基于HRTEM和Raman分析定向多壁碳纳米管阵列的生长机理

以二茂铁、二甲苯为前驱体,石英为衬底,在850 oC的管式炉内采用化学气相沉积法制备出了定向碳纳米管阵列. 高分辨透射电子显微镜和拉曼光谱的结果表明：碳纳米管阵列具有良好的定向性和多壁管状结构,石墨化程度高,并且只在表面存在少量单壁碳纳米管.定向多壁碳纳米管阵列的生长模式为“底部”生长模式,即在生长的初期,当催化剂颗粒较小时,析出的碳原子生成了单壁碳纳米管或与其性质类似的多壁碳纳米管(一般层数小于5层);催化剂颗粒逐渐长大后,大量的碳原子析出后生成了普通的多壁碳纳米管,从而形成了单壁碳纳米管只存在于碳纳米管阵列膜表面和多层碳纳米管膜表面与界面的现象.     

碳纳米管在银基底上的表面增强拉曼散射光谱研究(英文)

介绍了一种单壁碳纳米管表面增强拉曼散射的新方法。依据碳纳米管独特的力学性能,在银表面直接研磨单壁碳纳米管,在形成纳米级粗糙银表面的同时,单壁碳纳米管也吸附在银表面上。在银表面粗糙程度和单壁碳纳米管厚度适中的区域得到了高质量的单壁碳纳米管SERS谱。该方法消除了溶剂的干扰,保证了结果的准确性,理论分析和实验结果表明该方法是正确的、可行的     

单壁碳纳米管膜及其三聚氰胺甲醛树脂复合材料的光电特性

单壁碳纳米管能够强烈吸收光线,尤其是在近红外区域,并能将光能转换成热能.同时,单壁碳纳米管还具有相当大的将热能转换成电能的能力.通过真空过滤方法,将由化学气相沉积生成的单壁碳纳米管阵列制备成单壁碳纳米管膜.根据研究的需要设计了一个简单的单壁碳纳米管膜光伏性质测试实验装置,并在其两端成功地实现了由红外光转换为电压输出.通过功能化步骤,制备了单壁碳纳米管/三聚氰胺甲醛树脂复合材料膜,实验结果表明该复合材料能产生符号相反的输出电压.这预示着单壁碳纳米管及其三聚氰胺甲醛树脂复合材料在光电领域具有良好的应用前景.     

以Y/Ni为催化剂制备的单壁碳纳米管的拉曼光谱研究

采用电弧放电法以Y/Ni为催化制备了单壁碳纳米管（SWNTs），对样品进行了扫描电镜、透射电镜和拉曼光谱的研究。所制备的样品中单壁碳纳米管的含量较高。对单壁碳纳米管的共振拉曼散射增强效应进行了观察，随激光波长的不同，单壁碳纳米管的拉曼光谱也随之变化，尤其是低频区径向呼吸模的变化比较明显。利用布里渊区折叠法计算了单壁碳纳米管的电子态密度曲线，根据SWNTs电子态密度尖峰之间的能量差、管子的直径和呼吸模频率建立了一个图表，并对SWNTs的呼吸模进行了归属。分析结果表明：样品中单壁碳纳米管的直径分布在0.79-1.76nm范围，金属管和半导体管均存在，并且直径在1.45nm附近的碳管居多。     

单壁碳纳米管-聚合物复合材料的拉曼光谱表征(英文)

本文在粗糙金属表面上制作了单壁碳纳米管—聚乙烯醇复合材料,并利用表面增强拉曼散射讨论了碳纳米管与聚乙烯醇之间的相互作用     

单壁碳纳米管声子谱及比热计算

利用卷曲法计算了有限长单壁碳纳米管的声子色散关系．讨论了单壁碳纳米管的比热随管径、温度的变化趋势．结果表明碳管的比热随温度、管径的增大而增大,并逐渐趋于一恒定数值．根据色散关系的计算结果,给出了有限长（5,5）型单壁碳纳米管的振动模式以及部分振动模式的频率随长度的变化关系． 关键词： 碳纳米管 声子 比热     

