Charge compensation and oxidation in NaxCoO2−δ and LixCoO2−δ studied by XANES

A comparative study on the oxidation and charge compensation in the A_xCoO_2−δ systems, A=Na (x=0.75, 0.47, 0.36, 0.12) and Li (x=1, 0.49, 0.05), using X-ray absorption spectroscopy at O 1s and Co 2p edges is reported. Both the O 1s and Co 2p XANES results show that upon removal of alkali metal from A_xCoO_2−δ the valence of cobalt increases more in Li_xCoO_2−δ than in Na_xCoO_2−δ. In addition, the data of O 1s XANES indicate that charge compensation by oxygen is more pronounced in Na_xCoO_2−δ than in Li_xCoO_2−δ.     

Fabrication and optical conductivities of strained epitaxial NaxCoO2 thin films: x=0.5, 0.7

Epitaxial γ phase-Na_xCoO₂ thin films were deposited on (001) sapphire by the pulsed laser deposition method. To fabricate epitaxial Na_0.5CoO₂ thin films, we used a solution of iodine-dissolved acetonitrile and obtained an epitaxial Na_0.5CoO₂ thin film with a high crystallinity because of Na deintercalation of epitaxial Na_0.7CoO₂. From the spectroscopic ellipsometry analysis, we obtained the optical constants as well as the optical conductivities for the Na_0.5CoO₂ and Na_0.7CoO₂ thin films. The energy splitting between e_g and a_1g increased because of the structural strain of the Na_0.7CoO₂ thin film. It is inferred that the structural strain is the source for the lower resistivity and the preservation of the strongly correlated system up to 200 K for the Na_0.7CoO₂ thin film. On the other hand, the strain in the Na_0.5CoO₂ thin film was not affected, and the charge-ordering state and the Na content (x=0.5) only cause the charge-ordering state.     

The Crystal Chemistry of Lithium in the Alluaudite Structure: A Study of the (Na1−xLix)CdIn2(PO4)3 Solid Solution (x=0 to 1)

Several compounds of the (Na_1−xLi_x)CdIn₂(PO₄)₃ solid solution were synthesized by a solid-state reaction in air, and pure alluaudite-like compounds were obtained for x=0.00, 0.25, and 0.50. X-ray Rietveld refinements indicate the occurrence of Cd²⁺ in the M(1) site, and of In³⁺ in the M(2) site of the alluaudite structure. This non-disordered cationic distribution is confirmed by the sharpness of the infrared absorption bands. The distribution of Na⁺ and Li⁺ on the A(1) and A(2)′ crystallographic sites cannot be accurately assessed by the Rietvled method, probably because the electronic densities involved in the Na⁺→Li⁺ substitution are very small. A comparison with the synthetic alluaudite-like compounds, (Na_1−xLi_x)MnFe₂(PO₄)₃, indicates the influence of the cations occupying the M(1) and M(2) sites on the coordination polyhedra morphologies of the A(1) and A(2)′ crystallographic sites.     

Crystal Structure, Electric and Magnetic Properties of Layered Cobaltite β-NaxCoO2

The layered oxide thermoelectric material β-Na_0.67CoO₂ has been studied by powder neutron diffraction, electric and magnetic measurements. This compound includes an edge-sharing CoO₆ slab and a highly vacant Na⁺ sheet in a unit cell (space group symmetry C2/m, a=4.9023(4) Å, b=2.8280(2) Å, c=5.7198(6) Å and β=105.964(6)° at 300 K). The evaluated formal valence of cobalt ion, +3.33(1), is ascribed to the coexistence of Co³⁺ and Co⁴⁺ in the ratio 2:1. Polycrystalline β-Na_0.67CoO₂, a p-type thermoelectric material, exhibits metallic behavior of the electric resistivity below 300 K. The Curie-Weiss-type magnetic susceptibility indicates antiferromagnetic interactions between magnetic cobalt ions in the edge-sharing CoO₆ slab.     

