Biodegradable highly porous interconnected poly(ε-caprolactone)/poly(L-lactide-co-ε-caprolactone) scaffolds by supercritical foaming for small-diameter vascular tissue engineering

Biodegradable ?4 mm tubular porous poly(ε-caprolactone)/poly(L-lactide-co-ε-caprolactone) (PCL/PLCL) scaffolds are fabricated successfully via one-step microcellular supercritical carbon dioxide foaming process. The effect of blending ratio on the rheology, pore structures, mechanical property, wettability, and biocompatibility of PCL/PLCL blends tubular scaffold are reported. Rheological results show that PCL matrix and PLCL dispersed phase has good compatibility. The melt strength of PCL can be enhanced obviously by adding PLCL. With an increase of PLCL content from 10 to 30 wt%, the pore size increases from 7.6 to 24.9 μm due to the homogeneous nucleation effect. The maximum open-cell content can reach 77% for PCL/PLCL foamed sample. Cyclical tensile and compliance tests show that few content of dispersed PLCL (10–20 wt%) improves the flexibility and recoverability. Cell viability results demonstrate that human umbilical vein endothelial cells (HUVECs) cultured on all PCL/PLCL porous scaffolds exhibit a typical spindle-like cell morphology. Moreover, HUVECs have a higher density and spreading areas on surface of 10% PLCL scaffold. The results gathered in this paper may open a new perspective for the fabrication of small-diameter vascular tissue engineering scaffold.     

3D printed PCL scaffold reinforced with continuous biodegradable fiber yarn: A study on mechanical and cell viability properties

In this study, poly (ε‐caprolactone) (PCL) scaffolds were printed and reinforced, simultaneously, with biodegradable poly glycolic acid (PGA) suture yarn, as a continuous reinforcing fiber, in the Fused Deposition Modeling (FDM) 3D printing process. Albeit PCL is a suitable material for biomedical applications, its low mechanical properties, and low degradation rate have limited its usage. A biocompatible suture yarn was used as the reinforcing material to enhance the mechanical properties and biodegradation characteristics, via an innovative method of continuous fiber embedding in the FDM process. The reinforced PCL samples were 3D printed with the setting porosity value of 60% and 0°/60°/120° lay-down pattern. The mechanical and biological properties of the scaffolds were tested to prove the effectiveness of the produced scaffolds for bone substitute purposes. Mechanical properties assessments showed that with a 22 vol.% suture yarn content in the 3D printed PCL scaffolds, the tensile strength, and elastic modulus remarkably increased up to 374% and 775%, respectively. The degradation of the reinforced PCL was 20 times higher than that of the non-reinforced PCL samples, after ten weeks, dominated by the fiber degradation phenomenon. After three days of cell culture, the proliferation assay of the built scaffovd the non-toxicity of the reinforced PCL.     

Poly(lactic acid)/coplasticized thermoplastic starch blend: Effect of plasticizer migration on rheological and mechanical properties

Polylactic acid (PLA) and thermoplastic starch (TPS) are known as bio‐based and biodegradable thermoplastic polymers that can be used in different applications owing to their inherent physical and mechanical properties. In order to reduce the higher costs of PLA and tuning its physical and mechanical properties suitable for short life packaging applications, blending of PLA with the TPS, more economical biodegradable polymer, has been considered in academic and industrial researches. However, melt blending of PLA with TPS without compatibilization process caused some drawbacks such as coarsening morphology and declining mechanical properties and ductility because of thermodynamic immiscibility, which may restrict its usage in packaging applications. Subsequently, our approach in this research is compatibilization of PLA/TPS blends by utilization of primary well tuning of TPS formulation with a combination of sorbitol and glycerol plasticizers. In this work, the wide composition range of melt mixed PLA/TPS blends was prepared using a laboratory twin screw extruder. The effects of microstructure on the rheological and mechanical properties of PLA/TPS blends were studied using different methods such as scanning electron microscopy (SEM) images, contact angle, oscillatory shear rheological measurements, and tensile and impact strength mechanical tests. The rheological and mechanical properties were interpreted according to the morphological features and considering the possibility of plasticizer migration from TPS to PLA phase during melt blending. Reduction in complex viscosity and storage modulus of PLA matrix samples indicates the improved melt processability of blends. Finally, in comparison with mechanical results reported in literature, our simple approach yielded the blends with elastic modulus and ductility comparable with those of chemically compatibilized PLA/TPS blends.     

