Annealed Treatment Effect in Poly（3-hexylthiophene）：Methanofullerene Solar Cells

Polymer photovoltaic devices based on poly（3-hexylthiophene） （P3HT） ： [6,6]-phenyl-C61-butyricacid methyl ester （PCBM） 1：1 weight-ratio blend are reported. The effects of various annealing treatments on the device performance are investigated. Thermal annealing shows significant improvement of the device performances. For devices at 130℃ annealing, maximum power conversion efficiency （PCE） of 3.3% and All factor up to 60.3% is achieved under air mass 1.5, 100 m W/cm^2 illumination. We discuss the effect of thermal annealing by the results of ultraviolet-visible absorption spectroscopy （UV-vis）, dark current-voltage curve, atomic force microscopy （AFM）.     

非晶/结晶共混对聚合物光伏电池性能的影响

以局域规整聚（3-己基噻吩） （P3HT）制备了TiO₂/聚合物型双层结构光伏电池.利用稳态电流-电压测试和动态强度调制光电压谱,结合差热分析、吸收光谱和荧光光谱, 研究了非晶支化聚亚乙基亚胺（BPEI）作为P3HT膜层的添加成分对TiO₂/P3HT双层电池性能的影响.由于P3HT链的高结晶性,使得TiO₂/P3HT界面接触不好,导致电池性能差.当在P3HT中共混重量比W_BPEI/P3HT=1％—5％的BPEI时,电池性能得到显著改善;尤其是当W_BPEI/P3HT= 1％时,电池表现出近0.8V的开路电压和20μA/cm²的短路电流.结果表明BPEI对电池性能的影响不是源于P3HT-BPEI共混体系光学性能的变化,而主要是由于其改变了TiO₂/P3HT界面接触性能.BPEI对TiO₂/P3HT界面接触有两个相互竞争的影响,这取决于P3HT-BPEI共混体系的组成.一方面,通过降低P3HT的结晶度和增强与TiO₂表面的相互作用,改善P3HT链在TiO₂ 表面的附着;另一方面,当BPEI含量过高时,BPEI在TiO₂表面的附着量将增加,反而会阻碍P3HT与TiO₂表面的接触.良好的TiO₂/P3HT界面接触有利于提高激子的界面分离效率、光生电子的寿命和电池效率.本文结果有望为聚合物光伏电池性能的改善提供新的认识和方法. 关键词： 聚（3-己基噻吩） 二氧化钛 共轭聚合物 光伏电池     

Temperature Dependence of the Fluorescence Emission Intensity of Eu/TiO2 Nanocrystals

The samples of europium ions doped titanium dioxide （Eu^3＋/TiO2） nanocrystals are synthesized by a modified sol-gel method with hydrothermal treatment. The x-ray diffraction and scanning electron microscopy are used to characterize the sample. The temperature-dependent fluorescence emission effect of Eu^3＋-doped samples is investigated. It is found that under the excitation of 514.5nm light, the emission intensity of Eu^3＋ reaches a maximum value at 450K among various Eu^3＋ dopant concentrations in Eu^3＋ /TiO2 nanocrystals. The variation of the emission intensity may be attributed to the photon-assist absorption and the temperature-quenching effect.     

Enhanced Efficiency of Polymer： Fullerene Bulk Heterojunction Solar Cells with the Insertion of Thin TiO2 Layer near the LiF/A1 Electrode

The insertion layer of TiO2 between polymer-fullerene blend and LiF/AI electrode is used to enhance the shortcircuit current Isc and fill factor （FF）. The solar cell based on the blend of poly[2-methoxy-5-（2＇-ethylhexyloxy）- 1,4-phenylenevinylene] （MEH-PPV） and C60 with the modifying layer of TiO2 （about 20nm） shows the open- circuit Voc of about 0.62 V, short circuit current Isc of about 2.35 mA/cm^2, filling factor FF of about 0.284, and the power conversion efficiency （PCE） of about 2.4% under monochromatic light （50Onto） photoexcitation of about 17mW/cm^2. Compared to ceils without the TiO2 layer, the power conversion efficiency increases by about 17.5%. Similar effect is also obtained in cells with the undoped MEH-PPV structure of ITO/PEDOT：PASS/MEH- PPV/（TiO2）LiF/AI. The improved solar cell performance can be attributed to enhanced carrier extraction efficiency at the active layer/electrode interfaces when TiO2 is inserted.     

