Preparation of titania hollow spheres by catalyst-free hydrothermal method and their high thermal stabilities

TiO₂ hollow spheres have been prepared by hydrothermal method using carbon spheres as hard templates based on template-directed deposition and calcination in order to remove templates. The morphology and structure of samples were systematically characterized by using various techniques, including XRD, zeta analyzer, SEM, TEM, DRS and FTIR. In this approach, the anatase phase was retained for temperatures up to 900 °C. Moreover, negative charged titania is deposited onto the negative charged surface of carbon spheres, which is proved by nanoparticle size analyzer. Therefore, a possible formation mechanism of TiO₂ hollow spheres was proposed. TiO₂ hollow spheres calcined at 550 °C exhibited the superior photocatalytic activity for the degradation of Rhodamine B, 2.9 times greater than that of Degussa P25. Furthermore, thermal stability of TiO₂ hollow spheres was examined. Fortunately, we found that hollow structures could still be visible distinctly after calcining at 900 °C.     

Effect of calcination temperature on porous titania prepared from industrial titanyl sulfate solution

Porous titania with anatase phase was prepared via thermal hydrolysis of industrial titanyl sulfate solution, and subsequent calcination at different temperature. The as-prepared powders were characterized by TG, DSC, XRD, particle size distribution test, N₂ adsorption-desorption isotherm and SEM. Raising calcination temperature could accelerate the crystal growth, enlarge its specific surface area, pore diameter, and improve its photocatalytic activity. While too high temperature could destroy the pore structure even collapse. The optimal calcination temperature is 550 °C, and the obtained sample showed good thermal stability and high photocatalytic activity, with specific surface area of 189.3 m²/g and higher degree of crystallinity, and its photocatalytic degradation rate of methylene blue was of 95.76%.     

A one-pot method to prepare N-doped titania hollow spheres with high photocatalytic activity under visible light

N-doped titania hollow spheres (NTHS) were prepared by a one-pot hydrothermal method using urea as precursor of nitrogen. The prepared hollow spheres were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS) and UV-vis diffuse reflectance spectrum (DRS). The photocatalytic activity of as-prepared titania hollow spheres was determined by degradation of Reactive Brilliant Red dye X-3B (C.I. reactive red 2) under visible light irradiation, and was compared to non-doped titania hollow spheres and commercial P25 titania. Results indicated that the as-prepared NTHS showed highest photocatalytic activity.     

Fabrication of porous BaSnO3 hollow architectures using BaCO3@SnO2 core-shell nanorods as precursors

We present a strategy to synthesize porous BaSnO₃ hollow architectures with that were 150-300 nm in diameter and 1.5-5 μm in length using precursor of BaCO₃@SnO₂ nanorods prepared by hydrothermal treatment. BaCO₃@SnO₂ nanorods, consisting of a BaCO₃ core and a SnO₂ shell, could be used effectively for the solid-state synthesis of polycrystalline BaSnO₃ powder at 800 °C (lower than convention for BaCO₃ and SnO₂ mixtures). The core/shell structure of the precursor could play a role as a structural directing template for preparing BaSnO₃ hollow architectures during the calcination process. The X-ray diffractometer (XRD), scanning electron microscope (SEM), and transmission electron microscope (TEM) are employed to characterize the structures and morphologies. When applied to DSSC, the porous BaSnO₃ hollow architectures exhibit distinct photovoltaic effect.     

Preparation, characterization and photocatalytic activity of the neodymium-doped TiO2 hollow spheres

Nd-doped titania hollow spheres were prepared using carbon spheres as template and Nd-doped titania nanoparticles as building blocks. The Nd-doped titania nanoparticles were synthesized at low temperature. The prepared hollow spheres were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS) and UV-vis diffuse reflectance spectrum (DRS). The effects of Nd content on the physical structure and photocatalytic activities of doped titania hollow sphere samples were investigated. Results showed that there was an optimal Nd-doped content (3.9 at.%) for the photocatalytic degradation of dye X-3B (C.I. Reactive Red 2). The apparent rate constant of the best one was almost 9 times as that of P25 titania. The mechanism of photocatalytic degradation of dyes under visible light irradiation was also discussed.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

