Direct synthesis of Nd3+ doped mesoporous TiO2 and investigation of its photocatalytic performance

Nd³⁺ doped mesoporous TiO₂ samples with different molar ratio of Nd/Ti were synthesized by a sol?Cgel method. The textural and optical properties of the samples were systematical characterized by X-ray diffraction, transmission electron microscopy, N₂ adsorption?Cdesorption isotherms, Fourier transform infrared spectroscopy and UV?CVisible absorbance spectroscopy. It was revealed that Nd³⁺ doping inhibited the phase transformation from anatase to rutile after calcination, and the mesoporous structure of doped samples was still retained with the increase of Nd/Ti molar ratio. The surface area of the samples varied from 137 to 210 m²g^?1 and the average pore size of them ranged between 5.7 and 8.2?nm. The photocatalytic activities of all the samples were evaluated by degradation methyl orange (MO) in aqueous solution as a model reaction under UV light irradiation. The results showed that the doped samples demonstrated a higher photocatalytic activity than the mesoporous TiO₂, and the 3?mol% Nd³⁺ doped mesoporous TiO₂ exhibited the best photocatalytic performance. Meanwhile, a promotion effect of the H₂O₂ added was verified in the degradation of MO.     

硼铈共掺杂纳米TiO2光催化降解三氯杀螨醇和菊酯类农药

采用溶胶-凝胶法在钛酸丁酯水解过程引入硼酸、硝酸铈,制备具有光催化活性的硼铈共掺杂纳米二氧化钛（TiO2）,经XRD、TEM、FT-IR、UV-Vis-DRS表征晶体结构,在日光灯照射下,光催化降解三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯农药。结果表明：硼铈共掺杂的TiO2只有锐钛矿型,而纯的或掺铈的TiO2有含有锐钛矿型、金红石相和少量板钛矿型,UV-Vis-DRS测定结果表明硼铈共掺杂的TiO2禁带宽度变小,硼铈共掺杂的TiO2在可见光区吸光度高于掺杂铈和不掺杂的TiO2,在420nm~850nm有强的吸收;在同样光照下对三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯的降解试验证明硼铈共掺杂纳米TiO2的光催化活性高于不掺杂或只掺杂铈的TiO2。     

Study on the formation of H2O2 on TiO2 photocatalysts and their activity for the photocatalytic degradation of X-GL dye

Titanium dioxide (TiO₂) nanoparticles of both anatase and rutile phases were synthesized by hydrothermal treatment of microemulsions, and their photocatalytic activity for the degradation of X-GL dye was investigated. The only difference between the two methods used was that different acids were added to the microemulsions to make a direct comparison of the photocatalytic activity of the polymorphs possible. UV — Vis reflectance and XRD spectroscopic investigations of these titanium dioxides indicated that a rutile structure could be formed (PR) when hydrochloric acid was used, and anatase formed (PA) when nitric acid was used. The activity of the two polymorphs and P-25 for the photocatalytic degradation of dye in water was also examined. It was found that P-25 consisting of anatase and rutile has the highest activity, and PR consisting of rutile has the lowest. Photodegradation of X-GL in the presence of these different TiO₂ particles under air-equilibrated controlled conditions led to the formation of hydrogen peroxide. The formation rate of H₂O₂ depended on the difference in crystalloid phase. These results indicate that the observed differences in the photocatalytic activity for the three TiO₂ photocatalysts are directly related to the formation rate of H₂O₂.     

