Extraordinary transport behavior of gases in isothermally annealed poly(4‐methyl‐1‐pentene) membranes

Poly(4‐methyl‐1‐pentene) (PMP) membranes were modified through isothermal annealing to investigate the change of their crystalline structure and rigid and mobile amorphous fractions (RAF and MAF), assuming a three‐phase model, affected the gas transport behavior. The crystalline structure was characterized by wide‐angle X‐ray diffraction (WAXD) and small‐angle X‐ray scattering (SAXS) techniques, and the free volume properties were analyzed by positron annihilation lifetime spectroscopy. Compared with the pristine membrane, the annealed membranes show higher crystallinity; the crystals undergo partial structural change from form III to form I. The lamellar crystal thickness, rigid amorphous fraction thickness, and long period in the lamellar stacks increase with crystallinity. The annealed PMP membranes exhibit higher permeability due to the increase in larger size free volumes in MAF and higher selectivity due to the increase in smaller size free volumes in RAF, respectively. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2368–2376     

Preparation and enhanced properties of poly(propylene)/ silica‐grafted‐hyperbranched polyester nanocomposites

A series of poly(propylene) silica‐grafted‐hyperbranched polyester nanocomposites by grafting the modified hyperbranched polyester (Boltorn? H20), possessing theoretically 50% end carboxylic groups and 50% end hydroxyl groups, which endcapped with octadecyl isocyanate (C19), onto the surface of SiO₂ particles (30 nm) through 3‐glycidoxy‐propyltrimethoxysilane (GPTS) was prepared. The effect of silica‐grafted‐modified Boltorn? H20 on the mechanical properties of polypropylene (PP) was investigated by tensile and impact tests. The morphological structure of impact fracture surface and thermal behavior of the composites were determined by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC), respectively. The melt viscosity of composites was investigated by melt flow index (MFI). The obtained results showed that: (1) the modified Boltorn? H20 was successfully grafted onto the SiO₂ surface confirmed by FT‐IR and X‐ray photoelectron spectroscopy (XPS) analysis; (2) the incorporation of silica‐grafted‐modified Boltorn? H20 (3–5 wt% SiO₂) greatly enhanced the notched impact strength as well the tensile strength of the composites; (3) the incorporation of silica‐grafted‐modified Boltorn? H20 had no influence on the melting temperature and crystallinity of PP phase; (4) the MFI of PP composites increased when the silica‐grafted‐modified Boltorn? H20 particles were added compared with PP/SiO₂ or PP/SiO₂‐GPTS composites. Copyright © 2004 John Wiley & Sons, Ltd.     

Process influences on the structure,piezoelectric, and gas‐barrier properties of PVDF‐TrFE copolymer

The influence of annealing between the Curie transition and the melting point of solvent cast polyvinylidene fluoride trifluoroethylene copolymer films on the crystalline structure, mechanical and electrical properties, and oxygen permeability is investigated. Annealing leads to remarkable changes in the structure and properties of the copolymer, within the first four hours of treatment, and with kinetics depending on the temperature. The crystallinity increases by 19% (relative), resulting in a 10 K increase in the Curie transition, a 4 K increase of the melting temperature and a 2 K decrease in the glass transition temperature. A crystalline phase transition from the paraelectric α‐phase to the ferroelectric β‐phase is also evidenced using in‐situ X‐ray diffraction. The elastic modulus is found to increase by more than three‐fold at room temperature and the loss peak at the glass transition is considerably reduced. The piezoelectric coefficient is found to increase by 40% and the dielectric properties are significantly changed. The most remarkable influence is the ten‐fold reduction of the oxygen permeability, with a drastic reduction of the activation energy for oxygen transport. The improvement in oxygen barrier properties of the annealed copolymer is attributed to the restricted mobility of oxygen molecules in the semicrystalline polymer with nanometer sized crystallites. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 496–506     

Synthesis of W‐doped TiO2 by low‐temperature hydrolysis: Effects of annealing temperature and doping content on the surface microstructure and photocatalytic activity

A series of tungsten‐doped Titania photocatalysts were synthesized using a low‐temperature method. The effects of dopant concentration and annealing temperature on the phase transitions, crystallinity, electronic, optical, and photocatalytic properties of the resulting material were studied. The X‐ray patterns revealed that the doping delays the transition of anatase to rutile to a high temperature. A new phase W_yTi_1‐yO₂ appeared for 5.00 wt% W‐TiO₂ annealed at 900 °C. Raman and diffuse reflectance UV–Vis spectroscopy showed that band gap values decreased slightly up to 700 °C. X‐ray photoelectron spectroscopy showed that surface species viz. Ti³⁺, Ti⁴⁺, O^2?, oxygen‐vacancies, and adsorbed OH groups vary depending on the preparation conditions. The photocatalytic activity was evaluated via the degradation of methylene blue using LED white light. The degradation rate was affected by the percentage of dopants. The best photocatalytic activity was achieved with the sample labeled 5.00 wt% W‐TiO₂ annealed at 700 °C.     

