M-shaped Specimen for the High-strain Rate Tensile Testing Using a Split Hopkinson Pressure Bar Apparatus

An experimental technique is proposed to determine the tensile stress–strain curve of metals at high strain rates. An M-shaped specimen is designed which transforms a compressive loading at its boundaries into tensile loading of its gage section. The specimen can be used in a conventional split Hopkinson pressure bar apparatus, thereby circumventing experimental problems associated with the gripping of tensile specimens under dynamic loading. The M-specimen geometry provides plane strain conditions within its gage section. This feature retards necking and allows for very short gage sections. This new technique is validated both experimentally and numerically for true equivalent plastic strain rates of up to 4,250/s.     

准静态压缩应力-应变曲线测量方法的探索

本文介绍了用应变片直接测量材料的准静态应力-应变曲线的试验研究。在MTS810材料试验机上分别对93W、G50、砂浆等几种材料进行了准静态压缩试验。由于仪器的系统误差不能由MTSCod规准确的得到材料的真实的弹性变形。为此在试件的中部贴应变片得到材料的弹性变形,塑性变形仍旧由MTSCod规记录,从而得到试样的真实的应变,准确获得准静态压缩应力-应变曲线。试验结果表明:在试件中部贴应变片的方法能够准确得到该材料的杨氏模量;在试件两端垫块的刀口上安置Cod规可得到材料的应力应变曲线。两者的合理组合即可得到准确而完整的准静态压缩应力-应变曲线。试验中还发现准静态实验中试件的断面加工不平,偏心压缩等都会影响E的准确测量。     

板材成型中的分叉和断裂及其空洞扩展效应

用平面应力有限元方法分析空洞模型以模拟一种双相钢板材在成型过程中所遇到的微空洞损伤,经试算可使模型的总体和局部的响应与已有的实验相一致,由此可提供描述该材料的损伤本构参数并研究局部剪切带和扩散型颈缩等分叉现象,临界应变值的分布形成了成型极限图中的下限曲线,当空洞模型的总体应力急剧下降或微裂纹开始出现,其相应的总体应变值提供了上限曲线。     

Brittle fracture of precompressed steel as affected by hydrostatic pressure,temperature and strain concentration

Highly precompressed 1020 HR steel, 0.65 prestrain at 400°F (204°C), tested in nominally uniform tension at ?80°F (?62°C) fractures at about 110,000 psi (760 MN/m²) with less than 0.02 plastic strain. Yet the addition of a hydrostatic pressure of less than 7000 psi (48 MN/m²) converts this visually brittle fracture to a ductile one with appreciable necking. The explanation of this surprising experimental result is shown to follow directly and simply from the combination of a tensile stress criterion of fracture, strain concentration and the low tangent modulus of the stress-strain curve in tension beyond the Bauschinger transition region of a few percent of plastic strain. Temperature dependence and strain-rate dependence of brittle fracture similarly are predictable in an almost trivial manner from the appropriate stress-strain curves for different amounts of precompression. So also is the amazingly high ductility or fracture toughness of the most complex of perforated or notched statically loaded structures of mild steel in an undamaged or fully annealed state.     

Determination of tensile flow stress beyond necking at very high strain rate

The objective of this effort was to extend the Bridgman analysis of tensile necking to obtain stress-strain data beyond the point of onset of necking from a split Hopkinson bar. For this purpose, combined analytical and experimental techniques were considered. The analytical efforts were focused on validating the use of Bridgman solutions for high rate of deformation through a finite-element analysis of a tapered tensile specimen. The experimental technique involved the development of a photographic system using a light-emitting diode and a 35-mm rotating drum camera for the observation of necking during dynamic tensile tests conducted with a split Hopkinson tension bar. The developed new technique was successfully used to measure neck profiles of 6061-T6 aluminum, HY100 and 1020 steel tensile specimens. The measured profiles were used with the Bridgman analysis and stress-strain data were obtained to over 70-percent strain.     

