Scholte Wave at Air-Metal Interface Generated by a Pulsed Disc-Like Source

The normal displacement and pressure of Scholte and Leaky Rayleigh waves at air-metal interface generated by a pulsed disc-like source are simulated theoretically by the Cagniard-de Hoop method and studied by laser ultrasound technique experimentally. It is found that the Scholte wave detected by a photorefractive interferometer is mainly contributed by the surface pressure and the Leaky Rayleigh wave is dominated by the surface displacement. It is also proven that the pulse width of these interface waves is mainly determined by the acoustic time delay on the generating source size under our experimental conditions.     

激光超声方法研究固-固界面波传播特性

对界面波的传播特性进行了理论及实验研究.首先探讨了界面波的求根问题，基于黎曼面分析，给出了求解界面波特征方程所有根的一般方法.理论上对三种常见的界面波——Stoneley波，Leaky Rayleigh及Leaky Interface波传播机理进行了分析，描述了三种界面波的波矢及位移势在两种介质中的状态.最后基于光弹效应原理, 利用全光学的激光超声手段对界面波进行了实验测量，实测结果与理论符合很好.     

流-固界面波的激光激发与光偏转检测

基于光偏转原理,研制了可用于流-固界面波探测的光纤传感装置.在此基础上,建立了以调Q Nd∶YAG激光为流-固界面波激发光源的实验系统.实验上探测了激光在空气-铝、水-铝和酒精-铝等界面上激发的界面波波形.根据实验波形,算得在这三种界面上的泄漏Rayleigh波和Scholte波的速度分别为2889 m/s和339 m/s、2916 m/s和1512 m/s、2872 m/s和1184 m/s,此实验值与理论计算值相比,偏差小于5％.     

All-optical excitation and detection of leaky Rayleigh waves

The results of experiments on all-optical monitoring of leaky Rayleigh waves are reported. Leaky Rayleigh waves were excited by pulsed laser action on a liquid-solid interface and were detected by the light-beam-deflection technique. Both the measured velocity of their propagation and the attenuation are in good agreement with theoretical predictions. Possible applications include acoustic spectroscopy of materials, depth profiling of layered structures, and tabletop modeling of seismic phenomena.     

The thermoelastic excitation of air-solid interface waves using the pulsed laser

In the 1920s, the solid-solid interface wave, Stoneley wave, was first studied by Stoneley. From the 1930s to 1940s, the fluid-solid interface waves, usually called Scholte wave or Scholte-Stoneley wave, were studied by Cagniard and Scholte respec-tively[1]. The Scholte wave corresponds to the real root of the fluid-solid interface secu-lar equation, which is usually called the Scholte equation, and the velocity of Scholte wave is only slightly lower than the longitudinal velocity of the f…     

Laser-induced thermoelastic Leaky Lamb waves at the fluid–solid interface

A model based on the theory of fluid–structure interaction is developed to simulate the laser thermoelastic generation and propagation of Leaky Lamb waves at the water–aluminum interface. Each component of displacement, stress, and temperature are derived in transform domain by the photothermoelastic transfer matrix method. The time domain solutions are obtained by numerically inverting the transforms while the dispersion curves and attenuation curves for the leaky waves are also calculated. Then the propagation characteristics of different modes are analyzed. The model establishes a quantitative relation between the laser parameters, the material parameters, the corresponding waveforms, and the dispersion curves, which provides a useful tool for the Leaky Lamb waves applied to nondestructive evaluation.     

流体-镀层基底界面波的传播特性

理论分析了脉冲激光激发的流体-分层固体结构声场,在此基础上数值计算了流体-慢层快底固体和流体-快层慢底固体结构液-固界面Scholte波的频散特性与瞬态响应.数值结果显示,对于流体-慢层快底结构,Scholte界面波呈现出正常频散特性;而对于流体-快层慢底结构,Scholte波在较小的频厚积范围呈反常频散特性.理论瞬态信号也显示了同样的特性.采用脉冲激光激励,用水听器接收的方式进行了Scholte界面波的实验测量.实验测量和分析结果与理论结果有很好的一致性.此工作可为水浸检测条件下镀层与薄膜材料参数的超声无损表征、海底沉积物参数反演等应用提供理论基础.     

The reflection of bounded inhomogeneous waves on a liquid/solid interface

Fourier analysis and normal mode theory are used to describe the reflection of bounded inhomogeneous waves on a liquid/solid interface. Nonspecular reflection phenomena in the Rayleigh angle are studied in detail. In this way, an explanation is given for the Rayleigh dip phenomenon for positive inhomogeneity factors and the related result of a reflection coefficient larger than unity when the sign of the inhomogeneity factor is reversed. In the limit of large beamwidths, the reflection coefficient predicted by the infinite plane inhomogeneous wave theory is obtained. These results are entirely consistent with the experimental work published by Deschamps [J. Acoust. Soc. Am. 96, 2841-2848 (1994)]. The energy efficiency of Rayleigh wave excitation is investigated as well. It is shown that for large beamwidths, the energy efficiency for bounded inhomogeneous waves is considerably higher in comparison with Gaussian and square-profiled beams.     

