大气压下绝缘毛细管内等离子体放电及其特性研究

在石英毛细管内利用两个边缘锋利的中空针型电极间的放电形成了63 cm长的大气压弧光等离子体.通过记录放电图片和测量电流-电压特征波形及伏安特性曲线的方法对管内等离子体从反常辉光状态过渡至超长弧光状态的过程做了细致的研究,发现管内等离子体在弧光状态下的电子密度不低于10¹⁴ cm^-3.另外,还进一步考察了两电极的间距和电源工作频率对放电伏安特性的影响以及通过发射光谱法测得的等离子体气体温度随外加电压的变化规律.当活性气体(氧气)按一定比例混合到氩等离子体中时,通过 关键词： 大气压等离子体 反常辉光放电 弧光放电 发射光谱     

沿面放电中的辉光和赝辉光放电

利用沿面放电发生器装置，在流动氩气中实现了大气压辉光放电。放电电流波形表现为外加电压每半周期只有一个电流脉冲。驱动电压频率是60kHz时，放电电流脉冲持续时间大于1微秒。氩气中的辉光放电，功率消耗随着外加电压增加或者是气压减小而增大，这种关系可以用汤生击穿理论定性解释。与此对比，大气压空气中的放电电流波形为外加电压每半周期放电为许多脉冲，每个电流脉冲为高频阻尼振荡，这就是赝辉光放电。大气压空气中的赝辉光放电可能是由于气体的流光击穿造成的。     

On the increase in the limiting current of an atmospheric-pressure glow discharge in an argon flow

The initiation of an atmospheric-pressure glow discharge (APGD) is studied in the multitip cathode-planar anode electrode system through which an argon flow passes. It is shown that sectioning of the cathode and ballast resistances present at corona tips make it possible to substantially expand the current region of the discharge and considerably raise the limiting current of the APGD. The shape of the coronafree electrode is found to influence the limiting discharge current.     

Characteristics of a high-frequency barrier discharge in mixtures of mercury diiodide vapor with gases

The spectral and electric characteristics of atmospheric-pressure high-frequency barrier discharge plasma based on mixtures of mercury diiodide with neon and admixtures of argon, xenon, and nitrogen are analyzed. A repetition rate of sinusoidal voltage pulses of about 100 kHz is used both to produce the gas discharge plasma and to excite the components of the working mixture. The radiation of the discharge in the range 200–900 nm is analyzed with a high resolution. It is found that, in the range 400–900 nm, the system of bands of excimer molecules HgI(B → X) emits 85% of the barrier discharge radiation. It is established that the radiation intensity of HgI(B → X) molecules is maximal in the mixture HgI₂/Xe/Ne = 0.6/10/90 kPa. In this mixture, UV radiation of molecules XeI(B → X) and XeI(B → A) is observed. The regular features of the spectral and electric characteristics of the gas discharge plasma are discussed. An atmospheric-pressure high-frequency barrier discharge in mixtures of mercury diiodide with gases is of interest for use in a selective (Δλ = 438–446 nm) excilamp with a cylindrical working aperture.     

Glow discharge cleaning of vacuum switch tubes

To clean the surfaces of parts inside a vacuum-switch tube (VST) the authors propose a technique which generates a glow discharge between the inner electrodes and the copper grid surrounding it. Photographic observation reveals that the glow discharge spreads out and cleans the whole surface inside the VST. A breakdown test between the inner electrodes shows the effect of the cleaning with this technique. Higher breakdown voltage between the inner electrodes is attained by performing this glow discharge cleaning in argon rather than hydrogen gas. The difference of the cleaning effect seems to be attributed to that of the energy transfer from ion species to the adsorbed molecules and microprotrusions on the surfaces     

Generation of uniform atmospheric pressure argon glow plasma by dielectric barrier discharge

In this paper, atmospheric pressure glow discharges (APGD) in argon generated in parallel plate dielectric barrier discharge system is investigated by means of electrical and optical measurements. Using a high voltage (0–20 kV) power supply operating at 10–30 kHz, homogeneous and steady APGD has been observed between the electrodes with gap spacing from 0.5 mm to 2 mm and with a dielectric barrier of thickness 2 mm while argon gas is fed at a controlled flow rate of 1 l/min. The electron temperature and electron density of the plasma are determined by means of optical emission spectroscopy. Our results show that the electron density of the discharge obtained is of the order of 10¹⁶ cm^???3 while the electron temperature is estimated to be 0.65 eV. The important result is that electron density determined from the line intensity ratio method and stark broadening method are in very good agreement. The Lissajous figure is used to estimate the energy deposited to the glow discharge. It is found that the energy deposited to the discharge is in the range of 20 to 25 μJ with a discharge voltage of 1.85 kV. The energy deposited to the discharge is observed to be higher at smaller gas spacing. The glow discharge plasma is tested to be effective in reducing the hydrophobicity of polyethylene film significantly.     

