On-chip graphene oxide aptasensor for multiple protein detection

The versatility of an on-chip graphene oxide (GO) aptasensor was successfully confirmed by the detection of three different proteins, namely, thrombin (TB), prostate specific antigen (PSA), and hemagglutinin (HA), simply by changing the aptamers but with the sensor composition remaining the same. The results indicate that both DNA and RNA aptamers immobilized on the GO surface are sufficiently active to realize an on-chip aptasensor. Molecular selectivity and concentration dependence were investigated in relation to TB and PSA detection by using a dual, triple, and quintuple microchannel configuration. The multiple target detection of TB and PSA on a single chip was also demonstrated by using a 2 × 3 linear-array GO aptasensor. This work enables us to apply this sensor to the development of a multicomponent analysis system for a wide variety of targets by choosing appropriate aptamers.     

基于新型纳米传感材料的DNA生物传感器的应用

DNA是构建纳米技术和生物传感技术新设备的良好构建体。DNA生物传感器由于具有灵敏度高、选择性好等特点,近年来获得了飞速发展。研究发现,金属纳米粒子(MNPs)、碳基纳米材料等一系列纳米材料在传感器设计中提高了电化学DNA传感器的传感性能。本文侧重介绍了场效应晶体管、石墨烯、碳纳米管等新型纳米传感材料,以及基于这些材料的DNA生物传感器的最新进展,最后展望了DNA生物传感器的应用前景。     

Functionalisation of Graphene Sensor Surfaces for the Specific Detection of Biomarkers

We report on a controllable and specific functionalisation route for graphene field-effect transistors (GFETs) for the recognition of small physiologically active molecules. Key element is the noncovalent functionalisation of the graphene surface with perylene bisimide (PBI) molecules directly on the growth substrate. This Functional Layer Transfer enables the homogeneous self-assembly of PBI molecules on graphene, onto which antibodies are subsequently immobilised. The sensor surface was characterised by atomic force microscopy, Raman spectroscopy and electrical measurements, showing superior performance over conventional functionalisation after transfer. Specific sensing of small molecules was realised by monitoring the electrical property changes of functionalised GFET devices upon the application of methamphetamine and cortisol. The concentration dependent electrical response of our sensors was determined down to a concentration of 300 ng ml⁻¹ for methamphetamine.     

Optically Triggered Control of the Charge Carrier Density in Chemically Functionalized Graphene Field Effect Transistors

Field effect transistors (FETs) based on 2D materials are of great interest for applications in ultrathin electronic and sensing devices. Here we demonstrate the possibility to add optical switchability to graphene FETs (GFET) by functionalizing the graphene channel with optically switchable azobenzene molecules. The azobenzene molecules were incorporated to the GFET channel by building a van der Waals heterostructure with a carbon nanomembrane (CNM), which is used as a molecular interposer to attach the azobenzene molecules. Under exposure with 365 nm and 455 nm light, azobenzene molecules transition between cis and trans molecular conformations, respectively, resulting in a switching of the molecular dipole moment. Thus, the effective electric field acting on the GFET channel is tuned by optical stimulation and the carrier density is modulated.     

Molecularly engineered graphene surfaces for sensing applications: A review

Graphene is scientifically and commercially important because of its unique molecular structure which is monoatomic in thickness, rigorously two-dimensional and highly conjugated. Consequently, graphene exhibits exceptional electrical, optical, thermal and mechanical properties. Herein, we critically discuss the surface modification of graphene, the specific advantages that graphene-based materials can provide over other materials in sensor research and their related chemical and electrochemical properties. Furthermore, we describe the latest developments in the use of these materials for sensing technology, including chemical sensors and biosensors and their applications in security, environmental safety and diseases detection and diagnosis.     

Nucleic acid functionalized graphene for biosensing

There is immense demand for complex nanoarchitectures based on graphene nanostructures in the fields of biosensing or nanoelectronics. DNA molecules represent the most versatile and programmable recognition element and can provide a unique massive parallel assembly strategy with graphene nanomaterials. Here we demonstrate a facile strategy for covalent linking of single stranded DNA (ssDNA) to graphene using carbodiimide chemistry and apply it to genosensing. Since graphenes can be prepared by different methods and can contain various oxygen containing groups, we thoroughly investigated the utility of four different chemically modified graphenes for functionalization by ssDNA. The materials were characterized in detail and the different DNA functionalized graphene platforms were then employed for the detection of DNA hybridization and DNA polymorphism by using impedimetric methods. We believe that our findings are very important for the development of novel devices that can be used as alternatives to classical techniques for sensitive and fast DNA analysis. In addition, covalent functionalization of graphene with ssDNA is expected to have broad implications, from biosensing to nanoelectronics and directed, DNA programmable, self-assembly.     