半导体性单壁碳纳米管与其石墨衬底表面相互作用的第一性原理计算

利用基于密度泛函理论的计算方法,研究了处于石墨（HOPG）表面的半导体性单壁碳纳米管,发现碳纳米管下面的石墨受碳管的作用向下凹陷,而纳米管本身虽然保持其形状不变,但它的电子态受石墨衬底影响,造成导带下移,禁带宽度明显减小. 关键词： 单壁碳纳米管 密度泛函理论 局域密度近似方法     

嵌入锂原子的zigzag型单壁碳纳米管的电子传导特性

运用基于第一性原理的密度泛函理论（DFT）的非平衡格林函数（NEGF）方法对Li原子嵌入后的zigzag型单壁碳纳米管(SWCNT)的电子输运性质进行了研究.在构建和优化了Li原子嵌入的zigzag型单壁碳纳米管的电子输运模型后,研究了该系统的电子传输概率、能态密度、电子透射谱,还研究了电子能量和偏置电压设置与变化对其电子输运特性的影响.结果显示zigzag型单壁碳纳米管嵌入Li原子后,电子输运特性发生了较大变化,具有电子输运拓宽效应和量子台阶复苏效应. 关键词： Li原子 碳纳米管 电子输运 拓宽效应     

电子束诱导单壁碳纳米管不稳定的新观察

利用透射电镜在室温下对不同形态的单壁碳纳米管进行了原位电子束辐照研究.研究发现:在相同的辐照条件下随着辐照时间(或辐照剂量)的增加,两端固定的单壁碳纳米管径向收缩,且收缩速率越来越快;相同直径的轴向弯曲的单壁碳纳米管比平直的单壁碳纳米管更加不稳定;一端固定另端自由的单壁碳纳米管轴向收缩,但其直径基本不变.利用单壁碳纳米管纳米曲率效应和能量束诱导非热激活效应,对上述单壁碳纳米管不稳定性现象进行了新的、合理的解释.     

Rh在单壁碳纳米管上吸附的密度泛函理论研究

本文利用密度泛函理论研究了Rh原子在（6,6）单壁碳纳米管内外的吸附行为. 通过对Rh在单壁碳纳米管上不同吸附位的吸附构型与吸附能的研究发现: Rh吸附在管内、外的洞位最稳定, 且管外吸附比在管内强. 这是由于单壁碳纳米管的卷曲效应使得管外电荷密度比管内大造成的. 态密度分析表明, 吸附在管内外的Rh原子的5s电子均转移到了4d轨道上; Rh原子4d轨道上的电子转移到了（6, 6）碳管上, 使Rh带正电, 碳管带负电. 结合能带分析表明, Rh原子吸附在管内磁性较弱, 而吸附在管外较强. 关键词： 密度泛函理论 单壁碳纳米管 Rh原子 吸附     

Adsorption of nonpolar benzene derivatives on single-walled carbon nanotubes

The adsorption of benzene, toluene, and chlorobenzene on single-walled carbon nanotubes (SWCNTs) with and without acid oxidation was conducted to investigate the influences of derivative groups on benzene rings and functional groups from SWCNTs on adsorption by SWCNTs. The SWCNTs of high purity were chosen and moderate acid oxidation was performed so that the surface physical properties remained unchanged after acid oxidation and the influences of acid oxidation on adsorption were only contributed from the modification of the surface chemistry of SWCNTs. The oxygen-containing surface groups introduced by acid oxidation obstructed the interactions between functional groups of nonpolar benzene derivatives and C-rings of SWCNTs significantly. The dispersive interaction between the partially positive H⁺ of the methyl group and the oxygen-containing surface groups slightly increased the adsorption of toluene on oxidized SWCNTs at high solution pH. The thermodynamic of adsorption was also studied at different temperatures.     

