ZSM-5/ZSM-57复合分子筛催化剂上混合C4烃的催化转化反应

以ZSM-5/ZSM-57复合分子筛为催化剂, 考察了其对混合C4烃催化转化的反应性能. 采用氨程序升温脱附(NH3-TPD)和吡啶吸附傅立叶变换红外(FT-IR)光谱技术表征复合分子筛的酸性质. 结果表明, 当复合分子筛中ZSM-5的含量较低时, 比ZSM-5具有更高的催化活性及乙烯和丙烯选择性, 这是因为此时复合分子筛酸强度较高、酸量较多, 且小孔ZSM-57有利于乙烯和丙烯的择形反应. 而当复合分子筛中ZSM-5的含量较高时, 具有较高的苯和甲苯选择性, 其原因可能是其孔结构及共晶生长时的结构匹配性对芳构化反应有利.     

ZSM-5／MOR复合分子筛催化剂对混合C4烃转化反应的催化性能

以ZSM-5/丝光沸石(MOR)复合分子筛为催化剂,对混合C4烃的催化转化反应进行了评价,并采用程序升温脱附和原位红外光谱技术对ZSM-5/MOR的酸性进行了表征. 结果表明,与ZSM-5相比, MOR具有很低的催化活性,但ZSM-5/MOR复合分子筛具有较高的催化活性,随着ZSM-5/MOR复合分子筛中ZSM-5含量的增加, C4烃转化率稍有升高;在C4烃转化率大致相同的情况下,乙烯和丙烯的总选择性比较接近,但苯和甲苯的总收率却快速升高. 随着ZSM-5/MOR复合分子筛中ZSM-5含量的增加,弱酸和中强酸的酸量逐渐减少,强酸的酸量有所增加. 由于ZSM-5/MOR复合分子筛中MOR对ZSM-5起到分散作用而产生更多的L酸中心,且此L酸中心处于分子筛的外表面而具有较高的能量,导致苯和甲苯的总收率升高.     

过渡金属改性的ZSM-5催化剂应用于甲硫醚转化制甲硫醇

负载过渡金属的ZSM-5 催化剂用于催化甲硫醚（DMS）转化成甲硫醇（MT）的反应. 实验结果表明,催化剂的甲硫醚转化率提高和甲硫醇选择性降低的趋势一样,都是以下顺序：Co/ZSM-5>Mo/ZSM-5>Ni/ZSM-5>W/ZSM-5. 表征结果表明,由于过渡金属阳离子（W⁶⁺、Ni²⁺、Co³⁺、Mo⁶⁺）比Al³⁺活泼,而改性过程中W⁶⁺、Ni²⁺、Co³⁺、Mo⁶⁺分别代替了部分Al³⁺,使得改性催化剂对DMS和MT的化学吸附作用更强. 过渡金属的引入使得ZSM-5总酸度增强,提高了C―S键的裂解能力,从而改进了催化转化DMS的能力. 研究结果发现,在转化DMS的过程中,金属活性位和酸性位之间通过强的协同效应起作用.     

Conversion of methanol over 10-ring zeolites with differing volumes at channel intersections: comparison of TNU-9, IM-5, ZSM-11 and ZSM-5

Four 3D 10-ring zeolites, IM-5, TNU-9, ZSM-11 and ZSM-5, with Si/Al = 14-24 and crystal sizes below 2 microns, were tested as catalysts for the methanol to hydrocarbons reaction (MTH) at atmospheric pressure, 350 °C and WHSV = 9 h(-1). All catalysts gave initially full methanol conversion, and showed strikingly similar effluent product selectivities. However, their life-time duration differed significantly, and decreased in the order: ZSM-11 > ZSM-5 ? TNU-9 > IM-5. A main difference between the two groups of stability behaviour was the size of cavities formed by channel intersections; larger cavities in TNU-9 and IM-5 leading to polyaromatics formation and a more rapid deactivation compared to ZSM-5 and ZSM-11. Effluent yield-conversion plots suggested that polymethylated benzene intermediates were more important in IM-5 and TNU-9 than in ZSM-5 and ZSM-11, where alkene methylation and cracking reactions seemed to dominate product formation. However, this difference had only minor influence on effluent selectivity.     

