0.1 mol L^–1; pH 7.4). Analytical curves were constructed under optimized conditions (f=60s^–1, E_a=50 mV, E_I=2 mV) and detection and quantification limits of 6.4×10^–8 mol L^–1 (12.1 g L^–1) and 5.2×10^–6 mol L^–1 (0.9 mg L^–1), respectively, were achieved. The precision of the method was checked by performing ten successive measurements for a 9.9×10^–6 mol L^–1 dopamine solution. For intra-assay and inter-assay precisions, the relative standard deviations were 1.9 and 2.3%, respectively. In order to evaluate the developed methodology, the determination of dopamine was performed with good sensitivity and selectivity, without the interference of ascorbic acid in synthetic cerebrospinal fluid, which indicates that the new methodology enables reliable analysis of dopamine.     

Square-wave voltametric method for determination of molinate concentration in a biological process using a hanging mercury drop electrode

A square-wave voltammetric (SWV) method using a hanging mercury drop electrode (HMDE) has been developed for determination of the herbicide molinate in a biodegradation process. The method is based on controlled adsorptive accumulation of molinate for 10 s at a potential of –0.8 V versus AgCl/Ag. An anodic peak, due to oxidation of the adsorbed pesticide, was observed in the cyclic voltammogram at ca. –0.320 V versus AgCl/Ag; a very small cathodic peak was also detected. The SWV calibration plot was established to be linear in the range 5.0×10^–6 to 9.0×10^–6 mol L^–1; this corresponded to a detection limit of 3.5×10^–8 mol L^–1. This electroanalytical method was used to monitor the decrease of molinate concentration in river waters along a biodegradation process using a bacterial mixed culture. The results achieved with this voltammetric method were compared with those obtained by use of a chromatographic method (HPLC–UV) and no significant statistical differences were observed.     

A flow-injection ultrafiltration sampling chemiluminescence system for on-line determination of drug–protein interaction

A flow-injection ultrafiltration sampling chemiluminescence system for on-line determination of cimetidine–bovine serum albumin (BSA) interaction is proposed in this paper. Cimetidine can be oxidized by N-bromosuccinimide (NBS) and sensitized by fluorescein to produce high chemiluminescence emission in basic media. The concentration of cimetidine is linear with the CL intensity in the range 3×10^–7–1×10^–4 mol L^–1 with a detection limit of 1×10^–7 mol L^–1 (3). The drug and protein were mixed in different molar ratios in 0.067 mol L^–1 phosphate buffer, pH 7.4, and incubated at 37 °C in a water bath. The ultrafiltration probe was utilized to sample the mixed solution at a flow rate of 5 µL min^–1. The data obtained by the proposed ultrafiltration flow-injection chemiluminescence method was analyzed with Scrathard analysis and a Klotz plot. The estimated association constant (K) and the number of the binding site (n) on one molecule of BSA by Scrathard analysis and Klotz plot were 3.15×10⁴ L mol^–1 and 0.95, 3.25×10⁴ L mol^–1 and 0.92, respectively. The proposed system proved that flow-injection chemiluminescence analysis coupled with on-line ultrafiltration sampling is a simple and reliable technique for the study of drug–protein interaction.     

Transport properties and electroanalytical response characteristics of drotaverine ion-selective sensors

The construction and electroanalytical response characteristics of poly(vinyl chloride) matrix ion-selective sensors (ISSs) for drotaverine hydrochloride are described. The membranes incorporate ion-association complexes of drotaverine with tetraphenylborate, picrate, tetraiodomercurate, tetraiodobismuthate, Reinecke salt, and heteropolycompounds of Keggin structure—molybdophosphoric acid, tungstophosphoric acid, molybdosiliconic acid and tungstosiliconic acid as electroactive materials for ionometric sensor controls. These ISSs have a linear response to drotaverine hydrochloride over the range 8×10^–6 to 5×10^–2 mol L^–1 with cationic slopes from 51 to 58 mV per concentration decade. These ISSs have a fast response time (up to 1 min), a low determination limit (down to 4.3×10^–6 mol L^–1), good stability (3–5 weeks), and reasonable selectivity. Permeabilities and ion fluxes through a membrane were calculated for major and interfering ions. Dependences of the transport properties of the membranes on the concentrations of the ion exchanger and near-membrane solution and their electrochemical characteristics are presented. The ISSs were used for direct potentiometry and potentiometric titration (sodium tetraphenylborate) of drotaverine hydrochloride. Results with mean accuracy of 99.1±1.0% of nominal were obtained which corresponded well to data obtained by use of high-performance liquid chromatography.     

