Silane treatment of Fe3O4 and its effect on the magnetic and wear properties of Fe3O4/epoxy nanocomposites

In this study, the effect of silane treatment of Fe₃O₄ on the magnetic and wear properties of Fe₃O₄/epoxy nanocomposites was investigated. Fe₃O₄ nanopowders were prepared by coprecipitation of iron(II) chloride tetrahydrate with iron(III) chloride hexahydrate, and the surfaces of Fe₃O₄ were modified with 3-aminopropyltriethoxysilane. The magnetic properties of the powders were measured on unmodified and surface-modified Fe₃O₄/epoxy nanocomposites using SQUID magnetometer. Wear tests were performed on unmodified and surface-modified Fe₃O₄/epoxy nanocomposites under the same conditions (sliding speed: 0.18 m/s, load: 20 N).The results showed that the saturation magnetization (M_s) of surface-modified Fe₃O₄/epoxy nanocomposites was approximately 110% greater than that of unmodified Fe₃O₄/epoxy nanocomposites. This showed that the specific wear rate of surface-modified Fe₃O₄/epoxy nanocomposites was lower than that of unmodified Fe₃O₄/epoxy nanocomposites. The decrease in wear rate and the increase in magnetic properties of surface-modified Fe₃O₄/epoxy nanocomposites occurred due to the improved dispersion of Fe₃O₄ into the epoxy matrix.     

In situ growth of sol–gel-derived nano-VO2 film and its phase transition characteristics

Fe₃O₄/C nanocomposites have been prepared by one-pot PEG-assisted co-precipitation method. The structure and morphology of the as-prepared materials were analyzed by X-ray diffraction and transmission electron microscopy. The results showed that Fe₃O₄/C nanocomposites were well crystallized. Carbon nanoparticles dispersed among Fe₃O₄ particles forming a carbon layer, which prevent Fe₃O₄ particles from contacting each other. Electrochemical performance tests showed that Fe₃O₄/C nanocomposites keep at a high discharge capacity of 902.4 mAh g^?1 at 1 C after 110 cycles. Furthermore, the samples showed much improved rate capability and better cycle stability compared with pure Fe₃O₄. The excellent electrochemical performance of Fe₃O₄/C nanocomposites can be attributed to unique nanostructure and existence of amorphous carbon in the composites. The existence of the amorphous carbon not only enhanced electric conductivity, but also buffered volume variation of Fe₃O₄/C nanocomposites during charge/discharge process.     

Electrostatic self-assembly of Fe3O4 nanoparticles on carbon nanotubes

Carbon nanotubes (CNTs)-based magnetic nanocomposites can find numerous applications in nanotechnology, integrated functional system, and in medicine owing to their great potentialities. Herein, densely distributed magnetic Fe₃O₄ nanoparticles were successfully attached onto the convex surfaces of carbon nanotubes (CNTs) by an in situ polyol-medium solvothermal method via non-covalent functionalization of CNTs with cationic surfactant, cetyltrimethylammonium bromide (CTAB), and anionic polyelectrolyte, poly(sodium 4-styrenesulfonate) (PSS), through the polymer-wrapping technique, in which the negatively charged PSS-grafted CNTs can be used as primer for efficiently adsorption of positively metal ions on the basis of electrostatic attraction. X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) analysis have been used to study the formation of Fe₃O₄/CNTs. The Fe₃O₄/CNTs nanocomposites were proved to be superparamagnetic with saturation magnetization of 43.5 emu g^?1. A mechanism scheme was proposed to illustrate the formation process of the magnetic nanocomposites.     

