A Simple Thermal Decomposition Method for Synthesis of ZrO<Subscript>2</Subscript>/GrO Nanolayer

This paper reports on a novel processing route for producing ZrO₂/GrO nanocomposites by solid-state thermal decomposition of zirconium acetate nanostructures and graphene as starting reagents, powders were carried out in the temperature 200 °C for 2 h. In addition, nanocomposites of ZrO₂/GrO were obtained by solid-state thermal decomposition of the as-synthesized graphene oxide and Zr(CH₃COO)₂·4H₂O. The as-synthesized products were characterized by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy, atomic force microscope, photoluminescence spectroscopy and Thermogravimetric analysis. The sublimation process of the Zr(OAc)₂ and GrO powder were carried out within the range of 210, 220 and 230 °C. The XRD studies indicated the production of pure ZrO₂/GrO nanocomposites after thermal decomposition.     

溶剂热合成具有海绵状结构的介孔SnO2

采用溶剂热方法, 以SnCl4·5H2O/尿素/乙醇三元体系合成了具有特定结构的前驱体, 该前驱体经焙烧后得到了具有海绵状结构的介孔SnO2. 利用X射线粉末衍射(XRD)、傅立叶红外吸收光谱(FT-IR)、透射电镜(TEM)、热分析(TG-DTA)和氮气等温吸附鄄脱附等方法对产物的结构、形貌和热稳定性进行表征. 结果表明, 300 ℃焙烧处理后的样品由粒径约为5 nm的纳米粒子堆积而形成海绵状结构, 其中孔的尺寸范围在2-8 nm, 样品比表面积达到了134 m2·g-1.     

MeAPO-5分子筛的合成及其在肉桂醇选择氧化反应中的催化性能

采用水热法合成了一系列杂原子磷铝分子筛MeAPO-5(Me=Co,Fe,Cu,Zn,Mn),并利用X射线衍射(XRD),热重-差热分析(TG-DTA),电感耦合等离子体原子发射光谱(ICP-AES)和漫反射紫外-可见光谱(DRUV-Vis)等技术对分子筛的结构,化学组成以及金属离子的存在状态进行了表征.结果表明,合成的纯相MeAPO-5分子筛具有较高的结晶度,金属杂原子种类显著影响其在MeAPO-5分子筛中的存在状态,取代度及合成样品的结晶度.Co2+,Fe3+,Zn2+和Mn2+较易进入分子筛骨架,而Cu2+较难进入.通过考察MeAPO-5分子筛在肉桂醇氧化反应中的催化性能,发现CoAPO-5分子筛具有良好的选择氧化催化性能,1,4-二氧六环是较好的溶剂,调变反应温度可以有效调控产物的选择性.     

NiO亚微米球的制备及其光催化性质

在混合溶剂体系中,通过简单的二步方法成功合成了NiO亚微米球。第一步,以Ni(CH3COO)2和精氨酸为主要反应物,160℃溶剂热反应8 h制备出前驱体;第二步,煅烧前驱体成功合成了NiO产物。利用X射线粉末衍射(XRD),扫描电子显微镜(SEM),透射电子显微镜(TEM),热重分析(TGA)等手段对产物进行了表征。在紫外光照射下,研究不同光催化剂对甲基橙溶液降解效果。结果表明,NiO亚微米球在紫外光照射条件下对甲基橙溶液有光降解作用。     

自组装α-Fe2O3亚微米球的制备及其光催化性质

在乙二醇体系中, 通过简单的二步方法成功合成了α-Fe₂O₃亚微米球。第一步,以Fe(NO)₃和C₆H₁₂N₄为主要反应物160 ℃溶剂热反应8h制备出前驱体;第二步,煅烧前驱体成功合成了斜方相的α-Fe₂O₃产物。利用X射线粉末衍射(XRD),扫描电子显微镜(SEM),透射电子显微镜(TEM),红外吸收光谱(FTIR),能谱分析(EDS)和热重分析(TGA)等手段对产物进行了表征。在300 W紫外灯(主波长为365 nm)照射下降解一定浓度的甲基橙溶液,研究不同光催化剂对甲基橙溶液降解效果。由于制备产物的形貌和粒径影响其比表面积和对反应物的吸附能力以及带隙能,使得制备产物具有良好的光催化性能。结果表明,α-Fe₂O₃亚微米球在紫外光照射条件下对甲基橙溶液有光降解作用。     

