基于LR305的平面荧光太阳能聚光波导研制

光伏发电是目前太阳能最佳的利用方式之一,但发电成本高。利用聚光结构提高光的转换和收集效率,是提高太阳能电池效率、减少电池用量、降低光伏发电系统成本的重要途径。以Lumogen F Red 305 (LR305) 染料作为荧光材料,将其掺杂到PMMA中,通过本体聚合法制作出尺寸为50 mm×50 mm×5 mm的PMMA平面荧光太阳能聚光波导,对其光学特性进行表征,同时将太阳能电池粘贴到聚光波导的输出端面,通过测试平面荧光太阳聚光波导对太阳能电池性能的影响研究了荧光太阳能聚光波导的聚光特性。     

准波导结构下染料薄膜的荧光光谱和放大自发辐射光谱特性

通过对RhB/PMMA和Rh6G/PMMA染料薄膜的荧光光谱和放大自发辐射(ASE)光谱的实验测量和理论分析,研究了准波导结构染料薄膜的荧光光谱和ASE光谱特性。实验上采用连续激光和脉冲激光照射,分别测量准波导结构RhB/PMMA和Rh6G/PMMA染料薄膜的荧光光谱和ASE光谱,发现荧光峰和ASE峰随着染料掺杂浓度和薄膜厚度的增加产生红移;理论上考虑准波导结构下薄膜中染料的自吸收效应,类比激光器谐振腔模型,分析低阶导模传输的增益特性,获得了荧光光谱与ASE光谱中荧光峰和ASE峰对应波长与染料掺杂浓度的关系,数值计算与实验测量相吻合。结果表明,准波导结构下薄膜中染料自吸收效应导致荧光峰及ASE峰发生红移,改变染料掺杂浓度,可以在较大调谐范围实现ASE。     

平板型太阳能聚光器的静力分析和模态分析

为了解决平板型太阳能聚光器因受力不均匀导致的聚光效率下降的问题,提出了以9块阵列透镜作为聚光模组的装配方式.设定聚光模组阵列与光波导板之间的空气间隙为2mm,通过ANSYS软件对聚光器进行线性静力分析和模态分析.设定风速为18m/s,高于指标等级14m/s,聚光器的模态分析基频为0.038s,满足结构刚度无需考虑动态影响的条件.讨论了结构组件在受到极限静风载的情况下,聚光模组与光波导板结构之间的位移变化和对应的前6阶的模态系数.结果表明:静力分析情况下聚光模组结构与光波导板之间的空气间隙最大位移为0.049mm,满足设计精度要求;在5种角度工况下,前6阶模态振型与施加预应力的模态振型相差在1%以内,且对应振型图形态类似,证明风载荷对于振型无影响.     

聚光光伏系统的发展及未来趋势

介绍了聚光光伏系统的发展历史和研究现状。对聚光光伏系统中的主件一聚光器和光伏电池进行了详细分类，给出了它们的特点和主要参数。描述了国外一些厂家为提高光伏系统效率并降低成本而研制的太阳跟踪系统。总结出聚光光伏系统的发展趋势，主要是指高倍聚光器＋跟踪系统和低倍大角度聚光器＋分光元件＋多节电池等。最后就目前状况提出了聚光光伏系统商业化还需要解决的问题。     

新型圆形吸收体太阳能复合抛物聚光器面形构建及光学分析

针对圆形吸收体提出了一种几何聚光比和可接收角同步提高的新型太阳能复合抛物聚光器(CPC),构建了新型CPC面形结构模型及数学解析解。对新型CPC的聚光性能进行了分析,并与常规CPC的光学性能进行了比较,结果表明:对于切线角相同的圆形吸收体新型CPC,随着圆形吸收体的直径增大时,面形起点的纵坐标值减小;当圆形吸收体直径和切线角分别为47 mm和5.56°时,面形起点的纵坐标为-29 mm;随着光口宽度角增大,新型CPC聚光器的几何聚光比减小,可接收角和平均光学效率随着光口宽度角的增大而增大;当光口宽度角为60°时,几何聚光比为1.16,可接收角为74.39°,平均光学效率为86.77%;新型CPC聚光器吸收体表面的能流分布较传统CPC更均匀。     

