银基带再结晶织构的EBSD分析

本文采用EBSD(电子背散射衍射)等分析手段对{110}<110>取向的银基带的织构形成机理进行了深入研究,发现了冷轧织构与不同退火温度下再结晶织构间的取向转变关系,研究发现,{110}面附近且非{110}<211>取向的冷轧织构组分,900℃退火可以转变为强的{110}<110>织构.织构转变中有孪晶形成,{110}<110>和{110}<114>取向互为孪晶关系.     

CVD金刚石薄膜孪晶形成的原子机理分析

采用X射线衍射技术、电子背散射衍射技术和扫描电镜分别观察了不同甲烷浓度条件下沉积的CVD自支撑金刚石薄膜的宏观织构、晶界分布和表面形貌. 研究了一阶孪晶在金刚石晶体{111}面生长的原子堆垛过程. 结果表明，由于一阶孪晶〈111〉60°的取向差关系以及{111}面的原子堆垛结构，使{111}面上容易借助碳原子的偏转沉积产生一阶孪晶. 低甲烷浓度时，碳原子倾向于在表面能较低的{111}面沉积，为孪晶的形成提供了便利，且高频率孪晶使薄膜织构强度减弱. 甲烷浓度升高使生长激活能较小的{001}面成为主要前沿生长面，因而只有〈001〉晶向平行薄膜法向的晶粒能够不断长大，因此孪晶形核概率明显减小. 另外，在薄膜中发现二阶孪晶，并对二阶孪晶的形成进行了分析. 关键词： 金刚石薄膜 孪晶 原子机理 取向差     

改善YBCO高温超导银基带的织构

采用部分再结晶的方法对形成{110}<110>多晶Ag织构的"领先再结晶取向"进行了研究.通过控制银的纯度及冷轧和再结晶退火过程,得到了很强{110}<110> 织构的银基带,并对织构形成过程进行了探索.     

在Ag基带上用PLD法沉积YBCO超导薄膜的研究

Ag是目前唯一不需要隔离层的高温超导基带材料，而且研究表明，在YBCO中掺入适量的Ag，将有利于超导性能的改善和表面电阻的降低．本研究采用准分子激光法（PLD），在经不同表面处理的{110}〈110〉取向的双轴织构银基带上直接沉积了YBCO薄膜，得到了强双轴织构的超导膜，系统地研究了银基带中的孪晶、晶界等缺陷对YBCO超导微观组织的影响．     

γ-TiAl金属间化合物面缺陷能的分子动力学研究

运用分子动力学方法，对γ-TiAl金属间化合物的面缺陷能(层错能和孪晶能)进行了研究. 计算得到γ-TiAl不同滑移系(或孪生系)的整体堆垛层错能曲线，结果表明，γ-TiAl较一般fcc晶体结构的金属可动滑移系(孪生系)的数量减少，在外界条件下呈脆性. 研究孪生系(1/6)〈112〉{111}的弛豫的整体堆垛层错(GSF)能和整体孪晶(GTF)能曲线，对不稳定层错能γ_usf、稳定层错能γ_sf和不稳定孪晶能γ_usf值进行分析，可以预知， γ-TiAl的主要变形机理为孪生系(1/6)〈112〉{111}的孪生和普通滑移系(1/6)〈110〉{111}的滑移，以及超滑移系(1/2)〈011〉{111}的滑移. 关键词： γ-TiAl')" href="#">γ-TiAl 堆垛层错能 孪晶能 分子动力学     

在Ag基带上用PLD法沉积YBCO超导薄膜的研究

Ag是目前唯一不需要隔离层的高温超导基带材料,而且研究表明,在YBCO中掺入适量的Ag,将有利于超导性能的改善和表面电阻的降低.本研究采用准分子激光法(PLD),在经不同表面处理的{110}<110>取向的双轴织构银基带上直接沉积了YBCO薄膜,得到了强双轴织构的超导膜,系统地研究了银基带中的孪晶、晶界等缺陷对YBCO超导微观组织的影响.     