On the role of substituent in noncovalent functionalization of graphene and organophosphor recognition: IQA and SAPT perspective

Despite importance of integrating organic molecules with graphene to fabricate graphene‐based electronic devices, the role of substituents and interface stabilizing forces are poorly understood. In this work, the interactions of 7,7,8,8‐tetracyanoquinodimethane (TCNQ), 2,3,5,6‐tetrafluoro‐7,7,8,8‐tetracyanoquinodimethane (F4TCNQ), hydroquinone (Q), and tetrafluorohydroquinone (TFQ) with graphene have been investigated by means of interacting quantum atoms and SAPT(DFT). In addition, in context of potential design of a graphene‐based sensor for detection of the nerve agent sarin, we studied the interaction of graphene and the organic molecules with the dimethyl methylphosphonate (DMMP)—the molecule that mimics sarin. The results show that the organic molecules attach to graphene via C(sp²)?C(sp²), C(sp²)?C(sp) and H?π bonds. In addition, they trap DMMP via various linkages such as hydrogen, lonepair?π and H?π . The quantum effects play a significant role. The Pauli repulsion is responsible for p‐doping of graphene. The substituents are stabilized on graphene by the exchange‐correlation energy. The fluorination of the benzenoid ring raises the electron‐sharing . The through space and through bond effects of the fluorine atoms (‐F) increase the classical attraction of the cyano groups and benzenoid ring with graphene, respectively. When comparing performance of the ab initio and DFT methods, MP2 predicts too much attraction due to well‐known overestimation of the dispersion energy by the uncoupled dispersion component for benzene rings, while ω B97xD functional and SAPT(DFT) provide weaker interaction energies, in good agreement with each other.     

Paper-based solid-state electrochemiluminescence sensor using poly(sodium 4-styrenesulfonate) functionalized graphene/nafion composite film

Herein, highly efficient solid-state ECL sensor was introduced for the first time onto the screen printed electrodes of the paper-based chips (PCs) based on the composite film of poly(sodium 4-styrenesulfonate) functionalized graphene (PSSG) and Nafion. Attributed to the cooperative characteristics of both PSS and graphene, PSSG ensured both effective Ru(bpy)₃²⁺ immobilization and fast electron transfer of Ru(bpy)₃²⁺ in the composite film. The ECL behaviors at the developed sensor were investigated using tripropylamine as a representative analyte and low detection limit (S N⁻¹ = 3) of 5.0 nM was obtained. It also exhibited more excellent reproducibility (relative standard deviations of 0.63% for continuous 45 cycles) and long-term stability (∼80% of its initial ECL intensity could be retained over 3 months). More importantly, assisted by the developed ECL sensor, discrimination of 1.0 nM single-nucleotide mismatch in human urine matrix could be realized on the PCs for the first attempt. Thus, the developed sensor was confirmed with the advantages of highly sensitivity, long-term stability, simplicity, low cost, disposability, high efficiency and potential applicability.     

Growth morphology and properties of metals on graphene

Graphene, a single atomic layer of graphite, has been the focus of recent intensive studies due to its novel electronic and structural properties. Metals grown on graphene also have been of interest because of their potential use as metal contacts in graphene devices, for spintronics applications, and for catalysis. All of these applications require good understanding and control of the metal growth morphology, which in part reflects the strength of the metal–graphene bond. Also of importance is whether the interaction between graphene and metal is sufficiently strong to modify the electronic structure of graphene. In this review, we will discuss recent experimental and computational studies related to deposition of metals on graphene supported on various substrates (SiC, SiO₂, and hexagonal close-packed metal surfaces). Of specific interest are the metal–graphene interactions (adsorption energies and diffusion barriers of metal adatoms), and the crystal structures and thermal stability of the metal nanoclusters.     