染料掺杂聚合物光纤的荧光及其光谱下转换性质

为了拓展染料掺杂聚合物光纤的应用范围,利用甲基丙烯酸甲酯(MMA)单体合成了掺有Coumarin540和Rhodamine 6G两种激光染料的聚甲基丙烯酸甲酯(PMMA)聚合物玻璃棒,并将其拉制成直径约1 000μm的聚合物光纤。以市售LED灯为光源,在侧向照明和前端照明两种条件下分别研究了染料掺杂的聚合物光纤中染料的荧光、荧光传输损耗以及光纤的光谱下转换等性质。两种染料的Stokes波长红移幅度分别达到70 nm和50 nm。在掺杂浓度分别为0.01 mg/g和0.04 mg/g时,侧向照明条件下测得两种光纤分别对520nm和577 nm的荧光的传输损耗为0.336 cm-1和0.343 cm-1。在前端照明条件下,在光纤输出端获得了较高下转换效率的光谱输出,其转换效率与染料掺杂浓度和光纤长度有关。这种染料掺杂的聚合物光纤有可能与石英玻璃光纤耦合,对其所传输的光进行光谱下转换的光频调控以更好地满足不同的应用需求。     

平板型太阳能聚光器的无漏光设计

针对平板型太阳能聚光器中出现的漏光问题,提出了无漏光聚光器的设计方法.该方法结合简单的数学计算与折射定律、反射定律推导出光线在光波导板中无漏光传播的最大距离理论公式,建立了无漏光聚光比与空气隙结构张角角度、主聚光器高度和宽度之间的数学模型,利用控制变量法分析了无漏光聚光比与各参数之间的关系.运用光线追迹软件对所设计的平板型无漏光太阳能聚光器进行光线追迹模拟,结果表明:在模拟光源选择存在0.27°的发散半角的太阳光源条件下,考虑光线在透射面处的菲涅耳损失和光学材料的吸收,在无漏光范围内实际最大聚光比达到698×、857×和1 032×时的聚光效率分别为88.2%、85.3%和80.2%;超过无漏光范围后随着聚光比进一步增大聚光效率下降较平缓.     

PbS量子点在荧光集光太阳能光伏器件上的应用

荧光集光太阳能光伏器件在平面光波导效应的作用下实现等效聚光,可以减少太阳能电池的用量,有效降低光伏发电的成本。将胶体化学法制备的吸收和发射在近红外波段的单分散球状PbS量子点荧光材料封装于两片光伏超白玻璃间的正己烷溶液中,构成溶液夹层封装的平面光波导,并和效率为17%的单晶硅太阳能电池耦合,制作出了吸收在700～1000nm,效率约为1.31%的近红外荧光集光太阳能光伏器件。     

基于银掺杂钠钙玻璃的荧光染料自发辐射增强

本文通过离子交换和后续热处理的方法在钠钙玻璃中引入Ag纳米颗粒, 并将Ag掺杂的钠钙玻璃作为衬底增强了钠钙玻璃和荧光染料罗丹明6G(R6G)的荧光辐射。Ag纳米颗粒的表面等离激元散射增强了掺杂玻璃的荧光, 而R6G的增强荧光辐射则源于掺杂玻璃与荧光染料之间的辐射共振能量转移。     

可折叠展开式伞状龙骨聚光器的聚光性能

针对可折叠展开式伞状龙骨聚光器具有自重低、功率高、比冲高、推力适中的特点,利用ANSYS和ZEMAX软件对功率为100 kW的可折叠展开式伞状龙骨聚光器在太空环境中的聚光性能进行模拟分析。在太阳风及衬底薄膜表面张力的影响下,伞面最大应力为1.66 MPa,远小于Kevlar材料及Ti-6Al-4V龙骨材料的阈值强度,伞面最大形变仅为0.941 mm,焦斑半径为6.37 cm,几何聚光比可达5 917,比标准抛物面仅减小了1.25%。结果表明:将材质轻、抗拉伸强度高的伞状龙骨结构引入可折叠展开式聚光器的设计方案,在很大程度上抵消了衬底薄膜材料表面张力及太阳风对聚光器工作形态的影响,可消除褶皱,提高可折叠展开式伞状龙骨聚光器的结构稳定性及可展开度,同时证明了伞状龙骨结构及Kevlar材料的选择是合理的。     

