Magnetically assisted solid phase extraction using Fe3O4 nanoparticles combined with enhanced spectrofluorimetric detection for aflatoxin M1 determination in milk samples

A novel, facile and inexpensive solid phase extraction (SPE) method using ethylene glycol bis-mercaptoacetate modified 3-(trimethoxysilyl)-1-propanethiol grafted Fe₃O₄ nanoparticles coupled with spectrofluorimetric detection was proposed for determination of aflatoxin M1 (AFM1) in liquid milk samples. The method uses the advantage fluorescence enhancement by β-cyclodexterin complexation of AFM1 in 12% (v/v) acetonitrile–water and the remarkable properties of Fe₃O₄ nanoparticles namely high surface area and strong magnetization were utilized to achieve high enrichment factor (57) and satisfactory extraction recoveries (91–102%) using only 100 mg of magnetic adsorbent. Furthermore, fast separation time of about 15 min avoids many time-consuming column-passing procedures of conventional SPE. The main factors affecting extraction efficiency including pH value, desorption conditions, extraction/desorption time, sample volume, and adsorbent amount were evaluated and optimized. Under the optimal conditions, a wide linear range of 0.04–8 ng mL⁻¹ with a low detection limit of 0.015 ng mL⁻¹ was obtained. The developed method was applied for extraction and preconcentration of AFM1 in three commercially available milk samples and the results were compared with the official AOAC method.     

Preparation of Fe3O4 nanoparticle enclosure hydroxylated multi-walled carbon nanotubes for the determination of aconitines in human serum samples

A magnetic carbon nanomaterial for Fe₃O₄ enclosure hydroxylated multi-walled carbon nanotubes (Fe₃O₄-EC-MWCNTs-OH) was prepared by the aggregating effect of Fe₃O₄ nanoparticle on MWCNTs-OH, and combined with high-performance liquid chromatography (HPLC)/diode array detection (DAD) to determine the aconitines (aconitine, hypaconitine and mesaconitine) in human serum samples. Compared with other extraction modes investigated in experiment, Fe₃O₄-EC-MWCNTs-OH sorbents showed a good affinity to target analytes. Some important parameters that could influence extraction efficiency of aconitines, including the extraction mode, amounts of Fe₃O₄-EC-MWCNTs-OH, pH of sample solution, extraction time, desorption solvent and desorption time, were optimized. Under optimal conditions, the recoveries of spiked serum samples were between 98.0% and 103.0%; relative standard deviations (RSDs) ranged from 0.9% to 6.2%. The correlation coefficients varied from 0.9996 to 0.9998. The limits of detection ranged from 3.1 ng mL⁻¹ to 4.1 ng mL⁻¹ at a signal-to-noise ratio of 3. The experimental results showed that the proposed method was feasible for the analysis of aconitines in serum samples.     

Enzyme mimics of spinel-type CoxNi1−xFe2O4 magnetic nanomaterial for eletroctrocatalytic oxidation of hydrogen peroxide

A series of spinel-type Co_xNi_1−xFe₂O₄ (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) magnetic nanomaterials were solvothermally synthesized as enzyme mimics for the eletroctrocatalytic oxidation of H₂O₂. X-ray diffraction and scanning electron microscope were employed to characterize the composition, structure and morphology of the material. The electrochemical properties of spinel-type Co_xNi_1−xFe₂O₄ with different (Co/Ni) molar ratio toward H₂O₂ oxidation were investigated, and the results demonstrated that Co_0.5Ni_0.5Fe₂O₄ modified carbon paste electrode (Co_0.5Ni_0.5Fe₂O₄/CPE) possessed the best electrocatalytic activity for H₂O₂ oxidation. Under optimum conditions, the calibration curve for H₂O₂ determination on Co_0.5Ni_0.5Fe₂O₄/CPE was linear in a wide range of 1.0 × 10⁻⁸–1.0 × 10⁻³ M with low detection limit of 3.0 × 10⁻⁹ M (S/N = 3). The proposed Co_0.5Ni_0.5Fe₂O₄/CPE was also applied to the determination of H₂O₂ in commercial toothpastes with satisfactory results, indicating that Co_xNi_1−xFe₂O₄ is a promising hydrogen peroxidase mimics for the detection of H₂O₂.     