SAPO-34分子筛催化丁烯转化制丙烯的研究

通过水热法合成SAPO-34分子筛,将其制成催化剂用于催化丁烯转化制取丙烯,考察了反应温度、空速和铝磷比等对催化性能的影响;还比较了SAPO-34分子筛与ZSM-5分子筛催化该反应的差异.结果表明,在实验范围内,反应温度升高会使得丁烯的转化率明显增高,且丙烯选择性提高;而空速增加,则丁烯的转化率和丙烯选择性降低;铝磷比越大,对丙烯的选择性越差.在有效的反应时间内,SAPO-34分子筛催化效果好于ZSM-5分子筛,但单程寿命较ZSM-5分子筛短.     

Characterization and Activity of Cr, Cu and Ga Modified ZSM—5 for Direct Conversion of Methane to Liquid Hydrocarbons

Direct conversion of methane using a metal-loaded ZSM-5 zeolite prepared via acidic ion exchange was investigated to elucidate the roles of metal and acidity in the formation of liquid hydrocarbons. ZSM-5 (SiO2/A12O3=30) was loaded with different metals (Cr, Cu and Ga) according to the acidic ion-exchange method to produce metal-loaded ZSM-5 zeolite catalysts. XRD, NMR, FT-IR and N2 adsorption analyses indicated that Cr and Ga species managed to occupy the alllmlnum positions in the ZSM-5 framework. In addition, Cr species were deposited in the pores of the structure. However, Cu oxides were deposited on the surface and in the mesopores of the ZSM-5 zeolite. An acidity study using TPD-NH3, FT-IR, and IR-pyridine analyses revealed that the total number of acid sites and the strengths of the BrSusted and Lewis acid sites were significantly different after the acidic ion exchange treatment.Cu loaded HZSM-5 is a potential catalyst for direct conversion of methane to liquid hydrocarbons. The successful production of gasoline via the direct conversion of methane depends on the amount of aluminum in the zeolite framework and the strength of the BrSnsted acid sites.     

Effects of Temperature and Catalyst to Oil Weight Ratio on the Catalytic Conversion of Heavy Oil to Propylene Using ZSM-5 and USY Catalysts

It is useful for practical operation to study the rules of production of propylene by the catalytic conversion of heavy oil in FCC (fluid catalytic cracking). The effects of temperature and C/O ratio (catalyst to oil weight ratio) on the distribution of the product and the yield of propylene were investigated on a micro reactor unit with two model catalysts, namely ZSM-5/Al2O3 and USY/Al2O3, and Fushun vacuum gas oil (VGO) was used as the feedstock. The conversion of heavy oil over ZSM-5 catalyst can be comparable to that of USY catalyst at high temperature and high C/O ratio. The rate of conversion of heavy oil using the ZSM-5 equilibrium catalyst is lower compared with the USY equilibrium catalyst under the general FCC conditions and this can be attributed to the poor steam ability of the ZSM-5 equilibrium catalyst. The difference in pore topologies of USY and ZSM-5 is the reason why the principal products for the above two catalysts is different, namely gasoline and liquid petroleum gas (LPG), repspectively. So the LPG selectivity, especially the propylene selectivity, may decline if USY is added into the FCC catalyst for maximizing the production of propylene. Increasing the C/O ratio is the most economical method for the increase of LPG yield than the increase of the temperature of the two model catalysts, because the loss of light oil is less in the former case. There is an inverse correlation between HTC (hydrogen transfer coefficient) and the yield of propylene, and restricting the hydrogen transfer reaction is the more important measure in increasing the yield of propylene of the ZSM-5 catalyst. The ethylene yield of ZSM-5/Al2O3 is higher, but the gaseous side products with low value are not enhanced when ZSM-5 catalyst is used. Moreover, for LPG and the end products, dry gas and coke, their ranges of reaction conditions to which their yields are dependent are different, and that of end products is more severe than that of LPG. So it is clear that maximizing LPG and propylene and restricting dry gas and coke can be both achieved via increasing the severity of reaction conditions among the range of reaction conditions which LPG yield is sensitive to.     