Thermoelectric properties of polycrystalline La1−xSrxCoO3

Thermoelectric properties of polycrystalline La_1−xSr_xCoO₃, where Sr²⁺ is substituted in La³⁺ site in perovskite-type LaCoO₃, have been investigated. Sr-doping increases the electrical conductivity (σ) of La_1−xSr_xCoO₃, and also decreases the Seebeck coefficient (S) for 0.01?x?0.40. A Hall coefficient measurement reveals that the increase in electrical conductivity arises from increases in both carrier concentration and the Hall mobility. The decrease in the Seebeck coefficient is caused by a decrease in carrier effective mass as well as increase in carrier concentration. The highest power factor (σS²) is 3.7×10⁻⁴ W m⁻¹ K⁻² at 250 K for x=0.10. The thermal conductivity (κ) is about 2 W m⁻¹ K⁻¹ at 300 K for 0?x?0.04, and increases for x?0.05 because of an increase in heat transport by conductive carrier. The thermoelectric properties of La_1−xSr_xCoO₃ are improved by Sr-doping, and the figure of merit (Z=σS² κ⁻¹) reaches 1.6×10⁻⁴ K⁻¹ for x=0.06 at 300 K (ZT=0.048). For heavily Sr-doped samples, the thermoelectric properties diminish mainly because of the decrease in the Seebeck coefficient and the increase in thermal conductivity.     

Thermochemistry of Li1+xMn2−xO4 (0?x?1/3) spinel

Lithium substituted Li_1+xMn_2−xO₄ spinel samples in the entire solid solution range (0?x?1/3) were synthesized by solid-state reaction. The samples with x<0.25 are stoichiometric and those with x?0.25 are oxygen deficient. High-temperature oxide melt solution calorimetry in molten 3Na₂O·4MoO₃ at 974 K was performed to determine their enthalpies of formation from constituent binary oxides at 298 K. The cubic lattice parameter was determined from least-squares fitting of powder XRD data. The variations of the enthalpy of formation from oxides and the lattice parameter with x follow similar trends. The enthalpy of formation from oxides becomes more exothermic with x for stoichiometric compounds (x<0.25) and deviates endothermically from this trend for oxygen-deficient samples (x?0.25). This energetic trend is related to two competing substitution mechanisms of lithium for manganese (oxidation of Mn³⁺ to Mn⁴⁺ versus formation of oxygen vacancies). For stoichiometric spinels, the oxidation of Mn³⁺ to Mn⁴⁺ is dominant, whereas for oxygen-deficient compounds both mechanisms are operative. The endothermic deviation is ascribed to the large endothermic enthalpy of reduction.     

Evolution of structure and magnetic properties in electron-doped double perovskites, Sr2−xLaxMnWO6 (0?x?1)

Powder neutron and X-ray diffraction studies show that the double perovskites in the region 0?x?1 exhibit two crystallographic modifications at room temperature: monoclinic P2₁/n and tetragonal I4/m, with a boundary at 0.75<x<0.9. Magnetic susceptibility measurements indicate that for x=0 and 0.5 Sr_2−xLa_xMnWO₆ orders antiferromagnetically (AFM) at 15 and 25 K, respectively, for 0.75?x<1.0, a contribution of weak ferromagnetism (FM), probably due to canted-AFM order, increases with increasing x. The end point compound SrLaMnWO₆ shows the strongest FM cluster effect; however, no clear evidence of magnetic order is discernable down to 4.2 K. X-ray absorption spectroscopy (XAS) confirms Mn²⁺ and mixed-valent W^6+/5+ formal oxidation states in Sr_2−xLa_xMnWO₆.     

La doping of the Sr2CoWO6 double perovskite: A structural and magnetic study

La-doped Sr₂CoWO₆ double perovskites have been prepared in air in polycrystalline form by solid-state reaction. These materials have been studied by X-ray powder diffraction (XRPD), neutron powder diffraction (NPD) and magnetic susceptibility. The structural refinement was performed from combined XRPD and NPD data (D2B instrument, λ=1.594 Å). At room temperature, the replacement of Sr²⁺ by La³⁺ induces a change of the tetragonal structure, space group I4/m of the undoped Sr₂CoWO₆ into the distorted monoclinic crystal structure, space group P2₁/n, Z=2. The structure of La-doped phases contains alternating CoO₆ and (Co/W)O₆ octahedra, almost fully ordered. On the other hand, the replacement of Sr²⁺ by La³⁺ induces a partial replacement of W⁶⁺ by Co²⁺ into the B sites, i.e. Sr_2−xLa_xCoW_1−yCo_yO₆ (y=x/4) with segregation of SrWO₄. Magnetic and neutron diffraction measurements indicate an antiferromagnetic ordering below T_N=24 K independently of the La-substitution.     