Annealing‐induced increase of permeability and amorphous‐phase mobility in an ethylene–vinylacetate copolymer

The 50% increased permeability after annealing of semicrystalline poly(ethylene/vinylacetate) containing 3 mol % vinylacetate is linked to increased mobility in the amorphous phase, as identified by line‐narrowing of ¹H wideline nuclear magnetic resonance (NMR) spectra and by reduced cross‐polarization efficiency in ¹³C NMR. Other morphological parameters, such as crystallinity, measured as 30 to 35% by differential scanning calorimetry (DSC) and NMR, are hardly changed by annealing. Small‐angle X‐ray scattering and NMR studies, using spin diffusion as well as T_1ρ and T₁ relaxation, detected only a small increase in crystallite thickness. The annealing‐induced enhancement in segmental mobility in the amorphous regions corresponds to a temperature shift of about 10 K, from which an increase of the motional rate by a factor of 2 is estimated, and which can account for the enhancement in the permeability. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2774–2780, 2001     

Phase transitions of the rapid‐compression‐induced mesomorphic isotactic polypropylene under high‐pressure annealing

The mesomorphic isotactic polypropylene was prepared by rapid compression instead of the common method of temperature quenching, and their phase transition under high pressure was investigated in depth by combining wide‐angle X‐ray diffraction, small‐angle X‐ray scattering, and differential scanning calorimetry techniques. It was found that annealing under pressure can promote the further arrangement of chain segments of the mesophase toward the crossed state in the orthorhombic γ‐phase, and the long period of the mesophase slightly decreased from 8.2 to 7.2 nm. The kinetics of this meso‐γ transition strongly depends on pressure. As annealing pressure increased, the mobility of molecular segments was reduced, and then the onset and finishing time of phase transition were both delayed significantly. A critical annealing pressure was found between 1.6 and 1.75 GPa, which determines whether the phase transition occurs or not. When pressure reaches 1.75 GPa, mesophase did not transform at all within 120 min. Based on the results, a reasonable mechanism was proposed to show the crystallization process of mesophase under high‐pressure annealing. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 651–661     

Radiation damage in polymer films from grazing‐incidence X‐ray scattering measurements

Grazing‐incidence X‐ray scattering (GIXS) is widely used to analyze the crystallinity and nanoscale structure in thin polymer films. However, ionizing radiation will generate free radicals that initiate crosslinking and/or chain scission, and structural damage will impact the ordering kinetics, thermodynamics, and crystallinity in many polymers. We report a simple methodology to screen for beam damage that is based on lithographic principles: films are exposed to patterns of X‐ray radiation, and changes in polymer structure are revealed by immersing the film in a solvent that dissolves the shortest chains. The experiments are implemented with high throughput using the standard beam line instrumentation and a typical GIXS configuration. The extent of damage (at a fixed radiation dose) depends on a range of intrinsic material properties and experimental variables, including the polymer chemistry and molecular weight, exposure environment, film thickness, and angle of incidence. The solubility switch for common polymers is detected within 10–60 s at ambient temperature, and we verified that this first indication of damage corresponds with the onset of network formation in glassy polystyrene and a loss of crystallinity in polyalkylthiophenes. Therefore, grazing‐incidence X‐ray “patterning” offers an efficient approach to determine the appropriate data acquisition times for any GIXS experiment. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1074–1086     

Polypropylene/montmorillonite nanocomposites toughened with SEBS‐g‐MA: Structure–property relationship

Polypropylene (PP)/organo‐montmorillonite (Org‐MMT) nanocomposites toughened with maleated styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) were prepared via melt compounding. The structure, mechanical properties, and dynamic mechanical properties of PP/SEBS‐g‐MA blends and their nanocomposites were investigated by X‐ray diffraction (XRD), polarizing optical microscopy (POM), tensile, and impact tests. XRD traces showed that Org‐MMT promoted the formation of β‐phase PP. The degree of crystallinity of PP/SEBS‐g‐MA blends and their nanocomposites were determined from the wide angle X‐ray diffraction via profile fitting method. POM experiments revealed that Org‐MMT particles served as nucleating sites, resulting in a decrease of the spherulite size. The essential work of fracture approach was used to evaluate the tensile fracture toughness of the nanocomposites toughened with elastomer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3112–3126, 2005     

