Oxygen defect dependent variation of band gap,Urbach energy and luminescence property of anatase,anatase–rutile mixed phase and of rutile phases of TiO2 nanoparticles

TiO₂ nanoparticles are prepared by a sol–gel method and annealed both in air and vacuum at different temperatures to obtain anatase, anatase–rutile mixed phase and rutile TiO₂ nanoparticles. The phase conversion from anatase to anatase–rutile mixed phase and to rutile phase takes place via interface nucleation between adjoint anatase nanocrystallites and annealing temperature and defects take the initiate in this phase transformation. The samples are characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV–vis and photoluminescence spectroscopy (PL). Anatase TiO₂ exhibits a defect related absorption hump in the visible region, which is otherwise absent in the air annealed samples. The Urbach energy is very high in the vacuum annealed and in the anatase–rutile mixed phase TiO₂. Vacuum annealed anatase TiO₂ has the lowest emission intensity, whereas an intense emission is seen in its air annealed counterpart. The oxygen vacancies in the vacuum annealed samples act as non-radiative recombination centers and quench the emission intensity. Oxygen deficient anatase TiO₂ has the longest carrier lifetime. Time resolved spectroscopy measurement shows that the oxygen vacancies act as efficient trap centers of electrons and reduce the recombination time of the charge carriers.     

Effect of Nb doping on morphology,crystal structure,optical band gap energy of TiO2 thin films

Nb–TiO₂ nanofibers and thin films were prepared using a sol–gel derived electrospinning and spin coating, respectively, by varying the Nb/Ti molar ratios from 0 to 0.59 to investigate the effect of Nb doping on morphology, crystal structure, and optical band gap energy of Nb–TiO₂. XRD results indicated that Nb–TiO₂ is composed of anatase and rutile phases as a function of Nb/Ti molar ratio. As the Nb/Ti molar ratio rose, the anatase to rutile phase transformation and the reduction in crystallite size occurred. The band gap energy of Nb–TiO₂ was changed from 3.25 eV to 2.87 eV when the anatase phase was transformed to rutile phase with increasing the Nb doping. Experimental results indicated that the Nb doping was mainly attributed to the morphology, the crystal structure, the optical band gap energy of Nb–TiO₂, and the photocatalytic degradation of methylene blue.     

Structural transformation study of TiO2 nanoparticles annealing at different temperatures and the photodegradation process of eosin-Y

Hydrothermal method was used to prepare TiO₂ nanoparticles with annealing temperature at 500 °C–700 °C. The mixture of anatase-rutile phase was investigated by powerful tool of X-ray diffraction (XRD). The structural parameters of anatase and rutile mixture phaseTiO₂ nanoparticles were calculated from the Rietveld refinement. The transformation rate of rutile was increased linearly with an annealing temperature of 500 °C–700 °C. The spherical morphology of the anatase and rutile mixed phase were obtained by scanning electron microscope and transmission electron microscope. The spherical particle of the anatase and rutile TiO₂ shows with great aggregation with different size and within the range of few tens nm. The EDAX study revealed the presence of titanium and oxygen. The best photocatalytic activity was identified as the 87.04% of anatase and 12.96% of rutile mixer phase of TiO₂. Various factors could be involved for a better photocatalytic activity.     

Titanium dioxide-coated nanofibers for advanced filters

This article reports on titanium dioxide (TiO₂)-coated nanofibers deposited on a filter surface by the electrospinning process. After depositing a micrometer-thick film of polyamide 11 nanofibers on polypropylene fabric, TiO₂ nanoparticles can be directly electrosprayed onto the nanofibers. X-ray diffraction and Raman spectroscopy showed minimal change in the phase composition (anatase and rutile) and no change in the particle size of nanocrystalline TiO₂ after coating. Scanning electron microscopy demonstrated that nanofibers were uniformly coated by titanium dioxide nanoparticles without agglomeration. TiO₂-coated filters showed excellent photocatalytic-bactericidal activity and photo-induced hydrophilicity.     

Integration of individual TiO2 nanotube on the chip: Nanodevice for hydrogen sensing

Titania (TiO₂) exists in several phases possessing different physical properties. In view of this fact, we report on three types of hydrogen sensors based on individual TiO₂ nanotubes (NTs) with three different structures consisting of amorphous, anatase or anatase/rutile mixed phases. Different phases of the NTs were produced by controlling the temperature of post‐anodization thermal treatment. Integration of individual TiO₂ nanotubes on the chip was performed by employing metal deposition function in the focused ion beam (FIB/SEM) instrument. Gas response was studied for devices made from an as‐grown individual nanotube with an amorphous structure, as well as from thermally annealed individual nanotubes exhibiting anatase crystalline phase or anatase/rutile heterogeneous structure. Based on electrical measurements using two Pt complex contacts deposited on a single TiO₂ nanotube, we show that an individual NT with an anatase/rutile crystal structure annealed at 650 °C has a higher gas response to hydrogen at room temperature than samples annealed at 450 °C and as‐grown. The obtained results demonstrate that the structural properties of the TiO₂ NTs make them a viable new gas sensing nanomaterial at room temperature. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Raman study of phase transformation of TiO2 rutile single crystal irradiated by infrared femtosecond laser