Effect of TiO2 Nanotubes on Polymer-Fullerene Bulk Heterojunction Solar Cells

We investigate the photovoltaic properties of hybrid organ/c solar cell based on the blend of poly[2-methoxy-5-（2- ethylhexoxy-l,4-phenylenevinylene） （MEH-PPV）, C60 and titanium dioxide （TiO2） nanotubes. In comparison of the composite devices with different TiO2：[MEH-PPV ＋C60] weight ratios of lw$.% （D1-1）, 2wt.% （D1-2）, 3wt.% （D1-3）, 5wt.% （D1-4）, 10wt.% （D1-5） and 20wt.% （D1-6）, it is found that the device Dl-a exhibits the best performance. The conversion efficiency is improved by a factor of 3 compared with the MEH-PPV：C60 device.     

Upconversion Luminescence of Er3+ Ions in Transparent Germanate Glass Ceramics Containing CaF2 Nanocrystals

The visible upconversion and near-infrared luminescence of Er3＋ ions in germanate glass ceramics containing GaF2 nanocrystals are investigated. The nanocrystals are characterized by x-ray diffraction （XRD） and transmission electron microscopy, showing their mean sizes less than 20hm. High transmittance of the glass ceramics is displayed by absorption spectra. The upconversion luminescence intensity in the glass ceramics increases significantly with increasing temperature. Both the shifts of the XRD peaks and the Stark-split shown in the luminescence spectra indicate the entrance of the Er3＋ ions into the CaF2 nanocrystals, which is confirmed by a Judd-Ofelt analysis. Possible mechanisms of the upconversion luminescence are analyzed.     

Investigation of polymer/inorganic hybrid photovoltaic device using quantum dots as the interface modifier

CdS quantum dots (QDs) were introduced as an interface modifier in the poly(3-hexylthiophene) (P3HT)/TiO₂ nanorod arrays hybrid photovoltaic device. The presence of CdS QDs interlayer was found to provide enhanced light absorption, increased interfacial recombination resistance at the P3HT/TiO₂ interfaces, thus leading to a lower recombination rate of the electrons due to the stepwise structure of band edge in P3HT/CdS/TiO₂, which accounts for the observed enhanced photocurrent and photovoltage of the hybrid solar cells. The optimized performance was achieved in P3HT/CdS/TiO₂ hybrid solar cells after deposition of CdS QDs for 10 cycles, with a power conversion efficiency of 0.57 %, which is nearly ten times higher than that of P3HT/TiO₂. The findings indicate that inorganic semiconductor quantum dots provide effective means to improve the performance of polymer/TiO₂ hybrid solar cells.     

Studies on stability of bi-functional P3HT:PCBM:rubrene optoelectronic devices

Investigations are carried out for stability in photovoltaic response of bifunctional electroluminescent and photovoltaic devices, based on ternary blend of poly(3-hexylthiophene) (P3HT), phenyl [6,6′]C₆₁ butyric acid methyl ester (PCBM), and 5,6,11,12-tetraphenylnaphthacene (rubrene). P3HT and PCBM are important and the most frequent materials used for photovoltaic applications, therefore, for relative comparison, photovoltaic cells were also prepared using a binary mixture of P3HT and PCBM. Devices based on the ternary blend exhibited better stability in all photovoltaic parameters and the lifetime was almost doubled, but their photovoltaic efficiency was lower than that of those based on the binary blend. Longer lifetime of ternary blend devices is because of a relatively better thermal, electrochemical, and morphological stabilities of the ternary blend system. However, the lower efficiencies are because of the reduced photo-current and low fill factor (FF) due to an increased recombination and introduction of defects/trapping sites by rubrene molecules.     

