A novel amperometric sensor for the detection of difenidol hydrochloride based on the modification of Ru(bpy)3 on a glassy carbon electrode

An amperometric sensor for the detection of difenidol, a tertiary amine-containing analyte, was proposed. Ruthenium(II) tris(bipyridine)/multi-walled carbon nanotubes/Nafion composite film was suggested to modify the glassy carbon electrode. The modified electrode was shown to be an excellent amperometric sensor for the detection of difenidol hydrochloride. The linear range is from 1.0 × 10⁻⁶ to 3.3 × 10⁻⁵ M with a correlation coefficient of 0.998. The limit of detection was 5 × 10⁻⁷ M, which was obtained through experimental determination based on a signal-to-noise ratio of three. The sensor was employed to the determination of the active ingredients in the tablets containing difenidol hydrochloride.     

Novel monohydrogenphosphate sensor based on vanadyl salophen

A novel PVC-based membrane sensor based on vanadyl salophen (VNSP) for determination of trace amounts of monohydrogenphosphate (MHP) ions is introduced. The electrode revealed Nernstian response towards monohydrogenphosphate over the wide concentration range from 1.0×10⁻¹ to 1.0×10⁻⁶ M at the pH of 8.2. The effect of solvent mediator, cationic additives and amount of ion-carrier on the behavior of the sensor was investigated. The sensor shows a short response time (<20 s) in the whole concentration ranges. The selectivity of the electrode is very high, and it can be used for detection of trace amounts of monohydrogenphosphate in the presence of large amounts of other anions. The detection limit of the electrode was 5.0×10⁻⁷ M (48 ng/ml) and it could be used for 14 weeks without any measurable changes in the slope. The potentiometric selectivity coefficients data revealed negligible interference from 16 common anions. It was successfully applied for the direct determination of monohydrogenphosphate in fertilizer samples and, as an indicator electrode, in potentiometric titration of HPO₄²⁻ ion with barium nitrate.     

The first use of a Rh(III) complex as a novel ionophore for thiocyanate-selective polymeric membrane electrodes

The feasibility of a newly synthesized Rh(III) complex, Rh[(trpy)(bpy)Cl](PF₆)₂, as a novel ionophore for the preparation of anion-selective polymeric membrane electrodes was tested. The ionophore exhibited anti-Hofmeister behavior with enhanced potentiometric selectivity toward thiocyanate ion compared to other anions. The influence of some experimental parameters such as membrane composition, nature and amount of plasticizer and additive and concentration of internal solution on the potential response of the SCN⁻ sensor were investigated. The electrode exhibits a Nernstian response for SCN⁻ over a wide concentration range (1.0 × 10⁻⁵ to 1.0 × 10⁻¹ M) with a slope −58.7 ± 0.5 mV per decade and a detection limit of 4.0 × 10⁻⁶ M (0.23 ppm). It could be used in a pH range of 3.0-8.0 and has a fast response time of about 15 s. The proposed sensor was used for the determination of thiocyanate ions in real samples such as urine and saliva of smokers and nonsmokers and, as an indicator electrode, in potentiometric titrations of SCN⁻ ion.     

Electrochemiluminescence from tris(2,2′-bipyridyl)ruthenium(II)-graphene-Nafion modified electrode

An electrochemiluminescence (ECL) sensor based on Ru(bpy)₃²⁺-graphene-Nafion composite film was developed. The graphene sheet was produced by chemical conversion of graphite, and was characterized by atomic force microscopy (AFM), scanning electron microscopy (SEM), and Raman spectroscopy. The introduction of conductive graphene into Nafion not only greatly facilitates the electron transfer of Ru(bpy)₃²⁺, but also dramatically improves the long-term stability of the sensor by inhibiting the migration of Ru(bpy)₃²⁺ into the electrochemically inactive hydrophobic region of Nafion. The ECL sensor gives a good linear range over 1 × 10⁻⁷ to 1 × 10⁻⁴ M with a detection limit of 50 nM towards the determination of tripropylamine (TPA), comparable to that obtained by Nafion-CNT. The ECL sensor keeps over 80% and 85% activity towards 0.1 mM TPA after being stored in air and in 0.1 M pH 7.5 phosphate buffer solution (PBS) for a month, respectively. The long-term stability of the modified electrode is better than electrodes modified with Nafion, Nafion-silica, Nafion-titania, or sol-gel films containing Ru(bpy)₃²⁺. Furthermore, the ECL sensor was successfully applied to the selective and sensitive determination of oxalate in urine samples.     

