Electrochemical Oxidation of Epinephrine and Uric Acid at a Layered Double Hydroxide Film Modified Glassy Carbon Electrode and Its Application

Increasing attention has been paid to layered double hydroxide (LDH) film modified electrode attributing to its desirable properties for fabrication of electrochemical sensor. In this paper, the Zn‐Al LDH film modified glassy carbon electrode was characterized by electrochemical methods. The enhanced electrocatalytic currents and well‐separated potentials for epinephrine (EP) and uric acid (UA) were observed at the as‐prepared electrode. Under selected condition, the differential pulse voltammetry response of the modified electrode to EP (or UA) shows a linear concentration range of 0.5 μM to 0.3 mM (or 2 μM to 0.4 mM) in the presence of 10.0 μM UA (or 20.0 μM EP). At a signal‐to‐noise ratio of 3, the calculated limits of detection are 0.13 μM and 0.66 μM, respectively. The proposed method has been performed to successfully detect EP and UA in analysis of real samples, such as in EP injection solution and human urine samples.     

Electrogenerated Chemiluminescence Determination of Dopamine and Epinephrine in the Presence of Ascorbic Acid at Carbon Nanotube/Nafion‐Ru(bpy)$\rm{ {_{3}^{2+}}}$ Composite Film Modified Glassy Carbon Electrode

Based on the inhibition effect of dopamine and epinephrine on Ru(bpy) ‐tripropylamine electrogenerated chemiluminescence system, the excellent properties of carbon nanotube, and the cation permselectivity of Nafion film, an electrogenerated chemiluminescence inhibition method for determination of dopamine and epinephrine in the presence of ascorbic acid at carbon nanotube/Nafion‐Ru(bpy) composite film modified glassy carbon electrode was described. The results showed that the proposed method was sensitive and selective for the determination of dopamine and epinephine. The linear calibration range was from 1.6×10^?9 M to 3.2×10^?5 M and 5×10^?8 M to 6×10^?5 M for dopamine and epinephrine, respectively. 200‐fold excess of ascorbic acid did not interfere with the determination of 1 μM dopamine and epinephrine.     

Separation and determination of epinephrine and dopamine in traditional Chinese medicines by micellar electrokinetic capillary chromatography with laser induced fluorescence detection

A micellar electrokinetic capillary chromatography method with laser-induced fluorescence detection was developed for the analysis of epinephrine and dopamine after derivatization with 4-chloro-7-nitrobenzo-2-oxa-1,3-diazole. The optimum derivatization conditions were: 30 mM sodium borate (pH adjusted to 8.0 with 1.0 M HCl), reaction time 30 min at 60 degrees C. Baseline separation was achieved within 14 min with a running buffer composed of 10 mM sodium borate + 25 mM sodium dodecyl sulfate (pH adjusted to 9.5 with 0.1 M NaOH) and an applied voltage of 15 kV. Good linearity relationships (correlation coefficients: 0.9991 for epinephrine and 0.9985 for dopamine) between peak areas and concentrations of the analytes were obtained. The detection limits and quantification limits for epinephrine and dopamine were 0.0038 mg/L and 0.013 mg/L, and 0.065 mg/L and 0.020 mg/L, respectively. The method was applied to the analysis of the two compounds in two Chinese medicines with recoveries in the range of 92.6-108.7%.     

Selective Detection of Dopamine Using Glassy Carbon Electrode Modified by a Combined Electropolymerized Permselective Film of Polytyramine and Polypyrrole‐1‐propionic Acid

A sensitive and selective electrochemical method for the determination of dopamine using a combined electropolymerized permselective film of polytyramine and polypyrrole‐1‐propionic acid on a glassy carbon (GC) electrode was developed. The formation of a “layer‐by‐layer” film has allowed for selective detection of dopamine in the presence of 3,4‐dihydroxyphenylalanine (L‐DOPA), DOPAC, ascorbic acid, uric acid, epinephrine and norepinephrine. The modified electrodes exhibited a detection limit of 100 nM with linearity ranging from 5×10^?6 to 5×10^?5 M. No cleaning step was required during the course of repeated measurement.     