The electrospun poly(ε‐caprolactone)/fluoridated hydroxyapatite nanocomposite for bone tissue engineering

Biodegradable cell‐incorporated scaffolds can guide the regeneration process of bone defects such as physiological resorption, tooth loss, and trauma which medically, socially, and economically hurt patients. Here, 0, 5, 10, and 15 wt% fluoridated hydroxyapatite (FHA) nanoparticles containing 25 wt% F^? and 75 wt% OH^? were incorporated into poly(ε‐caprolactone) (PCL) matrix to produce PCL/FHA nanocomposite scaffolds using electrospinning method. Then, scanning electron microscopy (SEM), X‐ray diffraction (XRD) pattern, and Fourier transform infrared spectroscopy (FTIR) were used to evaluate the morphology, phase structure, and functional groups of prepared electrospun scaffolds, respectively. Furthermore, the tensile strength and elastic modulus of electrospun scaffolds were investigated using the tensile test. Moreover, the biodegradation behavior of electrospun PCL/FHA scaffolds was studied by the evaluation of weight loss of mats and the alternation of pH in phosphate buffer saline (PBS) up to 30 days of incubation. Then, the biocompatibility of prepared mats was investigated by culturing MG‐63 osteoblast cell line and performing MTT assay. In addition, the adhesion of osteoblast cells on prepared electrospun scaffolds was studied using their SEM images. Results revealed that the fiber diameter of prepared electrospun PCL/FHA scaffolds alters between 700 and 900 nm. The mechanical assay illustrated the mat with 10 wt% FHA nanoparticles revealed the highest tensile strength and elastic modulus. The weight loss alternation of mats determined around 1% to 8% after 30 days of incubation. The biocompatibility and cell adhesion of mats improved by increasing the amounts of FHA nanoparticles.     

Poly(lactic acid)/poly(butylene succinate)/calcium sulfate whiskers biodegradable blends prepared by vane extruder: Analysis of mechanical properties,morphology, and crystallization behavior

Ternary blends of PLA/PBS/CSW with different weight fractions were prepared using a vane extruder. The mechanical properties, morphology, crystallization behavior and thermal stability of the blends were investigated. For the PLA/CSW blend, the tensile strength decreased, the flexural strength and modulus increased compared with pure PLA. For PBS, the addition of CSW had little influence on the mechanical properties. For the ternary blends PLA/PBS/CSW, the tensile strength, flexural strength and modulus decreased compared with pure PLA, while the elongation at break and the impact strength increased significantly. The brittle-ductile transition of the blends took place when the PBS weight fraction reaching 30 wt%. As a soft component in the blends, PBS was beneficial to improve the tensile ductility and the toughness of PLA. SEM measurements reveal that PLA/PBS/CSW blends were immiscible. When the weight fraction of PBS was 50 wt%, significant phase separation was observed, and CSW had preferential location in the PBS phase of the blend. DSC measurement and POM observation reveal that CSW had a heterogeneous nucleation effect on PLA and PBS matrix. The addition of PBS improved the crystallization of PLA and the thermal resistance of the PLA/PBS/CSW blends significantly.     