Sonochemical fabrication of Fe3O4 nanoparticles on reduced graphene oxide for biosensors

This study synthesized Fe₃O₄ nanoparticles of 30–40 nm by a sonochemical method, and these particles were uniformly dispersed on the reduced graphene oxide sheets (Fe₃O₄/RGO). The superparamagnetic property of Fe₃O₄/RGO was evidenced from a saturated magnetization of 30 emu/g tested by a sample-vibrating magnetometer. Based on the testing results, we proposed a mechanism of ultrasonic waves to explain the formation and dispersion of Fe₃O₄ nanoparticles on RGO. A biosensor was fabricated by modifying a glassy carbon electrode with the combination of Fe₃O₄/RGO and hemoglobin. The biosensor showed an excellent electrocatalytic reduction toward H₂O₂ at a wide, linear range from 4 × 10^?6 to 1 × 10^?3 M (R² = 0.994) as examined by amperometry, and with a detection limit of 2 × 10^?6 M. The high performance of H₂O₂ detection is attributed to the synergistic effect of the combination of Fe₃O₄ nanoparticles and RGO, promoting the electron transfer between the peroxide and electrode surface.     

Facile Synthesis of Gd(OH)3‐Doped Fe3O4 Nanoparticles for Dual‐Mode T1‐ and T2‐Weighted Magnetic Resonance Imaging Applications

The facile hydrothermal synthesis of polyethyleneimine (PEI)‐coated iron oxide (Fe₃O₄) nanoparticles (NPs) doped with Gd(OH)₃ (Fe₃O₄‐Gd(OH)₃‐PEI NPs) for dual mode T₁‐ and T₂‐weighted magnetic resonance (MR) imaging applications is reported. In this approach, Fe₃O₄‐Gd(OH)₃‐PEI NPs are synthesized via a hydrothermal method in the presence of branched PEI and Gd(III) ions. The PEI coating onto the particle surfaces enables further modification of poly(ethylene glycol) (PEG) in order to render the particles with good water dispersibility and improved biocompatibility. The formed Fe₃O₄‐Gd(OH)₃‐PEI‐PEG NPs have a Gd/Fe molar ratio of 0.25:1 and a mean particle size of 14.4 nm and display a relatively high r₂ (151.37 × 10^?3m ^?1 s^?1) and r₁ (5.63 × 10^?3m ^?1 s^?1) relaxivity, affording their uses as a unique contrast agent for T₁‐ and T₂‐weighted MR imaging of rat livers after mesenteric vein injection of the particles and the mouse liver after intravenous injection of the particles, respectively. The developed Fe₃O₄‐Gd(OH)₃‐PEI‐PEG NPs may hold great promise to be used as a contrast agent for dual mode T₁‐ and T₂‐weighted self‐confirmation MR imaging of different biological systems.     

Synthesis and characterization of “mulberry”-like Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/multiwalled carbon nanotube nanocomposites

Nanocomposites composed of multi-wall carbon nanotubes (MWNTs) and Fe₃O₄ nanoparticles were fabricated using solvothermal method. Transmission and scanning electron microscopy, energy dispersive spectroscopy, and X-ray powder diffraction measurements confirmed that these mulberry-like Fe₃O₄ microparticles which were combined with the MWNTs in a random pattern are constructed with tiny nanocrystallites (12 nm in average diameter). The magnetic properties of the Fe₃O₄/MWNTs nanocomposites were measured using a vibrating sample magnetometer. Results showed that the Fe₃O₄/MWNTs nanocomposites exhibited superparamagnetism at room temperature and possessed a lower saturation magnetization (around 27.6 emu/g) than that of the pure Fe₃O₄ nanoparticles (around 33.7 emu/g). The Fe₃O₄/MWNTs nanocomposites have potential applications in engineering and medicine.     