Spectrophotometric determination of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3- H-indol-2-ylidene)propenyl]-3 H-indolium

A new, simple, rapid, and sensitive spectrophotometric method has been developed for the determination of manganese in sewage. The method is based on the reaction of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3-H-indol-2-ylidene)propenyl]-3H-indolium to form a colored ion associate with a sensitive absorption maximum at 560 nm. The appropriate reaction conditions have been established: pH 8.5–10.0, 1.25–2.3×10^–3 mol L^–1 1-nitroso-2-naphthol, and 1.6–2.4×10^–4 mol L^–1 dye reagent. Beer's law is obeyed for manganese concentrations up to 4.2 mg L^–1. The limit of detection is 0.01 mg L^–1 Mn²⁺; the molar absorptivity of the ion associate was 7.5×10⁴ L mol^–1 cm^–1. The effect of various foreign ions was examined. A reaction mechanism is suggested. The developed procedure was tested for determination of manganese in sewage with satisfactory precision and accuracy.     

Simultaneous Determination of Aromatic Amines by Liquid Chromatography Coupled with Carbon Nanotubes/Poly (3-methylthiophene) Modified Dual-Electrode

Liquid chromatography with amperometric detection (LC-AD) is developed and applied to simultaneously determine five aromatic amines. In the LC-AD, a new carbon nanotubes/poly(3-methylthiophene) modified dual-electrode is fabricated and then used as the working electrode. It is found that this chemically modified electrode (CME) exhibits efficiently electrocatalytic oxidation for aromatic amines with relatively high sensitivity, stability and long-life. Thus, lower detection in LC-AD can be achieved, which are 4.0 × 10^–8 mol L^–1 for aniline, 1.6 ×10^–7 mol L^–1 for 4-nitroaniline, 1.0 × 10^–7 mol L^–1 for 4-chloroaniline, 1.5 × 10^–7 mol L^–1 for 1-naphthylamine, 1.7 × 10^–7 mol L^–1 for 2-bromoaniline. The recoveries of the five analytes are also determined, which range between 0.95 and 1.05 for drinking water, 0.86 and 1.10 for the LiWa River water.     

Manganese detection in marine sediments: anodic vs. cathodic stripping voltammetry

Three different electroanalytical techniques for the detection of manganese in marine sediments are evaluated. The anodic stripping voltammetry of manganese at an in situ bismuth-film-modified boron-doped diamond electrode and cathodic stripping voltammetry at a carbon paste electrode are shown to lack the required sensitivity and reproducibility whereas cathodic stripping voltammetry at a bare boron-doped diamond electrode is shown to be reliable and selective with a limit of detection, from applying a 60 s accumulation period of 7.4 × 10⁻⁷ M and a sensitivity of 0.24 A M⁻¹. The method was used to evaluate the manganese content of marine sediments taken from Šibenik, Croatia.     

Determination of thiol compounds in rat striatum microdialysate by HPLC with a nanosized CoHCF-modified electrode

A cobalt hexacyanoferrate (CoHCF) nanoparticle (size ca. 60 nm) chemically modified electrode (CME) was fabricated and the electrochemical behavior of thiols at this nanosized CoHCF CME was studied. In comparison with a bare glassy carbon (GC) electrode and with a general CoHCF CME which was electrodeposited in the traditional manner, the present nanosized CoHCF CME efficiently performed electrocatalytic oxidation for glutathione (GSH) and L-Cysteine (L-Cys) with relatively high sensitivity, outstanding stability, and long-life. Combined with high-performance liquid chromatography (HPLC), the nanosized CoHCF CME was used for electrochemical determination (ECD) of GSH and L-Cys. The peak currents were a linear function of concentrations in the range 2.0×10^–7 to 2.0×10^–4 mol L^–1 for both GSH and L-Cys, with detection limits of 1.2×10^–7 and 1.0×10^–7 mol L^–1, respectively. Coupled with microdialysis sampling, the HPLC–ECD system has been successfully used to assess the GSH and L-Cys content of rat striatum.     