聚乙烯-g-聚苯乙烯对线性低密度聚乙烯/聚苯乙烯共混物机械性能和发泡行为的影响

以通过开环易位聚合、加氢反应和原子转移自由基聚合技术结合制备的聚乙烯-g-聚苯乙烯(PE-g-PS)作为增容剂,研究了加入不同PS支链长度的PE-g-PS对于线性低密度聚乙烯/聚苯乙烯(LLDPE/PS)共混物的机械性能和发泡行为的影响。 以典型组成m(LLDPE):m(PS)=70:30共混物为例,考察了PE-g-PS对共混物拉伸性能的影响。 相对于二元共混物,增容剂的加入使得断裂伸长率、拉伸强度和屈服强度皆提高,且含长PS支链的增容体系提高更明显。 采用超临界CO₂釜式发泡工艺,考察了PE-g-PS中PS支链长度对共混物发泡行为的影响。 结果表明,相对于短PS支链体系,加入PE-g-PS_1.59k(PS相对分子质量为1590)后的泡孔结构更加均一,完全没有“缝隙”形貌的出现。 当发泡温度降至80 ℃时,即使存在LLDPE发泡空间限制作用(LLDPE无法发泡),加入支链长度更长的PE-g-PS_1.59k后泡孔分布也更加均一。     

Porous-conductive chitosan scaffolds for tissue engineering, 1. Preparation and characterization

Novel porous-conductive chitosan scaffolds were fabricated by incorporating conductive polypyrrole (PPy) particles into a chitosan matrix and employing a phase separation technique to build pores inside the scaffolds. Conductive polypyrrole particles were prepared with a microemulsion method using FeCl3 as a dopant. The preparation conditions were optimized to obtain scaffolds with controlled pore size and porosity. The conductivity of the scaffolds was investigated using a standard four-point probe technique. It was found that several kinds of scaffolds showed a conductivity close to 10(-3) S.cm(-1) with a low polypyrrole loading of around 2 wt.-%. The main mechanical properties, such as tensile strength, breaking elongation and Young's modulus of the scaffolds, were examined both in the dry and in the hydrated states. The results indicated that a few different kinds of scaffolds exhibited the desired mechanical strength for some tissue engineering applications. The miscibility of polypyrrole and chitosan was also evaluated using a dynamic mechanical method. The presence of significant phase separation was detected in non-porous PPy/chitosan scaffolds but enhanced miscibility in porous PPy/chitosan scaffolds was observed.     

The effect of 3D printing on the morphological and mechanical properties of polycaprolactone filament and scaffold

Three‐dimensional (3D) printing becomes an attractive technique to fabricate tissue engineering scaffolds through its high control on fabrication and repeatability using the printing parameters. This technique can be combined by the finite element method (FEM), and tissue‐specific scaffolds with desirable morphological and mechanical properties can be designed and manufactured. In this study, the influential 3D printing parameters on the morphological and mechanical properties of polycaprolactone (PCL) filament and scaffold were studied experimentally and numerically. First, the effects of printing parameters and process on the properties of extruded PCL filament were investigated. Then, using FEM, the effects of filament specifications on the overall characteristics of the scaffold were evaluated. Results showed that both the printing process in terms of resting time and remaining time and the printing parameters like pressure, printing speed, and printing path length have influenced the filament properties. In addition, both the filament diameter and elastic modulus had significant effects on the properties of scaffold especially, a 20% increase in the filament diameter caused the scaffold compressive elastic modulus to rise by around 72%. It is concluded that the printing parameters and process must be tuned very well in fabricating scaffolds with the desired morphology and mechanical property.     

Effects of Modified MMT on Mechanical Properties of EVA/MMT Nanocomposites and Their Foams

In this study, nanocomposites of poly(ethylene-co-vinyl acetate) with two kinds of organically modified montmorillonite (OMMT) were prepared by melt intercalation. Their structures and mechanical properties were characterized by X-ray diffraction (XRD) and tensile test respectively. Especially, foaming of these nanocomposites mixed with chemical blowing agent was carried out through compression molding. Influences of OMMT on foaming ratio and mechanical properties were investigated by density test, tensile test and tear test. Results revealed that both kinds of OMMT with proper content increased tensile strength and Young's modulus of nanocomposites without a compromise of elongation at break. For foaming, OMMTs apparently improved foaming ratio and in particular, one of them can improve tear strength, tensile strength, Young's modulus and elongation although the density was decreased.     