Quenched electrochemiluminescence of Ag nanoparticles functionalized g-C3N4 by ferrocene for highly sensitive immunosensing

In this paper, a novel sandwich electrochemiluminescence (ECL) immunosensor was constructed by ferrocene for quenching Ag nanoparticles functionalized g-C₃N₄ (Ag@g-C₃N₄) emission. The prepared Ag@g-C₃N₄ had strong and stable ECL signals compared to pure g-C₃N₄ and primary antibody (Ab₁) can be immobilized on Ag@g-C₃N₄ by adsorption of Ag nanoparticles. Ferrocene carboxylic acid (Fc-COOH) labeled secondary antibody was immobilized on Au doped mesoporous Al₂O₃ nanorods (Au@Al₂O₃–Fc-COOH@Ab₂) as labels through adsorption ability of Au toward proteins. After a sandwich-type immunoreaction, a remarkable decrease of ECL signal was observed due to the ECL quenching of Ag@g-C₃N₄ by Au@Al₂O₃–Fc-COOH@Ab₂. As a result, the change of ECL intensity has a direct relationship with the logarithm of CEA concentrations in the range of 1 pg mL⁻¹–100 ng mL⁻¹ with a detection limit of 0.35 pg mL⁻¹ (S/N = 3). Additionally, the proposed immunosensor shows high specificity, good reproducibility, and long-term stability.     

Sol-gel synthesized semiconducting LaCo0.8Fe0.2O3-based powder for thick film NH3 gas sensor

Perovskite type LaCo_xFe_1−xO₃ nanoparticles was synthesized by a sol-gel citrate method. The structural, electrical and sensing characteristics of the LaCo_xFe_1−xO₃ system were investigated. The structural characteristics were performed by using X-ray diffraction (XRD) and transmission electron microscopy (TEM) to examine the phase and morphology of the resultant powder. The XRD pattern shows nanocrystalline solid solution of LaCo_xFe_1−xO₃ with perovskite phase. Electrical properties of synthesized nanoparticles are studied by DC conductivity measurement. The sensor shows high response towards ammonia gas in spite of other reducing gases when x = 0.8. The effect of 0.3 wt.% Pd-doped LaCo_0.8Fe_0.2O₃ on the response and a recovery time was also addressed.     

Synthesis, structure and magnetic properties of porous magnetic composite, based on MCM-41 molecular sieve with Fe3O4 nanoparticles

Porous magnetic composites were prepared by the synthesis of molecular sieve MCM-41 in the presence of Fe₃O₄ nanoparticles with average diameter of 15 nm. Nanoparticles were captured by porous silica matrix MCM-41, which resulted in their incorporation, as it was confirmed by TEM, SEM and X-ray diffraction. The materials possessed high surface area (392-666 m² g⁻¹), high pore volume (0.39-0.73 cm³ g⁻¹) along with high magnetic response (M_S up to 28.4 emu g⁻¹ at 300 K). Calcination of samples resulted in partial oxidation of Fe₃O₄ to α-Fe₂O₃. The influence of nanoparticles content on sorption and magnetic properties of the composites was shown. No hysteresis was found for the samples at 300 K; at 5 K, H_C was in the range 370-385 G for non-calcinated samples and 350-356 G for calcinated ones.     