The influence of the nanofiller on thermal properties of thermoplastic polyurethane elastomers

Pure Fe₃O₄ and Mn-doped Fe₃O₄ nanoparticles were synthesized by simple wet chemical reduction technique using nontoxic precursors. Manganese doping of two concentrations, 10 and 15%, were employed. All the three synthesized nanoparticles were characterized by stoichiometry, crystal structure, and surface morphology. Thermal studies on as-synthesized nanoparticles of pure ferrite (Fe₃O₄) and manganese (Mn) doped ferrites were carried out. The thermal analysis of the three as-synthesized nanoparticles was done by thermogravimetric (TG), differential thermogravimetric, and differential thermal analysis techniques. All the thermal analyses were done in nitrogen atmosphere in the temperature range of 308–1233 K. All the thermocurves were recorded for three heating rates of 10, 15, and 20 K min^?1. The TG curves showed three steps thermal decomposition for Fe₃O₄ and two steps thermal decompositions for Mn-doped Fe₃O₄ nanoparticles. The kinetic parameters of the three as-synthesized nanoparticles were evaluated from the thermocurves employing Kissinger–Akahira–Sunose (KAS) method. The thermocurves and evaluated kinetic parameters are discussed in this paper.     

饼干状二硫化钨纳米片的制备与结构表征

以钨粉、硫粉为原料,以K2HPO4为矿化剂,在500℃的密闭条件下,利用固相法合成了WS2纳米微粒;采用X射线衍射仪、扫描电子显微镜等表征了产物的结构,分析了矿化剂对WS2尺寸和形貌的影响.结果表明,当反应体系中存在适量的K2HPO4时,合成的WS2晶体呈饼干状,厚度约50nm,且结晶性良好.研究发现,在高温条件下,WS2晶粒在熔融K2HPO4中的形成和生长受到抑制,从而有利于其形貌和尺寸的控制.     

一种双钒帽多金属氧酸盐的水热合成及其晶体结构和热稳定性

采用水热法合成了一种双钒帽多金属氧酸盐[CrⅢ(1,10-phen)2(H2O)]2[PMoⅤ6MoⅥ6O40(VⅣO)2(OH)];利用元素分析、红外光谱、单晶X射线衍射表征了其组成和分子结构,利用热重分析测定了其热稳定性.结果表明,合成的化合物由无序的双帽假Keggin型[PMoⅤ6MoⅥ6O40(VⅣO)2(OH)]6-杂多阴离子和两个[CrⅢ(1,10-phen)2(H2O)]3+配位阳离子单元组成,其热失重分两步进行,热稳定性良好.     

Study of catalytic action of micro-particles and synthesized nanoparticles of CuS on cellulose pyrolysis

The catalytic action of copper sulfide (CuS) micro-particles and as-synthesized nanoparticles was studied on cellulose pyrolysis. The market procured CuS powder was used as micro-particles without any treatment. The CuS nanoparticles were synthesized at ambient temperature by simple wet chemical technique. Before using the micro-particles and nanoparticles for catalytic study, they were comprehensively characterized. The thermal analysis including catalytic properties of both the micro-particles and nanoparticles of CuS on cellulose pyrolysis was studied employing thermogravimetric (TG), differential thermogravimetric, and differential thermal analysis techniques. Prior to the study as catalyst in cellulose pyrolysis, the CuS micro- and nanoparticles were characterized by thermal analysis in inert atmosphere. The TG curves showed two steps and five steps decomposition having total mass loss of 29 and 42 % in case of CuS micro- and as-synthesized nanoparticles, respectively. The catalytic study in cellulose pyrolysis showed that the decomposition commences at temperature 295 °C for pure cellulose, 270 °C for cellulose mixed with 3 % CuS micro-particles and 205 °C for cellulose mixed with 3 % CuS nanoparticles. It clearly showed that the decomposition starting temperature decreased by 65 °C in case of cellulose mixed with CuS nanoparticles compared to cellulose mixed with CuS micro-particles. Thus, CuS nanoparticles act as better catalyst then CuS micro-particles in cellulose pyrolysis. The obtained results are deliberated in details.     