Simultaneous determination of sodium dodecyl sulphate and sodium linear-dodecylbenzenesulphonate with 1-stearyl-4-(4-aminonaphthylazo)-pyridinium bromide by spectrophotometry

A rapid and sensitive spectrophotometric method for the simultaneous determination of sodium dodecyl sulphate (SDS) and sodium linear-dodecylbenzenesulphonate (DBS) with 1-stearyl-4-(4-aminonaphthylazo)-pyridinium bromide (SAPB) is described using the difference at the maximum absorption wavelength of the SDS- and the DBS-ion associate. SDS and DBS have been determined independently by measuring their respective absorbances at the maximum absorption wavelength. The apparent molar absorptivities of the SDS- and the DBS-ion associate are 8.0×10⁴ l mol^–1 cm^–1 at 445 nm and 4.5×10⁴ l mol^–1 cm^–1 at 424 nm, respectively. The calibration graph for SDS is linear in the range from 0.1 to 1.0×10^–6 mol/l in the presence of 1.2×10^–6 mol/l DBS and for DBS from 0.8 to 2.0×10^–6 mol/l in the presence of 8.0×10^–7 mol/l SDS. The relative standard deviation (n=15) for 8.0×10^–7 mol/l SDS is 3.4% and for 1.6×10^–6 mol/l DBS 2.1%. The proposed method has been applied to the simulatenous determination of SDS and DBS in river water samples.     

Voltammetric study of glibenclamide at carbon paste and Sephadex-modified carbon paste electrodes

The oxidative behaviour of the antidiabetic agent glibenclamide on a bare carbon paste electrode (CPE) and a Sephadex-modified carbon paste electrode (SMCPE) was explored by cyclic and differential pulse voltammetry (DPV). The analysis procedure consisted of an open circuit accumulation step in stirred sample solution of Britton-Robinson buffer (0.04 mol L^–1, pH 2.0). This was followed by medium exchange to a clean solution of Britton-Robinson buffer (0.04 mol L^–1, pH 5.0), and subsequently an anodic potential scan was effected to obtain the voltammetric peak. The glibenclamide oxidation peak current obtained by DPV was proportional to the concentration of the glibenclamide in the range of 1.0×10^–9 mol L^–1 to 5.0×10^–8 mol L^–1 for 180 s accumulation time, with a detection limit of 4.0×10^–10 mol L^–1. A method was developed for the determination of glibenclamide in formulation and spiked human serum. Moreover, the proposed procedure was used to estimate the serum concentrations after oral administration of a 5 mg tablet of glibenclamide to three diabetic subjects.     

Sonoelectroanalysis: investigation of bismuth-film-modified glassy carbon electrodes

Bismuth-modified glassy carbon electrodes have been investigated for their suitability in sonoelectroanalysis. The stability of the bismuth film to the application of ultrasound was assessed via voltammetric and atomic force microscopy (AFM) studies which revealed little ablation at powers up to an intensity of 130 W cm^–2 delivered from a 25-kHz sonic horn. Furthermore, bismuth-film-modified glassy carbon electrodes were evaluated for the sonoelectroanalytical quantification of zinc and cadmium. Detection limits of 2×10^–7 M and 6×10^–9 M respectively were found after a 60-s deposition time via an acoustically assisted deposition protocol.     

Determination of subnanomolar concentrations of cobalt by adsorptive stripping voltammetry at a bismuth film electrode

Procedures for trace cobalt determinations by adsorptive stripping voltammetry at in situ and ex situ plated bismuth film electrodes are presented. These exploit the enhancement of the cobalt peak obtained by using the Co(II)–dimethylglyoxime–cetyltrimethylammonium bromide–piperazine-N,N-bis(2-ethanesulfonic acid) system. The calibration graph for an accumulation time of 120 s was linear from 2 × 10^–10 to 2 × 10^–8 mol L^–1. The relative standard deviation from five determinations of cobalt at a concentration of 5 × 10^–9 mol L^–1 was 5.2%. The detection limit for an accumulation time of 300 s was 1.8 × 10^–11 mol L^–1. The proposed procedure was applied to cobalt determination in certified reference materials and in tap and river water samples.     