Load-Inversion Device for the High Strain Rate Tensile Testing of Sheet Materials with Hopkinson Pressure Bars

A high strain rate tensile testing technique for sheet materials is presented which makes use of a split Hopkinson pressure bar system in conjunction with a load inversion device. With compressive loads applied to its boundaries, the load inversion device introduces tension into a sheet specimen. Two output bars are used to minimize the effect of bending waves on the output force measurement. A Digital Image Correlation (DIC) algorithm is used to determine the strain history in the specimen gage section based on high speed video imaging. Detailed finite element analysis of the experimental set-up is performed to validate the design of the load inversion device. It is shown that under the assumption of perfect alignment and slip-free attachment of the specimen, the measured stress–strain curve is free from spurious oscillations at a strain rate of 1,000 s^?1. Validation experiments are carried out using tensile specimens extracted from 1.4 thick TRIP780 steel sheets. The experimental results for uniaxial tension at strain rates ranging from 200 s^?1 to 1,000 s^?1 confirm the oscillation-free numerical results in an approximate manner. Dynamic tension experiments are also performed on notched specimens to illustrate the validity of the proposed experimental technique for characterizing the effect of strain rate on the onset of ductile fracture in sheet materials.     

A study of localisation in dual-phase high-strength steels under dynamic loading using digital image correlation and FE analysis

Tensile tests were conducted on dual-phase high-strength steel in a Split-Hopkinson Tension Bar at a strain-rate in the range of 150–600/s and in a servo-hydraulic testing machine at a strain-rate between 10^?3 and 10⁰/s. A novel specimen design was utilized for the Hopkinson bar tests of this sheet material. Digital image correlation was used together with high-speed photography to study strain localisation in the tensile specimens at high rates of strain. By using digital image correlation, it is possible to obtain in-plane displacement and strain fields during non-uniform deformation of the gauge section, and accordingly the strains associated with diffuse and localised necking may be determined. The full-field measurements in high strain-rate tests reveal that strain localisation started even before the maximum load was attained in the specimen. An elasto-viscoplastic constitutive model is used to predict the observed stress–strain behaviour and strain localisation for the dual-phase steel. Numerical simulations of dynamic tensile tests were performed using the non-linear explicit FE code LS-DYNA. Simulations were done with shell (plane stress) and brick elements. Good correlation between experiments and numerical predictions was achieved, in terms of engineering stress–strain behaviour, deformed geometry and strain fields. However, mesh density plays a role in the localisation of deformation in numerical simulations, particularly for the shell element analysis.     

Identification of Post-Necking Hardening Phenomena in Ductile Sheet Metal

A combined theoretical/experimental approach accurately quantifying post-necking hardening phenomena in ductile sheet materials that initially exhibit diffuse necking in tension is presented. The method is based on the minimization of the discrepancy between the internal and the external work in the necking zone during a quasi-static tensile test. The main focus of this paper is on the experimental validation of the method using an independent material test. For this purpose, the uniaxial tube expansion test is used to obtain uniaxial strain hardening behavior beyond the point of maximum uniform strain in a tensile test. The proposed method is used to identify the post-necking hardening behavior of a cold rolled interstitial-free steel sheet. It is demonstrated that commonly adopted phenomenological hardening laws cannot accurately describe all hardening stages. An alternative phenomenological hardening model is presented which enables to disentangle pre- and post-necking hardening behavior. Additionally, the influence of the yield surface on the identified post-necking hardening behavior is scrutinized. The results of the proposed method are compared with the hydraulic bulge test. Unlike the hydraulic bulge test, the proposed method predicts a decreased hardening rate in the post-necking regime which might be associated with probing stage IV hardening. While inconclusive, the discrepancy with the hydraulic bulge test suggests differential work hardening at large plastic strains.     

图像相关法在高分子材料拉伸性能研究中的应用

本文对聚碳酸酯(PC)和丙烯腈丁二烯苯乙烯(ABS)的合金(PC/ABS)高分子材料不同环境温度下的拉伸性能进行了试验研究。根据图像相关分析法编制了图像法位移测量分析软件,并对该分析软件的适用性进行了分析。系统研究了PC/ABS高分子材料拉伸试验时三个方向的位移场和应变场。根据测得的位移场研究了该高分子材料拉伸过程中应变和应变率的变化以及应力应变变化规律,并对试验结果进行了详细分析。结果表明,文中采用的图像法位移测量系统具有较高的测试精度;拉伸过程中,试件厚度方向的收缩变形大于宽度方向的收缩变形;颈缩过程区具有非常高的应变率,颈缩后的平直颈缩区的应变率快速下降到一个很低的应变率继续缓慢变形;尽管载荷位移曲线出现了较大的载荷下降现象,PC/ABS拉伸时的真应力应变曲线没有明显的应力下降现象出现,因此,载荷下降现象主要由颈缩时的截面减小引起;高分子材料PC/ABS的屈服应力随环境温度的升高而降低。     

