端面抽运Tm,Ho:YLF激光器热转换系数及热透镜效应的研究

根据激光二极管纵向抽运Tm,Ho:YLF激光器的能级跃迁和能量传递过程，在考虑能量传递上转换和基态重吸收的前提下，建立了准三能级速率方程理论模型.给出了Tm,Ho:YLF激光器的热转换系数的解析表达式，讨论了抽运光斑半径与激光束腰半径的比值对热转换系数的影响.实验上得到了热焦距随抽运功率的变化关系，并将其与理论结果进行了对比，发现符合较好. 关键词： Tm Ho:YLF晶体 能量传递上转换 速率方程 热转换系数     

The influence of energy transfer upconversion on thermal loading in end-pumped Nd:GdVO4 laser

The influence of energy transfer upconversion on thermal loading in end-pumped Nd:GdVO₄ laser was investigated. The dependence of thermal loading on absorbed pump power and pump radius was discussed. Higher absorbed pump power and smaller pump radius resulted in more serious ETU effect, which cause more extra thermal loading. The experimental results indicated that ETU effect in Nd:GdVO₄ laser is a unneglectable mechanism to generate extra heat especially in end-pumped geometry     

Tomographic reconstruction of 2D-OH<Superscript>∗</Superscript>-chemiluminescence distributions in turbulent diffusion flames

A theoretical model on actively Q-switched Nd³⁺-doped quasi-three-level laser including the energy transfer upconversion and the ground state reabsorption is developed. The analytical expressions of the fractional thermal loading and the average output power are obtained, and the influence of ETU effects on laser performance for different repetition rate is analyzed. The average output power and the thermal focal length of the Q-switched 946 nm laser are acquired in experiment. The good agreement between the experimental data and theoretical results demonstrates the reliability of the theoretical model.     

Influences of pump beam distribution on thermal lensing spherical aberration in an LD end-pumped Nd:YAG laser

A numerical investigation is made on the thermal lensing and spherical aberration effect in an LD end-pumped Nd:YAG laser. Based on the finite element method (FEM), the laser rod temperature distribution is calculated and the focal length of the thermal lens is deduced, the influences of pump beam on the thermal lensing spherical aberration are mainly studied. The results show the thermal lens which focal length varied with the radial coordinate r is not an ideal lens. Given the heat dissipation boundary conditions, the radial dependent focal length will be shortened when the pump power raised or the waist radius of the pump beam reduced, meanwhile the radial differences of the focal length will decrease when the pump power increased. For a Super-Gaussian profile pump beam, the higher the exponent number, the more similar to flat top the pump beam is, and the less the radial differences of the focal length are.     

薄片激光器热效应及其对输出功率的影响

建立了光强分布为高斯型的抽运光端面单程抽运时薄片激光器的温度模型, 实验测量了不同抽运功率下薄片介质表面的 温度分布、温度随时间的变化特性以及介质表面的温度差. 采用Hartmann法测量了薄片介质的热焦距. 考虑热焦距随抽运功率的变化, 基于四能级系统薄片激光器的速率方程组, 建立了薄片激光器热效应对输出功率影响的物理模型, 薄片激光器输入-输出功率曲线与实际相符. 所得结果对薄片激光器的设计和优化具有一定的指导意义.     

Thermal focal length measurement of an LD-end-pumped Tm,Ho:GdVO4 laser

The thermal focal length of a Tm,Ho:GdVO₄ crystal was measured in this paper. The pump laser was 25.73 W, and the thermal focal length was 692.6 mm; based on the thermal focal length of a Tm,Ho:GdVO₄ crystal, a single end-pump continuous wave (CW) operation of Tm,Ho:GdVO₄ laser was designed to demonstrate the effect of thermal focal length, and a 0.26-W output power was high in considering the thermal focal length than in unconsidering the thermal focal length with a 26.1-W pump power.     

基于侧面热对流的LD泵浦Yb:KGd(WO4)2热透镜效应研究

基于对LD端面泵浦Yb∶KGW激光晶体工作特点的分析,建立了符合条件的激光晶体热模型.考虑晶体侧面的热对流,运用MATLAB和FORTRAN软件,通过有限差分法求解各向异性介质热传导方程,得到了该晶体的温度场分布、端面热形变分布和不同泵浦功率下的热焦距.结果表明:在泵浦功率为14 W时,泵浦面最高温度达272.8℃、最...     