晶种导向下干胶法合成ZSM-5分子筛

以廉价水玻璃为硅源,在晶种替代有机模板剂的条件下采用干胶法合成了ZSM-5分子筛。利用XRD、SEM、TEM、FTIR、N₂吸附-脱附和NH₃-TPD等分析方法对合成样品进行了表征和测试,考察了合成条件对ZSM-5分子筛晶化过程的影响。结果表明,在硅铝比（n/n）为30~70,钠硅比（n/n）为0.12~0.20时都可以得到结晶度良好的ZSM-5分子筛。研究发现,干胶法合成ZSM-5,在不引入外加水的情况下也可以得到ZSM-5样品,外加水的引入能够有效地提高晶化速率;与水热法合成ZSM-5分子筛相比,干胶法可以显著地缩短晶化时间,同时,合成样品的晶体尺寸也有所减小。     

晶种导向下干胶法合成ZSM-5分子筛

以廉价水玻璃为硅源,在晶种替代有机模板剂的条件下采用干胶法合成了ZSM-5分子筛。利用XRD、SEM、TEM、FTIR、N_2吸附-脱附和NH_3-TPD等分析方法对合成样品进行了表征和测试,考察了合成条件对ZSM-5分子筛晶化过程的影响。结果表明,在硅铝比(n/n)为30~70,钠硅比(n/n)为0.12~0.20时都可以得到结晶度良好的ZSM-5分子筛。研究发现,干胶法合成ZSM-5,在不引入外加水的情况下也可以得到ZSM-5样品,外加水的引入能够有效地提高晶化速率;与水热法合成ZSM-5分子筛相比,干胶法可以显著地缩短晶化时间,同时,合成样品的晶体尺寸也有所减小。     

CuCoMn-zeolite双功能催化剂转化生物质基合成气制取液态烃

选用四种不同的分子筛（SAPO-34, ZSM-5, Y, MCM-41）与CuCoMn（高醇合成组元）构成双功能催化剂,利用N2吸脱附、H2-TPR、XRD、NH3-TPD等表征了催化剂的结构性质. 研究了催化剂在生物质基合成气一段法制取液态烃燃料的应用. 相比于CuCoMn催化剂,加入分子筛的双功能催化剂均不同程度地提高了液体烃燃料的选择性及收率,且收率按顺序递减呈CCM-ZSM-5〉CCM-SAPO-34〉CCM-Y〉CCM-MCM-41. 同时,共沉淀法制备的CuCoMn-ZSM-5 （20wt%, Si/Al=100） 具有最佳的CO转化率（76%）及液体产物收率（30%）. 相比于CuCoMn氧化物,双功能催化剂的比表面及孔容均得到提高. CCM-ZSM-5具有适中的微孔尺寸和中等强度的酸性,增加CCM-ZSM-5中ZSM-5含量或降低ZSM-5中的Si/Al比,均有利于提高酸性位的数量,主要是较弱的酸性位. 而共沉淀法制备的CCM-ZSM-5具有更好的金属分散性及还原性能.     

Acidity Modification of ZSM-5 for Methane Conversion in Co-feeding Method with MTA Reaction

Acidity plays a vital role in methane conversion by co-feeding method, which is one of the best strategies to improve the utilization and gentle the reaction conditions of methane. In this work, Zn, Ni, Mo, La, Ga, Fe and Co-impregnated ZSM-5 zeolites have been prepared with the same substitutions to variate the acidities and tested in co-aromatization of methanol with methane. It is demonstrated that the new medium-strong acid sites formed by metal and strong acid sites are the key role to activate methane in co-reaction. Zn-modified ZSM-5 catalyst is preferred to exhibit the best methane conversion of 12%, whose aromatic selectivity increases from 27.2% to 52.2% compared with that of HZSM-5. Besides, the addition of methane further improves the production of high-valued aromatics compared with methanol to aromatics (MTA) reaction.     