Large Strain Shear Compression Test of Sheet Metal Specimens

A hybrid experimental-computational procedure to establish accurate true stress-plastic strain curve of sheet metal specimen covering the large plastic strain region using shear compression test data is described. A new shear compression jig assembly with a machined gage slot inclined at 35° to the horizontal plane of the assembly is designed and fabricated. The novel design of the shear compression jig assembly fulfills the requirement to maintain a uniform volume of yielded material with characteristic maximum plastic strain level across the gage region of the Shear Compression Metal Sheet (SCMS) specimen. The approach relies on a one-to-one correlation between measured global load–displacement response of the shear compression jig assembly with SCMS specimen to the local stress-plastic strain behavior of the material. Such correlations have been demonstrated using finite element (FE) simulation of the shear compression test. Coefficients of the proposed correlations and their dependency on relative plastic modulus were determined. The procedure has been established for materials with relative plastic modulus in the range 5?×?10^?4?<?(E _p /E)?<?0.01. It can be readily extended to materials with relative plastic modulus values beyond the range considered in this study. Nonlinear characteristic hardening of the material could be established through piecewise linear consideration of the measured load–displacement curve. Validity of the procedure is established by close comparison of measured and FE-predicted load–displacement curve when the provisional hardening curve is employed as input material data in the simulation. The procedure has successfully been demonstrated in establishing the true stress-plastic strain curve of a demonstrator 0.0627C steel SCMS specimen to a plastic strain level of 49.2 pct.     

Lüders bands propagation of 1045 steel under multiaxial stress state

Inhomogeneous plastic deformation of 1045 steel under monotonic loading was experimentally studied. Thin-walled tubular specimens were used in the experiments and custom-made small strain gages were bonded on the specimen surface to characterize the local deformation. Experiments were conducted under tension, torsion, and combined tension–torsion. During the propagation of Lüders bands, the local deformation experienced two-stage deformation: an abrupt plastic deformation stage followed by a slower deformation process. In some area of the gage section of the specimen, a small amount of initial plastic deformation occurred before the Lüders front reached. During the propagation of Lüders bands, multiple Lüders fronts can be formed. Under tension, torsion, and combined tension–torsion with a constant axial load, the Lüders front was approximately parallel to the material plane of maximum shear stress. When the combined axial-torsion followed a proportional fashion, the stress–extensometer strain responses were dependent on the axial/torsional loading ratio, and the Lüders fronts were oriented differently and propagated along the specimen axis at a different velocity. The local strain was inhomogeneous even at the work-hardening stage. The relationships between the equivalent stress and the equivalent plastic strain were found to be practically identical for all the loading cases studied.     

A plane stress anisotropic plastic flow theory for orthotropic sheet metals

A phenomenological theory is presented for describing the anisotropic plastic flow of orthotropic polycrystalline aluminum sheet metals under plane stress. The theory uses a stress exponent, a rate-dependent effective flow strength function, and five anisotropic material functions to specify a flow potential, an associated flow rule of plastic strain rates, a flow rule of plastic spin, and an evolution law of isotropic hardening of a sheet metal. Each of the five anisotropic material functions may be represented by a truncated Fourier series based on the orthotropic symmetry of the sheet metal and their Fourier coefficients can be determined using experimental data obtained from uniaxial tension and equal biaxial tension tests. Depending on the number of uniaxial tension tests conducted, three models with various degrees of planar anisotropy are constructed based on the proposed plasticity theory for power-law strain hardening sheet metals. These models are applied successfully to describe the anisotropic plastic flow behavior of 10 commercial aluminum alloy sheet metals reported in the literature.     