Titanium dioxide (TiO₂) rutile single crystal was irradiated by infrared femtosecond (fs) laser pulses with repetition rate of 250 kHz and phase transformation of rutile TiO₂ was observed. Micro-Raman spectra show that the intensity of E_g Raman vibrating mode of rutile phase increases and that of A_1g Raman vibrating mode decreases apparently within the ablation crater after fs laser irradiation. With increasing of irradiation time, the Raman vibrating modes of anatase phase emerged. Rutile phase of TiO₂ single crystal is partly transformed into anatase phase. The anatase phase content transformed from rutile phase increased to a constant with increasing of fs pulse laser irradiation time. The study indicates the more stable rutile phase is transformed into anatase phase by the high pressure produced by fs pulse laser irradiation.     

Effect of thermal annealing on the structure and microstructure of TiO2 thin films

Nanostructured TiO₂ thin films have been prepared through chemical route using sol-gel and spin coating techniques. The deposited films were annealed in the temperature range 400–1000°C for 1 h. The structure and microstructure of the annealed films were characterized by GAXRD, micro-Raman spectroscopy and AFM. The as-deposited TiO₂ thin films are found to be amorphous. Micro-Raman and GAXRD results confirm the presence of the anatase phase and absence of the rutile phase for films annealed up to 700°C. The diffraction pattern of the film annealed at 800 to 1000°C contains peaks of both anatase and rutile reflections. The intensity of all peaks in micro-Raman and GAXRD patterns increased and their width (FWHM) decreased with increasing annealing temperature, demonstrating the improvement in the crystallinity of the annealed films. Phase transformation at higher annealing temperature involves a competition among three events such as: grain growth of anatase phase, conversion of anatase to rutile and grain growth of rutile phase. AFM image of the asdeposited films and annealed films indicated exponential grain growth at higher temperature.      

Phase transition and thermodynamic properties of TiO2 from first-principles calculations

The pressure induced phase transitions of TiO2 from anatase to columbite structure and from rutile to columbite structure and the temperature induced phase transition from anatase to rutile structure and from columbite to rutile structure are investigated by ab initio plane-wave pseudopotential density functional theory method(DFT),together with quasi-harmonic Debye model.It is found that the zero-temperature transition pressures from anatase to columbite and from rutile to columbite are 4.55 GPa and 19.92 GPa,respectively.The zero-pressure transition temperatures from anatase to rutile and from columbite to rutile are 950 K and 1500 K,respectively.Our results are consistent with the available experimental data and other theoretical results.Moreover,the dependence of the normalized primitive cell volume V/V0 on pressure and the dependences of thermal expansion coefficient α on temperature and pressure are also obtained successfully.     

Investigation on SERS of different phase structure TiO2 nanoparticles

In this paper, anatase and rutile TiO₂ nanoparticles as well as their mixed crystal phase structure TiO₂ nanoparticles were synthesized by a sol‐hydrothermal method, and were served as active substrates for surface‐enhanced Raman scattering (SERS) study. The results show that the 4‐mercaptobenzoic acid probe molecules exhibit different degree SERS enhancements on the surface of different phase structure TiO₂ nanoparticles. The mixed crystal structure TiO₂ with an appropriate proportion of anatase and rutile phase is favourable to SERS enhancement of adsorbed molecules. These are mainly attributed to the contributions of the TiO₂‐to‐molecule charge transfer mechanism and the mixed crystal effect. Copyright © 2015 John Wiley & Sons, Ltd.     

Enhanced photocatalytic performance of TiO2 particles via effect of anatase–rutile ratio

In the present work anatase–rutile transformation temperature and its effect on physical/chemical properties as well as photocatalytic activity of TiO₂ particles were investigated. The characterisation of the synthesised and annealed TiO₂ particles were determined by X-Ray Powder Diffraction (XRD), scanning electron microscope (SEM), dynamic light scattering (DLS) and Brunauer–Emmett–Teller surface area analysis (BET). The refraction in the ultraviolet–visible (UV–vis) range was assessed using a dual-beam spectrophotometer. The photocatalytic performance of the particles was tested on methylene blue solution. The XRD data indicated that the percentage of rutile increased with the annealing temperature and almost 100% of anatase transformed to rutile at 1000 °C. In addition, the phase transformation was a linear function of annealing temperature so phase composition of TiO₂ can be controlled by changing the annealing temperature. The SEM and BET results presented the increase of agglomerate size and the decrease of specific surface area with the increasing annealing temperature. This proved that anatase has smaller particle size and higher surface area than rutile. The photocatalytic activity of the annealed TiO₂ powders reduced with the increase of annealing temperature. The samples annealed at 900 °C and 925 °C with anatase: rutile ratio of 92:8 and 77:23, respectively, showed the best activity. These results suggested that the photocatalytic activity of TiO₂ particles is a function of phase composition. Thus it can be enhanced by changing its phase composition which can be controlled by annealing temperature.     