Structure and electron density analysis of electrochemically and chemically delithiated LiCoO2 single crystals

Single crystals of Li_0.68CoO₂, Li_0.48CoO₂, and Li_0.35CoO₂ were successfully synthesized for the first time by means of electrochemical and chemical delithiation processes using LiCoO₂ single crystals as a parent compound. A single-crystal X-ray diffraction study confirmed the trigonal R3¯m space group and the hexagonal lattice parameters a=2.8107(5) Å, c=14.2235(6) Å, and c/a=5.060 for Li_0.68CoO₂; a=2.8090(15) Å, c=14.3890(17) Å, and c/a=5.122 for Li_0.48CoO₂; and a=2.8070(12) Å, c=14.4359(14) Å, and c/a=5.143 for Li_0.35CoO₂. The crystal structures were refined to the conventional values R=1.99% and wR=1.88% for Li_0.68CoO₂; R=2.40% and wR=2.58% for Li_0.48CoO₂; and R=2.63% and wR=2.56% for Li_0.35CoO₂. The oxygen-oxygen contact distance in the CoO₆ octahedron was determined to be shortened by the delithiation from 2.6180(9) Å in LiCoO₂ to 2.5385(15) Å in Li_0.35CoO₂. The electron density distributions of these Li_xCoO₂ crystals were analyzed by the maximum entropy method (MEM) using the present single-crystal X-ray diffraction data at 300 K. From the results of the single-crystal MEM, strong covalent bonding was clearly visible between the Co and O atoms, while no bonding was found around the Li atoms in these compounds. The gradual decrease in the electron density at the Li site upon delithiation could be precisely analyzed.     

Synthesis and structural study of a new NASICON-type solid solution: Li1−xLax/3Zr2(PO4)3

A new complete solid solution of NASICON-type compounds between LiZr₂(PO₄)₃ and La_1/3Zr₂(PO₄)₃ was evidenced with the general formula Li_1−xLa_x/3Zr₂(PO₄)₃ (0?x?1). These phases were synthesized by a complex polymerizable method and structurally characterized from Rietveld treatment of their X-ray and neutron powder diffraction data. This solid solution results from the substitution mechanism Li⁺→1/3La³⁺+2/3□ leading to an increase of the vacancies number correlated to an increase of the La content. According to this substitution mechanism, the general formula can then be written Li_1−xLa_x/3□_2x/3Zr₂(PO₄)₃ (0?x?1) in order to underline the correlation between the La content and the vacancies rate. For all the compounds, the structure is clearly related to that of the NASICON family with three crystallographic domains evidenced. For 0?x?0.5, all the members adopt at high temperature the typical NASICON-type structure (s.g. R3¯c), while at lower temperature, their structure distorts to a triclinic form (s.g. C 1¯), as observed for LiZr₂(PO₄)₃ prepared above 1100 °C. Moreover, in this domain, the reversible transition is clearly soft and the transition temperature strongly depends of the x value. For 0.6?x?0.9, the compounds crystallize in a rhombohedral cell (s.g. R3¯), while for x=1, the phase La_1/3Zr₂(PO₄)₃ is obtained (s.g. P3¯, Z=6, a=8.7378(2) Å, c=23.2156(7) Å).This paper is devoted to the structure analysis of the series Li_1−xLa_x/3Zr₂(PO₄)₃ (0?x?1), from X-ray and neutron powder thermo diffraction and transmission electron microscopy (TEM) studies.     

Kinetic study of methane oxidation over perovskite oxides La1?xSrxCoO3

Methane oxidation over perovskite oxide (La_1−xSr_xCoO₃) were investigated under rich oxygen circumstance. The large x in oxide or the higher temperature will promote the lattice oxygen to participate in the reaction. The relative adsorption properties of catalyst and reaction kinetic were also studied.     

Doping studies of the magnetic cobaltocuprate CoSr2Y2−xCexCu2O9±δ

A structural, magnetic and electronic study of the cobaltocuprate CoSr₂Y_2−xCe_xCu₂O_9±δ (x=0.5-0.8) has been performed. All materials crystallise in the orthorhombic Cmcm symmetry space group in which chains of corner linked CoO₄ tetrahedra run parallel to the 1 1 0 direction. An antiferromagnetic transition is observed for x=0.5-0.8; T_M increases with x. A change in the dimensionality of the magnetic order occurs at x=0.8 as the interchain distance increases to a critical value. There is charge transfer between the cuprate planes and cobaltate layer as Ce doping increases, so that Co³⁺ is partially oxidised to Co⁴⁺ with a concomitant reduction in the valence of Cu. Superconductivity is not observed in any of the samples and a crossover from Mott to Efros and Shklovskii variable range hopping behaviour is evidenced as x increases from 0.5 to 0.8.     