平顶光端面抽运DPL中热效应对输出功率的影响

用平顶光束描述由多根光纤紧密排列耦合并经透镜整形后的抽运光分布，给出了平顶光束的光强分布，对晶体热效应引起的热致衍射损耗随抽运功率和抽运光束半径的变化规律进行了数值计算，讨论了晶体热效应引起的热致衍射损耗对基横模高斯光束输出功率的影响，并实验验证了基横模高斯光束输出功率随抽运功率的变化规律．结果表明：热致衍射损耗使基横模高斯光束输出功率明显降低．随着抽运光束半径的增大，热致衍射损耗减小，对基横模高斯光束输出功率的影响就减小；抽运功率越大，热致衍射损耗越大，对基横模高斯光束输出功率的影响就越大．     

The overall phase shift and lens effect calculation using Gaussian boundary conditions and paraxial ray approximation for an end-pumped solid-state laser

In this work, the inhomogeneous equation of heat conduction was exactly solved by applying inhomogeneous boundary conditions for laser crystals of aspect ratio=1 (aspect ratio=radius of the laser rod/length of the laser rod). We have shown that the paraxial ray approximation leads the solution to be a function ofr ² , that is, the approximation is equivalent to a situation in which a homogeneous pump source is used. The solution was then used to derive expressions for the overall phase shift, focal length of the thermal lens and the end effect induced curvature of the end face. The expressions were then applied to Nd:YAG laser medium. The result shows a meaningful correction of the order of 0.001 cm to the focal length of Nd:YAG rod for 3 W source power and beam waist of 100 μm.     

LD端面抽运Nd∶KGW 激光器热效应的理论与实验研究

对LD端面泵浦Nd∶KGW激光器的热效应进行了分析.求解热传导方程得出了Nd∶KGW晶体的温度分布和端面形变,进而计算出了热焦距随泵浦功率的变化曲线,并通过实验对其正确性进行了验证.采用凹 平腔,在不同透过率的输出镜下,对Nd∶KGW晶体的1 064 nm连续激光输出特性进行了研究.     

端侧面组合抽运DPL热透镜效应研究

通过数值计算发现：在端侧面组合抽运DPL中,晶体横截面上的温度分布接近于轴对称分布,并且端面抽运功率占有率越大,温度分布越接近于轴对称分布。将端侧面组合抽运DPL中的热效用等效薄透镜近似,给出了等效热透镜焦距的计算方法,分析了组合抽运引起的热透镜效应对基横模振荡光的光斑尺寸和衍射损耗的影响。在总抽运功率一定的情况下,端面抽运功率占有率的变化对热透镜焦距有一定的影响,占有率越大,热透镜焦距越长。提高端面抽运功率占有率,可在一定程度上减小热透镜效应对振荡光束尺寸和衍射损耗的影响。     

Stationary generation of diode-pumped self-Raman Nd:YVO<Subscript>4</Subscript>/YVO<Subscript>4</Subscript> composite crystal laser

Output power dependences of composite Nd³⁺:YVO₄ Raman laser stationary generation on the longitudinal diode pump power are measured at different transmissions of the output mirror at the Stokes radiation frequency. The deviation of the measured dependences from linear is explained by the influence of thermal effects on both the overlap of the beams and diffraction losses. A method to estimate the laser and Stokes losses in the cavity and the parameters characterizing the overlap of the laser radiation with the pump and Stokes beams is proposed. A Stokes-component of power 2.1 W is obtained and corresponds to 12% diode-to-Stokes efficiency.     

低功率激光热透镜效应的模拟及研究

与高功率激光相比,低功率激光更安全,其热透镜效应对激光功率变化更敏感,更适合用于实验教学.本文利用有限元法模拟低功率激光的热透镜效应,模拟介质温度场和等效热透镜焦距,定量探究低功率激光热透镜焦距与激光功率以及介质热吸收率、厚度的关系.模拟结果与实验数据符合良好,为探究低功率激光热透镜效应实验提供理论依据.     