Immobilization of [Cu(bpy)2]Br2 complex onto a glassy carbon electrode modified with α-SiMo12O40 and single walled carbon nanotubes: Application to nanomolar detection of hydrogen peroxide and bromate

A simple procedure has been used for preparation of modified glassy carbon electrode with carbon nanotubes and copper complex. Copper complex [Cu(bpy)₂]Br₂ was immobilized onto glassy carbon (GC) electrode modified with silicomolybdate, α-SiMo₁₂O₄₀⁴⁻ and single walled carbon nanotubes (SWCNTs)_. Copper complex and silicomolybdate irreversibly and strongly adsorbed onto GC electrode modified with CNTs. Electrostatic interactions between polyoxometalates (POMs) anions and Cu-complex, cations mentioned as an effective method for fabrication of three-dimensional structures. The modified electrode shows three reversible redox couples for polyoxometalate and one redox couple for Cu-complex at wide range of pH values. The electrochemical behavior, stability and electron transfer kinetics of the adsorbed redox couples were investigated using cyclic voltammetry. Due to electrostatic interaction, copper complex immobilized onto GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ electrode shows more stable voltammetric response compared to GC/CNTs/Cu-complex modified electrode. In comparison to GC/CNTs/Cu-complex the GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ modified electrodes shows excellent electrocatalytic activity toward reduction H₂O₂ and BrO₃⁻ at more reduced overpotential. The catalytic rate constants for catalytic reduction hydrogen peroxide and bromate were 4.5(±0.2) × 10³ M⁻¹ s⁻¹ and 3.0(±0.10) × 10³ M⁻¹ s⁻¹, respectively. The hydrodynamic amperommetry technique at 0.08 V was used for detection of nanomolar concentration of hydrogen peroxide and bromate. Detection limit, sensitivity and linear concentration range proposed sensor for bromate and hydrogen peroxide detection were 1.1 nM and 6.7 nA nM⁻¹, 10 nM-20 μM, 1 nM, 5.5 nA nM⁻¹ and 10 nM-18 μM, respectively.     

A new electrochemiluminescent detection system equipped with an electrically controlled heating cylindrical microelectrode

A new electrochemiluminescent (ECL) detection system equipped with an electrically controlled heating cylindrical microelectrode (HME) was developed in this paper. The cylindrical microelectrode made of platinum wire (25 μm in diameter, 6 mm in long) was used as the working electrode of the ECL detection system, the temperature of the electrode could be controlled electrically. The Ru(bpy)₃²⁺-ECL and Ru(bpy)₃²⁺-C₂O₄²⁻-ECL systems were used to evaluate this ECL detection system. The detection limit for oxalate was found to be 3.0 × 10⁻⁴ mol/L when T_e (temperature of the HME) was 22 °C, and found to be 3.0 × 10⁻⁶ mol/L at 80 °C, which indicates that the detection limit can be improved greatly at higher T_e, based on which, it is possible to establish a more sensitive method for measurement of ECL by using a heated microelectrode.     

Prussian Blue electrodeposited on MWNTs-PANI hybrid composites for H2O2 detection

A Prussian Blue (PB)/polyaniline (PANI)/multi-walled carbon nanotubes (MWNTs) composite film was fabricated by step-by-step electrodeposition on glassy carbon electrode (GCE). The electrode prepared exhibits enhanced electrocatalytic behavior and good stability for detection of H₂O₂ at an applied potential of 0.0 V. The effects of MWNTs thickness, electrodeposition time of PANI and rotating rate on the current response of the composite modified electrode toward H₂O₂ were optimized to obtain the maximal sensitivity. A linear range from 8 × 10⁻⁹ to 5 × 10⁻⁶ M for H₂O₂ detection has been observed at the PB/PANI/MWNTs modified GCE with a correlation coefficient of 0.997. The detection limit is 5 × 10⁻⁹ M on signal-to-noise ratio of 3. To the best of our knowledge, this is the lowest detection limit for H₂O₂ detection. The electrode also shows high sensitivity (526.43 μA μM⁻¹ cm⁻²) for H₂O₂ detection which is more than three orders of magnitude higher than the reported.     