Electron impact ionization and excitation rate coefficients in the negative glow region of a glow discharge

Some easy to use reasonable approximations for electron impact rate coefficients have been considered. The most important rate coefficients for electron collisions in noble gases are electron-neutral ionization and electron impact excitation. Electron-neutral ionization besides electron impact excitation of some states of the argon and helium atom in direct current (dc) glow discharge plasma has been calculated. The plasma parameters of electron are significant factors for computing the rate coefficients. We present first results of probe diagnostic that includes the double probe measurements of the plasma parameters, namely, electron temperature (T_e) and electron density (n_e). Electron properties obtained from the double probe characteristic curves including T_e and n_e as well as the calculated rate coefficients (ionization and excitation) were studied as a function of the axial distance from the cathode while the discharge operating parameters of voltage and pressure were varied. Two regions of the glow discharge were investigated: cathode fall region and negative glow. Particular emphasis was placed on the negative glow region.     

实验研究大气压多脉冲辉光放电的模式和机理

采用稍不平行电极进行大气压He气介质阻挡多脉冲辉光放电实验,通过增强电子耦合器件相机短时曝光照片,研究大气压多脉冲辉光放电在不同时刻的放电模式.通过气隙放电电流、表面电荷计算,理论分析了表面电荷、空间电荷、外加电压与气隙电场强度的关系,研究大气压辉光放电形成多脉冲的机理.实验结果表明,放电首先在间隙稍窄的电极左端开始;在第一个脉冲电流峰值,电极右端也开始放电;第一个电流脉冲经历了Townsend放电到辉光放电的过程;电流脉冲之间的时间内,间隙一直维持着微弱的辉光放电;随后的每个电流脉冲均是辉光放电.理论分析表明,大气压辉光放电的多个电流脉冲是表面电荷、空间电荷与外加电压共同演化的结果;除放电伊始出现Townsend放电外,同一半周期内的放电电流脉冲中不会再出现Townsend放电. 关键词： 介质阻挡放电 增强电子耦合器件 大气压辉光放电 多脉冲     

实验研究大气压多脉冲辉光放电的模式和机理

采用稍不平行电极进行大气压He气介质阻挡多脉冲辉光放电实验,通过增强电子耦合器件相机短时曝光照片,研究大气压多脉冲辉光放电在不同时刻的放电模式.通过气隙放电电流、表面电荷计算,理论分析了表面电荷、空间电荷、外加电压与气隙电场强度的关系,研究大气压辉光放电形成多脉冲的机理.实验结果表明,放电首先在间隙稍窄的电极左端开始;在第一个脉冲电流峰值,电极右端也开始放电;第一个电流脉冲经历了Townsend放电到辉光放电的过程;电流脉冲之间的时间内,间隙一直维持着微弱的辉光放电;随后的每个电流脉冲均是辉光放电.理论分析表明,大气压辉光放电的多个电流脉冲是表面电荷、空间电荷与外加电压共同演化的结果;除放电伊始出现Townsend放电外,同一半周期内的放电电流脉冲中不会再出现Townsend放电.     

Some Investigations of the Ignition and Development of Breakdown in Cylindrical Hollow Cathode Glow Discharges

The breakdown behaviour of a hollow cathode glow discharge is investigated in a cylindrical, hollow cathode structure having an internal diameter of 2 cm. The anode is a plane electrode across one end of the cathode cylinder. Pressures of argon between 20 and 107 Pa were used (0.15 to 0.80 torr), and applied voltages between 800 and 2500 V. It is shown that the statistical time lag for breakdown is in the range of ～ 1 ms and depends on the applied voltage, the gas pressure, and the history of operation of the discharge tube. The rise time of the discharge current ranges from about 10 ns at high pressure and voltage to about 200 ns at the lowest pressure and voltage used. The discharge propagates along the cathode axis at a speed of about 10⁸ cm s^?1. From the obtained data, a qualitative model of the first stage of the discharge is derived. Based on this model, a simple calculation gives values of Townsend modified first coefficient η at high values of E/N, 10⁴ < E/N < 8 · 10⁴ Td which fit well at the lowest E/N, where they approach the data of PENNING and KRUITHOF in argon. In contrast to the extremely short initial current-rise times, in the submicrosecond range, the discharge currents reach steady-state values only after about 300 μs.     