An experimental study of inhomogeneous cyclic plastic deformation of 1045 steel under multiaxial cyclic loading

An experimental study was conducted on the inhomogeneous cyclic plastic deformation of 1045 steel under multiaxial cyclic loading. Thin-walled tubular specimens were used and small strain gages were bonded on the specimen surface to characterize the local deformation. The controlled loading paths included cyclic tension–compression, cyclic torsion, proportional axial-torsion, 90°-out-of-phase axial-torsion, and fully reversed torsion with a constant axial stress. The maximum stress in each experiment was lower than the lower yield stress of the material. It was found that the cyclic plastic deformation within the gage section of the specimen under multiaxial stress state followed the three-stage process that was observed from uniaxial loading, namely, incubation, propagation, and saturation. The plastic deformation was significantly inhomogeneous during the propagation stage, and the inhomogeneity continued through the saturation stage. The duration of each stage and the saturated strains were dependent on the cyclic stress amplitude and the loading path. Multiaxial stress state reduced the incubation stage. With identical equivalent stress magnitude, the nonproportional loading path resulted in the shortest incubation and propagation stages, and the saturated equivalent plastic strain magnitude was the smallest. Although the deformation over the gage section was inhomogeneous, the plastic deformation in a given local area was found to be practically isotropic.     

高分子材料平面应变拉伸变形局部化

将基于应变软化玻璃状高分子材料微观特征建立的ＢＰＡ８－链分子网络模型引入ＵｐｄａｔｉｎｇＬａｇｒａｎｇｅ有限元方法，建立了适于变形局部化分析的大变形弹塑性有限元驱动应力法．在此基础上，数值模拟了初始各向同性高分子材料平面应变拉伸变形局部化的传播过程．探讨了ＢＰＡ模型对具有加工硬化特性的结晶性高分子材料变形分析的适应性；分析了局部化传播过程中颈缩截面的非均匀应力三轴效应；最后，讨论了网格尺寸以及初始几何不均匀性对颈缩扩散以及应力三轴效应的影响     

Failure loads of spot weld specimens under impact opening and shear loading conditions

Failure loads of spot weld specimens are investigated under impact combined loading conditions. A set of test fixtures was designed and used to obtain failure loads of mild steel spot weld specimens under combined opening and shear loading conditions. Three different impact speeds were applied to examine the effects of separation speed on failure loads. Micrographs of the cross-sections of failed spot welds were obtained to understand the failure processes in mild steel specimens under different impact combined loads. The experimental results indicate that the failure mechanisms of spot welds are very similar for mild steel specimens at various impact speeds. These micrographs show that the sheet thickness can affect the failure mechanisms. For 1.0 mm specimens, the failure occurs near the base metal in a necking/shear failure mode. For 1.5 mm specimens, the failure occurs near the heat-affected zone in a shear failure mode. Based on the experimental results, the effects of the inertia force, the separation speed, and the loading angle on the failure loads of spot welds are investigated. Failure criteria are proposed to characterize the failure loads of spot welds under impact combined opening and shear loads for engineering applications. The failure load can be expressed as a function of the tensile strength of the base metal, the nugget size, the sheet thickness, the maximum separation speed, the loading angle, and empirical coefficients for a given welding schedule.     

Numerical analysis of diffuse and localized necking in orthotropic sheet metals

In the present paper the diffuse and localized necking models according to Swift [Swift, H.W., 1952. Plastic instability under plane stress, Journal of the Mechanics and Physics of Solids, 11–18], Hill [Hill, R., 1952. On discontinuous plastic states, with special reference to localized necking in thin sheets. Journal of the Mechanics and Physics of Solids 1, 19–30] and Marciniak and Kuczyński [Marciniak, Z., Kuczyński, K., 1967. Limit strains in the process of stretch-forming sheet metal. International Journal of Mechanical Sciences 9, 609–620], respectively, are considered. A theoretical framework for the mentioned models is proposed that covers rigid–plastic as well as elastic–plastic constitutive modelling using various advanced phenomenological yield functions that are able to account very accurately for plastic anisotropy. The mentioned necking models are applied to different orthotropic sheet metals in order to assess their predictive capabilities and to stress out some potential sources for discrepancies between simulations and experiments. In particular, the impact of the applied hardening curve and the equibiaxial r-value, which was recently introduced by Barlat [Barlat, F., Brem, J.C., Yoon, J.W., Chung, K., Dick, R.E., Choi, S.-H., Pourboghrat, F., Chu, E., Lege, D.J., 2003. Plane stress yield function for aluminium alloy sheets – part 1: theory. International Journal of Plasticity 19, 297–1319], on formability prediction is investigated. Furthermore, the impact of the Portevin–LeChatelier effect on the formability of aluminum sheet metals is discussed.     