Sensitive and Facile Determination of Catechol and Hydroquinone Simultaneously Under Coexistence of Resorcinol with a Zn/Al Layered Double Hydroxide Film Modified Glassy Carbon Electrode

A stable dihydroxybenzene sensor was fabricated by electrochemical deposition of Zn/Al layered double hydroxide film on glassy carbon electrode (LDHf/GCE). The sensitive and facile electrochemical method for the simultaneous determination of catechol (CA) and hydroquinone (HQ) under coexistence of resorcinol (RE) has been achieved at the LDHf/GCE in phosphate buffer solution (pH 6.5). Under the optimized conditions, the differential pulse voltammetry response of the modified electrode to CA (or HQ) shows a linear concentration range of 0.6 μM to 6.0 mM (or 3.2 μM to 2.4 mM) with a correlation coefficient of 0.9987 (or 0.9992) and the calculated limit of detection is 0.1 μM (or 1.0 μM) at a signal‐to‐noise ratio of 3. In the presence of 50 μM isomer, the linear concentration ranges for CA and HQ are 3.0 μM to 1.5 mM and 12.0 μM to 0.8 mM, respectively. The detection limits are 1.2 μM and 9.0 μM. Further, the proposed method has been performed to successfully detect dihydroxybenzene isomers in analysis of real samples, such as water and tea.     

Electrocatalytic Oxidation and Determination of Sulfite with a Novel Copper‐Cobalt Hexacyanoferrate Modified Carbon Paste Electrode

The electrocatalytic oxidation of sulfite has been studied at a stable electroactive thin film of copper‐cobalt hexacyanoferrate (CuCoHCF) hybrid electrodeposited on a carbon paste electrode (ECMCPE). A linear range of 5 μM to 5 mM of sulfite, with an experimental detection limit of 1 μM, was obtained using the cyclic voltammetric method. The oxidation of sulfite showed no significant fouling effect on the modified electrode surface at sulfite concentrations below 5 mM. The proposed modified electrode exhibited several attractive features, including simple preparation, fast response, good stability and repeatability, and could be applied to sulfite determination in real samples.     

Simultaneous Determination of Epinephrine and Dopamine by Using Candida tropicalis Yeast Cells Immobilized in a Carbon Paste Electrode Modified with Single Wall Carbon Nanotube

A new electrochemical microbial biosensor system based on Candida tropicalis was developed for the fast detecting of dopamine and epinephrine. Candida tropicalis was immobilized in a carbon paste electrode (CPE) with single wall carbon nanotube (SWCNT). Immobilized cells were used as a origin of the polyphenol oxidase (PPO) to develop voltammetric epinephrine and dopamine biosensor. Voltammetric determination of phenolic compounds such as epinephrine and dopamine a simple technique which is available. Direct oxidation of phenols can be used, but the oxidation potentials of this compounds are similar and they can not be detected distinctively. Another possibility is the use of biosensors based on the polyphenol oxidase (tyrosinase) enzyme that oxidizes the phenolic compounds into their related quinones. By this way, phenolic compounds are epinephrine and dopamine which were used in this study as well detected at different potentials. In this study differential pulse voltammetry and amperometry techniques were used for the determination of dopamine and epinephrine. The effect of varying the amounts of SWCNT and the response of microorganism to epinephrine was investigated to find the optimum composition of the sensor. The effects of pH and temperature were also examined. Increases in biosensor responses obtained by amperometric measurements were linearly related to dopamine concentrations between 0.025 and 0.25 mM and epinephrine concentrations between 0.01 and 0.1 mM. Limits of detection of the biosensor for dopamine and epinephrine were calculated to be 0.008 and 0.0023 mM, respectively. Finally, proposed system was applied to epinephrine and dopamine analysis in pharmaceutical drugs and synthetic serum and the results were compared with LC MS MS method.     

Epinephrine Oxidation in the Presence of Interfering Molecules on Gold and Gold Electrodes modified with Gold Nanoparticles and Thiodipropionic Acid in Aqueous Solution. A Comparative Study

Thiodipropionoc acid (TDPA), cysteamine (CA) and gold nanoparticles (Au‐NPs) modified gold pure electrodes have been applied in voltammetric sensors for simultaneous detection of epinephrine (EP), ascorbic (AA) and uric (UA) acids. Modified electrodes with self assembled layers (SAMs) show high selectivity, sensitivity, reproducibility and stability. A linear relationship between the epinephrine concentration and the current response is obtained in the range of 0.1 μM to 0.65 μM with the detection limit ≤0.065 μM for the electrodes modified at 2D surface and in the range of 0.1 μM to 0.75 μM with the detection limit ≤0.082 μM for the electrodes modified at the 3D surface.     