An investigation of phase transformation of titania slag using microwave heating

The influences of microwave heating on the phase transformation of titania slag were systematically investigated. The thermal stability, surface chemical functional groups and microstructure of the titania slag before and after microwave heating, at a temperature of 950?°C for 60 min, were also analyzed using thermogravimetry and differential thermal analysis (TG-DSC), Fourier transform infrared spectroscopy (FT-IR) spectrum and scanning electron microscope (SEM), respectively. The TG-DSC analysis revealed that the phase transformation of the titania slag from anatase TiO₂ to rutile TiO₂ occurred between 750 and 1000 °C. The FT-IR rustles demonstrate that the banding form of Ti⁴⁺, Ti³⁺ and Ti²⁺ ions and the methyl groups on the surface of the titania slag has changed and a new chemical bond Ti–OH was formed. The results of SEM showed that a large number of regulation rutile TiO₂ crystals were found on the surface of the microwave-treated samples and the synthetic rutile has been synthesized successfully using microwave heating.     

Structural characterizations of sol–gel synthesized TiO2 and Ce/TiO2 nanostructures

Mixed phase TiO₂ and Ce/TiO₂ samples were synthesized by a sol–gel method using different hydrolysis conditions. In pure TiO₂ samples, traditional X-ray diffraction (XRD) and Ti K-edge synchrotron X-ray absorption near edge structures (XANES) independently revealed their anatase/rutile phase ratios. XANES results further revealed a substantial amount of Ti atoms existed in other forms beside anatase and rutile TiO₂ in the sample synthesized by the low hydrolysis condition. An increase in the extent of the hydrolysis during the synthesis leads to an increased rutile ratio and a reduction in other forms. In Ce/TiO₂ samples, the crystal sizes were too small for XRD characterization. Only XANES could be used to characterize their phase ratios. It is found that adding Ce impedes rutile formation; leading to increased anatase ratio. The difference in the fundamental aspects of XRD and XANES techniques in providing the phase ratios is discussed.     

甲醇分子在金红石TiO2(110)和锐钛矿TiO2(001)表面吸附和反应的活性位点

通过高分辨的扫描隧道显微术研究并比较了金红石型TiO₂(110)-(1×1)和锐钛矿型TiO₂(001)-(1×4)两种表面的活性位点． 在金红石型TiO₂(110)-(1×1)表面, 观察到氧空位缺陷是O₂和CO₂分子的活性吸附位点,而五配位的Ti原子是水分子和甲醇分子的光催化反应活性位点．在锐钛矿型TiO₂(001)-(1×4)表面,观察到完全氧化的表面,Ti原子更可能是六配位的,H₂O和O₂分子均不易在这些Ti原子上吸附．经还原后表面出现富Ti的缺陷位点, 这些缺陷位点对H₂O和O₂分子表现出明显的活性． 锐钛矿型TiO₂(001)-(1×4)表面的吸附和反应活性并不具有很高的活性,某种程度上其表现出的活性似乎低于金红石型TiO₂(110)-(1×1)表面．     

Effect of Ag doping on the crystallization and phase transition of TiO2 nanoparticles

TiO₂ nanoparticles doped with different Ag contents were prepared by a modified sol–gel method, using titanium tetraisopropoxide and silver nitrate as precursors and 2-propanol as solvent. Silver was incorporated into the TiO₂ matrix via decomposition of AgNO₃ during thermal treatment in different atmospheres. Effects of Ag doping on the crystallization and phase transition of the TiO₂ nanoparticles were studied using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Raman spectroscopy techniques. While air annealing incorporates silver into TiO₂ matrix in silver oxide form, annealing in nitrogen incorporates metallic silver into TiO₂. Formation of silver oxide increases the thermal stability of the TiO₂ particles. Silver oxide affects the crystallization process of TiO₂ particles and the temperature of transition form anatase to rutile. On the other hand, presence of metallic silver in the samples annealed in nitrogen atmosphere decreases the temperature of phase transition of TiO₂ nanoparticles.     