Photocatalytic Activity for Water Decomposition to Hydrogen over Nitrogen‐doped TiO2 Nanoparticle

Nitrogen-doped TiO2 nanoparticle photocatalysts were obtained by an annealing method with gaseous ammonia and nitrogen. The influence of dopant N on the crystal structure was characterized by XRD, XPS, BET, TEM and UV-Vis spectra. The results of XRD indicate that, the crystal phase transforms from anatase to rutile structure gradually with increase of annealing temperature from 300 to 700 ℃. XPS studies indicate that the nitrogen atom enters the TiO2 lattice and occupies the position of oxygen atom. Agglomeration of particles is found in TEM images after annealing. BET results show that the specific surface areas of N-doped samples from 44.61 to 38.27 m2/g are smaller than that of Degussa TiO2. UV-Vis spectra indicate that the absorption threshold shifts gradually with increase of annealing temperature, which shows absorption in the visible region. The influence of annealing condition on the photocatalytic property has been researched over water decomposition to hydrogen, indicating that nitrogen raises the photocatalytic activity for hydrogen evolution, and the modified TiO2 annealed for 2 h at 400 ℃ under gas of NH3/N2 (V/V＝1/2) mixture shows better efficiency of hydrogen evolution. Furthermore, the N-doped TiO2 nanoparticle catalysts have obvious visible light activity, evidenced by hydrogen evolution under visible light (λ＞400 nm) irradiation. However, the catalytic activity under visible light irradiation is absent for Degussa as reference and the N-doped TiO2 annealed at 700 ℃.     

Li‐doped nanosized TiO2 powder with enhanced photocalatylic acivity under sunlight irradiation

This work reports on the synthesis of Li‐doped TiO₂ nanoparticles using the sol–gel process and solid‐state sintering, and investigates their potential use as a photocatalyst for degradation under sunlight excitation of different organic model compounds in aqueous solution. The structure of the nanocrystals was examined by X‐ray diffraction, UV‐vis ground state diffuse reflectance absorption spectra and X‐ray photoelectron emission spectroscopy. Results showed that samples prepared by sol–gel process and calcined at 400 °C are composed of a mixture of anatase and rutile phases, in contrast to the one prepared by solid‐state sintering, which exhibits an anatase phase with Li being involved in a spinel phase. The photocatalytic degradation of aqueous solutions of different aromatic compounds was successfully achieved under sunlight excitation in presence of Li‐doped TiO₂ prepared via sol–gel process. It was shown that the calcination temperature and the preparation mode greatly affect the photocatalytic efficiency. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis of W‐doped TiO2 by low‐temperature hydrolysis: Effects of annealing temperature and doping content on the surface microstructure and photocatalytic activity

A series of tungsten‐doped Titania photocatalysts were synthesized using a low‐temperature method. The effects of dopant concentration and annealing temperature on the phase transitions, crystallinity, electronic, optical, and photocatalytic properties of the resulting material were studied. The X‐ray patterns revealed that the doping delays the transition of anatase to rutile to a high temperature. A new phase W_yTi_1‐yO₂ appeared for 5.00 wt% W‐TiO₂ annealed at 900 °C. Raman and diffuse reflectance UV–Vis spectroscopy showed that band gap values decreased slightly up to 700 °C. X‐ray photoelectron spectroscopy showed that surface species viz. Ti³⁺, Ti⁴⁺, O^2?, oxygen‐vacancies, and adsorbed OH groups vary depending on the preparation conditions. The photocatalytic activity was evaluated via the degradation of methylene blue using LED white light. The degradation rate was affected by the percentage of dopants. The best photocatalytic activity was achieved with the sample labeled 5.00 wt% W‐TiO₂ annealed at 700 °C.     

Photocatalytic activity of nitrogen and copper doped TiO2 nanoparticles prepared by microwave-assisted sol-gel process

Cu and N-doped TiO₂ photocatalysts were synthesized from titanium (IV) isopropoxide via a microwave-assisted sol-gel method. The synthesized materials were characterized by X-ray diffraction, UV-vis diffuse reflectance, photoluminescence (PL) spectroscopy, SEM, TEM, FT-IR, Raman spectroscopy, photocurrent measurement technique, and nitrogen adsorption–desorption isotherms. Raman spectra and XRD showed an anatase phase structure. The SEM and TEM images revealed the formation of an almost spheroid mono disperse TiO₂ with particle sizes in the range of 9-17 nm. Analysis of N₂ isotherm measurements showed that all investigated TiO₂ samples have mesoporous structures with high surface areas. The optical absorption edge for the doped TiO₂ was significantly shifted to the visible light region. The photocurrent and photocatalytic activity of pure and doped TiO₂ were evaluated with the degradation of methyl orange (MO) and methylene blue (MB) solution under both UV and visible light illumination. The doped TiO₂ nanoparticles exhibit higher catalytic activity under each of visible light and UV irradiation in contrast to pure TiO₂. The photocatalytic activity and photocurrent ability of TiO₂ have been enhanced by doping of the titania in the following order: (Cu, N) - codoped TiO₂ > N-doped TiO₂ > Cu-doped TiO₂ > TiO₂. COD result for (Cu, N)-codoped TiO₂ reveals ∼92% mineralization of the MO dye on six h of visible light irradiation.     