维生素B1的电化学聚合及催化作用

用循环伏安法在石墨电极上制备了VB1聚合膜修饰电极,VB1聚合膜在pH5的PBS中有一对氧化还原峰,峰电位Epd=350mV,Epc=325mV,峰电流与扫描速率的平方根成正比,表明电子在膜中的传递为扩散控制,且聚合膜与VB1单体有不同的电化学性质。实验表明VB1聚合膜对多巴胺、肾上腺素等神经递质有显著的电催化作用。     

Gold-dendrimer Nanocomposite Based Electrochemical Sensor for Dopamine

An electrochemical sensor for dopamine was developed by electrodepositing poly(propylene imine) (PPI) dendrimer and gold nanoparticles (AuNPs) onto a glassy carbon electrode (GCE). Electrochemical characterisation of the sensor was carried out by cyclic voltammetry and electrochemical impedance spectroscopy in ferri/ferrocyanide electrolyte. The nanocomposite electrode (GCE-PPI-AuNPs) showed improved electroactive surface area and electrochemical response over bare GCE. The sensor recorded a detection limit of 0.16 μM over a concentration range of 0.1 μM to 125 μM. The sensor was applied for dopamine detection in human serum samples and in the presence of interfering substances such as ascorbic acid and epinephrine.     

RNA Modified Electrodes for Simultaneous Determination of Dopamine and Uric Acid in the Presence of High Amounts of Ascorbic Acid

A promising electrochemical biosensor was fabricated by electrochemical grafting of ribonucleic acid (RNA) at 1.8 V (vs. SCE) on glassy carbon electrode (GCE) (denoted as RNA/GCE), for simultaneous detection of dopamine (DA) and uric acid (UA) with coexistence of excess amount of ascorbic acid (AA). The electrode was characterized by X‐ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques. The RNA modified layer on GCE exhibited superior catalytic ability and anionic exclusive ability in comparison with the DNA modified electrode. Three separated anodic DPV peaks were obtained at 0.312, 0.168 and ?0.016 V for UA, DA and AA, respectively, at the RNA/GCE in pH 7.0 PBS. In the presence of 2.0 mM AA, a linear range of 0.37 to 36 μM with a detection limit of 0.2 μM for DA, and in the range of 0.74 to 73 μM with a detection limit of 0.36 μM for UA were obtained. The co‐existence of 5000 fold AA did not interfere with the detection of DA or UA. The modified electrode shows excellent selectivity, good sensitivity and good stability.     

Electrochemical Detection of Epinephrine Based on a Screen-printed Electrode Modified with NiO−ERGO Nanocomposite Film

This study presents a new electrochemical sensor (NiO−ERGO/SPE) for sensitive and selective detection of epinephrine (EPI) on the screen-printed electrode (SPE) which is modified with a nanocomposite film consisting of electrochemically reduced graphene oxide and NiO nanoparticles. After surface functionalization, structural and electrochemical characterization of NiO−ERGO film, DPV signals of NiO−ERGO/SPE towards the oxidation of EPI exhibited a linear correlation in the concentration range of 0.025 μM to 175 μM with a detection limit of 0.015 μM, which reveals NiO−ERGO film is manifested a good electrocatalytic activity for EPI detection compared with the previous reports. The selectivity of NiO−ERGO film was also tested on a very wide scale of possible interferents (ascorbic acid, uric acid, dopamine, lactic acid, phenylalanine, tyrosine, tryptophan, Li⁺, Na⁺, K⁺, Ca²⁺, and Zn²⁺). Moreover, to evaluate the applicability of the proposed sensor for real sample analysis, NiO−ERGO/SPE was successfully utilized for the determination of EPI in pharmaceutical samples.     

Preparation and Characterization of a Tin Pentacyanonitrosylferrate‐Modified Carbon Ceramic Electrode: Application to Electrocatalytic Oxidation and Amperometric Detection of L‐Cysteine

The sol‐gel technique was used to construct tin pentacyanonitrosylferrate (SnPCNF) modified composite carbon ceramic electrode (CCE). This involves two steps: construction of CCE containing metallic Sn powder and then electrochemical creating of SnPCNF on the surface of CCE. The SnPCNF modified CCE (SnPCNFlCCE) was characterized by energy‐dispersive X‐ray (EDX), FTIR and cyclic voltammetry (CV) techniques. The SnPCNF film showed electrocatalytic activity toward the oxidation of L ‐cysteine. A linear calibration plot was obtained over the L ‐cysteine concentration range 1–51 μM using chronoamperometry. L ‐cysteine was determined amperometrically at the surface of this modified electrode. The detection limit (for a signal to noise of 3) and sensitivity were found to be 0.62 μM and 126 μA/mM, respectively.     

