Surface Acidity of H-Birnessite: Infrared Spectroscopic Study of Formic Acid Decomposition

This paper presents the adsorption and thermal decomposition mechanism of formic acid on an H-birnessite sample. Changes in the surface and structure were characterized using infrared spectroscopy, N₂ gas adsorption–desorption, and thermal analysis techniques. The acid sites of H-birnessite were investigated by infrared and thermal analysis using pyridine as a molecular probe. Decomposition of formic acid started on H-birnessite at 120°C and was complete at 400°C. Infrared spectra revealed that the molecularly adsorbed formic acid species were transformed to a formate species, and the formate species were transformed to CO. The most stable adsorption structure for formic acid was found as a molecular monodentate configuration.     

Thermally stimulated luminescence from alkaline earth borates

The thermally stimulated luminescence from XB₂O₄ (X=Ca,Sr,Ba) has been investigated. The results on CaB₂O₄ and SrB₂O₄ are being reported here for the first time. In both cases, the emission is found to be quite intense, contrary to the case with BaB₂O₄. The presence of two peaks in the glow curves is noted over the temperature range of 300-570 K. The emission spectra corresponding to both the peaks have been observed to be identical, consisting of two broad emissions, one in the UV and other in the blue-green regions. The emission is apparently quite different from that of BaB₂O₄ in which case only very weak emission spreading over a broad wavelength range around 410 nm is observed. This result has been understood in terms of the overlap between the excitation and the emission spectra.     

PuO2和α-Pu2O3光学性质的经验势模拟

用GULP程序拟合出α-Pu₂O₃的Pu-O作用BMH经验势参数.结合氧离子壳模型势,运用分子静力学和动力学计算出PuO₂和α-Pu₂O₃理想晶体的结构参数和光学性质.结果显示：它们的空间群、晶胞参数、密度和熵等,与文献报道值接近,相对误差均小于1.2%;并计算出PuO₂和α-Pu₂O₃的高频和静态介电张量、红外介电函数谱、晶格振动 关键词： 2')" href="#">PuO₂ 2O₃')" href="#">α-Pu₂O₃ 光学性质     

Effects of RE2O3 (RE = Tm, Sc, Yb) addition on the superconducting properties of ErBa2Cu3Oy

We investigated the effects of added Tm₂O₃, Sc₂O₃, and Yb₂O₃ on the superconducting properties of sintered Er123 samples. Tm₂O₃ addition caused the least T_c degradation, exhibiting a T_c above 90 K even for 17 vol% addition. Samples with added Sc₂O₃ maintained a T_c at above 90 K up to an addition of 7.2 vol%, while Yb₂O₃-containing samples showed a monotonic decrease in T_c with increased vol% of added Yb₂O₃. Tm₂O₃-containing samples exhibited a slight increase in J_c(0.1 T)/J_c(0) and had constant J_c values even for 17 vol% addition. XRD and SEM results indicate that the Tm₂O₃ is very stable in the superconducting matrix.     

Solvothermal synthesis and characterization of α-Fe2O3 nanodiscs and Mn3O4 nanoparticles with 1,10-phenanthroline

α-Fe₂O₃ nanodiscs and Mn₃O₄ nanoparticles have been prepared by the 1,10-phenanthroline as complexing agent in the presence of sodium hydroxide under hydrothermal conditions. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared (FT-IR) spectra. The average diameter of α-Fe₂O₃ nanodiscs is of 2 μm. In the case of Mn₃O₄ sample, the Mn₃O₄ crystallites are nanoparticles with an average size of 34 nm. A formation mechanism for the α-Fe₂O₃ and Mn₃O₄ nanomaterials was proposed.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Nickel-induced magnetic behaviour of nano-structured α-Fe2O3, synthesised by facile wet chemical route

We report the synthesis of pristine and nickel containing iron oxide (α-Fe₂O₃) nanocrystallites by facile environmentally benign wet chemical process. The magnetic behaviour of the samples has been found to change progressively with nickel content. The Mössbauer spectra revealed the precipitation of secondary phase of nickel ferrite (NiFe₂O₄) at ～2?wt% nickel contents. The transmission electron micrographs together with asymmetric magnetic hysteresis loop have confirmed the formation of core–shell structure. The Morin temperature of nanostructured α-Fe₂O₃ as estimated by superconducting quantum interference device has been found to be 257, 245, 247 and 242?K at nickel content of 0, 1, 2 and 4?wt%, respectively. The similar trends of increase/decrease in Morin temperature have been noticed by Mössbauer analysis. Furthermore, below Morin temperature, the temperature range of coexisted antiferromagnetic and ferromagnetic states has been found to increase with increase in nickel content.     

Optical properties of La2O3 doped diamond-like carbon films

A novel kind of La₂O₃ doped diamond-like carbon (DLC) films with thickness of 100-120 nm were deposited by unbalanced magnetron sputtering. Raman spectra and photoluminescence properties were measured by Raman spectrometer operated by 325 nm He-Cd laser and 514 nm Ar⁺ laser, respectively. The intensities of Raman spectra and photoluminescence are higher than those of pure DLC films. The La₂O₃ doped DLC films have the potential promising for the application of solar cell coatings.     