Toward clean and crackless polymer-assisted transfer of CVD-grown graphene and its recent advances in GFET-based biosensors

Ever since the more than decade-old discovery of the mechanical exfoliation method for graphene isolation, this miraculous 2-dimensional material is still widely used in various applications because of its exceptional electron mobility and thermal conductivity. Graphene, commonly grown on a metallic substrate using chemical vapor deposition (CVD), needs to be transferred onto dielectric substrates compatible with complementary metal oxide–semiconductor (CMOS) technology for various electronic and optical applications. However, the ultra-clean transfer of graphene with defect-free is still crucial for large-area graphene devices' efficiency. This review introduces a comprehensive and up-to-date account of the transfer of the most attention kinds of CVD-grown graphene on copper substrates. The advances and main challenges of both wet and dry transfer methods are also carefully described. Particular emphasis is also given on graphene-based BioFET devices, revising their sensing mechanism and the optimum operational conditions toward high specificity and sensitivity. The authors have been convinced that upgrading the transfer process to accomplish the cleanest graphene surface and exploiting the optimum operating conditions will undoubtedly be of considerable significance to fabricate graphene-based devices.     

Kinetic capillary electrophoresis-based affinity screening of aptamer clones

DNA aptamers are single stranded DNA (ssDNA) molecules artificially selected from random-sequence DNA libraries for their specific binding to a certain target. DNA aptamers have a number of advantages over antibodies and promise to replace them in both diagnostic and therapeutic applications. The development of DNA aptamers involves three major stages: library enrichment, obtaining individual DNA clones, and the affinity screening of the clones. The purpose of the screening is to obtain the nucleotide sequences of aptamers and the binding parameters of their interaction with the target. Highly efficient approaches have been recently developed for the first two stages, while the third stage remained the rate-limiting one. Here, we introduce a new method for affinity screening of individual DNA aptamer clones. The proposed method amalgamates: (i) aptamer amplification by asymmetric PCR (PCR with a primer ratio different from unity), (ii) analysis of aptamer-target interaction, combining in-capillary mixing of reactants by transverse diffusion of laminar flow profiles (TDLFP) and affinity analysis using kinetic capillary electrophoresis (KCE), and (iii) sequencing of only aptamers with satisfying binding parameters. For the first time we showed that aptamer clones can be directly used in TDLFP/KCE-based affinity analysis without an additional purification step after asymmetric PCR amplification. We also demonstrated that mathematical modeling of TDLFP-based mixing allows for the determination of K_d values for the in-capillary reaction of an aptamer and a target and that the obtained K_d values can be used for the accurate affinity ranking of aptamers. The proposed method does not require the knowledge of aptamer sequences before screening, avoids lengthy (3-5 h) purification steps of aptamer clones, and minimizes reagent consumption to nanoliters.     

Evidence for Electron Transfer between Graphene and Non-Covalently Bound π-Systems

Hybridizing graphene and molecules possess a high potential for developing materials for new applications. However, new methods to characterize such hybrids must be developed. Herein, the wet-chemical non-covalent functionalization of graphene with cationic π-systems is presented and the interaction between graphene and the molecules is characterized in detail. A series of tricationic benzimidazolium salts with various steric demand and counterions was synthesized, characterized and used for the fabrication of graphene hybrids. Subsequently, the doping effects were studied. The molecules are adsorbed onto graphene and studied by Raman spectroscopy, XPS as well as ToF-SIMS. The charged π-systems show a p-doping effect on the underlying graphene. Consequently, the tricationic molecules are reduced through a partial electron transfer process from graphene, a process which is accompanied by the loss of counterions. DFT calculations support this hypothesis and the strong p-doping could be confirmed in fabricated monolayer graphene/hybrid FET devices. The results are the basis to develop sensor applications, which are based on analyte/molecule interactions and effects on doping.     

Electrochemiluminescence Based Enzymatic Urea Sensor Using Nanohybrid of Isoluminol‐gold Nanoparticle‐graphene Oxide Nanoribbons

This study evaluates on the possibility of using gold nanoparticles functionalized with the luminol derivative N‐(aminobutyl)‐N‐(ethylisoluminol) (ABEI) and hybridized with graphene oxide nanoribbons on a carbon based screen‐printed electrode (ABEI‐AuNP‐GONR/SPE) as an enzymatic electrochemiluminescence (ECL) urea sensor. The electrocatalytic activity and ECL intensity of ABEI‐AuNP‐GONR/SPE were found to increase proportionally with the concentration of urea in the analyte sample, owing to the rise in pH value. These phenomena are attributed to increased formation of luminol monoanion precursors for further electrochemical oxidation, which in turn produce either luminol radicals or excited 3‐amino‐phthalate molecules. The luminescence is most likely caused by the interaction of luminol radicals with superoxide radicals formed from dissolved oxygen. The sensitivity of our sensor was determined to be 170.58 mM⁻¹ and 16.23 mM⁻¹ for urea concentrations from 2 to 5.82 mM and from 5.82 to 30 mM, respectively, covering the normal urea level in human blood.     