Effect of capping and particle size on Raman laser-induced degradation of γ-Fe2O3 nanoparticles

Diol capped γ-Fe₂O₃ nanoparticles are prepared from ferric nitrate by refluxing in 1,4-butanediol (9.5 nm) and 1,5-pentanediol (15 nm) and uncapped particles are prepared by refluxing in 1,2-propanediol followed by sintering the alkoxide formed. X-ray diffraction (XRD) shows that all the samples have the spinel phase. Raman spectroscopy shows that the samples prepared in 1,4-butanediol and 1,5-pentanediol and 1,2-propanediol (sintered at 573 and 673 K) are γ-Fe₂O₃ and the 773 K-sintered sample is Fe₃O₄. Raman laser studies carried out at various laser powers show that all the samples undergo laser-induced degradation to α-Fe₂O₃ at higher laser power. The capped samples are however, found more stable to degradation than the uncapped samples. The stability of γ-Fe₂O₃ sample with large particle size (15.4 nm) is more than the sample with small particle size (10.2 nm). Fe₃O₄ having a particle size of 48 nm is however less stable than the smaller γ-Fe₂O₃ nanoparticles.     

Preparation of carbon coated Fe3O4 nanoparticles and their application for solid-phase extraction of polycyclic aromatic hydrocarbons from environmental water samples

The carbon coated Fe₃O₄ nanoparticles (Fe₃O₄/C) were synthesized by a simple hydrothermal reaction and applied as solid-phase extraction (SPE) sorbents to extract trace polycyclic aromatic hydrocarbons (PAHs) from environmental water samples. The Fe₃O₄/C sorbents possess high adsorption capacity and extraction efficiency due to strong adsorption ability of carbon materials and large surface area of nanoparticles, and only 50 mg of sorbents are required to extract PAHs from 1000 mL water samples. The adsorption attains equilibrium rapidly and analytes are eluted with acetonitrile readily. Salinity and solution pH have no obvious effect on the recoveries of PAHs, which avoids fussy adjustment to water sample before extraction. Under optimized conditions, the detection limits of PAHs are in the range of 0.2–0.6 ng L⁻¹. The accuracy of the method was evaluated by the recoveries of spiked samples. Good recoveries (76–110%) with low relative standard deviations from 0.8% to 9.7% are achieved. This new SPE method provides several advantages, such as high extraction efficiency, high breakthrough volumes, convenient extraction procedure, and short analysis times. To our knowledge, this is the first time that Fe₃O₄/C nanoparticles are used for the pretreatment of environmental water samples.     

In-tube magnetic solid phase microextraction of some fluoroquinolones based on the use of sodium dodecyl sulfate coated Fe3O4 nanoparticles packed tube

In-tube magnetic solid phase microextraction (in-tube MSPME) of fluoroquinolones from water and urine samples based on the use of sodium dodecyl sulfate (SDS) coated Fe₃O₄ nanoparticles packed tube has been reported. After the preparation of Fe₃O₄ nanoparticles (NPs) by a batch synthesis, these NPs were introduced into a stainless steel tube by a syringe and then a strong magnet was placed around the tube, so that the Fe₃O₄ NPs were remained in the tube and the tube was used in the in-tube SPME-HPLC/UV for the analysis of fluoroquinolones in water and urine samples. Plackett–Burman design was employed for screening the variables significantly affecting the extraction efficiency. Then, the significant factors were more investigated by Box–Behnken design. Calibration curves were linear (R² > 0.990) in the range of 0.1–1000 μg L⁻¹ for ciprofloxacin (CIP) and 0.5–500 μg L⁻¹ for enrofloxacin (ENR) and ofloxacin (OFL), respectively. LODs for all studied fluoroquinolones ranged from 0.01 to 0.05 μg L⁻¹. The main advantages of this method were rapid and easy automation and analysis, short extraction time, high sensitivity, possibility of fully sorbent collection after analysis, wide linear range and no need to organic solvents in extraction.     