Application of solid state track recorders for neutron spectra measurements in a reactor irradiation facility

Abstract

In connection with the IAEA-neutron seed irradiation Programme, a standard neutron irradiation facility has been constructed. The application of solid state track recorders for fast neutron spectra measurements inside this facility is discussed. Fissionable targets of ²³⁵U, ²³⁹Pu, ²³⁷Np, ²³⁸W and ²³²Th will be used, an approximative solution for the incident neutron spectrum will be obtained by a five-group method.     

Rotational dependences of line half-widths for CO and CO2 confined in SiO2/Al2O3 xerogel

The absorption spectra of CO and CO₂ confined in nanopores of SiO₂/Al₂O₃ xerogel have been measured using a Bruker IFS-125 HR Fourier spectrometer. Dependences of the half-width values on rotational quantum numbers and the line shift mean values are studied and compared with the data available in literature. Possible causes which can affect the rotational dependences are discussed.     

Development of rf plasma sputtered Al2O3-TiO2 multilayer broad band antireflecting coatings and its correlation with plasma parameters

TiO₂/Al₂O₃/TiO₂/Al₂O₃ multilayer structures were obtained at different oxygen:argon gas ratios of 20:80, 30:70, 50:50 and 60:40 sccm and constant rf power of 200 W using reactive magnetron sputtering. Grain size and elemental distribution in the films were studied from AFM image and XPS spectra respectively. The deposited grain size increased with increasing oxygen:argon gas ratio. The optical band gap, refractive index, extinction coefficient were calculated from UV-vis transmittance and reflectance spectra. It was observed that the value of refractive index, extinction coefficient and band gap increased with increasing oxygen. These variations are due to the defects levels generated by the heterostructure and explained by the PL spectrum. The antireflecting (AR) efficiency of the films was estimated from the reflectance spectra of the films. Broad band antireflecting coating for the visible range was achieved by varying oxygen content in the film. The plasma chemistry controlled the antireflecting property by the interface interdiffusion of atoms during layer transition in multilayer deposition. The in situ investigation of the plasma chemistry was performed using optical emission spectroscopy. The plasma parameters were estimated and correlated with the characteristics of the films.     

Preparation, electronic structure, and photocatalytic properties of Bi2O2CO3 nanosheet

Bi₂O₂CO₃ nanosheet with a thickness of less than 20 nm was synthesized via hydrothermal and solvothermal process. The properties of the as-prepared nanosheet were characterized by X-ray diffraction, scanning electron microscopy, and diffuse reflectance spectra. The electronic structure was investigated using first-principle calculations. Application of the as-prepared Bi₂O₂CO₃ nanosheet in photocatalysis was also studied.     

Investigations of oxide superconductors by x-ray absorption,photoemission and cognate spectroscopies

X-ray absorption spectra, X-ray photoelectron spectra and Auger spectra of cuprate superconductors are discussed. The studies establish the absence of Cu³⁺ for all practical purposes, but point out the importance of oxygen holes. X-ray photoelectron spectra of BaBi_0.25Pb_0.75O₃ and related compounds are also examined.     

Structural and optical properties of Er, Yb co-doped Y2O3 thin films

Thin Er³⁺, Yb³⁺ co-doped Y₂O₃ films were grown on (1 0 0) YAG substrates by pulsed laser deposition. Ceramic targets having different active ion concentration were used for ablation. The influence of the rare-earth content and oxygen pressure applied during the deposition on the structural, morphological and optical properties of the films were investigated. The films deposited at the lower pressure, 1 Pa, and at 1/10 Er to Yb doping ratio are highly textured along the (1 1 1) direction of the Y₂O₃ cubic phase. In addition to the crystalline structure, these films possess smoother surface compared to those prepared at the higher pressure, 10 Pa. All other films are polycrystalline, consisting of cubic and monoclinic phases of Y₂O₃. The rougher surface of the films produced at the higher-pressure leads to higher scattering losses and different behavior of the reflectivity spectra. Optical anisotropy in the films of less than 0.004 was measured regardless of the monoclinic structure obtained. Waveguide losses of about 1 dB/cm at 633 nm were obtained for the films produced at the lower oxygen pressure.     

Investigation on spectral features of tungsten ions in PbO-Bi2O3-As2O3 glass matrix

Lead bismuth arsenate glasses mixed with different concentrations of WO₃ (ranging from 0 to 6.0 mol%) were synthesized. Differential thermal analysis (DTA), optical absorption, ESR and IR spectral studies have been carried out. The results of DTA have indicated that there is a gradual decrease in the resistance of the glass against devitrification with increase in the concentration of WO₃ upto 4.0 mol%.The optical absorption spectra of these glasses exhibited a relatively broad band peaking at about 880 nm identified due to d_xy→d_x²_−y² transition of W⁵⁺ ions; this band is observed to be more intense in the spectrum of glass containing 4.0 mol% of WO₃. Further, two prominent kinks attributed to ³P₀→¹S₀, ¹D₂ transitions of Bi³⁺ ions have also been located in the absorption spectra. The ESR spectra of these glasses recorded at room temperature exhibited an asymmetric signal at g_⊥∼1.71 and g_ll∼1.61. The intensity of the signal is observed to be maximal for the spectrum of the glass W₄. The quantitative analysis of optical absorption and ESR spectral studies have indicated that there is a maximum reduction of tungsten ions from W⁶⁺ state to W⁵⁺ state in the glass containing 4.0 mol% of WO₃. The IR spectral studies have indicated that there is a increasing degree of disorder in the glass network with increase in the concentration of WO₃ upto 4.0 mol%.     

