XAFS investigations of copper(II) complexes with tetradentate Schiff base ligands

X‐ray absorption fine structure spectra have been investigated at the K‐edge of copper in copper(II) salen/salophen complexes: [Cu(salen)] (1), [Cu(salen)CuCl₂].H₂O (2), [Cu(salophen)] (3) and [Cu(salophen) CuCl₂].H₂O (4), where salen^2? = N,N′‐ethylenebis (salicylidenaminato); salophen^2? = o‐phenylenediaminebis(salicylidenaminato). Complexes 1 and 3 are supposed to have one type of copper centers (called (Cu1)) and complexes 2 and 4 two types of copper centers (called (Cu1) and (Cu2)) having different coordination environments and geometries. A theoretical model has been generated using the available crystallographic data of complex 1 and it has been used for analysis of the extended X‐ray absorption fine structure (EXAFS) data of the four complexes to obtain the structural parameters for (Cu1) center. For this center, the obtained Cu–Cu distance (3.2 Å) verifies the binuclear nature of all the complexes. For determining the coordination geometry around (Cu2) center in 2 and 4, a theoretical model has been generated using the crystal structure of a Cu(II) complex, [Cu(C₁₆H₁₂N₂O₂Cl₂)]. This theoretical model has been fitted to the EXAFS data of 2 and 4 to obtain the structural parameters for (Cu2) center. The present analysis shows that (Cu1) center has square pyramidal geometry involving 2N and 3O donor atoms, whereas (Cu2) center has distorted tetrahedral geometry with 2O and 2Cl donor atoms. The values of the chemical shifts and presence of typical Cu(II) X‐ray absorption near‐edge spectroscopy features suggest that copper is in the +2 oxidation state in all these complexes. The intensity of ls → 3d pre‐edge feature has been used to investigate the geometry and binuclear nature of the complexes. Copyright © 2012 John Wiley & Sons, Ltd.     

空气隔离法流动注射在线预富集火焰原子吸收测定水样中的痕量铜和镉

研究了高效的在线流动注射编结反应器预富集火焰原子吸收系统直接测定水样中的痕量铜和镉。实验中将样品溶液和作为沉淀剂的氨水溶液输入编结反应器中,产生的铜和镉的氢氧化物沉淀被吸附在反应器壁内,然后通入一段空气流,再用硝酸洗脱并直接输送至火焰原子化器。在pH 5条件下,样品流速为4.4 mL·min-1,经90 s预富集,测定铜和镉的灵敏度分别提高34倍和36倍,检测限达1.9和0.3 μg·L-1。对铜和镉含量分别为30, 20 μg·L-1的溶液连续测定11次的相对标准偏差分别为2.3％和2.6％。此法用于饮用水和环境水样中痕量铜和镉的测定,获得了满意的结果。     

Excitation Mechanisms of Copper Ionic and Atomic Lines Emitted from a Low‐Pressure Argon Laser‐Induced Plasma

Abstract

Low‐pressure laser‐induced plasmas generated with a pulsed Nd∶YAG laser have complicated structures both temporally and spatially. The emission characteristics of the plasma are investigated for optimizing the experimental parameters in atomic emission spectrometry. The emission intensities of copper emission lines, measured in a time‐resolved as well as a time‐integrated mode, are strongly dependent on the kind of copper lines, ionic or atomic line, and the excitation energy. Also, the pressure of argon gas is the most important parameter for determining the behavior of these emission lines, including argon lines. Generally, copper ionic lines are dominantly emitted from the initial breakdown zone, because the copper ions are produced mainly in the hot breakdown zone. However, the Cu II 229.44‐nm line is emitted also from the expansion zone of the plasma. It results from an additional excitation process through the charge‐transfer collision particularly effective for the corresponding excited level. In this work, the excitation mechanisms for Cu I, Ar I, and Ar II lines are also discussed. The excitations occurring in the laser‐induced plasma can be well understood by taking the temporal and spatial variations in their intensities into consideration.     