Facile Synthesis of Lactobionic Acid‐Targeted Iron Oxide Nanoparticles with Ultrahigh Relaxivity for Targeted MR Imaging of an Orthotopic Model of Human Hepatocellular Carcinoma

Development of multifunctional nanoprobes for tumor diagnosis is extremely important in the field of molecular imaging. In this study, the facile synthesis of lactobionic acid (LA)‐targeted superparamagnetic iron oxide (Fe₃O₄) nanoparticles (NPs) with ultrahigh relaxivity for targeted magnetic resonance (MR) imaging of an orthotopic hepatocellular carcinoma (HCC) is reported. Polyethyleneimine (PEI)‐stabilized Fe₃O₄ NPs prepared via a mild reduction route are sequentially coupled with fluorescein isothiocyanate and polyethylene glycol‐LA (LA‐PEG‐COOH) segment, followed by acetylation of the remaining PEI surface amines. The formed LA‐targeted Fe₃O₄ NPs are thoroughly characterized. It is shown that the developed multifunctional LA‐targeted Fe₃O₄ NPs are colloidally stable and water‐dispersible, display an ultrahigh r ₂ relaxivity (579.89 × 10^?3 m ^?1 s^?1) and excellent hemocompatibility and cytocompatibility in the given concentration range, and can target HepG2 cells overexpressing asialoglycoprotein receptors as confirmed by in vitro cellular uptake assay, flow cytometry, and confocal microscopy. Most strikingly, the developed multifunctional LA‐targeted Fe₃O₄ NPs can be used as a nanoprobe for targeted MR imaging of HepG2 cells in vitro and an orthotopic tumor model of HCC in vivo. With the ultrahigh r ₂ relaxivity and the versatile PEI amine‐mediated conjugation chemistry, a range of different Fe₃O₄ NP‐based nanoprobes may be developed for theranostics of different types of cancer.     

Preparation and characterization of bifunctional, Fe3O4/ZnO nanocomposites and their use as photocatalysts

Bifunctional magnetic-optical Fe₃O₄/ZnO nanocomposites with different molar ratio were successfully synthesized by a facile two-step strategy. Compared with the other methods, it was found to be mild, inexpensive, green, convenient and efficient. Fe₃O₄ nanocrystal was used as seed for the deposit and growth of ZnO nanoparticle. A series of the characterizations manifested that the combination of Fe₃O₄ with ZnO nanoparticles was successful. Photocatalytic activity studies confirmed that as-prepared nanocomposites had excellent photodegradating behavior to Methyl Orange (MO) compared to the pure ZnO nanoparticles. The results showed that the degradation percentage of MO was about 93.6% for 1 h when the amount of catalyst was 0.51 g L⁻¹ and initial concentration of MO was 6 × 10⁻⁵ mol L⁻¹ in the pH 7 solution. Moreover, the kinetics of photocatalytic degradation reaction could be expressed by the first-order reaction kinetic model. Furthermore, the Fe₃O₄/ZnO nanocomposites could be also served as convenient recyclable photocatalysts because of their magnetic properties.     

Synthesis of Fe3O4@LaF3:Ce,Tb nanocomposites with bright fluorescence and strong magnetism

In this paper, fluorescent-magnetic Fe₃O₄@LaF₃:Ce,Tb nanocomposites were synthesized by combining fluorescent LaF₃:Ce,Tb and magnetic Fe₃O₄ nanoparticles into new ‘two-in-one’ entities. The obtained Fe₃O₄@LaF₃:Ce,Tb nanocomposites were small (about 30 nm in diameter) and well dispersed in water. Under ultraviolet light irradiation, the Fe₃O₄@LaF₃:Ce,Tb nanocomposites emitted bright green fluorescence, and they could be easily manipulated by an external magnetic field. Such bifunctional nanocomposites may find many biomedical applications, such as cancer detection and drug delivery. And the method we used can be extended to the synthesis of other nanocomposites based on lanthanide-doped materials and metal oxides.     