Humidity effects in Fe16N2 fine powder preparation by low-temperature nitridation

Low-temperature nitridation has been reported to produce ferromagnetic α″-Fe₁₆N₂ by ammonia nitridation of α-Fe fine powder, which was obtained from the reduction of vapor-grown γ-Fe₂O₃. The effects of humidity during this preparation were investigated in the present study. α″-Fe₁₆N₂ was inconsistently obtained, and at low yield, from Fe₃O₄ fine powder (MT-40) prepared from aqueous solution. Reducing the adsorbed water content in the iron oxide starting powder resulted in improved reproducibility of the α″-Fe₁₆N₂ yield of the nitridation. The use of a smaller-diameter reaction tube, less than 25 mm in diameter, enabled more reproducible preparation from vapor-grown γ-Fe₂O₃ powder (CI-30). The reaction yield was further improved by using high-quality ammonia with a water content of ≤0.05 ppm. Minimizing the humidity made it possible to obtain a fine powder with a high α″-Fe₁₆N₂ content. Enhancement of the magnetization to 210 emu g⁻¹ at room temperature was observed from a nitrided mixture of α″-Fe₁₆N₂ with residual α-Fe, compared to 199 emu g⁻¹ for an α-Fe fine powder reduced from γ-Fe₂O₃. However, excess nitrogen and residual oxygen in the nitrided products reduced the magnetization below the value of α-Fe powder after nitridation. The magnetization was enhanced in nitrided products with a nitrogen content slightly below the stoichiometric amount for α″-Fe₁₆N₂.     

High-pressure transitions in MgAl2O4 and a new high-pressure phase of Mg2Al2O5

Phase transitions in MgAl₂O₄ were examined at 21-27 GPa and 1400-2500 °C using a multianvil apparatus. A mixture of MgO and Al₂O₃ corundum that are high-pressure dissociation products of MgAl₂O₄ spinel combines into calcium-ferrite type MgAl₂O₄ at 26-27 GPa and 1400-2000 °C. At temperature above 2000 °C at pressure below 25.5 GPa, a mixture of Al₂O₃ corundum and a new phase with Mg₂Al₂O₅ composition is stable. The transition boundary between the two fields has a strongly negative pressure-temperature slope. Structure analysis and Rietveld refinement on the basis of the powder X-ray diffraction profile of the Mg₂Al₂O₅ phase indicated that the phase represented a new structure type with orthorhombic symmetry (Pbam), and the lattice parameters were determined as a=9.3710(6) Å, b=12.1952(6) Å, c=2.7916(2) Å, V=319.03(3) Å³, Z=4. The structure consists of edge-sharing and corner-sharing (Mg, Al)O₆ octahedra, and contains chains of edge-sharing octahedra running along the c-axis. A part of Mg atoms are accommodated in six-coordinated trigonal prism sites in tunnels surrounded by the chains of edge-sharing (Mg, Al)O₆ octahedra. The structure is related with that of ludwigite (Mg, Fe²⁺)₂(Fe³⁺, Al)(BO₃)O₂. The molar volume of the Mg₂Al₂O₅ phase is smaller by 0.18% than sum of molar volumes of 2MgO and Al₂O₃ corundum. High-pressure dissociation to the mixture of corundum-type phase and the phase with ludwigite-related structure has been found only in MgAl₂O₄ among various A²⁺B³⁺₂O₄ compounds.     

Magnetic Fe3O4@Au composite-enhanced surface plasmon resonance for ultrasensitive detection of magnetic nanoparticle-enriched α-fetoprotein

Small molecules or analytes present at low concentrations are difficult to detect directly using conventional surface plasmon resonance (SPR) techniques because only small changes in the refractive index of the medium are typically induced by the binding of these analytes. Here, we present an amplification technique using core–shell Fe₃O₄@Au magnetic nanoparticles (MNPs) for an SPR bioassay. To evaluate this amplification effect, a novel SPR sensor based on a sandwich immunoassay was developed to detect α-fetoprotein (AFP) by immobilizing a primary AFP antibody (Ab₁) on the surface of a 3-mercapto-1-propanesulfonate/chitosan-ferrocene/Au NP (MPS/CS-Fc/Au NP) film employing Fe₃O₄@Au–AFP secondary antibody conjugates (Fe₃O₄@Au–Ab₂) as the amplification reagent. The stepwise fabrication of the biosensor was characterized using UV-vis spectroscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. A calibration curve of Fe₃O₄@Au–Ab₂ conjugates amplification for AFP detection was obtained to yield a correlation in the range of 1.0–200.0 ng mL⁻¹ with a detection limit of 0.65 ng mL⁻¹, and a significant increase in sensitivity was therefore afforded through the use of Fe₃O₄@Au–Ab₂ conjugates as an amplifier. This magnetic separation and amplification strategy has great potential for the detection of other biomolecules of interest with low interference and high sensitivity by changing the antibody label used in the Fe₃O₄@Au–antibody conjugates.     