X-Ray Photoelectron and Raman Spectroscopies,Comparative Studies of Supported Molybdenum Cobalt and Cobalt Molybdenum Catalysts

Laser Raman Spectroscopy is used to study catalysts : Co, Mo or Co-Mo supported on alumina. Well defined salts spectra are compared to those of these solids, which permits to establish superficial structures of cobalt, molybdenum or both.

For molybdenum catalysts, we found two structures depending upon the concentration

isolated MoO^2- ₄ molecular ions at low concentration < 4%

polymolybdate phase at higher concentration

For cobalt catalysts two structures are also observed: - tetrahedrally surrounded co ²+ ions at low concentration Co³O⁴ clusters at higher concentrations

For cobalt-molybdenum (8%) catalysts three cases occur no effect is observable at very low concentration of cobalt (0.5%)

a well defined compound appears for Co/Mo atomic ratio 0.25

when the cobalt concentration increases a third structure is observed but not identified

All these results are compared to X Ray photoelectron spectroscopic studies and are in good agreement with them.     

An atomistic study of grain boundary segregation and cracking

A Monte Carlo model is applied to study a Σ = 5 (310) fcc tilt boundary structure and impurity segregation to this boundary. The Johnson-type potential functions are used to express atomic interactions for two binary alloys of NiCu and CuSb systems. Through atomic relaxation near absolute zero, the basic structural unit of the Σ = 5 CSL boundary is found to dissociate into two subunits. For the NiCu system, copper segregation to the boundary follows the Gibbsian equilibrium segregation behavior in which the segregation is localized on a few atomic layers, its amount increases with increase in the bulk concentration but decreases with increase in temperature. For the CuSb system, an assumption of the CuCu bond weakening due to the strong, adjacent CuSb bonds is also incorporated to realize the embrittling effect of Sb atoms. The preferential site for the large Sb atoms is the vertex of a pentagonal bipyramid in the Σ = 5 grain boundary. Without bond weakening, the Sb-segregated grain boundary maintains a structure combined with a distorted pentagonal bipyramid and a capped trigonal prism. However, with bond weakening some bonds of the trigonal prisms are disrupted in order to form new pentagonal bipyramids. When a uniaxial strain is applied in the direction perpendicular to the grain boundary plane, the weakened copper bonds become the source of microcracks thus enhancing brittle fracture along the Sb-segregated grain boundary.     

Vibrational spectroscopic and force field studies of copper(II) chloride and bromide compounds,and crystal structure of KCuBr3

Vibrational spectroscopic and force field studies have been performed of 15 related copper(II) chloride and copper(II) bromide compounds, including hydrated salts crystallizing in ternary aqueous systems with alkali and ammonium halides. For halocuprates with distorted octahedral coordination characteristic stretching Raman wavenumbers, corresponding to symmetric stretching Cu^II X modes in the equatorial plane, were found in the ranges 247–288 cm⁻¹ for X = Cl, and 173–189 cm⁻¹ for X = Br, while the low‐wavenumber stretching modes for the weaker axial Cu X interactions varied considerably. The tetrahedral coordination for Cs₂CuCl₄ and Cs₂CuBr₄ leads to somewhat lower Cu X symmetric stretching wavenumbers, 295 and 173 cm⁻¹, respectively. The assignments of the copper–ligand stretching vibrations were performed with the aid of normal coordinate calculations. Correlations between force constants, averaged Cu X stretching wavenumbers and bond distances have been evaluated considering the following aspects: (1) Jahn–Teller tetragonal distortion (axial elongation) of the octahedral copper(II) coordination environment, (2) differences between terminal and bridging halide ligands (3) effects of coordinated water and the influence of outer‐sphere cations. Force constant ratios for terminal and bridging metal–halide bonds reveal characteristic differences between planar and tetrahedrally coordinated M₂X₆ species. In the hydrated copper(II) halide complexes, the halide ligands are more strongly bound than coordinated water molecules. The crystal structure of KCuBr₃ (K₂Cu₂Br₆), which was determined to provide structural information for the force field analyses, contains stacks of planar dimeric [Cu₂Br₆]²⁻ complexes held together by weak axial Cu Br interactions. Copyright © 2007 John Wiley & Sons, Ltd.     