Surface acoustic waves at the vacuum-thermoviscoelastic solid interface

The present investigation concerns the propagation of surface waves at the vacuum-solid interface of a solid which is isotropic and thermoviscoelastic, i.e., for which the effects of heat conductivity need to be taken into account. Calculations show that, in addition to the Rayleigh wave, a thermal surface wave propagates that couples both the thermal and the elasticity effects. This latter wave is interpreted in terms of evanescent plane waves. The displacement field associated with this wave is calculated and interpreted. Some experimental results are also presented.     

Acoustic field excited by a pulsed laser line source in a cylinder

The excitation and propagation of the acoustic waves in an elastic cylinder are studied by laser ultrasonics both theoretically and experimentally. The theoretical analysis of the two-dimensional acoustic field excited by a pulsed laser line source impacting on the generatrix of an elastic cylinder is presented. The dispersive properties for both cylindrical Rayleigh wave and the higher modes--whispering gallery (WG) modes are analyzed in detail. The numerical transient displacement waveforms for a detecting point located another terminal of the cylinder diameter opposite the source are calculated. The experimental excitation and detection of the acoustic waves in an aluminum cylinder are carried out on a laser ultrasonic system, which mainly consists of a Q-switched Nd:YAG laser and a laser interferometer. The wave components of bulk waves and surface waves (cylindrical Rayleigh waves and WG modes) are analyzed by comparing the numerical and experimental waveforms. The results are in good agreement.     

Simulation on laser-induced surface acoustic wave on isotropic cylinders by finite element method

Based on the thermoelastic theory, a finite element model is developed to simulate the process of laser inducing ultrasonic field in isotropic cylinders, which can take the temperature dependence of thermal parameters into account. Using the finite element model, we have simulated the ultrasonic fields induced by a pulse laser line source impacting on the generatrix of aluminum cylinders with different diameters. And the intact waveforms of surface acoustic wave (SAW including cylindrical Rayleigh and Whispering gallery (WG) modes) are presented, which are in very good agreement with the calculated and experimental waveforms in other literatures. Furthermore, the dispersion properties of cylindrical Rayleigh waves are analyzed by the method of phase spectral analysis, and the results show that with the increasing frequency, the phase velocity of cylindrical Rayleigh wave rapidly increases to the maximum value, and then gradually decreases to that of plane Rayleigh wave. With the diameter of cylinder decreasing, the maximum value of phase velocity and the corresponding frequency increase.     

Propagation of Leaky Interface Waves at a Solid Boundary under Pulse Excitation

Acoustical Physics - Leaky interface wave generated by pulse excitation is investigated. According to different physical significance of wave solutions, appropriate solutions are selected to...     

激光超声检测带过渡圆角平板表面缺陷的数值研究

为了研究激光激发出的超声波在带过渡圆角的金属平板上的传播规律和检测表面缺陷的方法，采用有限元法模拟了该类平板中的激光超声现象，分析了表面波在圆角区域的传播规律和与表面缺陷的作用过程。数值结果表明:激光激发出纵波、横波和Rayleigh波等，其中Rayleigh波主要存在于表面mm量级，并且在过渡圆角处发生模式转换生成了直达波R′和模式转换波R_R等多种表面波；经过过渡区域后的声波在表面缺陷处发生了反射和透射现象，通过B扫图可以检测缺陷的位置。随着缺陷深度的增加，表面波的透射系数不断减小，且透射波R_t和R_st存在0.5 μs左右的到达时间差，该时间差与缺陷深度近似成线性正相关。数值结果为激光超声检测带过渡圆角的平板表面缺陷提供了有价值的参考。     

Elastic characterization of platinum/rhodium alloy at high temperature by combined laser heating and laser ultrasonic techniques

We demonstrate an innovative pump–probe technique combined with laser heating to determine the velocity of a surface Rayleigh wave at high temperature. Laser ultrasonics in a point-source–point-receiver configuration was combined with laser heating to evaluate the elastic properties of micron size specimens. The measurements of the velocity of the surface Rayleigh wave (SRW) were conducted at 1070 K.     

基于虚拟源技术的双层固体结构超声成像

本文提出虚拟源与合成孔径技术相结合的成像方法来实现对双层结构的内部缺陷成像。通过相控阵探头延时聚焦的方法在界面形成虚拟声源,并对有机玻璃/钢双层结构中的聚焦声场进行了仿真,结果显示聚焦声束穿过界面后形成扩散球面波,适合采用合成孔径聚焦技术成像。实验中采用128阵元探头对含有横穿孔缺陷的有机玻璃/钢样品进行测量和波形采集,应用自适应滤波方法抑制界面回波,最后对波形使用合成孔径聚焦成像,得到的图像比B扫描成像具有较高的信噪比和横向分辨率,并且分辨率不随深度变化。     