Functionalization of vertically aligned carbon nanotubes with polystyrene via surface initiated reversible addition fragmentation chain transfer polymerization

Here we demonstrate the covalent attachment of vertically aligned (VA) acid treated single-walled carbon nanotubes (SWCNTs) onto a silicon substrate via dicyclohexylcarbodiimide (DCC) coupling chemistry. Subsequently, the pendant carboxyl moieties on the sidewalls of the VA-SWCNTs were derivatized to acyl chlorides, and then finally to bis(dithioester) moieties using a magnesium chloride dithiobenzoate salt. The bis(dithioester) moieties were then successfully shown to act as a chain transfer agent (CTA) in the reversible addition fragmentation chain transfer (RAFT) polymerization of styrene in a surface initiated “grafting-from” process from the VA-SWCNT surface. Atomic force microscopy (AFM) verified vertical alignment of the SWCNTs and the maintenance thereof throughout the synthesis process. Finally, Raman scattering spectroscopy and AFM confirmed polystyrene functionalization.     

单壁BN纳米管和碳纳米管物理吸附储氢性能的理论对比研究

采用巨正则蒙特卡罗方法(GCMC)研究了单壁氮化硼纳米管(SWBNNTs)和单壁碳纳米管(SWCNTs)的物理吸附储氢性能,主要对比研究了纳米管的管径、温度和手性对二者物理吸附储氢量的影响. 研究结果表明：在低温下,SWBNNTs的物理吸附储氢性能优于相应的SWCNTs;但是随着温度的升高,二者的物理吸附储氢性能差别越来越小,在常温下,SWBNNTs不具备有比SWCNTs更强的物理吸附储氢性能,而是和相同条件下的SWCNTs相差不大,只是在高压下的物理吸附储氢量稍稍大于SWCNTs,并给出了合理的理论解释 关键词： 巨正则蒙特卡罗方法(GCMC) 单壁氮化硼纳米管(SWBNNTs) 单壁碳纳米管(SWCNTs) 储氢     

Mechanical properties of nickel-coated single-walled carbon nanotubes and their embedded gold matrix composites

The effects of nickel coating on the mechanical behaviors of armchair single-walled carbon nanotubes (SWCNTs) and their embedded gold matrix composites under axial tension are investigated using molecular dynamics (MD) simulation method. The results show that the Young's moduli and tensile strength of SWCNTs obviously decrease after nickel coating. For armchair SWCNTs, the decreased ratio of the Young's moduli of SWCNTs with smaller radius is larger than that of SWCNTs with larger radius. A comparison is made between the response to Young's modulus of a composite with parallel embedded nanotube and the response of a composite with vertically embedded nanotube. The results show that the uncoated SWCNT can enhance the Young's modulus of composite under the condition of parallel embedment, but such improvement disappears under the condition of vertical embedment because the interaction between SWCNT and gold matrix is too weak for effective load transfer. However, the nickel-coated SWCNT can indeed significantly improve the composite behavior.     

Growth of single wall carbon nanotubes using PECVD technique: An efficient chemiresistor gas sensor

In this work, the uniform and vertically aligned single wall carbon nanotubes (SWCNTs) have been grown on Iron (Fe) deposited Silicon (Si) substrate by plasma enhanced chemical vapor deposition (PECVD) technique at very low temperature of 550 °C. The as-grown samples of SWCNTS were characterized by field emission scanning electron microscope (FESEM), high resolution transmission electron microscope (HRTEM) and Raman spectrometer. SWCNT based chemiresistor gas sensing device was fabricated by making the proper gold contacts on the as-grown SWCNTs. The electrical conductance and sensor response of grown SWCNTs have been investigated. The fabricated SWCNT sensor was exposed to ammonia (NH₃) gas at 200 ppm in a self assembled apparatus. The sensor response was measured at room temperature which was discussed in terms of adsorption of NH₃ gas molecules on the surface of SWCNTs. The achieved results are used to develope a miniaturized gas sensor device for monitoring and control of environment pollutants.     