Inferring unresolved hyperfine structure in liquid solution EPR:14N hyperfine structure in the 1∶1 copper-calcimycin complex

Theoretical expressions for EPR line widths in liquids suggest the following two strategies for inferring unresolved hyperfine structure in near square planar copper(II) complexes and thereby identify the coordinating ligand atoms: (i) Increasing the resolution by reducing the line widths, by forming a mixed ligand complex of lower magnetic anisotropy. (ii) By demanding that the magnetic anisotropy determined from line widths, assuming unresolved hyperfine structure, should agree with that determined from frozen solution EPR spectrum.¹⁴N hyperfine structure from a coordinating cal (A _N ～ 12 G) in 1∶1 copper-calcimycin complex (Cu?cal) has been observed / inferred by the application of these strategies in 1∶1 chloroform-ethanol mixtures. It has been suggested that Cu?cal prepared in the presence of the bidentate ligand diethyldithiocarbamate (dtc^?) is the mixed ligand complex Cu(dtc)(cal) in which cal is a bidentate ligand. The Cu?cal prepared in the presence of a monodentate anion AN (AN=NO ₃ ^? , Br^?, Cl^? etc.) is Cu(AN)(cal) in which cal is a tridentate ligand. These complexes have near planar coordination geometry.     

X-ray absorption investigations of copper resinate blackening in a XV century Italian painting

Investigations of the darkening phenomenon of copper resinate observed in a XV century easel painting were carried out by X-ray absorption spectroscopy (XAS) at the GILDA beamline of the European synchrotron radiation facility (ESRF, Grenoble, France). X-ray absorption near edge structure and extended X-ray absorption fine structure (EXAFS) measurements were collected at the Cu K-edge on an original painting sample, as well as on fresh pigment standards and on painting models. The study was aimed at providing structural information of the oxidation states and the local chemical environment (neighbouring atoms and bond distances) of copper in the unaltered and blackened pigments in order to elucidate the discoloration mechanism. Complementary information on optical and molecular properties of copper resinate were obtained by UV-vis and Fourier transform infrared spectroscopies. EXAFS analysis evidenced that the local chemical environment of Cu in copper resinate can be described using neutral copper acetate as a model. It consists, essentially, of bimetal Cu²⁺ carboxylate complexes with a distorted octahedral coordination. Such a structure is retained in the blackened pigment, although some differences were observed. It has been found that the alteration takes place without change of the valence state of Cu(II) ions, while the formation of the copper oxides CuO and Cu₂O responsible for the embrownment is excluded. On the basis of the XAS results we deduced that discoloration of copper resinate may be related to local modification of the copper coordination structure as evidenced by the observation of an increase of the Cu–Cu and Cu–C distances in the EXAFS spectra. PACS  78.70.Dm; 61.10.Ht     

A systematic neutron diffraction study of RBa2Cu3O7 (R=yttrium and rare earths) high-T c superconductors

The 10K crystal structures of high-T _c RBa₂Cu₃O₇ (R=Y and rare earths) ceramic materials investigated by neutron diffraction were consistently analysed concerning systematic trends. Several interionic distances exhibit the well known lanthanide contraction behaviour, i.e., a linear relationship with the ionic radii of trivalent rare-earth ions. The only exceptions are associated with the apex oxygen O(1) ions: the chain copper Cu(1)–O(1) distances are constant, and the plane copper Cu(2)–O(1) distances are increasing across the rare-earth series. For R=Pr the 4f–CuO₂ valence band hybridization effects are found to be highly anisotropic, since exclusively the interionic distances involving the b-direction (i.e, the chain direction) indicate that the Pr ions have an intermediate valence of about+3.4.     