Thermochemistry of La0.7Sr0.3Mn1−xFexO3 solid solutions (0<x<1)

The structure, the energetics and the internal redox reactions of La_0.7Sr_0.3Fe_xMn_1−xO₃ have been studied in the complete solid solution range 0.0<x<1.0. High temperature oxide melt drop solution calorimetry was performed to determine the enthalpies of formation from binary oxides and the enthalpy of mixing. There is a noticeable change in the energetics of the solid solution near x=0.7, which is due to the growing concentration of Fe⁴⁺ at higher Fe/(Fe+Mn) ratio. The balance between different valences of the transition metals, Mn and Fe, is the main factor in determining the energetics of the La_0.70Sr_0.30Fe_xMn_1−xO₃ solid solution.     

Thermally activated and non-activated charge transport processes in the oxides NaxMo2

The electrical properties of Na_xM_1+yO₂ (M=Mn,Co) were measured as a function of temperature under conditions of thermodynamic equilibrium for a quenched defect structure. The results of electrochemical studies of Na_xM_1+yO₂ are also presented. A correlation is demonstrated between the structures of the ionic and electronic defects in these materials and the potential changes of the cathode in Na/Na⁺/Na_xM_1+yO₂.The author is grateful to Prof. S. Mrowec and Dr. A. Stoklosa for helpful discussions.     

Phase transitions in A-site substituted perovskite compounds: The (Ca1-2xNaxLax)TiO3 (0?x?0.5) solid solution

The (Ca_1-2xNa_xLa_x)TiO₃ (0?x?0.5) A-site substituted perovskite compounds have been synthesized and characterized by XRD and Raman spectroscopy at room temperature. The XRD powder diffraction study suggests that the end-member Na_1/2La_1/2TiO₃ crystallizes in the tetragonal space group I4/mcm. The phase transition from Pbnm to I4/mcm is located between x=0.34 and 0.39 and is driven by the variation of ionic radii at the A-site. The observed Raman modes are in agreement with group theory analysis, and the relationships between the behavior of structural parameters (e.g. Ti-O-Ti bond angle), indicated by long-range order, and the corresponding Raman frequency shifts and intensity evolution, indicated by short-range order, are established and discussed in terms of the radius effect and the mass effect.     

Single-crystal synthesis, structure analysis, and physical properties of the calcium ferrite-type NaxTi2O4 with 0.558<x<1

Single crystals of calcium ferrite CaFe₂O₄-type NaTi₂O₄ having millimeter-sized needle shapes were synthesized by a reaction of Na metal and TiO₂ in a sealed iron vessel at 1473 K. Sodium-deficient Na_xTi₂O₄ single crystals with 0.558<x<1 were successfully synthesized by a topotactic oxidation reaction using NaTi₂O₄ single crystals as parent materials. The crystal structures of Na_xTi₂O₄ with x=0.970, 0.912, 0.799, 0.751, 0.717, 0.686, 0.611, and 0.558 were determined by the single-crystal X-ray diffraction method. The basic framework constructed by the Ti1O₆ and Ti2O₆ double rutile chains was maintained in these Na_xTi₂O₄ compounds. Based on the results of bond valence analysis, we speculated that the Ti1 sites are preferentially occupied by Ti³⁺ cations over the compositional range of 0.8<x<1, while both the Ti1 and Ti2 sites are randomly occupied by Ti³⁺ and Ti⁴⁺ cations at x=0.558. Magnetic susceptibility data indicated that the broad maximum around 40 K observed in as-grown NaTi₂O₄ is suppressed by an Na deficiency and vanishes in Na_0.717Ti₂O₄. The electrical resistivity increased with the Na deficiency; however, it was still semiconductive in Na_0.799Ti₂O₄.     