A novel nonenzymatic sensor based on LaNi0.6Co0.4O3 modified electrode for hydrogen peroxide and glucose

In this paper, LaNi_0.6Co_0.4O₃ (LNC) nanoparticles were synthesized by the sol–gel method, and the structure and morphology of LNC nanoparticles were characterized by X-ray diffraction spectrum, scanning electron microscopy and transmitting electron microscopy. And then, LNC was used to modify carbon paste electrode (CPE) without any adhesive to fabricate hydrogen peroxide and glucose sensor, and the results demonstrated that LNC exhibited strong electrocatalytical activity by cyclic voltammetry and amperometry. In H₂O₂ determination, linear response was obtained in the concentration range of 10 nM–100 μM with a detection limit of 1.0 nM. In glucose determination, there was the linear region of 0.05–200 μM with a detection limit of 8.0 nM. Compared with other reports, the proposed sensor also displayed high sensitivity toward H₂O₂ (1812.84 μA mM⁻¹ cm⁻²) and glucose (643.0 μA mM⁻¹ cm⁻²). Moreover, this prepared sensor was applied to detect glucose in blood serum and hydrogen peroxide in toothpaste samples with satisfied results, indicating its possibility in practical application.     

Synthesis of Fe3O4\SiO2\Ag nanoparticles and its application in surface-enhanced Raman scattering

To obtain a recyclable surface-enhanced Raman scattering (SERS) material, we developed a composite of Fe₃O₄\SiO₂\Ag with core\shell\particles structure. The designed particles were synthesized via an ultrasonic route. The Raman scattering signal of Fe₃O₄ could be shielded by increasing the thickness of the SiO₂ layer to 60 nm. Dye rhodamine B (RB) was chosen as probe molecule to test the SERS effect of the synthesized Fe₃O₄\SiO₂\Ag particles. On the synthesized Fe₃O₄\SiO₂\Ag particles, the characteristic Raman bands of RB could be observed when the RB solution was diluted to 5 ppm (1×10⁻⁵ M). Furthermore, the synthesized particles could keep their efficiency till four cycles.     

Polythiophene-coated Fe3O4 superparamagnetic nanocomposite: Synthesis and application as a new sorbent for solid-phase extraction

In the present work, a novel type of superparamagnetic nanosorbent, polythiophene-coated Fe₃O₄ nanoparticles (Fe₃O₄@PTh NPs), have been successfully synthesized. The synthesized NPs were characterized by scanning electron microscopy (SEM), Fourier transform-infrared (FT-IR) spectroscopy, and thermal gravimetric analysis (TGA). The synthesized Fe₃O₄@PTh NPs were applied as an efficient sorbent for extraction and preconcentration of several typical plasticizer compounds (di-n-butyl phthalate (DBP), di-(2-ethylhexyl) phthalate (DEHP), and dioctyl adipate (DOA)) from environmental water samples. Separation of Fe₃O₄@PTh NPs from the aqueous solution was simply achieved by applying external magnetic field. Separation and determination of the extracted plasticizers was performed by gas chromatography–flame ionization detection (GC–FID). Several variables affecting the extraction efficiency of the analytes i.e., amount of NPs sorbent, salt concentration, extraction time, and desorption conditions were investigated and optimized. The best working conditions were as follows: amount of sorbent, 100 mg; NaCl concentration, 30% (w/v); sample volume, 45 mL; extraction time, 10 min; and 100 μL of ethyl acetate for desorption of the analytes within 2 min. Under optimized conditions, preconcentration factors for DBP, DEHP, and DOA were obtained as 86, 194, and 213, respectively. The calibration curves were linear (R² > 0.998) in the concentration range of 0.4–100 μg L⁻¹ for both DEHP and DOA and 0.7–100 μg L⁻¹ for DBP. The limits of detection (LODs) were obtained in the range of 0.2–0.4 μg L⁻¹. The intra-day relative standard deviations (RSDs%) based on four replicates were obtained in the range of 4.0–12.3%. The proposed procedure was applied to analysis of water samples including river water, bottled mineral water, and boiling water exposed to polyethylene container (after cooling) and recoveries between 85 and 99% and RSDs lower than 12.8% were obtained.     