Recent Advances on Gallium-Modified ZSM-5 for Conversion of Light Hydrocarbons

Light olefins are key components of modern chemical industry and are feedstocks for the production of many commodity chemicals widely used in our daily life. It would be of great economic significance to convert light alkanes, produced during the refining of crude oil or extracted during the processing of natural gas selectively to value-added products, such as light alkenes, aromatic hydrocarbons, etc., through catalytic dehydrogenation. Among various catalysts developed, Ga-modified ZSM-5-based catalysts exhibit superior catalytic performance and stability in dehydrogenation of light alkanes. In this mini review, we summarize the progress on synthesis and application of Ga-modified ZSM-5 as catalysts in dehydrogenation of light alkanes to olefins, and the dehydroaromatization to aromatics in the past two decades, as well as the discussions on in-situ formation and evolution of reactive Ga species as catalytic centers and the reaction mechanisms.     

Catalysis Conversion Methane into C2 Hydrocarbons via Electric Field Enhanced Plasma

In this paper the effect of catalyst and carrier in electric field enhanced plasma on methane conversion into C2 hydrocarbons was investigated. Methane coupling reaction was studied in the system of continuous flow reactor on Ni, MoO3, MnO2 catalysts and different ZSM-5 carriers. The per pass conversion of methane can be as high as 22%, the selectivity of ethylene can be as high as 23.8%, of acetylene 60.8%, of ethane 5.4% and of total C2 hydrocarbons was more than 90%. ZSM-5-25 was the better carrier and MnO2 was the better active component. The efficiency of energy was as high as 7.81%.     

ZSM-5分子筛酸位分布及其甲醇制烯烃催化性能的定向管理与调控

ZSM-5分子筛在甲醇制烯烃(MTO)过程中的催化性能和反应机理与其孔道中酸位点分布位置紧密相关. 本文证明在水热合成过程中加入适量的钠离子(Na⁺)可以增加ZSM-5分子筛交叉腔酸位点比例; 从而促进高级甲基苯的生成并加速芳烃循环, 有利于乙烯生成. 相反, 在合成过程中不添加钠离子, 所制备的ZSM-5分子筛直孔道和正弦孔道酸位点比例明显提高, 有利于促进烯烃循环并提高丙烯和C₃₊烯烃选择性.     

Conjugate Conversion of a Broad Fraction of Light Hydrocarbons and Methanol on Zeolite-Containing Catalysts

The effect of modification of ZSM-5 type high-silica zeolites on their acidity and selectivity in formation of lower olefins and arenes in conjugate conversion of propane-butane fraction and methanol was studied.     

硅烷化改性对纳米ZSM-5甲醇制汽油催化剂性能的影响

对比了水热处理后微米ZSM-5和纳米ZSM-5分子筛的物化性质和催化甲醇制汽油(MTG)的反应性能,发现采用纳米ZSM-5分子筛催化剂能得到较高的汽油收率和较长的寿命,但汽油中均四甲苯含量较高.对纳米ZSM-5分子筛进行硅烷化处理,利用低温N_2吸附-脱附、X射线衍射(XRD)、氨气程序升温脱附(NH_3-TPD)对改性前后的样品进行表征.在温度380℃、压力2.0 MPa、空速3.0 h~(-1)的反应条件下进行MTG反应,对硅烷化改性后的催化剂进行评价.结果表明,负载SiO_2后催化剂的强酸中心降低,比表面积和孔容降低.纳米ZSM-5分子筛合适的SiO_2负载量为2%,硅改性后用于MTG反应,催化剂的寿命和汽油收率分别由改性前的144 h和33.6%显著增加到180 h和34.4%.当SiO_2负载量继续增加时,催化剂寿命和汽油收率逐渐降低.另外,随SiO_2负载量的增加,其催化MTG所得汽油产品中的异构烷烃和芳烃含量降低,烯烃和正构烷烃含量增加,均四甲苯含量显著降低,改善了油品质量.     