Nano-scale copper oxidation on leadframe surface

Copper oxidation studies were carried out by means of field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS) and electron energy loss spectroscopy (EELS) techniques. The growth of copper oxide occurs as a copper surface comes in an oxygen containing environment. The reaction sequence leading to oxidation of the copper surface is generally accepted to be oxygen chemisorption, nucleation and growth of the surface oxide and bulk oxide growth. HRTEM examination of the cross section of the oxidized copper sample revealed the interface region in between the copper and copper oxide. At high oxidation temperature, formation of micro-voids and separations were observed along this interface region. Poor adhesion at this interface region due to micro-voids and separation were found to be the root cause of delamination issue. EELS analysis determined that for regions with intact interface the oxidation system is Cu/CuO/Cu₂O/CuO, however, in regions containing micro-voids or separation it is found to be Cu/Cu₂O/CuO.     

Atomic diffusion in annealed Cu/SiO2/Si（100） system prepared by magnetron sputtering

Cu thin films are deposited on p-type Si (100) substrates by magnetron sputtering at room temperature. The inter-face reaction and atomic diffusion of Cu/SiO2/Si (100) systems are studied by x-ray diffraction (XRD) and Rutherford backscattering spectrometry (RBS). Some significant results can be obtained. The onset temperature of interdiffusion for Cu/SiO2/Si(100) is 350 C. With the annealing temperature increasing, the interdiffusion becomes more apparent. The calculated diffusion activation energy is about 0.91 eV. For the Cu/SiO2/Si (100) systems copper silicides are not formed below an annealing temperature of 350 C. The formation of the copper silicides phase is observed when the annealing temperature arrives at 450 C.     

X-ray absorption study of Cu,Zn SOD under high pressure

Abstract

We have investigated Cu, Zn Superoxide Dismutase (Cu, Zn SOD) metal sites at high pressure using X-ray absorption. XAS (X-ray Absorption Spectroscopy) gives information on local structure and it is particularly suited to metal site investigation. To the best of our knowledge, this is the first time that protein conformational states have been investigated using the high pressure XAS technique. Cu, Zn SOD catalyses the dismutation of toxic oxygen radicals produced in cells; this reaction occurs at the copper metal site. Structural changes around the copper, induced by pressure, can be directly related to protein substates. Their characterisation is thus important in the understanding of protein activity.

The high-pressure device was a Paris-Edinburgh large volume cell.

Experiments were performed on lyophilised Cu, Zn SOD between 0 and 48 kbar at the copper and zinc K-edges. The two metal local atomic environments have a different behaviour as pressure increases: copper exhibits a more flexible environment; on the contrary, zinc shows small structural modifications. We have identified a state, formed between 3 and 8 kbar, which is stable up to 48 kbar.     

Effect of laser irradiation on the structure and valence states of copper in Cu-phosphate glass by XPS studies

The effect of laser irradiation using three different wavelengths (IR, visible and UV) generated from Nd:YAG laser on the local glass structure as well as on the valence state of the copper ions in copper phosphate glass containing CuO with the nominal composition 0.30(CuO)-(0.70)(P₂O₅), has been investigated by X-ray photoelectron spectroscopy (XPS). The presence of asymmetry and satellite peaks in the Cu 2p spectrum for the unirradiated sample is an indication of the presence of two different valence states, Cu²⁺ and Cu⁺. Hence, the Cu 2p_3/2 spectrum was fitted to two Gaussian-Lorentzian peaks and the corresponding ratio, Cu²⁺/Cu_total, determined from these relative areas clearly shows that copper ions exist predominately (>86%) in the Cu²⁺ state for the unirradiated glass sample under investigation. For the irradiated samples the symmetry and the absence of satellite peaks in the Cu 2p spectra indicate the existence of the copper ions mostly in Cu⁺ state. The O 1s spectra show slight asymmetry for the irradiated as well as unirradiated glass samples which result from two contributions, one from the presence of oxygen atoms in the P-O-P environment (bridging oxygen BO) and the other from oxygen in an P-O-Cu and PO environment (non-bridging oxygen NBO). The ratio of NBO to total oxygen was found to increase with laser power.     