Phase formation, crystal chemistry, and properties in the system Bi2O3-Fe2O3-Nb2O5

Subsolidus phase relations have been determined for the Bi₂O₃-Fe₂O₃-Nb₂O₅ system in air (900-1075 °C). Three new ternary phases were observed—Bi₃Fe_0.5Nb_1.5O₉ with an Aurivillius-type structure, and two phases with approximate stoichiometries Bi₁₇Fe₂Nb₃₁O₁₀₆ and Bi₁₇Fe₃Nb₃₀O₁₀₅ that appear to be structurally related to Bi₈Nb₁₈O₅₇. The fourth ternary phase found in this system is pyrochlore (A₂B₂O₆O′), which forms an extensive solid solution region at Bi-deficient stoichiometries (relative to Bi₂FeNbO₇) suggesting that ≈4-15% of the A-sites are occupied by Fe³⁺. X-ray powder diffraction data confirmed that all Bi-Fe-Nb-O pyrochlores form with positional displacements, as found for analogous pyrochlores with Zn, Mn, or Co instead of Fe. A structural refinement of the pyrochlore 0.4400:0.2700:0.2900 Bi₂O₃:Fe₂O₃:Nb₂O₅ using neutron powder diffraction data is reported with the A cations displaced (0.43 Å) to 96g sites and O′ displaced (0.29 Å) to 32e sites (Bi_1.721Fe_0.190(Fe_0.866Nb_1.134)O₇, Fd3¯m (#227), ). This displacive model is somewhat different from that reported for Bi_1.5Zn_0.92Nb_1.5O_6.92, which exhibits twice the concentration of small B-type cations on the A-sites as the Fe system. Bi-Fe-Nb-O pyrochlores exhibited overall paramagnetic behavior with large negative Curie-Weiss temperature intercepts, slight superparamagnetic effects, and depressed observed moments compared to high-spin, spin-only values. The single-phase pyrochlore with composition Bi_1.657Fe_1.092Nb_1.150O₇ exhibited low-temperature dielectric relaxation similar to that observed for Bi_1.5Zn_0.92Nb_1.5O_6.92; at 1 MHz and 200 K the relative permittivity was 125, and above 350 K conductive effects were observed.     

Electrocatalytic oxidation behavior of guanosine at graphene, chitosan and Fe3O4 nanoparticles modified glassy carbon electrode and its determination

A graphene, chitosan and Fe₃O₄ nanoparticles (nano-Fe₃O₄) modified glassy carbon electrode (graphene-chitosan/nano-Fe₃O₄/GCE) was fabricated. The modified electrode was characterized by scanning electron microscope and electrochemical impedance spectroscopy. The electrochemical oxidation behavior of guanosine was investigated in pH 7.0 phosphate buffer solution by cyclic voltammetry and differential pulse voltammetry. The experimental results indicated that the modified electrode exhibited an electrocatalytic and adsorptive activities towards the oxidation of guanosine. The transfer electron number (n), transfer proton number (m) and electrochemically effective surface area (A) were calculated. Under the optimized conditions, the oxidation peak current was proportional to guanosine concentration in the range of 2.0 × 10⁻⁶ to 3.5 × 10⁻⁴ mol L⁻¹ with the correlation coefficient of 0.9939 and the detection limit of 7.5 × 10⁻⁷ mol L⁻¹ (S/N = 3). Moreover, the modified electrode showed good ability to discriminate the electrochemical oxidation response of guanosine, guanine and adenosine. The proposed method was further applied to determine guanosine in spiked urine samples and traditional Chinese medicines with satisfactory results.     