Electrocatalytic Reduction of H2O2 and Oxygen on the Surface of Thionin Incorporated onto MWCNTs Modified Glassy Carbon Electrode: Application to Glucose Detection

A new H₂O₂ enzymeless sensor has been fabricated by incorporation of thionin onto multiwall carbon nanotubes (MWCNTs) modified glassy carbon electrode. First 50 μL of acetone solution containing dispersed MWCNTs was pipetted onto the surface of GC electrode, then, after solvent evaporations, the MWCNTs modified GC electrode was immersed into an aqueous solution of thionin (electroless deposition) for a short period of time <5–50 s. The adsorbed thin film of thionin was found to facilitate the reduction of hydrogen peroxide in the absence of peroxidase enzyme. Also the modified electrode shows excellent catalytic activity for oxygen reduction at reduced overpotential. The rotating modified electrode shows excellent analytical performance for amperometric determination of hydrogen peroxide, at reduced overpotentials. Typical calibration at ?0.3 V vs. reference electrode, Ag/AgCl/3 M KCl, shows a detection limit of 0.38 μM, a sensitivity of 11.5 nA/μM and a liner range from 20 μM to 3.0 mM of hydrogen peroxide. The glucose biosensor was fabricated by covering a thin film of sol–gel composite containing glucose oxides on the surface of thionin/MWCNTs modified GC electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The detection limit, sensitivity and liner calibration rang were 1 μM, 18.3 μA/mM and 10 μM–6.0 mM, respectively. In addition biosensor can reach 90% of steady currents in about 3.0 s and interference effect of the electroactive existing species (ascorbic acid–uric acid and acetaminophen) is eliminated. The usefulness of biosensor for direct glucose quantification in human blood serum matrix is also discussed. This sensor can be used as an amperometric detector for monitoring oxidase based biosensors.     

Electrochemiluminescence quenching as an indirect method for detection of dopamine and epinephrine with capillary electrophoresis

An electrochemiluminescence (ECL) inhibition method was developed as an indirect detection method for the determination of dopamine and epinephrine separated by capillary electrophoresis (CE). When the concentration of Ru(bpy)(3) (2+) was 50 muM diluted by 50 mM phosphate (pH 8.5) in the cell and 0.5 M tripropylamine (TPA) was added to the running buffer (10 mM phosphate, pH 9.0), an inhibition of ECL of the Ru(bpy)(3) (2+)/TPA system by the analytes was observed. Under the optimized conditions, the relative standard deviations of migration time and negative peak area were less than 1% and 3%, respectively, for 1 microM dopamine or 1 microM epinephrine (n = 10). Linear ranges of 0.1-10 microM for both analytes and the detection limits (signal-to-noise ratio S/N = 3) of 10 nM for dopamine and 30 nM for epinephrine were obtained.     

Facile Nonenzymatic Glucose Electrode Composed of Commercial CuO Powder and Ionic Liquid Binder

Commercially available micro-sized CuO powder was dispersed in the mixture of ethanol and protonated betaine bis((trifluoromethyl)sulfonyl)amide ([Hbet][TFSA]), a hydrophobic amide-type protic ionic liquid (IL), to prepare a composite paste for the modification of screen-printed carbon electrode (SPCE) via spin-coating. The fabricated SPCE\CuO−IL composite-based electrode showed a comparable activity as that of the nanonized metal-oxide based electrodes towards the electrochemical oxidation of glucose in alkaline solutions. Hydrodynamic chronoamperometry tests performed at +0.55 V showed a linear dynamic response of the electrode over the concentration range of 1 μM–2.8 mM with a sensor-sensitivity of 0.16 μA μM⁻¹ in 0.1 M NaOH. The data also showed a linear dynamic response over the concentration range of 1 μM–4.6 mM with a sensor-sensitivity of 0.10 μA μM⁻¹ in 0.1 M NaOH with 0.1 M NaCl, indicating that the major interferant Cl⁻ had negligible effects on glucose detection . Ascorbic acid (AA) (in the physiological level) and ethanol also did not interfere with the detection. Detection of glucose in real samples showed the recovery ratios higher than 95 %. This study has clearly demonstrated that commercial CuO powder without nanostructure can provide sufficient reactivity to the electrocatalytic oxidation of glucose by using IL as the organic binder. Facile preparation of the micro-sized metal oxide-modified electrodes can be accordingly pursued.     