热处理对爆轰合成的纳米TiO_2混晶的结构相变的影响

采用爆轰法制备了纳米TiO2混晶体,初步研究了不同煅烧温度(600℃和720℃)和不同煅烧时间(1 h,2 h,3.5 h和5 h)对其微结构和结构相变行为的影响,并应用热动力学理论讨论了从锐钛矿相到金红石相的结构相变过程和相变机理.研究表明:随着煅烧温度的升高和煅烧时间的增加,纳米TiO2的粒径逐渐增大,混晶中金红石相的含量逐渐提高.与常规方法制备的纳米TiO2不同的是,在相同煅烧温度和煅烧时间下金红石相的平均生长速率明显低于锐钛矿相.锐钛矿相完全相变为金红石的温度也明显低于常规方法报道的相变温度.该研究会对控制纳米TiO2晶体尺寸和批量合成提供一定的理论和实验指导.     

Preparation and characterization of hollow TiO2 nanospheres: The effect of Fe3+ doping on their microstructure and electronic structure

Hollow Fe-doped TiO₂ spheres with various Fe dopant concentrations, 0.25, 0.50 and 1.0 wt%, were synthesized via a hydrothermal method using carbon spheres as templates. The prepared samples were calcined in air at temperatures of 500 and 550 °C for 3 h and characterized using XRD, SEM, TEM, SAED, EDX, XPS and UV–vis spectroscopy. The analytical results showed that the presence of a very low concentration of Fe³⁺ incorporated into hollow nanoporous TiO₂ spheres inhibited the growth of nanocrystals as well as the anatase to rutile phase transformation inside the anatase TiO₂ lattice. Doping with 1.0 wt% Fe³⁺ resulted in a reduction of the TiO₂ sphere diameter from 205.71 ± 25.29 nm to 68.70 ± 7.07 nm. The optical energy gap of the samples was determined from UV–Vis absorption spectra. The results showed that the absorption edge of TiO₂@Fe was shifted toward the visible light region with increased Fe content.     

Effect of annealing on TiO2 nanoparticles

TiO₂ nanoparticles have been prepared by simple chemical precipitation method and annealed at different temperatures. The as-prepared TiO₂ are amorphous, and they transform into anatase phase on annealing at 450 °C, and rutile phase on annealing at 900 °C. The X-ray diffraction results showed that TiO₂ nanoparticles with grain size in the range of 21–24 nm for anatase phase and 69–74 nm for rutile phase have been obtained. FESEM images show the formation of TiO₂ nanoparticles with small size in structure. The FTIR and Raman spectra exhibited peaks corresponding to the anatase and rutile structure phases of TiO₂. Optical absorption studies reveal that the absorption edge shifts towards longer wavelength (red shift) with increase of annealing temperature.     

Structural and thermoluminescence properties of undoped and Fe-doped-TiO<Subscript>2</Subscript> nanopowders processed by sol–gel method

In this study, we report on the nanocrystalline powders of TiO₂ and Fe-doped TiO₂ (anatase and rutile phases) prepared by sol–gel method. The X-ray diffraction and Raman spectroscopy measurements indicated the presence of anatase or rutile phase in nanopowders. TEM micrographs showed 10 and 112 nm average particle sizes for anatase and rutile, respectively. Furthermore, their thermoluminescence properties were analyzed.     

不同晶相结构和形貌TiO2负载Ru催化剂的CO选择甲烷化

用水热法得到的钛酸纳米纤维前体,通过不同后处理方法合成了多种纳米结构的TiO₂．采用N₂等温吸附和BET比表面、X射线衍射、透射电镜和能量分散X射线分析表征了TiO₂及负载Ru催化剂的微结构,包括比表面、晶相结构和形貌以及Ru纳米颗粒尺寸分布等．对负载Ru催化剂在富氢条件下CO选择甲烷化反应活性测试表明：金红石相TiO₂和TiO₂-B为载体负载的Ru催化剂比锐钛矿相TiO₂负载的Ru催化剂表现出更高的反应性能．其活性区别说明了不同晶相结构和形貌TiO₂载体与Ru纳米颗粒的相互作用存在差异．     

锐钛矿相和金红石相TiO2:Nb的光电性能研究

采用基于密度泛函理论的第一性原理计算了锐钛矿相和金红石相TiO₂:Nb的晶体结构、电子结构和光学性质. 结果表明, 在相等的摩尔掺杂浓度下(6.25%), 锐钛矿相TiO₂:Nb的导带底电子有效质量小于金红石相TiO₂:Nb, 且前者室温载流子浓度是后者的两倍左右, 即具有更大的施主杂质电离率, 从而解释了锐钛矿相TiO₂:Nb比金红石相TiO₂:Nb具有更优异电学性能的实验现象. 光学计算也表明锐钛矿相在可见光区有更大的透过率, 从而在理论上解释了锐钛矿相TiO₂:Nb比金红石相TiO₂:Nb更适于做透明导电材料的原因. 计算结果与实验数据能较好符合. 关键词： 2:Nb')" href="#">TiO₂:Nb 第一性原理 电子结构 光学性能