纳米Fe_3O_4及钴离子掺杂Fe_3O_4:有机碱共沉淀制备和磁性质

以有机碱四甲基氢氧化铵(TMAH)为沉淀剂合成了纳米Fe3O4和Co2+掺杂的纳米Fe3O4粒子。分别讨论了碱用量,铁盐溶液浓度,反应温度,有机碱及PEG-4000的分散性等因素对纳米Fe3O4的形貌影响。结果表明,所合成的纳米Fe3O4为30nm左右的反尖晶石型面心立方结构,有机碱除了起沉淀剂作用,还能够提高纳米Fe3O4的分散性。本文还讨论了不同Co2+掺入量的纳米Fe3O4粒子的磁性质,结果表明Co2+掺杂的纳米Fe3O4粒子的矫顽力在不同掺入量的下有较大的改变。当Co2+掺入量为10.0%时,纳米Fe3O4的矫顽力达到最大值,为1628Oe。     

Improve the catalytic activity of α-Fe2O3 particles in decomposition of ammonium perchlorate by coating amorphous carbon on their surface

Sphere- and pod-like α-Fe₂O₃ particles have been selectively synthesized using NH₃·H₂O and NaOH solution to adjust the pH value of the designed synthetic system, respectively. The sphere-like α-Fe₂O₃ particles with diameter about 25 nm on average were encapsulated into carbon shells to fabricate a novel core-shell composite (α-Fe₂O₃@C) through the coating experiments. The catalytic performance of the products on the thermal decomposition of ammonium perchlorate (AP) was investigated by thermal gravimetric analyzer (TG) and differential thermal analysis (DTA). The thermal decomposition temperatures of AP in the presence of pod-like α-Fe₂O₃, sphere-like α-Fe₂O₃ and α-Fe₂O₃@C are reduced by 72, 81 and 109 °C, respectively, which show that α-Fe₂O₃@C core-shell composites have higher catalytic activity than that of α-Fe₂O₃.     

CoFe2O4 nano-particles functionalized with 8-hydroxyquinoline for dispersive solid-phase micro-extraction and direct fluorometric monitoring of aluminum in human serum and water samples

A simple dispersive solid-phase micro-extraction method based on CoFe₂O₄ nano-particles (NPs) functionalized with 8-hydroxyquinoline (8-HQ) with the aid of sodium dodecyl sulfate (SDS) was developed for separation of Al(III) ions from aqueous solutions. Al(III) ions are separated at pH 7 via complex formation with 8-HQ using the functionalized CoFe₂O₄ nano-particles sol solution as a dispersed solid-phase extractor. The separated analyte is directly quantified by a spectrofluorometric method at 370 nm excitation and 506 nm emission wavelengths. A comparison of the fluorescence of Al(III)–8-HQ complex in bulk solution and that of Al(III) ion interacted with 8-HQ/SDS/CoFe₂O₄ NPs revealed a nearly 5-fold improvement in intensity. The experimental factors influencing the separation and in situ monitoring of the analyte were optimized. Under these conditions, the calibration graph was linear in the range of 0.1–300 ng mL⁻¹ with a correlation coefficient of 0.9986. The limit of detection and limit of quantification were 0.03 ng mL⁻¹ and 0.10 ng mL⁻¹, respectively. The inter-day and intra-day relative standard deviations for six replicate determinations of 150 ng mL⁻¹ Al(III) ion were 2.8% and 1.7%, respectively. The method was successfully applied to direct determine Al(III) ion in various human serum and water samples.