Effect of Host Medium on the Fluorescence Emission Intensity of Rhodamine B in Liquid and Solid Phase

In this work, we study the effect of concentration, host medium, PH and phase states on the fluorescence emission from the laser dye Rhodamine B pumped by UV laser as exited source. The polymethylmethacrylate PMMA is used as a host medium in case of solid phase samples while, ethanol and Tetrahydrofuran (THF) are used in case of a liquid one. Laser Induced Fluorescence (LIF) technique was used to study the fluorescence properties of both cases of liquid and thin film solid-state samples. In addition, the Dual Thermal Lens (DTL) technique was used to study the quantum yield of these samples. The concentrations of Rhodamine B in ethanol as solvent between 2 × 10⁻² M and 5 × 10⁻⁶ M were studied. The maximum fluorescence emission is observed at concentration of Rhodamine B C = 3 × 10⁻⁴ M. Comparison studies were investigated for different host medium such as ethanol, THF, PMMA in liquid phase state and PMMA in solid phase state. The measurements revealed that, the behavior of both phases state was analogous. Rhodamine B/PMMA thin film sample by ratio of 4:1 and thickness 0.12 mm was found to have the best photostability sample with a quantum yield about ≈0.82.     

Effect of secondary lens concentrators on the output parameters of solar modules with cascade photovoltaic converters

The feasibility of increasing the concentration ratio and expanding the misorientation curve using secondary lens elements is considered for solar modules with triple-junction InGaP/GaAs/Ge photovoltaic converters and radiation-concentrating Fresnel lenses. Composite glass-silicone Fresnel lenses measuring 40 × 40 and 60 × 60 mm (plan view) with focal lengths of 70 and 110 mm, respectively, are used as primary concentrators. The focal length of secondary plane-convex glass lenses is varied from 5 to 25 mm. With the shortest-focal-length secondary lenses used, measurements of the parameters of the photovoltaic converter in a system with radiation concentrators that were made with a pulsed solar tester show the increase in the concentration ratio and the expansion of the misorientation curve by a factor of 2.5–3.0. The parameters of test modules with lens panels measured under solar illumination are found to be in good agreement with laboratory data.     

Synthesis and luminescence properties of dye-doped deoxyribonucleic acid films

Dye-doped deoxyribonucleic acids (DNA)–tetradecyltrimethylammonium (TTA) films have been prepared. Rhodamine 6G, known as laser dyes, can be spontaneously doped by immersing the DNA–TTA film in rhodamine 6G-acetonitrile solutions. It is surmised that rhodamine 6G monomers and dimers diffuse within the hydrophobic TTA sites, and then monomers presumably intercalate between adjacent base pairs of DNA. Optical absorption spectra reveal that rhodamine 6G molecules in the sample undergo an unusual transformation from the dimer state to the monomer state with the elapse of time. Rhidamine 6G molecules doped in DNA–TTA show enhanced photostability and concentration quenching than those in PMMA. The environment, conformation and chemical stability of rhodamine 6G are different between DNA–TTA and PMMA, and are presumably modified by the intercalation.     

Enhancement of Raman scattering by deformation of microparticles

Raman scattering on deformed droplets levitated in an acoustic levitator and produced by a vibrating-orifice aerosol generator were investigated. Our samples experiments were diethyl hexyl sebecate (DEHS) droplets in the millimeter-size range and ethanol droplets in the size range 50-100 microm. The C-H stretching region from 2800 to 3100 cm(-1) was investigated. We found that the Raman intensity measured by a scattering angle of 90 degrees depended on the shape of the droplets. Raman scattering on spherical droplets was smaller than scattering on spheroidal droplets with the same volume. Similar results were observed for the fluorescence signal of Rhodamine 6G-doped DEHS droplets.     