微孔聚乳酸支架材料的热稳定性与动态热机械特性

采用无溶剂二氧化碳固态发泡技术,在2.5、3.5、4.0和5.0 MPa饱和压力下制备了泡孔孔径为350-20μm的聚乳酸支架材料.利用热重分析技术、动态热机械分析技术和扫描电子显微镜技术,测定了材料的起始分解温度、分解速率、储存/损耗模量和损耗因子等参数,并利用Kissinger、Ozawa-Doyle和Vyazovkin方程进行了热分解动力学计算,推算了氮气环境下材料的降解时间和使用寿命.结果表明,随着发泡压力的减小,支架材料的泡孔孔径增大,材料的柔韧性增强,表观活化能降低,降解时间缩短.     

Advances in properties and biodegradability of co-continuous,immicisible, biodegradable,polymer blends

A series of blends consisting of polylactic acid (PLA) and aliphatic succinate polyester (Bionolle#3000) have been prepared. The results of the mechanical property investigation have shown that using more than 20 wt % Bionolle#3000 can significantly increase the toughness of the PLA, increase the elongation at break (more than 200%) and increase the impact strength (more than 70 J/m). These properties were not significantly affected by the aging behavior of PLA for more than two months. DMA results show that Bio#3000 reduces the elastic modulus of the blends between −15°C and 60°C. Soil degradation rates of the PLA/Bio#3000 blends also increase with increasing Bio#3000 content. However, for the blends with less than 30 wt % of Bio#3000, the degradation rates do not significantly increase. Enzymatic degradation rates of the blends are higher than for those of the two polymers, and these rates increase with increasing PLA content. Composting biodegradation rates increase with increasing Bio#3000 content.     

微生物合成的β-羟基丁酸酯与β-羟基已酸酯共聚物/聚乳酸共混材料(PHBHHx/PLA)的力学性能与生物降解性研究

通过熔融共混法制备了聚乳酸/微生物产β-羟基丁酸酯与β-羟基己酸共聚物的共混物(PLA/PHBHHx).采用拉伸力学试验研究了共混物的力学性能.通过土壤悬浊培养降解法和扫描电子显微镜(SEM)分析对共混材料的生物降解性能进行了研究.实验结果表明,随着PHBHHx含量的增加,共混物的拉伸强度和杨氏模量降低,而生物降解速率却显著提高.但是,在175h之前,重量组成比为20/80的共混物降解速率比纯PHBHHx还要快.综合分析表明,共混材料PLA/PHBHHx的重量比为20/80时,具有优良的力学性能和生物降解性.     

微生物合成的β-羟基丁酸酯与β-羟基己酸酯共聚物/聚乳酸共混材料(PHBHHx/PLA)的力学性能与生物降解性研究

通过熔融共混法制备了聚乳酸/微生物产β-羟基丁酸酯与β-羟基己酸共聚物的共混物(PLA/PHBHHx)。采用拉伸力学试验研究了共混物的力学性能。通过土壤悬浊培养降解法和扫描电子显微镜(SEM)分析对共混材料的生物降解性能进行了研究。实验结果表明,随着PHBHHx含量的增加,共混物的拉伸强度和杨氏模量降低,而生物降解速率却显著提高。但是,在175h之前,重量组成比为20/80的共混物降解速率比纯PHBHHx还要快。综合分析表明,共混材料PLA/PHBHHx的重量比为20/80时,具有优良的力学性能和生物降解性。     

Incorporation of nanohydroxyapatite and vitamin D3 into electrospun PCL/Gelatin scaffolds: The influence on the physical and chemical properties and cell behavior for bone tissue engineering