一种高效的用含水乙醇制备单壁碳纳米管的方法

本文采用流化床反应器,利用MgO作为催化剂载体,以Mo和Fe为催化剂。让Ar气流携带含水的乙醇蒸汽进入反应器,通过化学气相沉积(CCVD)法合成了单壁碳纳米管(SWCNTs)。利用拉曼光谱和透射电镜(TEM)对所合成的单壁碳纳米管质量进行检测。实验结果表明无水乙醇中加入7%的水反应温度在950℃时,制备的单壁碳纳米管的质量最好而且管径分布非常均匀。     

Poly(Butylene Terephthalate)/Single Wall Carbon Nanotubes Composite Nanofibers by Electrospinning

Poly(buthylene terephthalate)(PBT)/single wall carbon nanotubes (SWCNTs) composite nanofibers were prepared by electrospinning. The effect of carbon nanotubes on the morphology, crystallization, and mechanical properties of the electrospun composite nanofibers were investigated by SEM, DSC, and tensile testing, respectively. SEM observations indicated that the presence of SWCNTs resulted in finer nanofibers for lower loading; however, a broader distribution, especially for the higher diameter ranges was found for nanofibers with higher amounts of carbon nanotubes. SWCNTs accelerated crystallization and acted as a nucleating agent; the degree of crystallinity increased with increasing content of SWCNTs, followed by a moderate decrease at higher content. Specific tensile strength and modulus of the PBT/SWCNTs composite nanofibers mats were higher than that of neat PBT nanofibers mat. However, the elongation at break of composite nanofibers mats was lower than that of the neat PBT nanofibers mat.     

金电极上Cu,Zn-SOD的表面增强拉曼光谱

应用原位共焦拉曼光谱技术在经表面增强处理后的金电极上,观察Cu,Zn-SOD分子的吸附方式及其随电位变化的过程。实验结果表明,在400mV-700mV的电位区间内,Cu,Zn-SOD分子始终以氨基酸残基上COO-和NH2在电极表面吸附,使活性中心所处的平面远离电极表面,且随电位负移发生脱附。上述结果为解释SOD分子在金电极表面无法实现快速电子传递提供了直接依据。     

Synthesis, characterization and mechanism of cetyltrimethylammonium bromide bilayer-encapsulated gold nanosheets and nanocrystals

Single-crystal Au nanosheets and fcc gold nanocrystals of uniform size were synthesized by a novel and simple route. The results of field-emission scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD) indicated the formation of the single-crystal structure of gold nanosheets and fcc nanocrystals. Energy-dispersive analysis of X-ray (EDAX) showed absorbance of cetyltrimethylammonium bromide (CTAB) molecules onto the surface of gold nanostructures. Moreover, zeta potential measurements showed that CTAB-coated nanostructures were positively charged and the zeta potential remained almost the same upon centrifugation and redispersion of the resulting nanostructures in methanol, confirming the high stability of the surfactant-protected nanocomposites. Evolution of the nanostructures during the reaction was monitored by TEM observations. The results indicated that the formation of the gold nanostructures followed a two-step mechanism with a bilayer CTAB structure on the surface of the gold nanostructures.     

Investigation of the surface properties of gold nanowire arrays

Gold nanowire arrays with diameters ranging from 45 to 200 nm were obtained via electrochemical deposition within the ion-track templates. The morphology of gold nanowires was imaged by scanning electron microscopy (SEM). The surface properties were investigated by surface plasmon resonance (SPR) and X-ray photoelectron spectroscopy (XPS). The SPR peaks were observed as the gold nanowire arrays embedded in the templates and their intensity decreased after the sample exposed to the air for a certain time due to the formation of chemisorbed oxygen on nanowire surface. The positive binding energy shifts in Au core level was found when the gold nanowire arrays embodied in template and the initial- and finial-state effects were introduced to explain this phenomenon.