Direct imprinting of ordered and dense TiO2 nanopore arrays by using a soft template for photovoltaic applications

Highly ordered and dense TiO₂ nanopore arrays are directly nanoimprinted on a transparent conductive glass substrate by using a polymethylmethacrylate/polydimethylsiloxane (PMMA/PDMS) composite soft template, which is replicated from an anodic aluminum oxide (AAO) replica mold. Results indicate that heat infiltration under vacuum conditions can ensure complete filling of PMMA into the AAO pores, and that free-standing PMMA nanorods with an aspect ratio more than 5 can be obtained by adjusting the AAO pore depth based on a freeze-drying technique. TiO₂ nanopore arrays with different diameters from 30 to 300 nm and inter-pore distances between 70 and 450 nm can be easily fabricated by using the corresponding templates with different sizes. Preliminary solar cells are also assembled with a heterojunction of conjugated polymer/TiO₂ nanopore arrays. Results indicate that the construction of poly-(3-hexylthiophene) (P3HT)/TiO₂ nanopore arrays can be more helpful in quenching the PL emission of P3HT than that of P3HT/flat TiO₂ film, and a maximum efficiency of about 0.32% can be obtained for a photovoltaic device with a TiO₂/[6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM)/P3HT structure.     

Structural and Magnetic Properties of Fe-Doped Anatase TiO2 Films Annealed in Vacuum

Structural and magnetic properties of Fe-doped anatase TiO2 films fabricated by sol-gel spin coating are investigated. X-ray diffraction measurements reveal that Fe^3＋ ions are incorporated into the TiO2 lattice. No ferromagnetism-related secondary phases and magnetic nanopaxticles are observed in the films. The presence of electron paramagnetic resonance signals at 9- 2.0 supports oxygen vacancies and/or defects generated in the films after annealing in vacuum. Magnetic measurements indicate that Fe-doped anatase TiO2 films are ferromagnetic at room temperature. These observations suggest that oxygen vacancies and/or defects axe energetically favorable for the long range Fe^3＋-Fe^3＋ ferromagnetic coupling in Fe-doped anatase TiO2 films.     

Morphology effects in nanocrystalline CuInSe<Subscript>2</Subscript>-conjugated polymer hybrid systems

We investigated blends of poly hexylthiophene (P3HT) with copper indium diselenide nanocrystals for photovoltaic applications. Depending on the synthesis, the particles were shielded by different organic surfactants. Different concentrations of these nanoparticles were suspended in the polymer solutions and spin cast onto ITO glass. Morphological studies have been performed by atomic force microscopy and transmission electron microscopy. Films consisting of tri-n-octylphosphine oxide-capped CISe:P3HT show photovoltaic response. The best performance we obtained is an open-circuit voltage of about 1 V and a photocurrent of 0.3 mA/cm² using a white light illumination intensity of 80 mW/cm². PACS 78.66.Sq     

A Charge-Trap Memory Device with a Composition-Modulated Zr-Silicate High-k Dielectric Multilayer Structure

We report a novel charge-trap memory device with a composition-modulated Zr-silicate high-k dielectric mul- tilayer structure prepared by using the pulsed laser deposition technique. The device employs amorphous （ZrO2）0.5（SiO2）0.5 as the tunneling and blocking oxide layers, and ZrO2 nanocrystals as the trapping storage layer. Zr02 nanocrystals are precipitated from the phase separation of （ZrO2）0.5（SiO2）0.2 films annealed at 800℃, and isolated from each other within the amorphous （ZrO2）0.5（SiO2）0.5 matrix. Our charge trapping device shows a memory window of 2.6 V and a stored electron density of 1×10^13/cm2.     