Magnetic field synthesis of Fe3O4 nanoparticles used as a precursor of ferrofluids

Methods to synthesize magnetic Fe₃O₄ nanoparticles and to modify the nanoparticle surface are presented in this paper. In these methods, Fe₃O₄ nanoparticles were prepared by co-precipitation, and the aging of nanoparticles was improved by applied magnetic field. The obtained nanoparticles were characterized by Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and vibrating sample magnetometer (VSM). Thereafter, to enhance the compatibility between nanoparticles and water, an effective surface modification method was developed by grafting acrylic acid onto the nanoparticle surface. FT-IR, XRD, transmission electron microscopy (TEM), and thermogravimetry (TG) were used to characterize the resultant sample. The testing results indicated that the polyacrylic acid chains have been covalently bonded to the surface of magnetic Fe₃O₄ nanoparticles. The effects of initiator dosage, monomer concentration, and reaction temperature on the characteristics of surface-modified Fe₃O₄ nanoparticles were investigated. Moreover, the Fe₃O₄-g-PAA hybrid nanoparticles were dispersed in water to form ferrofluids (FFs). The obtained FFs were characterized by UV–vis spectrophotometer, Gouy magnetic balance and laser particle-size analyzer. The testing results showed that the high-concentration FF had excellent stability, with high susceptibility and high saturation magnetization. The rheological properties of the FFs were also investigated using a rotating rheometer.     

A Study on the Rheological and Magnetic Properties of Polymer-Bonded Magnets Using Polycarbonate as the Bonding Material

The effect of three metal oxides on the magnetic properties of polymer bonded magnets (PBMs) was studied. The three PBMs, using polycarbonate (PC) as binder and 5 wt% of Fe₃O₄, Fe₂O₃, or CuO nanoparticles, were prepared by melt extrusion in a twin screw extruder followed by compression molding. Transmission electron microscopic (TEM) images showed a better dispersion for the PC/Fe₃O₄ nanocomposite compared with that of the other nanocomposites. The dynamic intersection frequency (ω_c), which is related to the crossing of the G′ and G^″ curves, showed that there was more homogeneity in the PC/Fe₃O₄ and PC/Fe₂O₃ nanocomposites. The curves of saturation magnetization for the three nanocomposites showed that there was a relationship between the magnetic properties and the homogeneity of the nanoparticles studied by rheometry. Because the magnetic strength of PC/Fe₃O₄ was greater than that of the other nanocomposites, it was concluded that not only the intrinsic magnetic property of the filler was an important factor to increase the magnetic property, but also the homogeneity of the filler within the matrix had an important role.     

Growth mechanism of ZnO nanorod/Fe3O4 nanoparticle composites and their photocatalytic properties

ZnO nanorods/Fe₃O₄ nanocomposites as the recyclable photocatalyst were synthesized by a co-precipitation method, with microwave assistant by dropping alkaline solution with Fe₃O₄ nanoparticles into the aqueous of zinc salt. These Fe₃O₄ nanoparticles were the nucleated centers for the ZnO nanorods growth so that these nanorods ended with aggregated Fe₃O₄ nanoparticles. The growth processes and mechanism are explained as those insoluble zinc hydroxides prefer to nucleate on the surface of Fe₃O₄ nanoparticles (heterogeneous nucleation) rather than nucleated as isolated ZnO nanostructures (homogeneous nucleation). These nanocomposites have strong photocatalytic ability to reduce RhB and moderate magnetization, which make them being good recyclable photocatalysts.     

Re-examination of characteristic FTIR spectrum of secondary layer in bilayer oleic acid-coated Fe3O4 nanoparticles

Bilayer oleic acid-coated Fe₃O₄ nanoparticles can be applied in more areas than single layer oleic acid-coated ones because they can be well dispersed not only in nonpolar carrier liquids but also in polar carrier liquids, while the single layer oleic acid-coated ones can be dispersed only in nonpolar carrier liquids. Therefore, it is of significance to characterize the surface structure of bilayer and single layer oleic acid-coated Fe₃O₄ nanoparticles. However, there existed a discrepancy in the characteristic FTIR spectrum of the secondary layer in bilayer oleic acid-coated Fe₃O₄ nanoparticles. The goal of this paper was to resolve the discrepancy through using FTIR and TGA together with dispersibility to characterize the surface structure of bilayer and single layer oleic acid-coated Fe₃O₄ nanoparticles. The results showed that the band at 1710 cm⁻¹ was the characteristic band of the secondary layer in bilayer oleic acid-coated Fe₃O₄ nanoparticles. It can be used to distinguish whether the oleic acid-coated Fe₃O₄ nanoparticles are bilayer or not.     