Understanding the synergistic effects,optical and electronic properties of ternary Fe/C/S‐doped TiO2 anatase within the DFT + U approach

Although TiO₂ is an efficient photocatalyst, its large band gap limits its photocatalytic activity only to the ultraviolet region. An experimentally synthesized ternary Fe/C/S‐doped TiO₂ anatase showed improved visible light photocatalytic activity. However, a theoretical study of the underlying mechanism of the enhanced photocatalytic activity and the interaction of ternary Fe/C/S‐doped TiO₂ has not yet been investigated. In this study, the defect formation energy, electronic structure and optical property of TiO₂ doped with Fe, C, and S are investigated in detail using the density functional theory + U method. The calculated band gap (3.21 eV) of TiO₂ anatase agree well with the experimental band gap (3.20 eV). The defect formation energy shows that the co‐ and ternary‐doped systems are thermodynamically favorable under oxygen‐rich condition. Compared to the undoped TiO₂, the absorption edge of the mono‐, co‐, and ternary‐doped TiO₂ is significantly enhanced in the visible light region. We have shown that ternary doping with C, S, and Fe induces a clean band structure without any impurity states. Moreover, the ternary Fe/C/S‐doped TiO₂ exhibit an enhanced photocatalytic activity, a smaller band gap and negative formation energy compared to the mono‐ and co‐doped systems. Moreover, the band edges of Fe/C/S‐doped TiO₂ align well with the redox potentials of water, which shows that the ternary Fe/C/S‐doped TiO₂ is promising photocatalysts to split water into hydrogen and oxygen. These findings rationalize the available experimental results and can assist the design of TiO₂‐based photocatalyst materials.     

Photocatalytic activities of C–N-doped TiO2 nanotube array/carbon nanorod composite

A C–N-doped TiO₂ nanotube (NT)/carbon nanorod composite is fabricated by chemical vapor deposition (CVD). Carbon nanorods are grown from the TiO₂ NTs, and partly graphitized, while TiO₂ is in the mixture of anatase and rutile. The C–N doping shifts the absorption edge of TiO₂ NTs to the visible light region; the formed carbon nanorods promote the charge carrier transfer from the TiO₂ surface to the electrolyte. Under the simulated solar light irradiation, the C–N-doped TiO₂ NTs show higher photocatalytic activity in the degradation of methyl orange (MO) than the undoped TiO₂ NTs.     

Synthesis and Studies of the Visible‐Light Photocatalytic Properties of Near‐Monodisperse Bi‐Doped TiO2 Nanospheres

Near‐monodisperse Bi‐doped anatase TiO₂ nanospheres with almost uniform diameters in the range of 117 to 87 nm were prepared simply by introducing different amounts of bismuth nitrate pentahydrate into the reaction system and subsequent calcinations. X‐ray diffraction, UV‐visible diffuse reflectance spectra, and X‐ray photoelectron spectroscopy confirm that the doped ions substitute some of the lattice titanium atoms, and furthermore, Bi³⁺ and Bi⁴⁺ ions coexist. All the Bi‐doped TiO₂ samples show much better photocatalytic activity than pure TiO₂ in the degradation of rhodamine B (RhB) under the irradiation of visible light (λ>420 nm), and, interestingly, it was found that the degradation mechanism is different from the conventional one, which has already been reported elsewhere. The detailed mechanism is discussed in this article.     