石墨烯-银纳米颗粒复合结构制备工艺优化及表面增强拉曼光谱特性

在石墨烯-Ag纳米颗粒复合结构表面增强拉曼散射（SERS）基底常规制备工艺的基础上,提出了采用偶联剂吸附的方法来改善Ag纳米颗粒在目标基底上分布的均匀性;采用双层聚甲基丙烯酸甲酯（PMMA）来转移石墨烯,以减少石墨烯表面的缺陷;采用退火处理的方法来降低SERS基底的拉曼背景噪声,从而提高拉曼光谱的对比度。实验结果表明,采用优化制备工艺得到的复合结构SERS基底均匀性有较大提高,石墨烯G峰和2D峰的增强拉曼光谱对比度分别提高了54.9%和64.3%,罗丹明6G（R6G）分子在774和1 363 cm-1处的拉曼光谱强度随浓度变化关系的拟合优度（R2）分别达到了0.997 5和0.986 7。     

十二烷基硫酸钠(SDS)增强若丹明6G水溶液激光激发荧光谱研究

报道了若丹明6G水溶液添加不同浓度的表面活性剂十二烷基硫酸钠(SDS)时激光激发染料的变化,发现较低的掺入量导致R6G荧光减弱,适量SDS的加入使荧光增强,在5×10-5 mol·L-1的R6G水溶液中,加入6×10-2 mol·L-1 SDS,荧光增强因子达到3.1。当R6G浓度为1×10-4 mol·L-1时,加入2×10-2 mol·L-1,染料激光阈值显著降低。测量了不同浓度的R6G溶液的吸收光谱及加入不同浓度SDS后的荧光谱,分析了不同SDS加入量下R6G荧光减弱及增强的物理机制。     

Dependence of the solar cell performance on nanocarbon/Si heterojunctions

Solar cells that combine single-crystalline silicon(Si) with graphene(G) have been widely researched in order to develop next-generation photovoltaic devices. However, the power conversion efficiency(PCE) of G/Si solar cell without chemical doping is commonly low due to the relatively high resistance of graphene. In this work, through combining graphene with carbon nanotube(CNT) networks, we fabricated three kinds of hybrid nanocarbon film/Si heterojunction solar cells in order to increase the PCE of the graphene based Si solar cell. We investigated the characteristics of different nanocarbon film/Si solar cells and found that their performance depends on the heterojunctions. Specifically, a doping-free G-CNT/Si solar cell demonstrated a high PCE of 7.9%, which is nearly equal to the combined value of two individuals(G/Si and CNT/Si). This high efficiency is attributed to the synergistic effect of graphene and CNTs, and can be further increased to 9.1% after applying a PMMA antireflection coating. This study provides a potential way to further improve the Si based heterojunction solar cells.     

Tunable multiwavelength distributed-feedback zirconia waveguide lasers

Simultaneous tuning of multiple-output wavelengths was achieved in Rhodamine 6G-doped distributed-feedback zirconia waveguide lasers. As many as four separate output wavelengths were observed for a planar zirconia waveguide of 2.2-microm thickness. The laser output wavelengths corresponded to the propagation modes allowed in the planar waveguide. Continuous tuning by variation of the period of the optically generated grating was achieved from 584 to 611 nm.     

胶束中的若丹明6G荧光增强和激光行为

使用阴离子表面活性剂十二烷基硫酸钠 (SDS)有效的增强了若丹明 6G染料水溶液的荧光 ,在若丹明 6G浓度分别为 5 47× 10 -7和 5 47× 10 -4 mol·L-1时 ,最大增强比率分别为 1 95和 9 7。在后一浓度下SDS的加入使若丹明 6G染料激光阈值降低 ,能量转化效率提高。不加SDS时的激光阈值功率密度约为 6 5MW·cm-2 ,加入 4 1× 10 -2 mol·L-1的SDS后 ,激光阈值功率密度降为 0 8MW·cm-2 。泵浦光功率密度为 6 5MW·cm-2 时 ,能量转化效率达到 2 5 %。同时还观察到SDS的加入使溶液吸收谱、荧光谱和染料激光发生了红移。对以上现象的物理机制进行了讨论。