High-power diode-end-pumped CW Nd:GdVO4 laser

We report on a high-power diode-end-pumped CW Nd:GdVO₄ laser. Under the pump power of 39.5 W, a maximum output power of 19.8 W and a slope efficiency of 58.5% were obtained. The beam quality M² at maximum output power was measured to be around 2.62. The thermal focal length in Nd:GdVO₄ crystal under the pump power from 22 to 40.6 W was measured. The pump-induced damage threshold was estimated to be 28.6 kW/cm².     

Thermal lens measurement technique in end-pumped solid state lasers: Application to diode-pumped microchip lasers

A simple derivation, which relates the thermal lens focal length in solid state lasers to pump power and a method for direct estimation of thermal lens focal length, is reported. This method is applicable to any type of stable resonator. The method is used for the measurement of the thermal lens focal length with an accuracy of 8% in an axially pumped microchip laser. The variation of focal length with pump power is also measured.     

Experimental determination of effective stimulated emission cross-section in a diode pumped Nd:YVO4 micro-laser at 1064 nm with various doping concentrations

A practical method is described and used for determination of the effective stimulated emission cross-section (σ_e) in an operating diode pumped Nd:YVO₄ micro-laser at 1064 nm with various doping concentrations. In this method a micro-laser is formed by keeping a small piece of the sample in a plane–plane resonator under semi-monolithic configuration and a fiber coupled diode laser (808 nm) was used for pumping. The pump power induced thermal lensing effect was used to make the cavity stable. In thermally stabilized solid-state lasers the cavity parameters change dynamically with the pump power and hence the overlap integrals become a function of the absorbed pump power. In our method the overlap integrals were estimated by measuring the thermal lens focal length at the threshold. The value of σ_e of Nd:YVO₄ crystal with different doping concentrations obtained by this method were in well agreement with the reported values.     

Design of a 2.5 THz submillimeter wave laser with optical pump beam guiding

A ring resonator design using the same set of mirrors for pump beam and submillimeter wave (SMMW) beam guiding is introduced. Optimal design is discussed on the example of a 2.5 THz methanol laser. It turns out that due to refocussing of the pump beam on the pinhole certain focal lengths of the focussing mirror, which mainly is responsible for the beam guiding, should be avoided. Diffraction losses and pinhole losses determine optimalg-parameters for which the pump beam guiding losses of the resonator are minimum, and optimal pump beam waist radii.The setup of an experimental laser with the optimized resonator and the experimental setup to measure laser performance are described, and results concerning laser output power, beam quality and efficiency are discussed.     

Determination of the thermal loading of diode-pumped Nd:YVO(4) by use of thermally induced second-harmonic output depolarization

A new method of using thermally induced second-harmonic output depolarization to determine the fractional thermal loading of a diode-pumped Nd:YVO(4) laser is proposed. The experimental results show that the fraction of the green output power polarized along the extraordinary axis of a KTP crystal, f(e) , is an oscillatory function of the absorbed pump power. The fractional thermal loading can be determined by measurement of the difference in the absorbed pump power between the peaks of f(e) .     

纵向泵浦固体激光介质热透镜效应的理论研究

 在分析了纵向泵浦、周边致冷固体激光棒内加热及冷却机理的基础上,将热传导方程合理简化为一维形式,求解出以级数方式表达的棒内温度分布。并根据热弹性力学原理,获得了激光棒中热致应力场和应变场。在考虑了与热透镜效应有关的三个因素：即热色散、热致应力双折射和端面变形后,推导出了纵向泵浦固体激光棒有效热焦距的解析表达式。将所获结果运用于常用的激光晶体Nd:YAG,发现当使用10W半导体激光器泵浦时,所产生的有效热焦距在毫米量级。     

10 kHz 40 W Ti:sapphire regenerative ring amplifier

A cryogenically cooled Ti:sapphire regenerative ring amplifier was developed as a laser for generating a laser-produced plasma light source. With a 10 kHz 180 W pump laser, the amplifier output is 40 W before compression and 26 W after compression. We believe it to be the current highest average-power output from a single stage Ti:sapphire amplifier. The effective focal length of the thermal lens is measured to be 2.2 m at 100 K for 180 W of pump power. With a 1 m focal length lens placed in the resonator, the effect of a thermal lens on the resonator mode is suppressed. High conversion efficiency is achieved for the whole pumping power range without any additional measures for thermal compensation.