Synthesis of Cu-mediated nano-sized salbutamol-imprinted polymer and its use for indirect recognition of ultra-trace levels of salbutamol

Cu²⁺-mediated salbutamol-imprinted polymer nanoparticles, synthesized by precipitation polymerization, were mixed with graphite powder and n-eicosane in order to fabricate a modified carbon paste electrode. This electrode was then applied for indirect differential pulse voltammetry determination of salbutamol. In the presence of Cu²⁺ ions, the formed Cu²⁺–salbutamol complex was adsorbed in to the pre-designed cavities of the MIP particles, situated on the electrode surface. Since the electrochemical signal of salbutamol was intrinsically small, the oxidation peak of the participant Cu²⁺, after reduction step, was recorded and used as an indication of salbutamol amount, adsorbed in the electrode. Different variables influencing the sensor performance were studied and the best conditions were chosen for the determination purpose. Correlation between the sensor response to salbutamol and its concentration was linear in the range of 1.0 × 10⁻⁹–5.5 × 10⁻⁸ M. Detection limit was calculated equal to 6.0 × 10⁻¹⁰ M (S/N). Five replicated determination of salbutamol (1 × 10⁻⁸ M) resulted in standard error of 3.28%, meaning a satisfactory precision of the determination method. The prepared sensor was applied for real sample analysis. In order to minimize the interference effect, the synthesized polymer was successfully used as a solid phase sorbent for salbutamol extraction, before analysis of real samples by the developed sensor.     

Construction of a new Cu2+ coated wire ion selective electrode based on 2-((2-(2-(2-(2-hydroxy-5-methoxybenzylidene amino)phenyl)disufanyl)phenylimino)methyl)-4-methoxyphenol Schiff base

In this article a new coated platinum Cu²⁺ ion selective electrode based on 2-((2-(2-(2-(2-hydroxy-5-methoxybenzylideneamino)phenyl)disufanyl)phenylimino) methyl)-4-methoxyphenol Schiff base (L₁) as a new ionophore is described. This sensor has a wide linear range of concentration (1.2 × 10⁻⁷-1.0 × 10⁻¹ mol L⁻¹) and a low detection limit of 9.8 × 10⁻⁸ mol L⁻¹of Cu(NO₃)₂. It has a Nernstian response with slope of 29.54 ± 1.62 mV decade⁻¹ and it is applicable in the pH range of 4.0-6.0 without any divergence in potentioal. The coated electrode has a short response time of approximately 9 s and is stable at least for 3.5 months. The electrode shows a good selectivity for Cu²⁺ ion toward a wide variety of metal ions. The proposed sensor was successfully applied for the determination of Cu²⁺ ion in different real and environmental samples and as indicator electrode for potentiometric titration of Cu²⁺ ion with EDTA.     

3D nanostructured Ni(OH)2 microspheres as an efficient immobilization matrix of Ru(bpy)3 for high-performance electrochemiluminescence sensor

The electrochemistry and electrochemiluminescence (ECL) of novel three-dimensional nanostructured Ru(bpy)₃²⁺/Ni(OH)₂ microspheres were investigated for the first time. The negatively charged porous Ni(OH)₂ microspheres composed of Ni(OH)₂ nanowires were specifically designed to interact with Ru(bpy)₃²⁺. The large surface area and porous structure of Ni(OH)₂ microspheres enhance loading of Ru(bpy)₃²⁺ and mass transport of the model analyte, tripropylamine (TPA). Excellent ECL performance of the presented sensor was achieved including good stability and wide linear range from 7.7 × 10⁻¹⁰ to 3.8 × 10⁻³ M with the detection limit of 2.6 × 10⁻¹⁰ M to TPA.     

Highly selective and sensitive thiocyanate membrane electrode based on nickel(II)-1,4,8,11,15,18,22,25-octabutoxyphthalocyanine

A highly selective membrane electrode based on nickel(II)-1,4,8,11,15,18,22,25-octabutoxyphthalocyanine (NOBP) is presented. The proposed electrode shows very good selectivity for thiocyanate ions over a wide variety of common inorganic and organic anions. The sensor displays a near Nernstian slope of −58.7 ± 0.6 mV per decade. The working concentration range of the electrode is 1.0 × 10⁻⁶ to −1.0 × 10⁻¹ M with a detection limit of 5.7 × 10⁻⁷ M (33.06 ng/mL). The response time of the sensor in whole concentration ranges is very short (<10 s). The response of the sensor is independent on the pH range of 4.3-9.8. The best performance was obtained with a membrane composition of 30% PVC, 65% dibutyl phthalate, 3% NOBP and 2% hexadecyltrimethylammonium bromide. It was successfully applied to direct determination of thiocyanate in biological samples, and as an indicator electrode for titration of thiocyanate ions with AgNO₃ solution.     