Rheology and crystallization behavior of PLLA/TiO2‐g‐PDLA composites

Poly(L‐lactide) (PLLA) composites with TiO₂‐g‐poly(D‐lactide) (PDLA), which was synthesized by surface‐initiated opening ring polymerization with TiO₂ as initiator and Sn(Oct)₂ as catalyst, were prepared by solution casting. The synthesized TiO₂‐g‐PDLA was characterized by transmission electron microscope (TEM) and dynamic laser scattering (DLS), showing larger size corresponding to that of TiO₂. Fourier transform infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS) measurements were further carried out and indicated that PDLA was grafted onto TiO₂ through covalent bond. For PLLA/TiO₂‐g‐PDLA composites, the stereocomplex crystallites were formed between PDLA grafted on the surface of TiO₂ and the PLLA matrix, which was determined by FT‐IR, differential scanning calorimetry (DSC), and X‐ray diffractometer (XRD). The influence of stereocomplex crystallites on the rheological behavior of PLLA/TiO₂‐g‐PDLA was investigated by rheometer, which showed greater improvement of rheological properties compared to that of PLLA/TiO₂ composites especially with a percolation content of TiO₂‐g‐PDLA between 3 wt%–5 wt%. The crystallization and melting behavior of PLLA/TiO₂‐g‐PDLA composites were studied by DSC under different thermal treatment conditions. The formed PLA stereocomplex network acted as nucleating agents and a special interphase on the functional surface of TiO₂, which resulted in imperfect PLLA crystal with lower melting temperature. When the thermal treatment was close to the melting temperature of PLA stereocomplex, the crystallinity approached to the maximum. The isothermal crystallization study by polarizing microscope (POM) indicated that stereocomplex network presented stronger nucleation capacity than TiO₂‐g‐PDLA. Copyright © 2015 John Wiley & Sons, Ltd.     

Online wide‐angle X‐ray diffraction/small‐angle X‐ray scattering measurements for the CO2‐laser‐heated drawing of poly(ethylene terephthalate) fiber

Fiber‐structure‐development in the poly(ethylene terephthalate) fiber drawing process was investigated with online measurements of wide‐angle and small‐angle X‐ray scattering with both a high‐luminance X‐ray source and a CO₂‐laser‐heated drawing system. The intensity profile of the transmitted X‐ray confirmed the location of the neck‐drawing point. The diffraction images had a time resolution of several milliseconds, and this still left much room for improvement. Crystal diffraction appeared in the wide‐angle X‐ray images almost instantaneously about 20 ms after necking, whereas a four‐point small‐angle X‐ray scattering pattern appeared immediately after necking. With the elapse of time after necking, the four‐point scattering pattern changed into a meridional two‐point shape. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1090–1099, 2005     

Structure characterization of copolymers of ethylene and 1‐octadecene

Four ethylene‐1‐octadecene copolymers and the corresponding polyethylene homopolymer, synthesized with a metallocene catalyst, have been analyzed by using three characterization techniques in the solid state: differential scanning calorimetry, wide‐angle X‐ray diffraction, and Raman spectroscopy. Very important annealing effects are observed in the copolymers with higher comonomer content while standing at room temperature, in such a way that the enthalpies of melting derived from the first and second melting are different. The X‐ray diffractograms have been analyzed in terms of amorphous and crystalline components, determining both the crystallinity and the position of the different reflections. The variation of the unit cell parameters has been calculated from those reflections. No indication of a possible participation of the relatively long 1‐octadecene branches in the crystallization can be deduced from the X‐ray data. The degree of crystallinity has also been determined from the Raman spectra, following two procedures. The results indicate that the crystallinities deduced from the band at 1416 cm⁻¹ are much lower than those derived from the other two characterization techniques. On the contrary, the data from the 1060 cm⁻¹ band are practically coincident with the X‐ray determinations. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1440–1448, 2000     

Differential scanning calorimetry,small‐angle X‐ray scattering,and wide‐angle X‐ray scattering on homogeneous and heterogeneous ethylene‐α‐copolymers