金属材料平面应变拉伸变形局部化有限元分析

本文对于涉及韧性金属大变形中颈缩与剪切带断裂一类高度非线性变形局部化问题进行了弹塑性有限元数值模拟。采用改进的Ｊ２形变理论微分形式公式与交叉三角形四边形单元有限元网格，详细研究了应变硬化指数及初始表面不均匀特性的平面应变拉伸颈缩和剪切带形成的综合影响，给出此类问题的断裂机制图。     

韧性材料颈缩主应力面上应变分布假定的研究

为了深入研究韧性材料主应力面的应变分布情况，讨论Bridgman关于主应力面上应变均布假定的精度．本文首先结合断口学基本理论与在室温条件下拉伸断裂的Q235钢、40Cr钢和45#钢断口电子显微镜扫描结果，从微观角度分析其韧窝分布后发现应变均布假定存在一定的误差；然后基于体积守恒和Aramis三维应变观测系统测得的试验结果，将计算值和试验值进行对比分析发现，三种材料中除含碳量较高的45#钢外，应变均布假定并不适用于分析颈缩主应力面上应变分布．本文的研究成果可为进一步研究韧性材料颈缩大塑性阶段的应力、应变本构关系提供一定的参考．     

A combined necking and shear localization analysis for aluminum sheets under biaxial stretching conditions

A combined necking and shear localization analysis is adopted to model the failures of two aluminum sheets, AA5754 and AA6111, under biaxial stretching conditions. The approach is based on the assumption that the reduction of thickness or the necking mode is modeled by a plane stress formulation and the final failure mode of shear localization is modeled by a generalized plane strain formulation. The sheet material is modeled by an elastic-viscoplastic constitutive relation that accounts for the potential surface curvature, material plastic anisotropy, material rate sensitivity, and the softening due to the nucleation, growth, and coalescence of microvoids. Specifically, the necking/shear failure of the aluminum sheets is modeled under uniaxial tension, plane strain tension and equal biaxial tension. The results based on the mechanics model presented in this paper are in agreement with those based on the forming limit diagrams (FLDs) and tensile tests. When the necking mode is suppressed, the failure strains are also determined under plane strain conditions. These failure strains can be used as guidances for estimation of the surface failure strains on the stretching sides of the aluminum sheets under plane strain bending conditions. The estimated surface failure strains are higher than the failure strains of the forming limit diagrams under plane strain stretching conditions. The results are consistent with experimental observations where the surface failure strains of the aluminum sheets increase significantly on the stretching sides of the sheets under bending conditions. The results also indicate that when a considerable amount of necking is observed for a sheet metal under stretching conditions, the surface failure strains on the stretching sides of the sheet metal under bending conditions can be significantly higher.     

Modelling of the plastic flow of trip-aided multiphase steel based on an incremental mean-field approach

An incremental mean-field model is developed for the prediction of transformation induced plasticity (TRIP) in multiphase steel. The partitioning of strain between softer and harder constituents is computed based on an elastic-plastic Mori–Tanaka approach that accounts for the progressive transformation of austenite into martensite. The latter transformation is predicted using an energy-balance criterion that is formulated at the level of individual austenite grains. The model has been tested against experimental data. Macroscopic stress-strain curves and rate of martensite formation have been measured on sheet samples subjected to various loading modes: uniaxial tension, simple shear, and (in-plane) uniaxial compression. These experiments were performed at 20 °C and the uniaxial tensile test was repeated at ?30 °C. The mean-field model produces fair predictions of the macroscopic hardening resulting from TRIP on the condition that a sufficient proportion of the load is carried by the very hard martensite inclusions. Such prediction implies that one accounts for the stress heterogeneity across the ferrite-based matrix. At the same time, the model reproduces the elastic lattice strains and the plastic elongation which are measured within the phases by neutron diffraction and by image correlation in a scanning electron microscope, respectively. The model can be used in finite element simulations of forming processes which is illustrated in a study of necking of a cylindrical bar under uniaxial tension.