Synthesis and electrical conductivity of perovskite-type PrCo1−xMgxO3

Oxides in the system PrCo_1−xMg_xO₃ (x=0.0, 0.05, 0.10, 0.15, 0.20, 0.25) were synthesized by citrate technique and characterized by powder X-ray diffraction and scanning electron microscope. All compounds have a cubic perovskite structure (space group ). The maximum ratio of doped Mg in the system PrCo_1−xMg_xO₃ is x=0.2. Further doping leads to the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃. The substitution of Mg for Co improves the performance of PrCoO₃ as compared to the electrical conductivity measured by a four-probe electrical conductivity analyzer in the temperature range from 298 to 1073 K. The substitution of Mg for Co on the B site may be compensated by the formations of Co⁴⁺ and oxygen vacancies. The electrical conductivity of PrCo_1−xMg_xO₃ oxides increases with increasing x in the range of 0.0-0.2. The increase in conductivity becomes considerable at the temperatures ?673 K especially for x?0.1; it reaches a maximum at x=0.2 and 1073 K. From x>0.2 the conductivity of PrCo_1−xMg_xO₃ starts getting lower. This is probably a result of the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃ , which blocks oxygen transport, and association of oxygen vacancies. A change in activation energy for all PrCo_1−xMg_xO₃ compounds (x=0-0.25) was observed, with a higher activation energy above 573 K and a lower activation energy below 573 K. The reasons for such a change are probably due to the change of dominant charge carriers from Co⁴⁺ to Vö in PrCo_1−xMg_xO₃ oxides and a phase transition mainly starting at 573 K.     

Photoluminescence properties of a novel phosphor, Na3La9O3(BO3)8:RE(RE=Eu,Tb)

The new oxyborate phosphors, Na₃La₉O₃(BO₃)₈:Eu³⁺ (NLBO:Eu) and Na₃La₉O₃(BO₃)₈:Tb³⁺ (NLBO:Tb) were prepared by solid-state reactions. The photoluminescence characteristics under UV excitation were investigated. The dominated emission of Eu³⁺ corresponding to the electric dipole transition ⁵D₀→⁷F₂ is located at 613 nm and bright green luminescence of NLBO:Tb attributed to the transition ⁵D₄→⁷F₅ is centered at 544 nm. The concentration dependence of the emission intensity showed that the optimum doping concentration of Eu and Tb is 30% and 10%, respectively.     

Analysis of magnetic and structural phase transition behaviors of La1−xSrxCrO3 for preparation of phase diagram

The phase transition behavior of perovskite-type compounds, La_1−xSr_xCrO₃, was investigated by differential scanning calorimetry (DSC), dilatometry, dc magnetic susceptibility measurement and X-ray diffraction analysis. Both second-order magnetic phase transition from antiferromagnetic to paramagnetic and first-order structural phase transition from orthorhombic to rhombohedral were observed in the DSC or dilatometric curve of every specimen. The temperatures of both these magnetic and structural phase transitions decreased linearly with an increase in Sr content. The structural phase transition temperature of La_1−xSr_xCrO₃ with x less than 0.11 is higher than the magnetic phase transition temperature; however, a larger decrease in structural phase transition temperature than in magnetic phase transition temperature was observed with an increase in Sr content, resulting in a structural phase transition temperature lower than the magnetic phase transition temperature for La_1−xSr_xCrO₃ with x of more than 0.12. It was also observed that the heat of absorption of the structural phase transition decreased with an increase in x. In the dependence of dc magnetic susceptibility on temperature, variations by not only magnetic but also structural phase transitions were observed. It was also revealed that thermal expansion coefficient is affected not only by structural phase transition but also magnetic phase transition. Magnetic and structural phase diagram of La_1−xSr_xCrO₃, suggesting the existence of two Sr contents and temperatures at which triple phases coexist, was proposed.     

Crystal Structure of Pseudorhombohedral InFe1−xTixO3+x/2 (x=2/3)

The structure of pseudorhombohedral-type InFe_1−xTi_xO_3−x/2 (x=2/3) was refined by Rietveld profile fitting. The crystal is a commensurate member of a series in a solution range on InFeO₃-In₂Ti₂O₇ including incommensurate structures. The structure with the unit cell of a=5.9188(1), b=10.1112(2), and c=6.3896(1) Å, β=108.018(2)°, and a space group P2₁/a is the alternate stacking of an edge-shared InO₆ octahedral layer and an Fe/Ti-O plane along c^*. Metal sites on the Fe/Ti-O plane are surrounded by four oxygen atoms on the Fe/Ti-O plane and two axial ones. Electric conductivities of the order 10⁻⁴ S/cm were observed for the samples at 1000 K, while the oxide ion transport number is almost zero as no electromotive force was detected by an oxygen concentration cell.