Determination of itopride hydrochloride by high-performance liquid chromatography with Ru(bpy)3 electrogenerated chemiluminescence detection

In this work, a stable electrogenerated chemiluminescence (ECL) detector was developed. The detector was prepared by packing cation-exchanged resin particles in a glass tube, followed by inserting Pt wires (working electrode) in this tube and sealing. The leakage of Ru(bpy)₃²⁺ can be compensated by adding a small amount of Ru(bpy)₃²⁺ into solution phase. Coupled with high-performance liquid chromatography separation, the detector has been used for determination of itopride hydrochloride in human serum. Under the optimal conditions, the ECL intensity has a linear relationship with the concentration of itopride hydrochloride in the range of 1.0 × 10⁻⁸ g mL⁻¹ to 1.0 × 10⁻⁶ g mL⁻¹ and the detection limit was 3 × 10⁻⁹ g mL⁻¹ (S/N = 3). The as-prepared ECL detector displayed good sensitivity and stability.     

A novel cobalt(II)-selective potentiometric sensor based on p-(4-n-butylphenylazo)calix[4]arene

A new poly(vinyl chloride)-based membranes containing p-(4-n-butylphenylazo)calix[4]arene (I) as an electroactive material along with sodiumtetraphenylborate (NaTPB), and dibutyl(butyl)phosphonate in the ratio 10:100:1:200 (I:DBBP:NaTPB:PVC) (w/w) was used to fabricate a new cobalt(II)-selective sensor. It exhibited a working concentration range of 9.2 × 10⁻⁶ to 1.0 × 10⁻¹ M, with a Nernstian slope of 29.0 ± 1.0 mV/decade of activity and the response time of 25 s. This sensor shows the detection limit of 4.0 × 10⁻⁶ M. Its potential response remains unaffected of pH in the range, 4.0-7.2, and the cell assembly can be used successfully in partially non-aqueous medium (up to 10%, v/v) without significant change in the slope of working concentration range. The sensor has a lifetime of about 3 months and exhibits excellent selectivity over a number of mono-, bi-, and tri-valent cations including alkali, alkaline earth metal, heavy and transition metal ions. It can be used as an indicator electrode for the end point determination in the potentiometric titration of cobalt ions against ethylenediaminetetraacetic acid (EDTA) as well as for the determination of cobalt ion concentration in real samples.     

Application of manganese (II) phthalocyanine synthesized in situ in the SiO2/SnO2 mixed oxide matrix for determination of dissolved oxygen by electrochemical techniques

This work describes the in situ immobilization of Mn(II) phthalocyanine (MnPc) in a porous SiO₂/SnO₂ mixed oxide matrix obtained by the sol gel processing method. The chemically modified matrix SiO₂/SnO₂/MnPc, possessing an estimated amount of 8 × 10⁻¹⁰ mol cm⁻² of MnPc on the surface, was used to prepare an electrode to analyze dissolved oxygen in water by an electrochemical technique. The electrode was prepared by mixing the material with ultrapure graphite and evaluated using differential pulse voltammetry. Dissolved O₂ was reduced at −0.31 V with a limit of detection (LOD) equal to 7.0 × 10⁻⁴ mmol L⁻¹. A mechanism involving four electrons in O₂ reduction was determined by the rotating disk electrode technique.     

A chloride selective sensor based on a calix[4]arene possessing a urea moiety

New calix[4]arene derivative 1 of 1,3-alternate conformation with a ureido moiety has been synthesized in high yield and examined for its anion recognition abilities towards anions such as fluoride, chloride, bromide, iodide, nitrate and acetate by ¹H NMR and UV-vis spectroscopy. The results show that receptor has strong binding affinity for chloride ions. A chloride ion selective electrode (ISE) was also formed which showed excellent selectivity over all the other anions tested. The limit of detection is 2.51 × 10⁻⁵ mol dm⁻³.     

Novel potentiometric membrane sensor based on 6-(4-nitrophenyl)-2-phenyl-4,4-dipropyl-3,5-diaza-bicyclo[3,1,0] hex-2-ene for detection of strontium (II) ions at trace levels

A new PVC membrane strontium ion-selective electrode has been constructed using 6-(4-nitrophenyl)-2-phenyl-4,4-dipropyl-3,5-diaza-bicyclo[3,1,0] hex-2-ene (NPDBH) as a neutral ionophore. The electrode was prepared with 7% NPDBH (as ionophore), 57% acetophenone (as plasticizer), 30% PVC and 6% oleic acid (as lipophilic additive). The electrode responds to Sr²⁺ ion with a sensitivity of 28.2 ± 0.5 mV/decade over the range 1.0 × 10⁻⁶-1.0 × 10⁻¹ mol L⁻¹ and in a pH range of 3.0-10.0. The limit of detection was 2.4 × 10⁻⁷ mol L⁻¹. It has a response time of <20 s and can be used for at least three months without any divergence in potentials. The proposed electrode shows good discrimination of Sr²⁺ ion from several cations. The effect of organic solvents on electrode response was examined. The results show that this electrode can be used in ethanol media up to 15% (v/v) concentration without interference. The isothermal temperature coefficient of this electrode amounted to 0.00019 V/°C. The electrode was found to work well under laboratory conditions. It was successfully applied to the determination of strontium ions in human urine and bone digests.     