The objective of this work was to use both X‐ray and differential scanning calorimetry techniques in a comparative study of the lamellar and crystalline structures of heterogeneous and homogeneous ethylene‐α‐copolymers. The samples differed in the comonomer type (1‐butene, 1‐hexene, 1‐octene, and hexadecene), comonomer content, and catalyst used in the polymerizations. Step crystallizations were performed with differential scanning calorimetry, and the crystallinity and lamellar thicknesses of the different crystal populations were determined. Wide‐angle X‐ray scattering was used to determine crystallinities, average sizes of the crystallites, and dimensions of the orthorhombic unit cell. The average thickness, separation of the lamellae, and volume fractions of the crystalline phase were determined by small‐angle X‐ray scattering (SAXS). The results revealed that at densities below 900 kg/m³, polymers were organized as poorly organized crystal bundles. The lamellar distances were smaller and the lamellar thickness distributions were narrower for the homogeneous ethylene copolymers than for the heterogeneous ones. Step‐crystallization experiments by SAXS demonstrated that the long period increased after annealing. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1860–1875, 2001     

Mechanical properties of oriented low‐density polyethylene with an oriented lamellar‐stack morphology

A quantitative study was undertaken of the anisotropy of low‐strain mechanical behavior for specially oriented polyethylene with controlled crystalline and lamellar orientation. The samples were prepared by the die drawing of injection‐molded rods of polyethylene and annealing. This produced a parallel lamellar structure for which a simple, three‐dimensional composite laminate model could be used to calculate the expected anisotropy. Experimental data, including X‐ray strain measurements of the lateral crystalline elastic constants, showed good quantitative agreement with the model prediction. The X‐ray strain measurements confirmed that the amorphous regions exert large constraints on the crystalline phase in the lateral directions, where an order of magnitude difference was found between the measured apparent lateral crystalline compliances in the lamellar‐stack sample and the expected values for a perfect crystal. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 755–764, 2000     

Morphology changes in bulk donor–acceptor poly(benzodithiophene‐benzotriazole) after post‐treatment

The bulk order in donor–acceptor poly(benzodithiophene‐benzotriazole) was improved by two different post‐treatment procedures applied to the specimen. Two‐dimensional wide‐angle X‐ray scattering was used to investigate the structural changes after treatment. After post‐treatment the polymer turned into a highly crystalline morphology with well‐resolved and intensive π‐stacking reflections which were absent in the pristine sample. To understand the ordering mechanisms taking place during the two post‐treatment procedures, structural parameters like coherence length and paracrystallinity were extracted from the X‐ray data indicating the impact on crystallite size and cumulative lattice disorder. During temperature annealing the intralayer packing transforms from amorphous to highly ordered. On the other hand, solvent vapor annealing enhances in higher extent the interlayer organization due to interpenetration of solvent molecules between alkyl side chains. These results provide important insights for the morphology optimization of semicrystalline conjugated polymers. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2327–2334.     

Crystalline β‐structure of PHBV grown epitaxially on silicate layers of MMT

The poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV)/montmorillonite(MMT) nanocomposites were investigated by wide‐angle X‐ray scattering (WAXS). The aim of the investigation was solution intercalation of MMT with PHBV. Beside the usual orthorhombic unit cell, a stable pseudohexagonal β‐structure of PHBV was obtained. Well known β‐structure has one common WAXS reflection (d = 0.480 nm), which corresponds to the mean distance of PHBV chains in the pseudohexagonal structure. The new β‐structure has two diffraction peaks in the WAXS pattern. It is a three‐dimensionally ordered crystalline structure oriented in parallel with the silica layers of MMT. The new polymorphic form is supposed to be growing on the layers of MMT. Its layers serve as primary nucleation centers for epitaxial growth of the β‐structure. After annealing, this polymorphic form of PHBV disappears and it is transformed into the more stable α‐form leading to an enhanced total crystallinity of the polymer comprised in the nanocomposite. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 751–755, 2009     

Preparation and application of a novel core–shell‐particle‐supported zirconocene catalyst

The use of functional groups bearing silica/poly(styrene‐co‐4‐vinylpyridine) core–shell particles as a support for a zirconocene catalyst in ethylene polymerization was studied. Several factors affecting the behavior of the supported catalyst and the properties of the resulting polymer, such as time, temperature, Al/N (molar ratio), and Al/Zr (molar ratio), were examined. The conditions of the supported catalyst preparation were more important than those of the ethylene polymerization. The state of the supported catalyst itself played a decisive role in both the catalytic behavior of the supported catalyst and the properties of polyethylene (PE). IR and X‐ray photoelectron spectroscopy were used to follow the formation of the supports. The formation of cationic active species is hypothesized, and the performance of the core–shell‐particle‐supported zirconocene catalyst is discussed as well. The bulk density of the PE formed was higher than that of the polymer obtained from homogeneous and polymer‐supported Cp₂ZrCl₂/methylaluminoxane catalyst systems. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2085–2092, 2001     