Liquid-crystalline dendrimer Cu(II) complexes and Cu(0) nanoclusters based on the Cu(II) complexes: An electron paramagnetic resonance investigation

New nanostructured materials, namely, the liquid-crystalline copper(II) complexes that contain poly(propylene imine) dendrimer ligands of the first (ligand 1) and second (ligand 2) generations and which have a columnar mesophase and different copper contents (x = Cu/L), are investigated by EPR spectroscopy. The influence of water molecules and nitrate counterions on the magnetic properties of complex 2 (x = 7.3) is studied. It is demonstrated that water molecules can extract some of the copper ions from dendrimer complexes and form hexaaqua copper complexes with free ions. The dimer spectra of fully hydrated complex 2 (x = 7.3) are observed at temperatures T < 10 K. For this complex, the structure is identified and the distance between the copper ions is determined. It is shown that the nitrate counterion plays the role of a bridge between the hexaaqua copper(II) complex and the dendrimer copper(II) complex. The temperature-induced valence tautomerism attended by electron transport is revealed for the first time in blue dendrimer complexes 1 (x = 1.9) with a dimer structure. The activation energy for electron transport is estimated to be 0.35 meV. The coordination of the copper ion site (NO₄) and the structural arrangement of green complexes 1 (x = 1.9) in the columnar mesophase are determined. Complexes of this type form linear chains in which nitrate counterions serve as bridges between copper centers. It is revealed that green complexes 1 (x = 1.9) dissolved in isotropic inert solvents can be oriented in the magnetic field (B ₀ = 8000 G). The degree of orientation of these complexes is rather high (S _z = 0.76) and close to that of systems with a complete ordering (S _z = 1) in the magnetic field. Copper(0) nanoclusters prepared by reduction of complex 2 (x = 7.3) in two reducing agents (NaBH₄, N₂H₄ · H₂O) are examined. A model is proposed for a possible location of Cu(0) nanoclusters in a dendrimer matrix.     

Ultrasound-electrospinning-assisted fabrication and sensing evaluation of a novel membrane as ultrasensitive sensor for copper (II) ions detection in aqueous environment

The present study has reported an optimized fabrication and application of a novel PVA/TEOS/Schiff base nanofibers membrane as a highly sensitive copper (II) ions in aqueous environment. Here in, for first time, an ultrasound-assisted synthesized symmetric Schiff base has been immobilized on a hybrid polyvinyl alcohol (PVA) and TEOS using electrospinning technique for detection and filtration of copper ions. For this purpose, various working parameters were evaluated and finally the optimized nano fibers membrane was synthesized with 72 nm thickness and PVA/TEOS/Schiff base ratio of (wt%) 8:6:1. The optimized sample named PTLNFM has been employed successfully as an ultra sensitive chemosensor for Cu (II) detection in real samples. The immobilized Schiff base used as a chelating agent could detect copper (II) in the range from 9.34 × 10⁻⁸ to 1.15 × 10⁻⁵ mol L⁻¹ with the following correlation equation: Absorbance = 0.066 [Cu²⁺] × 10⁻⁶ + 0.095 and R² = 0.992 and LOD of 1.27 × 10⁻⁸ mol L⁻¹ which was lower than most of the reported detection limits in the previous literatures. Validity of this method has been carried out by analysis of Cu²⁺ in real samples with satisfying recoveries of over 96.11–99.24%.The developed membrane could be offered for diverse use such as medical or industrial applications.     