Synthesis and characterization of Fe3O4@C@Ag nanocomposites and their antibacterial performance

We synthesized Fe₃O₄@C@Ag nanocomposites through a combination of solvothermal, hydrothermal, and chemical redox reactions. Characterization of the resulting samples by X-ray diffraction, Fourier-transform infrared spectroscopy, field-emission scanning and transmission electron microscopy, and magnetic measurement is reported. Compared to Fe₃O₄@Ag nanocomposites, the Fe₃O₄@C@Ag nanocomposites showed enhanced antibacterial activity. The Fe₃O₄@C@Ag nanocomposites were able to almost entirely prevent growth of Escherichia coli when the concentration of Ag nanoparticles was 10 μg/mL. Antibacterial activity of the Fe₃O₄@C@Ag nanocomposites was maintained for more than 40 h at 37 °C. The intermediate carbon layer not only protects magnetic core, but also improves the dispersion and antibacterial activity of the silver nanoparticles. The magnetic core can be used to control the specific location of the antibacterial agent (via external magnetic field) and to recycle the residual silver nanoparticles. The Fe₃O₄@C@Ag nanocomposites will have potential uses in many fields as catalysts, absorbents, and bifunctional magnetic-optical materials.     

Superparamagnetic silica nanoparticles with immobilized metal affinity ligands for protein adsorption

Superparamagnetic silica-coated magnetite (Fe₃O₄) nanoparticles with immobilized metal affinity ligands were prepared for protein adsorption. First, magnetite nanoparticles were synthesized by co-precipitating Fe²⁺ and Fe³⁺ in an ammonia solution. Then silica was coated on the Fe₃O₄ nanoparticles using a sol–gel method to obtain magnetic silica nanoparticles. The condensation product of 3-Glycidoxypropyltrimethoxysilane (GLYMO) and iminodiacetic acid (IDA) was immobilized on them and after charged with Cu²⁺, the magnetic silica nanoparticles with immobilized Cu²⁺ were applied for the adsorption of bovine serum albumin (BSA). Scanning electron micrograph showed that the magnetic silica nanoparticles with an average size of 190 nm were well dispersed without aggregation. X-ray diffraction showed the spinel structure for the magnetite particles coated with silica. Magnetic measurement revealed the magnetic silica nanoparticles were superparamagnetic and the saturation magnetization was about 15.0 emu/g. Protein adsorption results showed that the nanoparticles had high adsorption capacity for BSA (73 mg/g) and low nonspecific adsorption. The regeneration of these nanoparticles was also studied.     

Facile synthesis of multifunctional Ag/Fe3O4-CS nanocomposites for antibacterial and hyperthermic applications

Nanocomposites containing two or more functional constituents are attractive candidates for advanced nanomaterials. In this study, multifunctional Ag/Fe₃O₄-CS nanocomposites were successfully prepared, using chitosan as a stabilizing and cross-linking agent. The as-synthesized nanocomposites were characterized by Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), X-ray diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDS), UV–visible spectrophotometer (UV–Vis) and vibrating sample magnetometer (VSM). The results demonstrated that Ag/Fe₃O₄-CS composite nanoparticles (NPs) were composed of parent components, Fe₃O₄ and Ag NPs, which were uniformly dispersed in the chitosan matrix. The hybrid NPs exhibited strong antibacterial property against Pseudomonas aeruginosa. With high magnetization value (67 emu/g), the synthesized Ag/Fe₃O₄-CS composite can be easily separated or recycled in potential biomedical applications. Furthermore, the results showed that the multicomponent hybrid nanostructures appeared to be the promising material for local hyperthermia, which can be used as thermoseeds for localized hyperthermia treatment of cancers.     