Effect of postcasting heat‐treatment on the structure and properties of semicrystalline phase‐inversion poly(vinylidene fluoride) membranes

Microporous PVDF membranes were prepared by immersion‐precipitation in 1‐octanol of casting dopes dissolved at different temperatures, with dissolution temperature affecting strongly the membrane microstructure. The effect of postcoagulation thermal annealing, which is an additional thermal parameter, on membrane microstructure and properties is probed herein. Membranes obtained were annealed at temperatures up to 160 °C, which is close to the melting point of PVDF polymer. Annealing leads to a substantial modification of the nano‐scale fine structure of the membranes, while the overall‐microporous structure is preserved. At elevated annealing temperatures, nano‐grains, fibrils, and stick‐like crystalline entities gradually eclipse, while globules develop more robust connections based on wide bands of crystal elements. Probing by X‐ray diffraction and dynamic scanning calorimetry shows that crystallinity increases when annealing temperature and time are increased. As regards mechanical properties, the tensile strength of the membranes can be enhanced substantially, up to about 10 times, upon appropriate high temperature prolonged annealing. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1880–1893, 2009     

Structure‐property relationships in exfoliated polyisoprene/clay nanocomposites

Structure‐property relationships in exfoliated polyisoprene (PI)/clay nanocomposites have been studied as a function of the clay concentration with rheometry, X‐ray diffraction, small‐angle X‐ray scattering, and transmission electron microscopy. The results presented here indicate that the interlayer spacing of layered silicates increases from 2 to at least approximately 14 nm because of the penetration of polymer molecules into the spacing between the silicate layers. The average aspect ratio (width/thickness) of the dispersed nanoplates is also estimated to be at least approximately 80. Additionally, the storage modulus of the nanocomposite exhibits frequency‐independent pseudo‐solidlike behavior above the percolation threshold [volume fraction of clay at the percolation threshold (?_p) = 0.02] and shows large enhancements (up to approximately six orders of magnitude) in comparison with the storage modulus of PI when the volume fraction of clay (?) is greater than ?_p. For the shear‐aligned PI/clay nanocomposites, an increase in the storage modulus with shear alignment is observed at ? < ?_p, whereas a decrease in the storage modulus is observed for ? > ?_p. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1000–1009, 2004     

High‐performance poly(ethylene‐2,6‐naphthalate) fiber prepared by high‐tension annealing

A high‐tension annealing (HTA) method has been applied to zone‐annealed poly(ethylene‐2,6‐naphthalate) (PEN) fibers in order to further improve their mechanical properties. The HTA treatment was carried out under an applied tension of 428 MPa at a treating temperature of 175 °C. The applied tension was close to the tensile strength at 175 °C. The resulting HTA fiber had a birefringence of 0.492 and degree of crystallinity of 57%. Wide‐angle X‐ray diffraction (WAXD) photographs of the HTA fibers showed three reflections (010, 100, and 1 10) attributed to an α form crystal, but no (020) reflection attributed to a β form was observed in the equator. The tensile modulus and tensile strength increased with processing, and the HTA fiber had a maximum modulus of 33 GPa, a tensile strength of 1.1 GPa, and a storage modulus of 33 GPa at 25 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 61–67, 2000     

Effect of the initial matrix material on the structure of radiation‐grafted ion‐exchange membranes: Wide‐angle and small‐angle X‐ray scattering studies

Seven different fluoropolymer films were used as matrix materials for radiation‐grafted ion‐exchange membranes. The crystallinity and preferred orientation of these membranes were studied with wide‐angle X‐ray scattering, and the lamellar structure of the membranes was examined with small‐angle X‐ray scattering. The crystallinity of poly(vinylidene fluoride) (PVDF)‐based matrix materials varied between 57 and 40%, and the crystallinity of the sulfonated samples varied between 34 and 23%. The lamellar periods of PVDF‐based matrix materials were about 115 Å, and the lamellar periods of poly(ethylene‐alt‐tetrafluoroethylene) and poly(tetrafluoroethylene‐co‐hexafluoropropylene) were 250 and 212 Å, respectively. When the samples were grafted, the lamellar periods increased. Correlation function analysis showed very clearly that the long‐range order decreased because of grafting and sulfonation processes. For those samples that showed good proton conductivity, the lamellar period also increased because of sulfonation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1539–1555, 2002