Electroanalytical study of a benzodiazepinooxazole: Mexazolam

Summary The electroanalytical behaviour of 10-chloro-11b-(2-chlorophenyl)-2,3,7,11b-tetrahydrooxazolo[3,2-d][1,4]-benzodiazepin-6(5H)-one (Mexazolam) was studied in the pH-range 1–13. The compound suffers a hydrolysis process, which can be followed by voltammetric techniques. The reduction process of Mexazolam is irreversible in the whole pH range 1–13 studied; the cathodic reactions of its hydrolysis products are irreversible at pH values lower than 7 and reversible in neutral and alkaline media at a scan rate range of 0.1–40 V·s^–1. The electrode process attributed to the reduction of the carbonyl group is predominantly adsorption-controlled and the reduction of the iminium group of the different species of Mexazolam is diffusion-controlled. A differential pulse polarographic method has been developed upon the basis of the reduction of the protonated iminium form. The relationship between reduction peak current and concentration is linear up to at least 13 ppm. The reproducibility of the method in terms of relative standard deviation (RSD) was smaller than 1.6% for ten determinations, at a concentration level of 5.51×10^–6 and 2.62×10^–5 mol/l. A determination limit of 80 ppb was obtained.     

Micro-pumping flow system for spectrophotometric determination of anionic surfactants in water

A novel procedure has been developed for spectrophotometric determination of anionic surfactants in water using a solenoid micro-pump as fluid-propulsion device. The proposed method is based on substitution of methyl orange (MO) by anionic surfactants in the formation of an ion-pair with the cetyl pyridine ion (CPC⁺) at pH 5.0. The flow network comprised four solenoid micro-pumps which, under microcomputer control, enabled sample and reagent introduction, and homogenisation in the reaction zone. The system is flexible and simple to operate and control, and sensitive and precise. The analytical plot for the anionic surfactant was linear between 1.43×10^–6 and 1.43×10^–5 mol L^–1 (0.5 to 5.0 mg L^–1; R=0.997, n=5). The relative standard deviation was 0.8% (n=11) for a sample containing 5.74×10^–6 mol L^–1 (2 mg L^–1) surfactant. The limit of detection was 9.76×10^–8 mol L^–1 (0.034 mg L^–1) and the sampling throughput was 60 determinations per hour. The results obtained for washing-water samples were comparable with those obtained by use of the reference method, and no significant differences at the 95% confidence level were observed.     

Electrocatalytic Properties and Voltammetric Determination of Melatonin at a Nanostructured Film Electrode

A multi-wall carbon nanotube (MWNT) film coated glassy carbon electrode (GCE) was fabricated, and the electrochemical behavior of melatonin on the MWNT film coated GCE was investigated. The oxidation peak current of melatonin increases significantly and the oxidation peak position shifts positively at the MWNT film modified GCE compared to that at a bare GCE. This indicates that MWNTs feature highly effective catalysis to the electrochemical oxidation of melatonin. A simple and sensitive electroanalytical method was developed for the determination of melatonin. The oxidation peak current is proportional to the concentration of melatonin from 8×10^–8 to 1×10^–5molL^–1. The detection limit is about 2×10^–8molL^–1 for 3min accumulation. The proposed method was demonstrated to work satisfactorily with commercial capsules.     

Rapid determination of telmisartan in pharmaceuticals and serum by the parallel catalytic hydrogen wave method

The polarographic characteristics of telmisartan have been investigated in 0.8 mol L^–1 NH₃.H₂O–NH₄Cl (pH 8.9)–0.01 mol L^–1 H₂O₂ as supporting electrolyte. The results demonstrate that the polarographic reduction wave at ca. –1.30 V in the absence of H₂O₂ is a catalytic hydrogen wave, and the reduction wave enhanced by H₂O₂ is a so-called parallel catalytic hydrogen wave. The analytical sensitivity of the parallel catalytic hydrogen wave is ca. 60 times higher than that of the corresponding catalytic hydrogen wave. Based on the parallel catalytic hydrogen wave a novel method has been developed for determination of telmisartan by linear sweep polarography. The calibration curve is linear in the range 2.0×10^–8–2.0×10^–6 mol L^–1 and the detection limit is 1.0×10^–8 mol L^–1. The precision is excellent with relative standard deviations of 2.6% at a concentration of 1.0×10^–7 mol L^–1 telmisartan. The proposed method has been applied to the direct determination of the telmisartan in capsule forms and biological samples. The proposed method has been proved to be advantageous over existing CZE and MEKC methods in simplicity, rapidity, and reproducibility.     