晶种导向干凝胶法制备成型ZSM-5分子筛

在干凝胶法制备ZSM-5 分子筛的体系中添加晶种导向剂, 控制分子筛的生长, 制备了纳米沸石组装的无粘结剂成型多级孔ZSM-5 分子筛, 一步完成纳米分子筛的制备及组装成型, 即克服了传统纳米粒子难以过滤分离的问题, 同时组装所形成的多级孔有助于改善分子在催化剂内的扩散, 从而提高催化反应效率. 以硅胶、薄水铝石为原料, 四丙基氢氧化铵(TPAOH)和ZSM-5 晶种导向胶作为粘结剂, 通过混捏、挤条得到直径2 mm的条状前驱物, 随后通过干凝胶转换法制备成型分子筛. 所用晶种导向剂组成为0.35TPAOH:1SiO₂:20H₂O:4C₂H₅OH. 通过X射线衍射(XRD), 热重(TG)分析和傅里叶变换红外(FTIR)光谱等方法对分子筛晶化过程进行了表征, 结果表明晶种导向剂加入量对分子筛生长速度及多级孔结构均有影响. 当所加晶种导向剂中TPAOH与SiO₂的摩尔比为0.025时, 经过3 h晶化, 分子筛相对结晶度达到100%. 扫描电镜(SEM)结果表明, 合成的分子筛尺寸约为200 nm, 组装形成的多级孔分子筛的介孔体积为0.28 cm³·g^-1. 通过NH₃ 程序升温脱附(NH₃-TPD)考察了所得成型分子筛的酸性, 发现该分子筛酸性与市售的粉末H-ZSM-5分子筛类似.     

H(M)ZSM-5杂原子分子筛的表面酸性和裂解催化行为

用IR和ITPD技术研究了H(Al)ZSM-5、H(Ga)ZSM-5和H(Fe)ZSM-5杂原子分子筛的表面酸性。结果表明,这些分子筛表面既存在B酸中心,也存在L酸中心,但是就两种酸的表面浓度比值C_L/C_B而言,H(Ga)ZSM-5和H(Fe)ZSM-5要比H(Al)ZSM-5高得多。在十五烷裂解时,L酸中心起的作用可能更大。     

C−C Bond Formation in Syngas Conversion over Zinc Sites Grafted on ZSM-5 Zeolite

Despite significant progress achieved in Fischer–Tropsch synthesis (FTS) technology, control of product selectivity remains a challenge in syngas conversion. Herein, we demonstrate that Zn²⁺-ion exchanged ZSM-5 zeolite steers syngas conversion selectively to ethane with its selectivity reaching as high as 86 % among hydrocarbons (excluding CO₂) at 20 % CO conversion. NMR spectroscopy, X-ray absorption spectroscopy, and X-ray fluorescence indicate that this is likely attributed to the highly dispersed Zn sites grafted on ZSM-5. Quasi-in-situ solid-state NMR, obtained by quenching the reaction in liquid N₂, detects C₂ species such as acetyl (-COCH₃) bonding with an oxygen, ethyl (-CH₂CH₃) bonding with a Zn site, and epoxyethane molecules adsorbing on a Zn site and a Brønsted acid site of the catalyst, respectively. These species could provide insight into C−C bond formation during ethane formation. Interestingly, this selective reaction pathway toward ethane appears to be general because a series of other Zn²⁺-ion exchanged aluminosilicate zeolites with different topologies (for example, SSZ-13, MCM-22, and ZSM-12) all give ethane predominantly. By contrast, a physical mixture of ZnO-ZSM-5 favors formation of hydrocarbons beyond C₃₊. These results provide an important guide for tuning the product selectivity in syngas conversion.     

Bread-template synthesis of hierarchical mesoporous ZSM-5 zeolite with hydrothermally stable mesoporosity

A hierarchical mesoporous ZSM-5 zeolite has been synthesized by using starch-derived bread as a meso-template. The obtained mesoporous ZSM-5 was characterized with X-ray diffraction (XRD), nitrogen sorption, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and thermogravimetric (TG)/differential thermal analysis (DTA) techniques. Hydrothermal treatments revealed that the mesoporosity in hierarchical mesoporous ZSM-5 exhibited excellent hydrothermal stability. Catalytic tests showed that hierarchical mesoporous ZSM-5 was more active than conventional zeolite of ZSM-5 in catalytic cracking of 1,3,5-tri-isopropylbenzene. Hydrogen adsorption measurements showed hierarchical mesoporous ZSM-5 had a higher storage capacity than the conventional ZSM-5.