Scaffold, an essential element of tissue engineering, should provide proper physical and chemical properties and evolve suitable cell behavior for tissue regeneration. Polycaprolactone/Gelatin (PCL/Gel)‐based nanocomposite scaffolds containing hydroxyapatite nanoparticles (nHA) and vitamin D3 (Vit D3) were fabricated using the electrospinning method. Structural and mechanical properties of the scaffold were determined by scanning electron microscopy (SEM) and tensile measurement. In this study, smooth and bead‐free morphology with a uniform fiber diameter and optimal porosity level with appropriate pore size was observed for PCL/Gel/nHA nanocomposite scaffold. The results indicated that adding nHA to PCL/Gel caused an increase of the mechanical properties of scaffold. In addition, chemical interactions between PCL, gelatin, and nHA molecules were shown with XRD and FT‐IR in the composite scaffolds. MG‐63 cell line has been cultured on the fabricated composite scaffolds; the results of viability and adhesion of cells on the scaffolds have been confirmed using MTT and SEM analysis methods. Here in this study, the culture of the osteoblast cells on the scaffolds showed that the addition of Vit D3 to PCL/Gel/nHA scaffold caused further attachment and proliferation of the cells. Moreover, DAPI staining results showed that the presence and viability of the cells were greater in PCL/Gel/nHA/Vit D3 scaffold than in PCL/Gel/nHA and PCL/Gel scaffolds. The results also approved increasing cell proliferation and alkaline phosphatase (ALP) activity for MG‐63 cells cultured on PCL/Gel/nHA/Vit D3 scaffold. The results indicated superior properties of hydroxyapatite nanoparticles and vitamin D3 incorporated in PCL/Gel scaffold for use in bone tissue engineering.     

Structure and blood compatibility of highly oriented poly(lactic acid)/thermoplastic polyurethane blends produced by solid hot stretching

Highly oriented poly(lactic acid) (PLA)/thermoplastic polyurethane (TPU) blends were fabricated through solid hot stretching technology in an effort to improve the mechanical properties and blood biocompatibility of PLA as blood‐contacting medical devices. It was found that the tensile strength and modulus of the blends can be improved dramatically by stretching. With the increase of draw ratio, the cold crystallization peak became smaller, and the glass transition and the melting peak moved to high temperature, while the crystallinity increased, and the grain size of PLA decreased, indicating of the stress‐induced crystallization during drawing. The oriented blends exhibited structures with longitudinal striations which indicate the presence of micro‐fibers. TPU phase was finely and homogeneously dispersed in the PLA, and after drawing, TPU domains were elongated to ellipsoid. The introduction of TPU and orientation could enhance the blood compatibility of PLA by prolonging kinetic clotting time, and decreasing hemolysis ratio and platelet activation. Copyright © 2013 John Wiley & Sons, Ltd.     

Properties of immiscible and ethylene-butyl acrylate-glycidyl methacrylate terpolymer compatibilized poly (lactic acid) and polypropylene blends

Poly(lactic acid) (PLA) and polypropylene (PP) blends of various proportions were prepared by melt-compounding. The miscibility, phase morphology, thermal behavior, and mechanical and rheological properties of the blends were investigated. The blends were immiscible systems with two typical morphologies, spherical droplet and co-continuous, and could be obtained at various compositions. Complex viscosity, storage modulus and loss modulus depend on the PP content. Thermal degradation of all blends led to two weight losses, for PLA and PP. The incorporation of PP improved the thermal stability of the blend. The effect of compatibilizer (ethylene-butyl acrylate-glycidyl methacrylate terpolymer, EBA-GMA) on the morphology and mechanical properties of 70/30 w/w PLA/PP blends was investigated. The tensile strength of these blends reached a maximum for 2.5 wt% EBA-GMA, and impact strength increased with increasing EBA-GMA content, suggesting that EBA-GMA is an effective compatibilizer for PLA/PP blends.     