Anatase type titania nanotube arrays direct fabricated by anodization without annealing

In this paper, anatase type titania nanotube arrays were direct fabricated by anodization in dimethyl sulfoxide electrolyte containing 1 wt% HF solution at above 50 °C without subsequently annealing. The length of the nanotubes decreases with increasing anodization temperature from about approximately 15 μm at 40 °C to approximately 4.5 μm at 60 °C. High resolution transmission electron microscope images and selected area electron diffraction pattern confirm the polycrystalline anatase specimen consisting of many nanocrystals with a random orientation.     

Influence of high temperature annealing on the structure, hardness and tribological properties of diamond-like carbon and TiAlSiCN nanocomposite coatings

Diamond-like carbon (DLC) and TiAlSiCN nanocomposite coatings were synthesized and annealed at different temperatures in a vacuum environment. The microstructure, hardness and tribological properties of as-deposited and annealed DLC-TiAlSiCN nanocomposite coatings were characterized by X-ray diffraction, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), Raman spectroscopy, nano-indentation and friction tests. The TEM results reveal that the as-deposited DLC-TiAlSiCN coating has a unique nanocomposite structure consisting of TiCN nanocrystals embedded in an amorphous matrix consisting of a-Si₃N₄, a-SiC, a-CN and DLC, and the structure changed little after annealing at 800 °C. However, XPS and Raman results show that an obvious graphitization of the DLC phase occurred during the annealing process and it worsened with annealing temperature. Because of the graphitization, the hardness of the DLC-TiAlSiCN coating after annealing at 800 °C decreased from 45 to 36 GPa. In addition, the DLC-TiAlSiCN coating after annealing at 800 °C has a similar friction coefficient to the as-deposited coating.     

Synthesis of porous hollow silica spheres using polystyrene-methyl acrylic acid latex template at different temperatures

Porous hollow silica spheres were prepared by using polystyrene-methyl acrylic acid latex as a template and cetyltrimethylammonium bromide as a wall structure-directing agent starting from tetraethoxysilane. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), FT-infrared spectroscopy (FT-IR) and nitrogen adsorption/desorption were used to characterize the hollow silica spheres. When silica-coated latex composites were prepared at room temperature, hollow silica spheres with micropores in the walls were formed after removing the latex templates by calcination. When silica-coated latex composites were aged at a higher temperature of 150 °C, intact mesoporous hollow silica spheres were formed after calcination treatment.     

Synthesis of ZnO-SnO2 composite oxides by CTAB-assisted co-precipitation and photocatalytic properties

ZnO-SnO₂ composite oxides with various molar ratios of Sn:Zn have been synthesized at different calcination temperatures via a facile cetyltrimethylammonium bromide (CTAB)-assisted co-precipitation method with Zn(NO₃)₂·6H₂O and SnCl₄·5H₂O as starting materials. XRD, TEM, SEM and BET were employed to characterize the as-prepared samples. It has been found that amorphous intermediates appear between the evolutions of ZnO and SnO₂ crystals. The photocatalytic properties of the composite oxides were investigated using photocatalytic degradation of methyl orange as the probe reaction. The results show that the ZnO-SnO₂ composite oxide with a cube morphology exhibits the best photocatalytic activity, which was prepared with a molar ratio of Zn:Sn of 2:1 and calcination temperature of 700 °C.     

Stability and textural properties of cobalt incorporated MCM-48 mesoporous molecular sieve

Transition metal cobalt incorporated MCM-48 mesoporous molecular sieves (CoMCM-48) with different Co contents were synthesized hydrothermally at 120 °C for 24 h by directly adding fluoride ions to the initial gel. The resulting materials were characterized by means of XRD, TEM, FT-IR, UV-vis, TPR and N₂ physical adsorption, respectively. The effect of various factors, such as the Si/Co molar ratio, calcination temperature and hydrothermal treatment time, on the crystalline structure and textural properties of CoMCM-48 was investigated in detail. The results show that the CoMCM-48 mesoporous materials with high specific surface area were successfully synthesized. A small amount substitution of Co for Si in MCM-48 did not significantly change the textural properties while the higher cobalt incorporated leads to decrease of the surface area and deterioration of structural regularity. Furthermore, the resulting CoMCM-48 still retained the cubic mesoporous framework even after calcination at 800 °C for 4 h or hydrothermal treatment at 100 °C for 24 h.     