Spectroscopic Investigation of Tungsten Ions in Lead Scandium Phosphate Glass System

Lead scandium phosphate glasses (PbO-Sc₂O₃-P₂O₅) containing different concentrations of tungsten oxide (WO₃) ranging from 0 to 5 mol% were prepared. A number of studies, viz. differential thermal analysis (DTA), infrared spectra, optical absorption, and electron spin resonance (ESR) spectra, have been carried out. The results of DTA indicated the highest glass forming ability for the glass containing 5 mol% of WO₃. The results of spectroscopic studies have been analyzed in light of different oxidation states of tungsten ions.     

Preparation of photocatalytic Fe2O3-TiO2 coatings in one step by metal organic chemical vapor deposition

There are two major difficulties in the TiO₂ liquid-solid photocatalytic system: effective immobilization of the TiO₂ particles; and improving the catalytic activity under visible light. To simultaneously solve these two problems, Fe₂O₃-TiO₂ coatings supported on activated carbon fiber (ACF), have been prepared in one step by a convenient and efficient method—metal organic chemical vapor deposition (MOCVD). XRD results revealed that Fe₂O₃-TiO₂ coatings mainly composed of anatase TiO₂, α-Fe₂O₃ phases and little Fe₂Ti₃O₉. The pore structure of ACF was preserved well after loading with Fe₂O₃-TiO₂ coatings. UV-vis diffuse reflectance spectra showed a slight shift to longer wavelengths and an enhancement of the absorption in the visible region for Fe₂O₃-TiO₂ coatings, compared to the pure TiO₂ sample. A moderate Fe₂O₃-TiO₂ loading (13.7 wt%) was beneficial to mineralizing wastewater because the intermediates could be adsorbed onto the surface of photocatalyst following decomposition. The stable performance revealed that the Fe₂O₃-TiO₂ coatings were strongly adhered to the ACF surface, and the as prepared catalysts could be reused showing potential application for wastewater treatment.     

Effects of dopant concentrations on phosphorescence properties of Eu/Dy-doped Sr3MgSi2O8

Long afterglow Sr₃MgSi₂O₈: Eu, Dy phosphor with high brightness was prepared by sintering at high temperature and weak reductive atmosphere. The luminescent properties of this photoluminescent pigment were studied systematically by investigating concentration effects. The analytical results indicated that the main emission peaks appear at 482 nm. The excitation and emission spectra of this phosphor show that both of them are broadband. This is ascribed to the 4f⁷→4f⁶5d¹ transition of Eu²⁺ in the pigment matrix, which is in good agreement with the calculated value of 470 nm, and implies that luminescent centers Eu²⁺ occupy the deca-coordinated Sr²⁺ sites with the host of Sr₃MgSi₂O₈.     

H_3BO_3对Y_(1.98)O_3:Eu_(0.01),Dy_(0.01)红色长余辉发光材料结构和余辉性能的影响

采用高温固相法制备了发光样品Y1.98O3:Eu3+0.01,Dy3+0.01.采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、荧光光谱仪、单光子计数器测试了不同含量的H3BO3对Y1.98O3:Eu3+0.01,Dy3+0.01物相结构、颗粒形貌、发光性能、余辉性能的影响.结果表明当H3BO3含量低于8%(mol)时,样品可保持Y2O3晶格结构,且样品颗粒随H3BO3的含量增加逐渐增大.样品光致发光由Eu3+离子电子的5D0→7FJ跃迁所致,主峰位于612 nm,且发光强度随H3BO3含量的增加呈线性增强.随着H3BO3含量的增加,样品余辉衰减时间逐渐增加,热释光谱分析表明H3BO3的加入增加了基质陷阱能级的深度与浓度,故而导致样品长余辉性能的变化.     

Crystal structure and photoluminescence of (Y1−xCex)2Si3O3N4

Oxonitridosilicate phosphors with compositions of (Y_1−xCe_x)₂Si₃O₃N₄ (x=0−0.2) have been synthesized by solid state reaction method. The structures and photoluminescence properties have been investigated. Ce³⁺ ions have substituted for Y³⁺ ions in the lattice. The emission and excitation spectra of these phosphors show the characteristic photoluminescence spectra of Ce³⁺ ions. Based on the analyses of the diffuse reflection spectra and the PL spectra, a systematic energy diagram of Ce³⁺ ion in the forbidden band of sample with x=0.02 is given. The best doping Ce content in these phosphors is ∼2 mol%. The quenching temperature is ∼405 K for the 2 mol% Ce content sample. The luminescence decay properties were investigated. The primary studies indicate that these phosphors are potential candidates for application in three-phosphor-converted white LEDs.