Low-temperature catalytic preparation of multi-wall MoS_2 nanotubes

Since the first report on inorganic fullerene-like WS2 polyhedra and nanotubes by Tenne et al.[1] in 1992, this kind of nanostructural materials have become extensive research topics owing to their unique electronic structures. WS2 and MoS2 nanomaterials have shown potential applications in the fields of scanning probe microscopy[2], solid-state lubrication[3], heterogeneous catalysis[4], and electrochemical hydrogen storage[5]. Up to now, a great deal of progress has been achieved in the st…     

Thermoanalytical investigation of the decomposition course of copper oxysalts

The thermal decomposition of copper nitrate trihydrate (CuNTH); Cu(NO₃)₂·3H₂O was studied up to 600°C by thermogravimetry (TG) and differential thermal analysis (DTA) in a dynamic atmosphere of air. The thermal events occurring throughout the decomposition course were characterized on the basis of spectral analyses using infrared spectroscopy (IR), X-ray diffractometry (XRD) and scanning electron microscopy (SEM). Non-isothermal kinetic parameters were determined. The results showed that the decomposition course involves two main processes, firstly the formation of hydroxy copper nitrate and secondly, the decomposition of this compound to yield CuO. Pathways were suggested that may be involved in the decomposition course.     

Thermal decomposition of polymeric aminoborane (H2BNH2)x under hydrogen release

Polymeric aminoborane (H₂BNH₂)_x has been isolated during the thermal decomposition of solid borazane H₃BNH₃ at temperatures below 370 K. Polymeric aminoborane is a white noncrystalline solid, stable at room temperature and up to 380 K. In the temperature range of 380–500 K polymeric aminoborane undergoes a thermal decomposition, which was studied by differential scanning calorimetry (DSC), by thermogravimetry (TG) and by volumetric measurements. The solid residue was characterized by IR spectroscopy, by powder X-ray diffraction (XRD) analysis and by solid state ¹¹B NMR spectroscopy.

The thermal decomposition of polymeric aminoborane (H₂BNH₂)_x is an exothermic process accompanied by evolution of nearly 1 mol hydrogen per mole H₂BNH₂ unit corresponding to the volumetric measurements. The detected mass loss of the solid phase indicates the formation of further gaseous products beside hydrogen. The final mass loss increases with rising heating rate, in contrast to the final amount of evolved hydrogen, which still remains constant.     

Template transformations in preparation of MCM-41 silica

Template transformation in MCM-41 material during thermal treatment under different conditions was investigated on the basis of thermogravimetry (TG-DTA), X-ray diffraction (XRD) and positron annihilation lifetime spectroscopy (PALS). Micelle templated silica was prepared using C18 trimethylammonium bromide. The pore structure of MCM-41 samples obtained after removal of the surfactant in air, argon flow and vacuum was analyzed on the basis of the adsorption isotherms of nitrogen at 77 K and XRD experiments. The TG-DTA experiments confirm the mechanism of the template removal known from literature. However, the sequence of the processes during thermal treatment of as-synthesized sample and temperature of transformations depended strongly on the presence of oxygen and the heating rate. The main template degradation took place below 573 K and was independent of the kind of atmosphere above the sample. Residual carbonaceous species are removed from pores and the external surface of MCM-41 silica upon heating to 823 K by combustion or evaporation. The latter process as well as translocation of liquid-like products of template degradation from the pore interior to external surface was confirmed by PALS experiment in vacuum.     

[Cu2(C2O4)(C12H8N2)2(C3H7NO)2](ClO4)2配合物的合成及其热分解

以邻菲罗啉、2,5二羟基-1,4-二噻烷和Cu(ClO4)2.6H2O为原料,合成了中心对称的双核配合物[Cu2(C2O4)(C12H,N2)2(C3 H7NO)2](ClO4)2(1).通过红外光谱、元素分析等分析测试手段对其进行了表征;借助TG-DTG技术在氮气气氛下研究了配合物的热分解情况,并根据热分析结果确定了...     

Thermal decomposition of [bis(salicylaldehydato)cadmium(II)] to CdS nanocrystals

The present investigation reports, the novel synthesis of nanocrystals CdS using thermal decomposition of [bis(salicylaldehydato)cadmium(II)], as a new precursor, and elemental sulfur in oleylamine. The as-synthesized CdS crystals have diameters about 10 nm. The products were characterized by X-ray diffraction (XRD) transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), ultraviolet–visible (UV–Vis) spectroscopy and Fourier transformed infrared (FT-IR) spectra. The results of this paper show that the shape and size of cadmium sulfide nanocrystals can be controlled systematically by adjusting certain reaction parameters, such as the reactant concentration, the reaction temperature and the reaction time. Cadmium sulfide nanoparticles and nanorods with different lengths have been successfully prepared.     