Solvent-tuned ultrasonic synthesis of 2D coordination polymer nanostructures and flakes

Herein, a new 2-dimensional coordination polymer based on copper (II), {Cu₂(L)(DMF)₂}_n, where L stands for 1,2,4,5-benzenetetracarboxylate (complex 1) is synthesized. Interestingly, we demonstrate that both solvent and sonication are relevant in the top-down fabrication of nanostructures. Water molecules are intercalated in suspended crystals of complex 1 modifying not only the coordination sphere of Cu(II) ions but also the final chemical formula and crystalline structure obtaining {[Cu(L)(H₂O)₃]·H₂O}_n (complex 2). On the other hand, ultrasound is required to induce the nanostructuration. Remarkably, different morphologies are obtained using different solvents and interconversion from one morphology to another seems to occur upon solvent exchange. Both complexes 1 and 2, as well as the corresponding nanostructures, have been fully characterized by different means such as infrared spectroscopy, x-ray diffraction and microscopy.     

Structure of New Bis-Dicarbollyl Derivatives of Transition Metals

The dipyridyl complexes of the copper salts of bis-o-dicarbollyliron(III), -cobalt(III), and -nickel(III) are investigated by means of EPR spectroscopy. Theoretical models of the EPR spectra of copper(II) ions in these complexes are constructed and their spectral parameters are determined. It is shown that in all cases the tetragonally distorted octahedron is the most probable coordination sphere of the Cu²⁺ ions.     

High oxygen pressures and the stabilization of a new mixed valence Cu(III)/Cu(IV)

Abstract

The Cu(III) oxides were investigated first for the unusual copper oxidation state and then for the high-Tc superconductivity. In the last case this property is observed when a mixed copper valence is stabilized : Cu(I)/Cu(II) or Cu(II)/Cu(III). A new mixed valence Cu(III)/Cu(IV) has been stabilized in the three dimensional lattice of the perovskite-type oxide Lal_-xSr_xCuO₃ (0 ≥ ′ ≥ 0,25). Chemical analysis and XPS study confirm the mixed valence. This compound shows metallic properties with an broadening of the conduction band compared to LaCu0₃. Such a behaviour can be explained either by the increase of the covalence of the average Cu-0 bond or by the decrease of the structural distortion induced by the substitution of Sr(II) for La(III). No superconducting property has been detected down to 4K.     

Peculiarities of crystal structures and magnetic properties of Cu(II) and Ni(II) mixed-ligand complexes on the 1,3-dithiole-2-thione-4,5-dithiolate basis

Mixed-ligand Cu(II) and Ni(II) complexes, [Cu(dmit)(bpy)]₂ (I), [Ni(dmit)(phen)₂] (II) and [Ni(dmit)(phen)₂]·CH₂Cl₂ (III) (dmit=1.3-dithiole-2-thione-4.5-dithiolate, phen=1.10-phenantroline, bpy=2.2′-bipyridine) have been prepared by ligand exchange between phen or bpy and (Bu₄N)₂[M(dmit)₂] (M=Ni, Cu) and characterized by elemental analysis, IR spectroscopy, single-crystal X-ray analysis and by investigation of magnetic and resonance properties. In complex I, the monomeric units form dimers in a head-to-tail arrangement by weak coordination bonds between copper and dithiolate sulfur atoms and π–π interactions between dmit and bpy from neighboring monomers. Dimers in I are further extended into chains by weak Cu–S(thione) contacts. In crystal packing of complex II and III, there exists a weak π–π interaction between two parallel phen molecules of the adjacent complexes. As a consequence, the magnetic and resonance characteristics of copper complex may be described in approximation of exchange-coupled pairs of Cu²⁺ ions with ion spin S=1/2. The nickel complexes are described by isotropic exchange model for single-site spin S=1.     

Cu(L-His)2溶液配位结构的X射线吸收精细结构分析

采用X射线吸收精细结构分析(XAFS)方法分析Cu(His)₂复合物的配位模式,通过测定不同pH值下的铜的K边XAFS吸收谱,研究Cu(His)₂第一配位壳层的结构．为了更准确地验证Cu(His)₂配位结构,对组氨酸的羧基和咪唑分别进行了化学修饰．研究结果明确了在不同pH环境下组氨酸的羧基、氨基和咪唑的配位情况．对于争议最大的在生理pH值下组氨酸的配位方式,其结果更支持六配位模式,同时可能有少量的五配位模式配合物平衡存在.