激光激发黏弹表面波有限元数值模拟

研究黏弹性材料中激光激发的Rayleigh波的传播特征. 考虑到黏弹性材料的黏性特征,在频域内建立黏弹性材料中激光激发Rayleigh波的有限元数值模型. 在验证有限元频域数值模型正确性的基础上,模拟脉冲激光作用在黏弹性材料上激发出Rayleigh波,进而讨论激光激发的黏弹Rayleigh波的传播特征,并比较黏弹性材料与弹性材料中激光激发的Rayleigh波差异,同时分析了材料的黏性劲度参量变化对Rayleigh波特征的影响. 关键词： 表面波 激光超声 有限元方法 黏弹性     

有限入射声束在液固界面声反射的数值研究

采用将有限声束分解为一系列平面波的方法，对液固界面声束的声反射问题进行了数值研究，结果表明，当声束入射角为瑞利疲激角时，反射声速有明显位移；当声束在液固界面“掠射”时，反射声速显著变宽，文中还讨论了束宽对反射声速横截面上声场分布的影响。     

Scattering of a Rayleigh surface acoustic wave by a small-size inhomogeneity in a solid half-space

We use the Born approximation of the perturbation method to solve the problem of scattering of a harmonic Rayleigh surface acoustic wave by a weak-contrast inhomogeneity that is small compared with the wavelength and is located in a solid half-space near its boundary. The material of the inhomogeneity differs from the material of the half-space only in its density. The Rayleigh wave incident on the inhomogeneity is excited by a monochromatic surface force source acting normally to the half-space boundary. We derive expressions for the displacement fields in the scattered spherical compressional and shear (SV- and SH-polarized) waves. Scattering of the Rayleigh wave into a Rayleigh wave is studied in detail. We find expressions for the vertical and horizontal components of the displacement vector in the scattered Rayleigh wave as well as its radiated power. It is shown that the field of the scattered surface wave is mainly formed by vertical oscillations of the inhomogeneity in the field of the incident wave. In this case, the radiated power for the scattered Rayleigh wave formed by vertical motion of the inhomogeneity in the incident-wave field depends on the depth of the inhomogeneity as the fourth power of the function describing the well-known depth dependence of the vertical displacements in the Rayleigh surface wave. Correspondingly, the dependence of the radiated power for the scattered Rayleigh wave formed by horizontal motion of the inhomogeneity depends on its location depth as the fourth power of the depth dependence of the horizontal displacements in the Rayleigh surface wave. We perform calculations of the ratio between the powers of the scattered and incident Rayleigh waves for different ratios between the velocities of the compressional and shear waves in a solid. It is shown that the radiated power for the scattered surface wave decreases sharply with increasing depth of the subsurface-inhomogeneity location. Thus, the scattering of a Rayleigh wave into a Rayleigh wave is fairly efficient only when the location depth of the inhomogeneity does not exceed about one-third of the wavelength of the shear wave in an elastic medium.     

Reflection of structural waves at a solid/liquid interface

This paper investigates the reflection characteristics of structural or guided waves in rods at a solid/liquid interface. Structural waves, whose wavelengths are much larger than the diameter of the rod, are described in a first approximation by classical one-dimensional wave theory. The reflection characteristics of such waves at a solid/liquid (melting) interface has been reported by two different ultrasonic measurement techniques: first, measuring the fast regression rate of a melting interface during the burning of metal rod samples in an oxygen-enriched environment, and second, monitoring the propagation of the solid/liquid interface during the slow melting and solidification of a rod sample in a furnace. The second work clearly shows that the major reflection occurs from the solid/liquid interface and not the liquid/gas interface as predicted by plane longitudinal wave reflectivity theory. The present work confirms this observation by reporting on the results of some specially designed experiments to identify the main interface of reflection for structural waves in rods. Hence, it helps in explaining the fundamental discrepancy between the reflection characteristics at a solid/liquid interface between low frequency structural waves and high frequency bulk waves, and confirms that the detected echo within a burning metallic rod clearly represents a reflection from the solid/liquid interface.     

Optical methods in fault dynamics

The Rayleigh pulse interaction with a pre-stressed, partially contacting interface between similar and dissimilar materials is investigated experimentally as well as numerically. This study is intended to obtain an improved understanding of the interface (fault) dynamics during the earthquake rupture process. Using dynamic photoelasticity in conjunction with high-speed cinematography, snapshots of time-dependent isochromatic fringe patterns associated with Rayleigh pulse–interface interaction are experimentally recorded. It is shown that interface slip (instability) can be triggered dynamically by a pulse which propagates along the interface at the Rayleigh wave speed. For the numerical investigation, the finite difference wave simulator SWIFD is used for solving the problem under different combinations of contacting materials. The effect of acoustic impedance ratio of the two contacting materials on the wave patterns is discussed. The results indicate that upon interface rupture, Mach (head) waves, which carry a relatively large amount of energy in a concentrated form, can be generated and propagated from the interface contact region (asperity) into the acoustically softer material. Such Mach waves can cause severe damage onto a particular region inside an adjacent acoustically softer area. This type of damage concentration might be a possible reason for the generation of the “damage belt” in Kobe, Japan, on the occasion of the 1995 Hyogo-ken Nanbu (Kobe) Earthquake.