Hydrothermal preparation and photoluminescent properties of MgAl2O4: Eu spinel nanocrystals

Nanoplates of the MgAl₂O₄ spinel doped with Eu³⁺ ions were prepared by a microwave assisted hydrothermal method. Structural properties of the precursor calcined at 700 and 1000 ^oC powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). According to the obtained XRD patterns the formation of single-phase spinels after calcination was confirmed. The average spinel particle size was determined to be 11 nm after calcination at 700 °C and it increased up to 14 nm after calcination at 1000 °C. The photoluminescent properties of prepared powders with different Eu³⁺ ion concentrations (0-5% mol) were investigated using excitation and emission spectroscopy at room and low temperatures (77 K).     

Facile synthesis and characterization of glass/cobalt core/shell composite spheres with tunable shell morphologies

Polyhedral cobalt microcrystals assembled on hollow glass spheres are successfully synthesized by a facile and easy-control hydrothermal reduction process, and thus hierarchical glass/cobalt core/shell composite hollow spheres are fabricated with low-density (0.96 g cm⁻³). By properly tuning the process conditions and the component of the reaction solution, a series of composite spheres with gradient in morphologies of the shell layer can be prepared. Based on a series of contrast experiments, the probable formation mechanism of the core/shell hierarchical structures is proposed. The magnetic properties of the products are studied and the results demonstrate that the composite spheres present ferromagnetic properties related to the special shell morphologies. The composite hollow spheres thus obtained may have some promising applications in the fields of low-density magnetic materials, conduction, and catalysis, etc. This work provides an additional strategy to prepared core/shell composite spheres with tailored shell morphology and magnetic properties.     

Crystallinity effect in the textural properties of titania-TPA catalysts

Catalysts based in titania mixed with tungstophosphoric acid (TPA), H₃PW₁₂O₄₀, in various proportions (1, 15, 25 and 50 wt%) were obtained by the sol-gel method. The gels were prepared by hydrolysis and gellation of titanium n-butoxide with a TPA solution, using HNO₃ as a catalyst to obtain a pH 3. Fresh samples were thermally treated from 100 to 800 °C, in a stepwise increment of 100 °C during 20 h per step. Specific surface areas were calculated by the BET method from the nitrogen adsorption isotherms; it was found that the surface area increased with TPA content. The crystallization behavior was followed by powder X-ray diffraction. Crystallite size measurements showed that anatase remains nanocrystalline in the studied temperature range. From the X-ray data, it was clear that below 700 °C TPA is highly dispersed in an amorphous state.     

Effect of post heat treatment on microstructure and photocatalytic activities of TiO2 nanoribbons

Low-dimensional TiO₂ nanoribbons were synthesized by a simple one-step hydrothermal method. The TiO₂ nanoribbons were calcined over the temperature range 200-800 °C in order to enhance their photocatalytic properties by altering their crystal phase and increasing crystallization. Effects of hydrothermal temperature, calcinated temperature and calcination time on the formation of nanostructures have been observed and characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The (BET) specific surface area of the samples which with different post treatments were determined by N₂ absorption-desorption experiment. In addition, photocatalytic activities of the nanoribbons were evaluated by photodegradation of organic dyes methyl orange under the radiation of UV light. The results reveal that the post-treatments have great effects on the microstructures and the photocatalytic activities of TiO₂ nanoribbons.     