Influence of cationic stoichiometry of the bottom electrode La1-xSrxCoO3 on the microstructures of Pb(Ta0.05Zr0.48Ti0.47)O3 ferroelectric films using Pt/TiO2 conducting barrier

The heterostructures La_1-xSr_xCoO₃/Pb(Ta_0.05 Zr_0.48Ti_0.47)O₃(PTZT)/La_1-x Sr_xCoO₃ have been deposited on SiO₂/Si(001) substrates using Pt/TiO₂ as conductive barrier by pulsed-laser deposition. La_0.25Sr_0.75CoO₃(25/75) bottom electrodes with a pseudo-cubic perovskite structure favors (001)-textured growth of PTZT films. The ferroelectric capacitor LSCO(25/75)/PTZT/LSCO(25/75) remains about 96% of its polarization after 5᎒¹⁰ switching cycles at an applied voltage of 5 V and a frequency of 500 kHz. The cross-section morphology of scanning electron microscopy and Rutherford backscattering spectra show that no obvious interdiffusion occurs across the interfaces.     

Synthesis and application of the solar cell of poly(3-hexylthiophene)/Fe N/titanium dioxide nanocomposite material

A series of nanocomposites of poly(3-hexylthiophene) with Fe N-doped TiO₂ (P3HT/Fe N/TiO₂) were synthesized by the chemical method in situ. The structure of the prepared composites was characterized using X-ray diffraction patterns (XRD), infrared spectroscopy (IR), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). Optical and electrochemical properties were determined using UV-vis spectroscopy, fluorescence spectroscopy, and cyclic voltammetry. These tests indicated that P3HT/Fe N/TiO₂ is a new p-n semiconductor. Two solar cells based on P3HT/Fe N/TiO₂ were manufactured and studied.     

Electronic Structure and Optical Properties of La-Doped SrTiO3 and Sr2TiO4 by Density Function Theory

The effect of La doping on the electronic structure and optical properties of SrTiO₃ and Sr₂TiO₄ is investigated by the first-principles calculation of plane wave ultrasoft pseudopotential based on the density function theory (DFT). The calculated results reveal that the electron doping in the case of Sr_0.875La_0.125TiO₃ and Sr_1.875La_0.125TiO₄ can be described within the rigid band model. The La³⁺ ions fully acts as electron donors in Sr_0.875La_0.125TiO₃ and Sr_1.875La_0.125TiO₄ systems and the Fermi level shifts further into the conduction bands (CBs) for Sr_1.875La_0.125TiO₄ compared to Sr_0.875La_0.125TiO₃. The two systems exhibit n-type degenerate semiconductor features. At the same time, the density of states (DOS) of the two systems shift towards low energies and the optical band gaps are broadened. The Sr_1.875La_0.125TiO₄ is highly transparent with the transmittance about 90% in the visible range, which is larger than that of Sr_0.875La_0.125TiO₃(85%). The wide band gap, small transition probability and weak absorption due to the low partial density of states (PDOS) of impurity in the Fermi level result in the optical transparency of the films...     

Synthesis, structure and optical properties of Eu/TiO2 nanocrystals at room temperature

The nanocrystal samples of titanium dioxide doped with europium ion (Eu³⁺/TiO₂ nanocrystal) are synthesized by the sol-gel method with hydrothermal treatment. The Eu³⁺ contents (molar ratio) in the samples are 0, 0.5%, 1%, 2%, 3% and 4%. The X-ray diffraction, UV-Vis spectroscopy data and scanning electron microscope image show that crystallite size is reduced by the doping of Eu³⁺ into TiO₂. Comparing the Raman spectra of TiO₂ with Eu³⁺/TiO₂ (molar ratio Eu³⁺/TiO₂=1%, 2% and 4%) nanocrystals at different annealing temperatures indicates that the anatase-to-rutile phase transformation temperatures of Eu³⁺/TiO₂ nanocrystals are higher than that of TiO₂. This is due to the formation of Eu-O-Ti bonds on the surface of the TiO₂ crystallite, as characterized by the X-ray photoelectron spectroscopy. The photoluminescence spectra of TiO₂ in Eu³⁺/TiO₂ nanocrystals are interpreted by the surface self-trapped and defect-trapped exciton relaxation. The photoluminescence of Eu³⁺ in Eu³⁺/TiO₂ nanocrystals has the strongest emission intensity at 2% of Eu³⁺ concentration.     