Nanocomposite of bimetallic nanodendrite and reduced graphene oxide as a novel platform for molecular imprinting technology

In this present work, for the first time, we are reporting a green synthesis approach for the preparation of vinyl modified reduced graphene oxide-based magnetic and bimetallic (Fe/Ag) nanodendrite (RGO@BMNDs). Herein, the RGO@BMNDs acts as a platform for the synthesis of the pyrazinamide (PZA)-imprinted polymer matrix and used for designing of the electrochemical sensor. We have demonstrated how the change in morphology could affect the electrochemical and magnetic property of nanomaterials and for this the reduced graphene oxide-based bimetallic nanoparticle (Fe/Ag) was also prepared It was found that the combination of graphene and bimetallic nanodendrites shows improvement as well as enhancement in the electrocatalytic activity and adsorption capacity, in comparison to their respective nanoparticles. The application of imprinted-RGO@BMNDs sensor was explored for trace level detection of PZA (Limit of detection = 6.65 pg L⁻¹, S/N = 3), which is a drug used for the cure of Tuberculosis. This is lowest detection limit reported so far for the detection of PZA. The sensor is highly selective, cost-effective, simple and free from any interfering effect. The real time application of the sensor was explored by successful detection of PZA in pharmaceutical and human blood serum, plasma and urine samples.     

Chitosan/Nitrogen Doped Reduced Graphene Oxide Modified Biosensor for Impedimetric Detection of microRNA

The development of a low‐cost and disposable biosensor platform for the sensitive and rapid detection of microRNAs (miRNAs) is of great interest for healthcare, pharmaceuticals, and medical science. We designed an impedimetric biosensing platform using Chitosan (CHIT)/nitrogen doped reduced graphene oxide (NRGO) conductive composite to modify the surface of pencil graphite electrodes (PGE) for the sensitive detection of miRNAs. An initial optimisation protocol involved investigation of the effect of NRGO concentration and miR 660 DNA probe concentration on the response of the modified electrode. After the optimization protocol, the sequence‐selective hybridization between miR 660 DNA probe and its RNA target was evaluated by measuring changes on charge transfer resistance, R_ct values. Moreover, the selectivity of impedimetric biosensor was tested in the presence of non‐complementary miRNA (NC) sequences, such as miR 34a and miR 16. The hybridization process was examined both in phosphate buffer (PBS) and in PBS diluted fetal bovine serum (FBS:PBS) solutions. The biosensor demonstrated a detection limit of 1.72 μg/mL in PBS and 1.65 μg/mL in FBS:PBS diluted solution. Given the easy, quick and disposable attributes, the proposed conductive nanocomposite biosensor platform shows great promise as a low‐cost sensor kit for healthcare monitoring, clinical diagnostics, and biomedical devices.     

Intrinsic peroxidase-like catalytic activity of nitrogen-doped graphene quantum dots and their application in the colorimetric detection of H2O2 and glucose

In this paper, the highly intrinsic peroxidase-like catalytic activity of nitrogen-doped graphene quantum dots (N-GQDs) is revealed. This activity was greatly dependent on pH, temperature and H₂O₂ concentration. The experimental results showed that the stable N-GQDs could be used for the detection of H₂O₂ and glucose over a wide range of pH and temperature, offering a simple, highly selective and sensitive approach for their colorimetric sensing. The linearity between the analyte concentration and absorption ranged from 20 to 1170 μM for H₂O₂ and 25 to 375 μM for glucose with a detection limit of 5.3 μM for H₂O₂ and 16 μM for glucose. This assay was also successfully applied to the detection of glucose concentrations in diluted serum and fruit juice samples.     