The effect of external visible light on the breakdown voltage of a long discharge tube

The breakdown characteristics of a discharge tube with a configuration typical of gas-discharge light sources and electric-discharge lasers (a so-called “long discharge tube”) filled with argon or helium at a pressure of 1 Torr have been investigated. A breakdown has been implemented using positive and negative voltage pulses with a linear leading edge having a slope dU/dt ~ 10–10⁷ V/s. Visible light from an external source (halogen incandescent lamp) is found to affect the breakdown characteristics. The dependences of the dynamic breakdown voltage of the tube on dU/dt and on the incident light intensity are measured. The breakdown voltage is found to decrease under irradiation of the high-voltage anode of the tube in a wide range of dU/dt. A dependence of the effect magnitude on the light intensity and spectrum is obtained. Possible physical mechanisms of this phenomenon are discussed.     

X-ray radiation due to nanosecond volume discharges in air under atmospheric pressure

The formation of nanosecond discharges in atmospheric-pressure air versus the applied pulse polarity and discharge gap geometry is studied. It is shown that the polarity of high-voltage nanosecond pulses and the electrode configuration have a minor effect on the volume discharges under a variety of experimental conditions. When the spacing between needle-like electrodes is large, the discharge is asymmetric and its glow is weakly dependent on the sign of the potential applied to the electrode. Negative voltage pulses applied to the potential electrode generate X-ray radiation from both the surface and volume. For a subnanosecond rise time of the voltage pulse and diffusion character of the discharge, the X-ray radiation comes from the brightly glowing region of a corona discharge. The average values of the fast electron velocity and energy in nitrogen are calculated. At field strengths E/p < 170 kV/cm atm, the average velocity of a fast electron bunch is constant because of central collisions. At field strengths E/p > 170 kV/cm atm, fast electrons run away. Central collisions are the reason for X-ray radiation from the volume.     

Heat transfer between tungsten surface and glow discharge plasmas in argon and CO<Subscript>2</Subscript>

A hot-filament method is used to study the heat transfer between tungsten surface and hollow-cathode glow discharge plasmas in argon and CO₂. The dependence of the electric power supplied to a tungsten wire on the discharge current is determined for argon and carbon dioxide in the temperature range between 1000 and 1700 K. A difference in heat transfer at the tungsten wire surface is found between experiments on argon and carbon dioxide. The difference is attributed to heterogeneous recombination in CO₂ plasma.     

Characteristics of DC discharge in a wire-cylinder configuration at high ambient temperatures

In the present work, the characteristics of direct-current (DC) discharge in a wire-cylinder configuration at an ambient temperature range of 350–850 °C were studied by analyzing photographs of the discharging process and the corresponding V–I characteristics, with the aim of facilitating the application of plasma technology in the fields of energy and the environment. The influences of the ambient temperature, the inter-electrode gap, the gas medium and the cathode material on the DC discharge were investigated. The corona-onset threshold voltage (COTV) and the spark-breakdown threshold voltage (SBTV) decrease as the ambient temperature increases, and the SBTV decreases more rapidly. Increasing the inter-electrode gap enlarges the difference between the SBTV and the COTV. After spark breakdown, in an air atmosphere, glow discharge is more likely to take place under conditions of high ambient temperatures or small inter-electrode gaps. The values of the SBTV in different atmospheres have the following relation: air ≈ O₂ > CO₂. At an ambient temperature range of 350–850 °C and in an atmosphere of N₂, glow discharge and arc discharge occur successively as the output voltage of the power supply is increased, while in an atmosphere of O₂ and CO₂, only corona and arc discharge are successively observed. In an air atmosphere, when the inter-electrode gap is 29 mm, corona, glow and arc discharge occur successively with increasing output voltage when the ambient temperature is 850 °C, while only corona and arc discharge appear when the temperature is 350–750 °C. When the inter-electrode gap is 5 mm in an air atmosphere, corona, glow and arc discharge occur successively in an ambient temperature range of 350–850 °C. The cathode material has a minor influence on the COTV and a more significant influence on the SBTV. In a device using a cathode with a low work function, the SBTV is low, and the power to maintain arc discharge is small.     