Electrochemical behaviour of epinephrine and uric acid at a Sonogel-Carbon l-Cysteine modified electrode

The Sonogel-Carbon electrode is a special class of sol-gel electrode that exhibits favourable mechanic and electric properties to be used as electrochemical sensor. In this study, Sonogel-Carbon modified with l-Cysteine was used to prepare a novel electrochemical sensor. The objective of this novel electrode modification was to seek new electrochemical performances for detection of epinephrine in the presence of uric acid. The response of catalytic current with epinephrine concentration shows a linear relation in the range from 1 × 10⁻⁷ to 5 × 10⁻⁴ M with a correlation coefficient of 0.998, and a detection limit of 8.7 × 10⁻⁸ M. The modified electrode had also been applied to the determination of epinephrine and uric acid in biological samples with satisfactory results. A surface characterisation of this modified electrode was carried out helped by scanning electron microscopy (SEM) and X-Ray energy dispersive spectroscopy (EDS).     

A novel nonenzymatic sensor based on LaNi0.6Co0.4O3 modified electrode for hydrogen peroxide and glucose

In this paper, LaNi_0.6Co_0.4O₃ (LNC) nanoparticles were synthesized by the sol–gel method, and the structure and morphology of LNC nanoparticles were characterized by X-ray diffraction spectrum, scanning electron microscopy and transmitting electron microscopy. And then, LNC was used to modify carbon paste electrode (CPE) without any adhesive to fabricate hydrogen peroxide and glucose sensor, and the results demonstrated that LNC exhibited strong electrocatalytical activity by cyclic voltammetry and amperometry. In H₂O₂ determination, linear response was obtained in the concentration range of 10 nM–100 μM with a detection limit of 1.0 nM. In glucose determination, there was the linear region of 0.05–200 μM with a detection limit of 8.0 nM. Compared with other reports, the proposed sensor also displayed high sensitivity toward H₂O₂ (1812.84 μA mM⁻¹ cm⁻²) and glucose (643.0 μA mM⁻¹ cm⁻²). Moreover, this prepared sensor was applied to detect glucose in blood serum and hydrogen peroxide in toothpaste samples with satisfied results, indicating its possibility in practical application.     

Improved potentiometric response of solid-contact lanthanum (III) selective electrode

For the first time, the analytical application of integrate ionophore-transducer material based on magnetic graphene hybrids and 2,2-dithiodipyridine (DTDP) in solid-contact lanthanum (III) selective electrode is reported. The attachment of Fe₃O₄ nanoparticles (NPs) to graphene oxide (GO) for magnetic graphene hybrid is achieved by covalent bonding, and the universal problem, Fe₃O₄ NPs may easily leach out from the graphene during application, is successfully solved by the method above. The proposed electrode exhibits an excellent near-Nernstian response to lanthanum (III) ranging from 1.0 × 10⁻⁹ to 1.0 × 10⁻³ M with a slope of 17.81 mV/dec. Moreover, the excellent performance on fairly good selectivity, wide applicable pH range (3.0^_8.0), fast response time (10 s) and long life time (2 months) reveal the superiority of the electrode. Most importantly, we have made a great improvement in the detection limit (2.75 × 10⁻¹⁰ M), which brings new dawn to the real-time detection of lanthanum (III) using ion selective electrode.     

A novel colorimetric and fluorescent chemosensor: synthesis and selective detection for Cu and Hg

A novel two-channel metal ion sensor has been synthesized from macrocyclic dioxotetraamine and 1,8-naphthalimide derivative. The metal ion-selective signaling behaviors of the sensor were investigated. The sensor presented the selective coloration for Cu²⁺ and Hg²⁺ that can be detected by the naked-eye, respectively. Besides, the addition of Cu²⁺ and Hg²⁺ quenched the fluorescence of 1 obviously and the detection limit was found to be 3 × 10⁻⁷ M for Cu²⁺ and 7 × 10⁻⁷ M for Hg²⁺. This sensor can be utilized for the visual and spectroscopic detection of Cu²⁺ or Hg²⁺ in the presence of the other competing metal ions.