基于吡嗪连接的石墨烯电极单分子场效应晶体管

In single-molecule junctions, anchoring groups that connect the central molecule to the electrodes have profound effects on the mechanical and electrical properties of devices. The mechanical strength of the anchoring groups affects the device stability, while their electronic coupling strength influences the junction conductance and the conduction polarity. To design and fabricate high-performance single-molecule devices with graphene electrodes, it is highly desirable to explore robust anchoring groups that bond the central molecule to the graphene electrodes. Condensation of ortho-phenylenediamine terminated molecules with ortho-quinone moieties at the edges of graphene generates graphene-conjugated pyrazine units that can be employed as anchoring groups for the construction of molecular junctions with graphene electrodes. In this study, we investigated the fabrication and electrical characterization of single-molecule field-effect transistors (FETs) with graphene as the electrodes, pyrazine as the anchoring groups, and a heavily doped silicon substrate as the back-gate electrode. Graphene nano-gaps were fabricated by a high-speed feedback-controlled electro-burning method, and their edges were fully oxidized; thus, there were many ortho-quinone moieties at the edges. After the deposition of phenazine molecules with ortho-phenylenediamine terminals at both ends, a large current increase was observed, indicating that molecular junctions were formed with covalent pyrazine anchoring groups. The yield of the single-molecule devices was as high as 26%, demonstrating the feasibility of pyrazine as an effective anchoring group for graphene electrodes. Our electrical measurements show that the ten fabricated devices exhibited a distinct gating effect when a back-gate voltage was applied. However, the gate dependence of the conductance varied considerably from device to device, and three types of different gate modulation behaviors, including p-type, ambipolar, and n-type conduction, were observed. Our observations can be understood using a modified single-level model that takes into account the linear dispersion of graphene near the Dirac point; the unique band structure of graphene and the coupling strength of pyrazine with the graphene electrode both crucially affect the conduction polarity of single-molecule FETs. When the coupling strength of pyrazine with the graphene electrode is weak, the highest occupied molecular orbital (HOMO) of the central molecule dominates charge transport. Depending on the gating efficiencies of the HOMO level and the graphene states, devices can exhibit p-type or ambipolar conduction. In contrast, when the coupling is strong, the redistribution of electrons around the central molecule and the graphene electrodes leads to a realignment of the molecular levels, resulting in the lowest unoccupied molecular orbital (LUMO)-dominated n-type conduction. The high yield and versatility of the pyrazine anchoring groups are beneficial for the construction of single-molecule devices with graphene electrodes.     

Effect of the Nature of the Dopant on the Response of a Sensor Array Based on Polyaniline

The effect of the nature of the dopant on the response of a sensor array based on films of polyaniline (PAn) under the influence of the vapor of various organic solvents was studied. It was established that the main factors determining the magnitude of the response of PAn films are the morphology of the films and the accepting power of the analyte molecules (in the case of "standard" acid dopants) and also the possibility of additional donor–acceptor interaction between the analyte molecules and the dopant (in the case of heteropoly acid dopants). It was shown that with heteropoly acids as dopants of PAn it is possible to increase substantially the selectivity of the response of the sensor array.     

Cauliflower‐like Platinum Particles Decorated Reduced Graphene Oxide for Sensitive Determination of Acetaminophen

Over the past years, the development of electrochemical sensing platforms for the sensitive detection of drug molecules have received great interests. In this research study, we introduced cauliflower‐like platinum particles decorated reduced graphene oxide modified glassy carbon electrode (Pt?RGO/GCE) as an electrochemical sensing platform for highly sensitive determination of acetaminophen (ACTM). The sensor was prepared via a simple and environmentally friendly two‐step electrodeposition method at room temperature. The combination of conductive RGO nanosheets and unique structured Pt particles (average 232 nm in diameter) provided an efficient interface with large effective surface area which greatly facilitated the electron transfer of ACTM. The experimental conditions that might affect the drug detection were studied in detail and optimized for best performance. The Pt?RGO/GCE was able to detect ACTM up to the limit of 2.2 nM with a linear concentration range from 0.01 to 350 μM. With its high reproducibility, excellent stability and selectivity, the as‐fabricated sensor was successfully applied to the ACTM content measurement in commercial tablets.     

Synthesis of Ferrosoferric Oxide‐graphene Oxide Nanocomposite by Isoelectric Point Method for the Detection of Catechol

Ferrosoferric oxide functionalized graphene oxide nanocomposite with layer by layer structure was synthesized by isoelectric point method in this work. The prepared material was characterized by Fourier transform infrared spectroscopy, X‐ray diffraction, scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. Then the material was used to modify a glassy carbon electrode to fabricate an electrochemical sensor for the detection of catechol. The electrochemical sensor exhibited excellent electrochemical performance towards the detection of catechol with a linear response in the range of 5–205 μM and a detection limit of 2.32 μM. Furthermore, the electrochemical sensor showed excellent selectivity, stability and repeatability. These results revealed ferrosoferric oxide functionalized graphene oxide nanocomposite has potential applications in the fabrication of electrochemical sensors.