Anodic stripping voltammetric determination of mercury using multi-walled carbon nanotubes film coated glassy carbon electrode

An electrochemical method for the determination of trace levels of mercury based on a multi-walled carbon nanotubes (MWNT) film coated glassy carbon electrode (GCE) is described. In 0.1 mol L^–1 HCl solution containing 0.02 mol L^–1 KI, Hg²⁺ was firstly preconcentrated at the MWNT film and then reduced at –0.60 V. During the anodic potential sweep, reduced mercury was oxidized, and then a sensitive and well-defined stripping peak at about –0.20 V appeared. Under identical conditions, a MWNT film coated GCE greatly enhances the stripping peak current of mercury in contrast to a bare GCE. Low concentrations of I^– remarkably improve the determining sensitivity, since this increases the accumulation efficiency of Hg²⁺ at the MWNT film coated GCE. The stripping peak current is proportional to the concentration of Hg²⁺ over the range 8×10^–10–5×10^–7 mol L^–1. The lowest detectable concentration of Hg²⁺ is 2×10^–10 mol L^–1 at 5 min accumulation. The relative standard deviation (RSD) at 1×10^–8 mol L^–1 Hg²⁺ was about 6% (n=10). By using this proposed method, Hg²⁺ in some water samples was determined, and the results were compared with those obtained by atomic absorption spectrometry (AAS). The two results are similar, suggesting that the MWNT-film coated GCE has great potential in practical analysis.     

Use of ICP and XAS to determine the enhancement of gold phytoextraction by <Emphasis Type="Italic">Chilopsis linearis</Emphasis> using thiocyanate as a complexing agent

Under natural conditions gold has low solubility that reduces its bioavailability, a critical factor for phytoextraction. Researchers have found that phytoextraction can be improved by using synthetic chelating agents. Preliminary studies have shown that desert willow (Chilopsis linearis), a common inhabitant of the Chihuahuan Desert, is able to extract gold from a gold-enriched medium. The objective of the present study was to determine the ability of thiocyanate to enhance the gold-uptake capacity of C. linearis. Seedlings of this plant were exposed to the following hydroponics treatment: (1) 5 mg Au L^–1 (2.5×10^–5 mol L^–1), (2) 5 mg Au L^–1+10^–5 mol L^–1 NH₄SCN, (3) 5 mg Au L^–1+5×10^–5 mol L^–1 NH₄SCN, and (4) 5 mg Au L^–1+10^–4 mol L^–1 NH₄SCN. Each treatment had its respective control. After 2 weeks we determined the effect of the treatment on plant growth and gold content by inductively coupled plasma–optical emission spectroscopy (ICP–OES). No signs of shoot-growth inhibition were observed at any NH₄SCN treatment level. The ICP–OES analysis showed that addition of 10^–4 mol L^–1 NH₄SCN increased the concentration of gold by about 595, 396, and 467% in roots, stems, and leaves, respectively. X-ray absorption spectroscopy (XAS) studies showed that the oxidation state of gold was Au(0) and that gold nanoparticles were formed inside the plants.     

Functionalised multi-walled carbon nanotubes-modified electrode for sensitive determination of Diuron in seawater samples

ABSTRACT

This work was focused in to develop an electroanalytical method based on a direct modification of a glassy carbon electrode (GCE) by the deposition of successive aliquots of diluted dispersions of functionalised carbon nanotubes (MWCNT-COOH) in ethanol (0.1 mg.mL^?1) aiming the determination of Diuron into seawater samples, a common antifouling substance, using differential pulse voltammetry as electroanalytical technique. The GCE/MWCNT-COOH showed a sensitivity of 2.20 μA/μmol L^?1 about 10 times higher than the unmodified counterpart (GCE) which showed a sensitivity of 0.192 μA/μmol L^?1. The limits of detection and quantificationwere 6.88 × 10^?8 and 2.29 × 10^?7 mol L^?1 for GCE/MWCNT-COOH while for GCE were 7.87 × 10^?7 and 2.62 × 10^?6 mol L^?1, respectively. The applicability was evaluated with spiked detectable amounts of Diuron into seawater samples. The recovery results were between 76% and 119%.     

A comparison of different types of gold–carbon composite electrode for detection of arsenic(III)

A study has been conducted using abrasively modified basal and edge-plane graphite, carbon-paste, and carbon–epoxy electrodes to create gold–carbon composite electrodes. Using either nano or micro-sized gold particles their suitability for use in detecting arsenic(III) is assessed. It was found that gold arrays prepared from micron-sized particles gave the best performance for arsenic detection. In particular micron arrays produced in carbon-paste electrodes with an easily renewable surface work well for detection of arsenic, producing a detection limit of 5(±2)×10^–9 mol L^–1, with a high sensitivity of 10(±0.1) A mol^–1 L.