Pulsed-laser deposition of Ta-doped PZT ferroelectric films for memory applications using conductive oxide La0.25Sr0.75CoO3 and SrRuO3 electrodes

New methods for fabricating highly 𘚡¢-oriented and complete 𘜏¢-textured Pb(Ta_0.05Zr_0.48Ti_0.47)O₃ (PTZT) films on Pt/TiO₂/SiO₂/Si(001) substrates by pulsed-laser deposition have been developed using conductive oxide La_0.25Sr_0.75CoO₃ and SrRuO₃ electrodes. The 𘚡¢-preferred orientated PTZT ferroelectric capacitor was not subjected to loss of its polarization after 1᎒¹⁰ switching cycles at an applied voltage of 5 V and a frequency of 1 MHz, and the 𘜏¢-textured PTZT film capacitor retains 94.7% of its polarization after 1.5᎒¹⁰ switching cycles at 5 V and 50 kHz. The PTZT capacitors using these conductive oxide electrodes have low leakage current dominated by Schottky field emission mechanism.     

Structural and electrical properties of La0.5Sr0.5CoO3 films on SrTiO3 and porous a-Al2O3 substrates

Films of La_0.5Sr_0.5CoO₃ (LSCO) have been deposited on specially treated TiO₂-terminated (001) SrTiO₃ substrate surfaces and on macroporous polycrystalline !-Al₂O₃ substrates, having a mean pore diameter of 80 nm, by pulsed laser deposition. The films deposited on SrTiO₃ are good conducting, (001) textured, and exceptionally smooth (1-2 Å for 100 nm thick films). LSCO films deposited on porous !-Al₂O₃ are polycrystalline and exhibit good crystallographic and electrical properties despite the large substrate roughness and the differences in lattice parameters and crystal structure between the film and the substrate. Different growth modes have been observed on the porous !-Al₂O₃ substrates depending on the oxygen pressure during film deposition. Films grown at an oxygen pressure of 10^-1 mbar are macroporous, whereas films grown at 10^-2 mbar completely cover the substrate pores. In the latter case, strain effects lead to film cracking.     

The inverted solar cells with the polymer:fullerene blend film possessing a stratified composition profile

The inverted polymer:fullerene solar cells with structure of ITO/TiO₂/P3HT:PCBM/MoO₃/Al have been fabricated, where P3HT and PCBM stand for poly (3-hexylthiophene) and [6,6]-phenyl C₆₁-butyric acid methyl ester, respectively. It is discovered that the P3HT:PCBM blend film manipulated into the improved stratification structure, characterized as P3HT crystallite-rich zone close to the top surface and PCBM constituent-rich zone adjacent to the bottom surface, can offer nearly the same power conversion efficiency of solar cell, compared to the one grown into the bulk heterojunction structure, characterized as the bicontinuous interpenetrating network of P3HT and PCBM. We provide an alternative insight to the morphology control of inverted polymer:fullerene solar cells.     

PRODUCTION OF A 3－+ GLUEBALL IN J/ψ RADIATIVE DECAY

The multiple angular-correlation function for the sequential decays J/ψ→γ+G(3^－+), G(3^－+)→M₁M₂, where G is a J^pc=3^－+ state and M₁ and M₂ are spinless mesons, is deduced. A 3^－+ glueball state is discussed and the ratios of the helicity amplitudes of J/ψ→γ+G(3^－+) are calculated. One ratio is independent of the glueball's mass and very small.