Photodegradation of Rhodamine B on Sulfur Doped ZnO/TiO2 Nanocomposite Photocatalyst under Visible-light Irradiation

Sulfur doped ZnO/TiO₂ nanocomposite photocatalysts were synthesized by a facile sol‐gel method. The structure and properties of catalysts were characterized by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), UV‐vis diffusive reflectance spectroscopy (DRS) and N₂ desorption‐adsorption isotherm. The XRD study showed that TiO₂ was anatase phase and there was no obvious difference in crystal composition of various S‐ZnO/TiO₂. The XPS study showed that the Zn element exists as ZnO and S atoms form SO^2?₄. The prepared samples had mesoporosity revealed by N₂ desorption‐adsorption isotherm result. The degradation of Rhodamine B dye under visible light irradiation was chosen as probe reaction to evaluate the photocatalytic activity of the ZnO/TiO₂ nanocomposite. The commercial TiO₂ photocatalyst (Degussa P25) was taken as standard photocatalyst to contrast the prepared different photocatalyst in current work. The improvement of the photocatalytic activity of S‐ZnO/TiO₂ composite photocatalyst can be attributed to the suitable energetic positions between ZnO and TiO₂, the acidity site caused by sulfur doping and the enlargement of the specific area. S‐3.0ZnO/TiO₂ exhibited the highest photocatalytic activity under visible light irradiation after Zn amount was optimized, which was 2.6 times higher than P25.     

Photocatalytic degradation of organic compounds in aqueous systems by Fe and Ho codoped TiO<Subscript>2</Subscript>

Undoped, single-doped, and codoped TiO₂ nanoparticles were prepared by the sol-gel method and characterized with X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET)-specific surface area (S_BET), UV-Vis absorption spectra (UV-Vis), and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activity was evaluated by methyl orange (MO) degradation in an aqueous suspension under UV or simulated solar light illumination. XRD showed that all samples calcined at 600°C preserved the anatase structure, and doping inhibited the increase of crystallite size. The BET result revealed that doping improved the surface area of TiO₂. UV-Vis indicated that Fe³⁺-doping broadened the absorption profile of TiO₂. XPS demonstrated that doping was advantageous to absorb more surface hydroxyl groups or chemisorbed water molecules. Photocatalytic degradation showed that the photocatalytic activity of TiO₂ codoped with Fe³⁺ and Ho³⁺ ions was markedly improved. This was ascribed to the fact that there was a cooperative action in the two doped elements. Fe³⁺-doping broadens the absorption profile, improves photo utilization of TiO₂, and then generates more electronhole pairs. Ho³⁺-doping restrains the increase in grain size and retards the recombination of photo-generated electrons and holes.     

Comparison of optical and structural properties of nanostructure TiO2 thin film doped by Sn and Nb

The thin films of TiO₂ doped by Sn or Nb were prepared by sol–gel method under process control. The effects of Sn and Nb doping on the structural, optical and photo-catalytic properties of applied thin films have been studied by X-ray diffraction (XRD) high resolution transmission electron microscopy and UV–Vis absorption spectroscopy. Surface chemical state of thin films was examined by atomic X-ray photoelectron spectroscopy. XRD results suggest that adding impurities has a great effect on the crystallinity and particle size of TiO₂. Titania rutile phase formation in thin film was promoted by Sn⁴⁺ addition but was inhibited by Nb⁵⁺ doping. The activity of the photocatalyst was evaluated by photocatalytic degradation kinetics of aqueous methylene blue under UV and Visible radiation. The results show that the photocatalytic activity of the Sn-doped TiO₂ thin film have a larger degradation efficiency than Nb-doped TiO₂ under visible light, but under UV light photocatalytic activity of the Nb-doped TiO₂ thin film is better.     