Ni_3(Ti_x,V_(1-x))合金系中的长周期结构

本文利用电子衍射及高分辨点阵象实验方法证实了Ni_3(Ti_x,V_(1-x))合金系在铸态下存在有9R,10H,16H,20H,21H,44H等长周期结构以及2H结构。它们与体心四方基体相(结构与Ni_3V相同)及六角基体相(结构与Ni_3Ti相同)有固定取向关系:{001}_(长周期)∥{001}_(Ni_3Ti)∥{112}_(Ni_3V);〈100〉_(长周期)∥〈100〉_(Ni_3Ti)∥〈110〉_(Ni_3V_-)。样品经长期高温退火处理后其它长周期结构均向9R结构转变。     

bcc Fe中刃型位错的结构及能量学研究

基于位错理论，利用分子动力学方法建立了〈100〉{010}，〈100〉{011}，1/2〈111〉{011}和1/2〈111〉{112}刃型位错的芯结构，并计算了这四种刃型位错的形成能、位错芯能量和芯半径.计算结果表明：〈100〉{010}和〈100〉{011}刃型位错的形成能比1/2〈111〉{011}和1/2〈111〉{112}刃型位错的要高，这表明〈100〉刃型位错比1/2〈111〉刃型位错更难形成.而〈100〉{010}和〈100〉{011}刃型位错的芯半径比1/2〈111〉{011}和1/2〈111〉{112}刃型位错的小，这说明在1/2〈111〉刃型位错中位于奇异区的原子数多于〈100〉刃型位错，而这些原子要比完整晶体中的原子具有更大的活性.可见，1/2〈111〉刃型位错比〈100〉刃型位错更易运动，且〈100〉刃型位错在bcc Fe中难以形成. 关键词： bcc Fe 刃型位错 分子动力学模拟     

镍单晶膜上氧化镍的配位生长取向关系

对在膜面为(110),(001)和(111)的镍单晶膜上生成的氧化镍取向进行了电子衍射分析,除在(111)和(001)镍膜上肯定了前人已发现的氧化镍与镍的平行取向关系外,还在(110)和(001)镍单晶膜上发现了(111)_NiO∥(001)_Ni,〈110〉_NiO∥〈110〉_Ni取向关系以及〈110〉_NiO∥〈110〉_Ni氧化镍纤维织构。在所有氧化镍与镍的取向关系中均有〈110     

NiTi记忆合金中R相和马氏体相中孪晶界面的群论分析

利用母相群对低温相群陪集分解的理论,确定了NiTi形状记忆合金中R相存在四种变体,变体之间以{110}_p和{100}_p作为孪晶界面,四种变体可构成三种自适应群。马氏体相中存在三种变体,变体间的孪晶界面为{110}_p,三种变体可以构成四种呈三角形分布的自适应群。所得结果与实验工作基本一致。 关键词：     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.     

Direction-of-arrival estimation using matrix spatial prefiltering approach

An approach to direction-of-arrival （DOA） estimation for multiple narrowband farfield signals is proposed. The technique uses a novel matrix spatial prefiltering approach. Specifically, a matrix filter is designed to spatially filter the incoming data snapshots. The un-wanted components arriving from the stopband angular sectors are attenuated and the desired components from the angular sector of interest pass with minimal distortion. The matrix filter spatially filters the element-space data and the output reserves the element-space data property, which makes it very useful by passing sensor data through a spatial prefilter prior to applying many other array processors to attenuate interferences and improve system performance. Several examples of DOA estimation problem are presented to illustrate the performance of the proposed spatial prefiltering approach. Results of simulation and real data show that the pre-filter can efficiently attenuate the spatial interferences and significantly improve the estimation and resolution capability of DOA estimators at low signal-to-noise ratios for the sources located inside the passband sector. In addition, the use of spatial prefilter makes it possible to estimate DOAs for multiple sources more than the number of the elements of an array.     

Quantum efficiency calibration of opto-electronic detector by means of correlated photons method

A new calibration method of detectors can be realized by using correlated photons generated in spontaneous parametric down-conversion (SPDC) effect of nonlinear crystal.An absolute calibration system of detector quantum efficiency is performed.And its principle and experimental setup are introduced.A continuouswave (CW) ultraviolet (351 nm),diode-pumped,frequency-doubled,and solid-state laser is used to pump BBO crystal.The quantum efficiencies of the photomultiplier at 633,702,and 789 nm are measured respectively.The coincidence peaks are observed using coincidence circuit.Some measurement factors including the filter bandwidth of trigger channel,the detector position alignment and polarization of the pump light are analyzed.The uncertainties of this calibration method are also analyzed,and the relative uncertainties of total calibration are less than 5.8%.The accuracy of this method could be improved in the future.