Iron-containing nanocomposites based on mesoporous aluminosilicates

Here we report the synthesis and magnetic characterization of iron-containing nanocomposites based on mesoporous aluminosilicates (MAS). MAS with Al:Si ratio equal to 1:15 was synthesized by a two-step hydrothermal treatment. The chemical composition and structure of the matrix were determined by chemical analysis, TGA, SAXS and adsorption of nitrogen at 77 K. The intercalation of iron into the channels was performed either by cationic exchange or by soaking the initial matrix in Fe(CO)₅. Reduction/decomposition of the complex was carried out by thermal treatment in a hydrogen flow. The nanocomposites obtained were characterized by XRD, TEM, Mössbauer spectroscopy and magnetic measurements. It was shown that the first method does not give any magnetic phases at nanolevel. The second method results in the formation of magnetic iron-containing nanowires (with diameter <2 nm and length over 30 nm) in a mesoporous matrix, which possess blocking temperatures over 300 K and coercivity up to 31,000 A/m at room temperature.     

Synthesis, crystal structure and thermal decomposition of a new copper propionate [Cu(CH3CH2COO)2]·2H2O

A new copper propionate complex was synthesised and characterized for application as precursor for CuO based oxide thin films deposition. The FT-IR and X-ray diffraction analyses have revealed the formation of a cooper propionate complex [Cu(CH₃CH₂COO)₂]·2H₂O. The crystal and molecular structure of a new copper propionate complex was determined by XRD on the copper propionate single crystal. The copper propionate complex has a binuclear structure, connected by bridging bidentate carboxylates groups and a Cu?Cu bond of 2.6 Å. The thermal decomposition of copper propionate has been investigated by thermal analysis using thermogravimetric (TG) and differential thermal analysis (DTA), differential thermal analysis coupled with quadrupole mass spectrometry-QMS, X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FT-IR) techniques. TG and XRD data indicate the reduction of Cu(II)-Cu(I,0) during the decomposition of copper propionate.     

Thermal and photoluminescence properties of hydrated YPO4:Eu nanowires

In this work, we used the solution precipitation route to synthesize Eu³⁺-doped YPO₄·nH₂O nanowires. The structure, morphology, composition, thermal behavior, and photoluminescence of as-synthesized product were characterized by X-ray diffraction (XRD), thermogravimetric and differential thermal analysis (TG/DTA), energy-dispersive X-ray spectroscopy (EDS), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopic (FE-SEM) and photoluminescence (PL) spectra. The dependence of the structure, morphology, composition and luminescent properties on the thermal treatment was investigated. The results indicate that the aqueous synthesis has a better control on the structure, morphology, composition of the products, and that the heat treatment induces the transitions of the structure, composition, and luminescent properties.     

Thermal decomposition of manganese(II)bis(oxalato)nickelate(II)tetrahydrate

Summary A mixed metal oxalate, manganese(II)bis(oxalato)nickelate(II)tetrahydrate, has been synthesized and characterized by elemental analysis, IR spectral and X-ray powder diffraction (XRD) studies. Thermal decomposition studies (TG, DTG and DTA) in air showed that the compound decomposed mainly to Mn₂O₃, MnO₂ and NiO at ca.1000°C, via. the formation of several intermediates. DSC study in nitrogen upto 500°C showed the endothermic decomposition. The tentative mechanism for the thermal decomposition in air is proposed.     

Synthesis and Characterization of Magnesium Substituted Aluminophosphate Molecular Sieves with AEL Structure

MAPO-11 molecular sieves were synthesized by hydrothermal methods. The influence of precursor of magnesium, Mg/Al ratio, synthesis temperature, synthesis time and the type of template on the formation and properties of MAPO-11 molecular sieves was examined. The samples were characterized by the techniques of X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric/differential thermogravimetric analysis (TG-DGA), etc. The results show that the shape and size of crystal were influenced by the precursor of Mg, the Mg/Al ratio and the type of template, and the TG-DGA analysis shows that MAPO-11 molecular sieves as-synthesized have poor thermal stability.