Electrooxidation and Amperometric Detection of Ascorbic Acid at GC Electrode Modified by Electropolymerization of N,N‐Dimethylaniline

The polymer film of N,N‐dimethylaniline (DMA) is deposited on the electrochemically pretreated glassy carbon (GC) electrode by continuous electrooxidation of the monomer. This poly N,N‐dimethylaniline (PDMA) film‐coated electrode can be used as an amperometric sensor of ascorbic acid (AA). The polymer film (thickness (?): 0.3±0.02 μm) having positive charge in its backbone attracts the anionic species AA. Thus, the anodic peak potential (350 mV vs. Ag|AgCl|NaCl_(sat)) for the oxidation of AA at the bare electrode is largely shifted to the negative value (150 mV) at this electrode. The PDMA film‐coated electrode is stable in acidic, alkaline and neutral media and can sense AA at different pH's. The diffusion coefficients of AA in solution (D) and in film (D_s) were estimated by rotating disk electrode voltammetry: D=(5.5±0.1)×10^?6 cm² s^?1 and D_s=(6.3±0.2)×10^?8, (6.0±0.2)×10^?8 and (4.7±0.2)×10^?8 cm² s^?1 for 0.5, 1.5 and 3.0 mM AA, respectively. A permeability of AA through the PDMA film was found to decrease with increasing the concentration of AA in the solution. In the chronoamperometry, the current response for the oxidation of AA at different times elapsed after potential‐step application is linearly increased with the increase in AA concentration in a wide range of its concentration from 25 μM to 1.65 mM. In the hydrodynamic amperometry, a successive addition of 10 μM AA caused the successive increase in current response with equal amplitude and the sensitivity was calculated as 0.178 μA cm^?2 μM^?1. So, the fouling of the electrode surface caused by the oxidized product of AA is markedly eliminated at this PDMA film‐coated electrode. A flow injection analysis based on the present electrode was performed to estimate the concentration of vitamin C in fruit juice.     

Electrochemically Degraded Dopamine Film for the Determination of Dopamine

A dopamine (DA) polymer was deposited electrochemically on to a glassy carbon (GC) surface until the electrode surface was passivated. The DA film on the GC surface was re‐formed for high sensitivity and reproducibility by electrochemical degradation. The re‐formed electrode was sensitive and selective in the determination of DA in the presence of ascorbic acid. The linear range obtained by square‐wave voltammetry was between 0.1 and 2.1 μM (R=0.996, n=6) with a sensitivity of 1.2 μA μM^?1 and a detection limit (S/N=3) of 0.04 μM. The electropolymerized DA film was stable and the re‐formed electrode was reproducible for DA determination.     

Electrochemical Formation of Nanostructured Gold Surfaces on Glassy Carbon for the Determination of Dopamine

Nanostructured gold surfaces were prepared by potentiostatic, potentiodynamic or galvanostatic Au electrodeposition on glassy carbon electrodes. The nanostructured gold electrodes (nsAu/GC) were used for the determination of dopamine (DA) in aqueous media. A directly proportional relationship was found between the peak current for DA (obtained by square wave voltammetry, SWV) and its concentration for all cases. However, the best performance for DA determination was attained with potentiodynamically electrodeposited surfaces. The SWV peak current was linearly dependent on DA concentration up to 10 μM, with a detection limit (3σ) of 0.57 μM, and a correlation coefficient (r) of 0.9966. A study on the effect of common interfering species such as ascorbic acid (AA) and uric acid (UA) on DA determination was also carried out. The use of a nanostructured surface gives rise to peaks for AA and UA that appear at 0.15–0.20 V above the peak potential for DA. The detection limit obtained for dopamine is below 1 μM in the presence of 0.1 mM AA and 0.1 mM UA. Thus, nanostructuring of glassy carbon surfaces with gold conveniently and easily improves the detection of DA in the presence of their principal interfering species.     

The electrochemical properties of dopamine,epinephrine and their simultaneous determination at a poly(L-methionine) modified electrode

A poly(L-methionine) modified electrode, fabricated by electrochemical immobilization of the L-methionine on a glassy carbon electrode, was used for simultaneous determination of dopamine and epinephrine through cyclic voltammetry. The electrochemical properties of dopamine and epinephrine have been investigated. This sensor gave two separated cathodic peaks at −0.282 and 0.112 V for EP and DA, respectively. A linear response was obtained in the range of 5.0 × 10⁻⁷ to 1.0 × 10⁻⁴ mol l⁻¹ for epinephrine, and 1.0 × 10⁻⁶ to 5.0 × 10⁻⁴ mol l⁻¹ for dopamine. The detection limits were 3.6 × 10⁻⁷ mol l⁻¹ and 4.2 × 10⁻⁷ mol l⁻¹ for epinephrine and dopamine, respectively. This method was successfully applied for simultaneous determination of dopamine and epinephrine in human urines. The text was submitted by the authors in English.