Synthesis and Modification of Zn‐doped TiO2 Nanoparticles for the Photocatalytic Degradation of Tetracycline

The synthesis of Zn‐doped TiO₂ nanoparticles by solgel method was investigated in this study, as well as its modification by H₂O₂. The catalyst was characterized by transmission electron microscopy, X‐ray diffraction, Brunauer–Emmett–Teller, UV–visible reflectance spectra and X‐ray photoelectron spectroscopy (XPS). The results indicated that doping Zn into TiO₂ nanoparticles could inhibit the transformation from anatase phase to rutile phase. Zn existed as the second valence oxidation state in the Zn‐doped TiO₂. Zn‐doped TiO₂ that was synthesized by 5% Zn doping at 450°C exhibited the best photocatalytic activity. Then, the H₂O₂ modification further enhanced the photocatalytic activity. Zn doping and H₂O₂ modifying narrowed the band gap and efficiently increased the optical absorption in visible region. The optimal degradation rate of tetracycline by Zn‐doped TiO₂ and H₂O₂ modified Zn‐doped TiO₂ was 85.27% and 88.14%. Peroxide groups were detected in XPS analysis of H₂O₂ modified Zn‐doped TiO₂, favoring the adsorption of visible light. Furthermore, Zn‐doped TiO₂ modified by H₂O₂ had relatively good reusability, exhibiting a potential practical application for tetracycline's photocatalytic degradation.     

High temperature stability and photocatalytic activity of nanocrystalline anatase powders with Zr and Si co-dopants

TiO₂ nanopowders doped by Si and Zr were prepared by sol–gel method. The effects of Si and Zr doping on the structural, optical, and photo-catalytic properties of titania nanopowders have been studied by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy, and UV–Vis absorption spectroscopy. XRD results suggest that adding impurities has a significant effect on anatase phase stability, crystallinity, and particle size of TiO₂. Titania rutile phase formation in ternary system (Ti–Si–Zr) was inhibited by Zr⁴⁺ and Si⁴⁺ co-doped TiO₂ in high temperatures (500–900 °C) and 36 mol% anatase composition is retained even after calcination at 1,000 °C. The photocatalyst activity was evaluated by photocatalytic degradation kinetics of aqueous methylen orange under visible radiation. The results show that the photocatalytic activity of the 20 %Si and 15 %Zr co-doped TiO₂ nanopowders have a larger degradation efficiency than pure TiO₂ under visible light.     

Photocatalytic activity of polyaniline/Fe-doped TiO2 composites by in situ polymerization method

This study was focused on the photocatalytic activity of polyaniline (Pani)/iron doped titanium dioxide (Fe–TiO₂) composites for the degradation of methylene blue as a model dye. TiO₂ nanoparticles were doped with iron ions (Fe) using the wet impregnation method and the doped nanoparticles were further combined with Pani via an in situ polymerization method. For comparison purposes, Pani composites were also synthesized in the presence undoped TiO₂. The photocatalyst and the composites were characterized by standard analytical techniques such as FTIR, XRD, SEM, EDX and UV–Vis spectroscopies. Fe–TiO₂ and its composites exhibited enhanced photocatalytic activity under ultraviolet light irradiation. Improved photocatalytic activity of Fe–TiO₂ was attributed to the dopant Fe ions hindering the recombination of the photoinduced charge carriers. Pani/Fe–TiO₂ composite with 30?wt.% of TiO₂ nanoparticles achieved 28% dye removal and the discoloration rate of methylene blue for the sample was 0.0025?min^?1. FTIR, XRD, SEM, EDX and UV–Vis spectroscopies supported the idea that Fe ions integrated into TiO₂ crystal structure and Pani composites were successfully synthesized in the presence of the photocatalyst nanoparticles. The novelty of this study was to investigate the photocatalytic activity of Pani composites, containing iron doped TiO₂ and to compare their results with that of Pani/TiO₂.     