PVDF/PS/HDPE/MWCNTs/Fe3O4 nanocomposites: Effective and lightweight electromagnetic interference shielding material through the synergetic effect of MWCNTs and Fe3O4 nanoparticles

In this work, Polyvinylidene Fluoride (PVDF)/polystyrene (PS)/high density polyethylene (HDPE) ternary blends displayed a core-shell structure where HDPE was the core, PS was the shell, and this core-shell system dispersed in PVDF matrix. Here, multiwall carbon nanotubes (MWCNTs) and ferroferric oxide (Fe₃O₄) was incorporated. F-F composites with MWCNTs was in PS shell and Fe₃O₄ was in PVDF matrix and E-F composites with MWCNTs was in PS shell and Fe₃O₄ was in HDPE core were fabricated by melt blending. It was indicated that the core-shell morphology between PS and HDPE was well retained with the incorporation of Fe₃O₄ and MWCNTs. Both the electrical conductivity of F-F and E-F composites were similar without no obvious change with the incorporation of Fe₃O₄. Composites with greater than 20 dB shielding effectiveness were easy to obtain. The highest SE we observed was for the F-F composite with 1 vol% Fe₃O₄ and 1 vol% MWCNTs was 25 dB at 9.5 GHz, and the SE was over 20 dB in the whole measured frequency(X-band). The E-F composites with SE greater than 20 dB in X-band was at 2 vol% Fe₃O₄ and 1 vol% MWNCTs. Such effective and lightweight nanocomposites were obtained, resulting from the synergetic effect of MWCNTs and Fe₃O₄ nanoparticles.     

Synthesis and characterization of noscapine loaded magnetic polymeric nanoparticles

The delivery of noscapine therapies directly to the site of the tumor would ultimately allow higher concentrations of the drug to be delivered, and prolong circulation time in vivo to enhance the therapeutic outcome of this drug. Therefore, we sought to design magnetic based polymeric nanoparticles for the site directed delivery of noscapine to invasive tumors. We synthesized Fe₃O₄ nanoparticles with an average size of 10±2.5 nm. These Fe₃O₄ NPs were used to prepare noscapine loaded magnetic polymeric nanoparticles (NMNP) with an average size of 252±6.3 nm. Fourier transform infrared (FT-IR) spectroscopy showed the encapsulation of noscapine on the surface of the polymer matrix. The encapsulation of the Fe₃O₄ NPs on the surface of the polymer was confirmed by elemental analysis. We studied the drug loading efficiency of polylactide acid (PLLA) and poly (l-lactide acid-co-gylocolide) (PLGA) polymeric systems of various molecular weights. Our findings revealed that the molecular weight of the polymer plays a crucial role in the capacity of the drug loading on the polymer surface. Using a constant amount of polymer and Fe₃O₄ NPs, both PLLA and PLGA at lower molecule weights showed higher loading efficiencies for the drug on their surfaces.     

Effect of ferrofluid concentration on electrical and magnetic properties of the Fe3O4/PANI nanocomposites

Magnetic nanocomposites can be controlled and tailored to provide the desired mechanical, physical, chemical, and biomedical properties depending on the final applications. The coating of ferrite nanoparticles with polymers affords the possibility of minimizing agglomeration in large-scale commercial synthesis of nanocomposite materials. The process of coating not only provides effective encapsulation of individual nanoparticles, but also controls the growth in size, thus, yielding a better overall size distribution. In this paper, in-situ polymerization of aniline was carried out in different concentration of the ferrofluid with the aim to obtain agglomerate free nanocomposites. The role of the ferrite concentration was investigated by the spectral, morphological, conductivity, and magnetic properties of Fe₃O₄/polyaniline (PANI) nanocomposites. XRD revealed the presence of spinel phase of Fe₃O₄ and the particle size was calculated to be 14.3 nm. Spectral analysis confirmed the formation of PANI encapsulated Fe₃O₄ nanocomposite. Conductivity of the nanocomposites was found to be in the range of 0.001–0.003 S/cm. Higher saturation magnetization of 3.2 emu/g was observed at 300 K, revealing a super paramagnetic behavior of this nanocomposite.