Pulsed discharge in nitrogen and argon under an elevated pressure in a nonuniform electric field

The characteristics of a discharge and radiation in nitrogen and argon under pressures of 10–760 Torr and the discharge formation without pre-ionization of the gap from an auxiliary source are considered. A peak is detected on the pressure dependence of the radiation power of the second positive system of nitrogen for E ₀/p ～ 270 V/cm Torr and nitrogen pressure p ～ 70 Torr. In the pressure range 10–760 Torr and for a voltage pulse leading front duration of ～ 10 ns, an electron beam is formed behind the grid anode with various half-amplitude pulse durations. It is shown that, under the given conditions, the electron beam is formed at the voltage pulse front both in the case of a discharge gap breakdown and in the absence of a clearly manifested breakdown, as well as for a 10-ns delay of breakdown at the leading front of a discharge current pulse.     

人工神经网络方法预测八面体六卤化物MX~(n-)_6的ν_1和ν_2模的振动频率

利用ＡＮＮ－ＢＰ算法，采用逐步改变训练步长和两个惯性项的权重系数惯性调整策略，分别以单目标和双目标的三层网络对八面体六卤化物ＭＸｎ－６的八面体ν１和ν２模振动频率进行了预测，发现单、双目标下预测的结果相差不大，双目标时权重系数调整得较快，［ＭｏＦ６］２－，［ＢｉＦ６］－和［ＡｕＦ６］２－的振动频率文献值与网络的计算值或预测值相差偏大。     

Self-Organization and Migration of Dielectric Barrier Discharge Filaments in Argon Gas Flow

Observations of atmospheric-pressure dielectric barrier discharge are conducted through a water-filled electrode in atmospheric-pressure argon gas flow. Quasi-symmetric self-organized discharge filaments were observed. The streamers moved with the gas flow, and the migration velocity increased with increasing gas velocity.     

Two-Photon Laser-Induced Fluorescence Spectra of Argon in a Grimm-Style Glow Discharge Tube

Two-photon excited laser-induced fluorescence (LIF) spectra of argon atom were successfully observed in a Grimm-style glow discharge tube, which has widely been applied to depth profiling of the elemental composition on various film-like samples by emission spectrometry. The LIF signal of an argon atomic line at 641.63 nm was observed when the glow discharge argon plasma was illuminated by a pulsed Ti:sapphire laser radiation of 7–10 mJ/pulse at 753.39 or 795.66 nm without focusing of the laser beam.     

介质阻挡放电点燃大气压直流均匀放电的光谱研究

由于大气压均匀放电等离子体在工业领域具有广泛的应用前景,为了获得大尺寸的大气压均匀等离子体,采用氩气作为工作气体,在大气压空气环境中利用同轴介质阻挡放电点燃了针-板电极间的大气隙(气隙宽度达到5 cm)直流均匀放电。研究发现,同轴介质阻挡放电能够有效降低针-板电极间的击穿电压。该均匀放电由等离子体柱、等离子体羽、阴极暗区和阴极辉区组成。其中等离子体柱和阴极辉区都是连续放电。而等离子体羽不同位置的放电是不同时的。事实上,等离子体羽放电是由从阴极向着等离子体柱移动的发光光层(即等离子体子弹)叠加而成。利用电学方法测量了放电的伏安特性曲线,发现其与低气压正常辉光放电类似,均具有负斜率。采集了放电的发射光谱,发现存在N₂第二正带系、氩原子和氧原子谱线。通过Boltzmann plot方法对放电等离子体电子激发温度进行了空间分辨测量,发现等离子体柱的电子激发温度比等离子体羽的电子激发温度低。通过分析放电机制,对以上现象进行了定性解释。这些研究结果对大气压均匀放电等离子体源的研制和工业应用具有重要意义。     

Characteristics of a glow discharge in atmospheric pressure air over the water surface

The current-voltage characteristics, the amount of cathode fall, and the spectra of plasma radiation from different spatial domains are presented versus the molecular band intensity of products arising in an atmospheric-pressure air glow discharge over the distilled water surface. The plasma electron temperature is also reported. The distance to a liquid cathode or anode is varied from 1 to 10 mm at a discharge mean current of 10–36 mA.