Two‐Dimensional Hollow TiO2 Nanoplates with Enhanced Photocatalytic Activity

Two‐dimensional anatase TiO₂ hollow nanoplates were firstly synthesized through a facile synthesis route by using α‐Fe₂O₃ nanoplates as removable templates. Two‐dimensional hollow TiO₂ nanoplates with different ratios of anatase and rutile phases were obtained by adjusting the calcining temperature. The average diameters were around 600 nm, and the shell thickness was approximately 30 nm. The photocatalytic performance of TiO₂ was investigated by decomposing rhodamine B under simulated sunlight. Among the TiO₂ samples, the anatase TiO₂ hollow nanoplates manifested a significant enhancement in the photocatalytic performances. The excellent catalytic performance can be attributed to the unique structure of the two‐dimensional anatase TiO₂ hollow nanoplates, including a large surface area and increased dye–photocatalyst contact areas as well as more active sites for photodegradation.     

Synthesis,Characterization and Photocatalytic Behavior of SiO2@nitrized-TiO2 Nanocomposites Obtained by a Straightforward Novel Approach

We report on the facile synthesis of SiO₂@nitrized-TiO₂ nanocomposite (NST) by calcination of TiO₂ xerogel with OctaAmmonium POSS® (N-POSS; POSS=polyhedral oligomeric silsesquioxanes). The as-obtained nanoporous mixed oxide is constituted by uniformly distributed SiO₂ and nitrized-TiO₂, where the silica component is present in an amorphous state and TiO₂ in an anatase/rutile mixed phase (92.1 % vs. 7.9 %, respectively) with very small anatase crystallites (3.7 nm). The TiO₂ lattice is nitrized both at interstitial and substitutional positions. NST features a negatively charged surface with a remarkable surface area (406 m² g⁻¹), endowed with special adsorption capabilities towards cationic dyes. Its photocatalytic behavior was tested by following the degradation of standard aqueous methylene blue and methyl orange solutions under UV and visible light irradiation, according to ISO 10678:2010. For comparison, analogous investigations were carried out on a silica-free N−TiO₂, obtained by using NH₄Cl as nitrogen source.     

Carbon-doped anatase TiO2 nanotube array/glass and its enhanced photocatalytic activity under solar light

To enhance the photocatalytic activity under solar light, highly ordered TiO₂ nanotube arrays (TNAs) film with anatase phase was fabricated on glass and successfully doped with carbon at various temperatures of 450–550 °C. The characterization results indicate that, after carbon doping, the TNAs still remained nanotubular structure with anatase phase. But their optical response shifted from UV to the visible light region and the recombination of photogenerated carriers was suppressed effectively. It is more important that the carbon-doped TNAs/glass (C-TNAs) samples exhibited high solar light photocatalytic activity, and 68%, 61% and 56% MO was photodegraded in 150 min by the C-TNAs calcined at 550, 500 and 450 °C, respectively. Especially, the apparent reaction rate constant of C-TNAs calcined at 550 (k, 0.065 min⁻¹) with the highest activity is 3.6 times that of pristine anatase TNAs (k, 0.018 min⁻¹). It is clear that carbon doping enhanced the photocatalytic activity under sunlight at optimized annealing temperature. The efficient activity could be attributed to the synergetic effects of strong visible light absorption, good crystallization, large surface, and enhanced separation of photoinduced carriers.     

Coal Combustion Synthesis of Coal Cinder-Supported TiO<Subscript>2</Subscript> with Commendable Photocatalytic Activity

Coal cinder-supported TiO₂ photocatalysts were synthesized via a novel coal combustion method. As-obtained samples were characterized by XRD, SEM, EDS mapping, Raman spectra, FTIR and DRS, and their photocatalytic performances were evaluated by degradation of methylene blue (MB) and methyl orange (MO) under UV–Vis light illumination. The results revealed that mixed-phases TiO₂ with adjustable anatase–rutile ratio could be obtained by adjusting the amount of precursor tetrabutyl titanate, which was uniformly covered on the coal cinder. These coal cinder-supported TiO₂ photocatalysts exhibited commendable photocatalytic activity. Among them, the indexed CCT-7.5 sample presented the maximum of activity, which can be attributed to the optimal phase composition of TiO₂. The present work provided a novel synthetic route to fabricate immobilized photocatalysts, which might be extended to the preparation of other functional materials.