Structure and photocatalytic properties of copper-doped rutile TiO2 prepared by a low-temperature process

Copper-doped titania with variable Cu/Ti ratios have been prepared via a simple aqueous-phase method at 85 °C. The obtained products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and UV-vis absorption spectra analysis. The photocatalytic properties of the products were tested by photocatalytic degradation of aqueous brilliant red X-3B solution. The results showed that the sample with 2% copper doping has the best photocatalytic activity, which is 3 times that of undoped rutile titania. The effect of the doped copper on the structure and property of TiO₂ has also been discussed.     

Study on the surface erosion route to the fabrication of TiO2 hollow spheres

Three-dimensional (3D) architecture of TiO₂ hollow sphere has many excellent and interesting performances that attract significant attention nowadays. In this paper, a simple surface erosion approach to the fabrication of TiO₂ hollow spheres via the hydrothermal process has been developed. The morphologies and the phase were characterized by scanning electron microscopy (SEM) and X-ray diffractometer (XRD). The results indicate that the anatase-type TiO₂ hollow spheres with a diameter of ∼1 μm are successfully synthesized. The shell thickness of TiO₂ hollow spheres is ∼150 nm and the size of hollow cavity is ∼600 nm. By the control experiments, the influence of ammonium fluoride and hydrogen peroxide on the hollow spherical structures was studied. Hydrogen peroxide acts as both the oxidant and the bubble generator, ammonium fluoride is crucial for the erosion and dissolution of titanium, the detailed dissolution-crystallization mechanism for the formation of TiO₂ hollow spheres was also proposed.     

Synthesis of samarium- and nitrogen-co-doped TiO2 by modified hydrothermal method and its photocatalytic performance for the degradation of 4-chlorophenol

Sm- and nitrogen-co-doped TiO₂ (Sm-N-TiO₂) catalysts were prepared via the modified hydrothermal method using tetrabutyl titanate as the precursor and calcination at 200 °C. The microstructure of the sample was characterized by X-ray diffraction (XRD), ultraviolet-visible diffuse reflection spectroscopy (UV-vis-DRS), Fourier transform infrared (FTIR) spectra and X-ray photoelectron spectroscopy (XPS). The average particle size was ca. 16.0 nm as calculated from XRD patterns. Sm-N-TiO₂ nanocrystalline showed strong visible-light response and high photocatalytic activity for 4-chlorophenol degradation under irradiation by visible-light (400-500 nm). The high visible-light photocatalytic activity of the obtained Sm-N-TiO₂ might result from the incorporation of nitrogen atoms in TiO₂, which extended the spectral response to the visible region, and Sm₂O₃ facilitated the excited electron transfer and hence suppressed efficiently the recombination of photoproduced electron-hole.     

Low temperature synthesis of TiO2−xNy powders and films with visible light responsive photocatalytic activity

Nitrogen-doped titania powders and films with excellent visible light photocatalytic activity were successfully prepared by an unadulterated ‘low-temperature process’ below 60 °C using mechanochemical doping and oxygen plasma treatment.     

Properties of mesoporous tungstosilicic acid/titania composites prepared by sol-gel method

The tungstosilicic acid/titania composites were prepared by the sol-gel method. Titanium isopropoxide was used as titania precursor, and urea as a low-cost template. The tungstosilicic acid (TSA) was added in the same step as that in which titania hydrogel is formed. The TSA-modified samples only showed the characteristic peaks of anatase phase of titanium oxide in the XRD patterns, indicating that the presence of TSA retarded the crystallization of the anatase phase and its transformation into the rutile phase. Spherical particles with sizes between 200 and 700 nm, formed by aggregation of nanoparticle aggregates (4-50 nm in size), were observed. The particle size increased when the TSA content was raised and also increased slightly with the thermal treatment temperature. Mesoporous materials were obtained, with a mean pore diameter higher than 3.1 nm. Both the increase of the TSA concentration in the solid and the calcination temperature led to a decrease in the specific surface area of the samples. The main heteropolyoxometallate species present in the composites is the [SiW₁₂O₄₀]⁴⁻ anion for the composites calcined up to 500 °C. The band gap energy decreased as a result of the introduction of TSA into the titania matrix, though it remained almost constant with the calcination temperature increase.