Preparation and properties of poly(lactic acid)/cellulolytic enzyme lignin/PGMA ternary blends

Poly(lactic acid)-based ternary blends consisting of poly(lactic acid)(PLA),cellulolytic enzyme lignin(CEL),and polyolefine grafting maleic anhydride(PGMA) were prepared by extrusion blending and the mechanical properties and the morphology of the ternary blends were investigated.It was found that the mechanical properties varied with various loading of the components in the blends.Compared to neat PLA,the tensile strength and the Young’s modulus of the ternary blends were decreased,but the elongation at break and the impact strength were effectively improved.Scanning electron microscope observations revealed that the CEL plays a bridging role between PLA and PGMA,enhancing the miscibility between them and resulting in the improvement of ductility and toughness of the ternary blends.Considering the cost and performance,we obtained the optimal blend PLA/CEL/ PGMA(80/20/20,w/w/w),of which the impact strength and the elongation at break were doubled as that of neat PLA,and the tensile strength remained moderate.     

Cell(MC3T3‐E1)‐Printed Poly(ϵ‐caprolactone)/Alginate Hybrid Scaffolds for Tissue Regeneration

A new cell‐printed scaffold consisting of poly(ϵ‐caprolactone) (PCL) and cell‐embedded alginate struts is designed. The PCL and alginate struts are stacked in an interdigitated pattern in successive layers to acquire a three‐dimensional (3D) shape. The hybrid scaffold exhibits a two‐phase structure consisting of cell (MC3T3‐E1)‐laden alginate struts able to support biological activity and PCL struts able to provide controllable mechanical support of the cell‐laden alginate struts. The hybrid scaffolds exhibit an impressive increase in tensile modulus and maximum strength compared to pure alginate scaffolds. Laden cells are homogeneously distributed throughout the alginate struts and the entire scaffold, resulting in cell viability of approximately 84%.     

Assessing the mechanical,phase inversion,and rheological properties of poly-[(R)-3-hydroxybutyrate-co-(R)-3-hydroxyvalerate] (PHBV) blended with poly-(l-lactic acid) (PLA)

Poly-(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and poly-(l-lactic acid) (PLA) have attracted much interest in recent years since they are biodegradable, thus can replace synthetic non-degradable materials. In this study, improvements of PHBV, mechanical, phase inversions, and rheological properties were investigated after blending with PLA in varying ratio’s. Three different blends of commercially available PLAs with 92–98% l-lactide units and one grade of PHB with 5% valerate content were blended using a micro-compounder at 175 °C. The composition of PHBV in blends ranged from 50% to 80%. With the addition of PLA, increases in the flexural strength and elastic modulus were observed for several blends, while minor to no changes were detected in the elongation at break and tensile strength as compared to pure PHBV material. Like many conventional plastics, the complex viscosity decreased with increasing rotational frequency due to decreasing entanglements and molecular weight. The complex viscosity with respect to time was very stable for the blends, but no improvements in the PHBV viscosity were observed with the addition of PLA at 170 °C. Three phase inversion models were used to predict the continuity of the blends, and the results showed both dual- and PLA-continuity phase for the blends. In summary, the mechanical results showed improvements in the tensile and flexural properties, while the rheological observation showed minor improvements in the complex viscosity for numerous concentrations.     

醋酸淀粉/聚乳酸的制备及性能的影响研究

采用自设计的双螺杆结构挤出制备聚乳酸(PLA)/醋酸淀粉(AS)的全生物降解材料,考察材料的AS的含量和取代度对复合材料动态流变性能、机械性能的影响。研究结果表明,AS含量明显影响复合材料的力学性能、复合黏度和储能模量:当AS含量从45%增加到70%,材料的拉伸强度下降,复数黏度和储能模量则提高。随着AS取代度由1.0上升为3.0,复合材料的复数黏度和储能模量下降,拉伸强度由12.0MPa上升为15.5MPa。对复合材料进行电镜扫描分析发现,AS以海岛结构形式分散在PLA的连续相中,取代度2.0的AS与PLA相容性最好,当其质量含量达到70%,材料的拉伸强度仍然不低于10.0MPa,具有较好的机械强度。