Gain Stabilization in All-Optical Gain-Clamped Cascade of Praseodymium-Doped Fluoride Fiber Amplifiers

The authors present theoretical results of an analysis of an all-optical gain-clamped (AOGC) praseodymium-doped fluoride fiber amplifier (PDFFA) for protecting surviving channels in an amplified wavelength division multiplexed (WDM) network with six cascaded PDFFAs. The theoretical analysis is based on application of a large-signal numerical model that takes into account propagation of pump, signal, and downstream and upstream amplified spontaneous emission and includes time variation effects in a four-level laser system. It is shown that power excursions caused in an eight-channel WDM network by loss addition of six channels could be lower than 1 dB and free of relaxation oscillations if the AOGC PDFFA is strongly inverted and the total loss of the ring resonator is appropriately set.     

Suppression of Output Power and NF Excursions in Cascades of Highly Inverted EDFAs with Packet-Switched Traffic

Significant output power excursions in cascades of erbium-doped fiber amplifiers (EDFAs) can cause serious problems in wavelength division multilexing (WDM) packet-switched burst-mode networks. Signal power excursions more serious than those induced by channel addition/removal in circuit switched networks can arise when data on the WDM channels is highly variable in nature. Self-similar traffic can be subject to large variation in EDFA gain. In order to prevent unacceptable error bursts, due, for example, to channel power becoming too low to preserve adequate eye opening or exceeding thresholds for optical nonlinearities, the channel power should be maintained constant. In this letter, it is shown that the sizable power and noise figure swings arising in a cascade of EDFAs with WDM burst-mode packet-switched networks with self-similar traffic can be effectively suppressed when highly inverted amplifiers are employed. The analysis is based on the application of a numerical model, which solves the transcendental equation for length averaged metastable level population of an EDFA.     

双重瑞利散射导致的多路干涉噪声对光纤喇曼放大器噪声系数的影响

在没有对喇曼增益分布做任何假设的情况下,利用所推导的光纤喇曼放大器噪声系数的解析表达式,研究了不同光纤长度、不同信号输入功率、不同增益、不同瑞利散射下双重瑞利散射导致的多路干涉噪声对喇曼放大器噪声系数的影响.结果表明随着光纤长度,信号输入功率、喇曼增益和瑞利散射的增加,多路干涉噪声对噪声系数的劣化越严重.但通过合理的优化光纤长度、控制喇曼增益可以取得噪声和增益间的最佳平衡.     

Gain clamped L-band EDFA with forward–backward pumping scheme using fiber Bragg grating

The paper proposes a novel two stage L-band erbium doped fiber amplifier with forward–backward pumping scheme for transmission of 32 wavelength division multiplexed (WDM) channels. It is gain clamped with an in-line fiber Bragg grating (FBG) to provide flat gain over 45 nm by restricting and reutilizing amplified spontaneous emission (ASE). We demonstrate that it provides an efficient small signal gain with minimum noise figure of over 20 dB and 5.5 dB, respectively, in the L-band region (1565–1610 nm) by comparing with its forward and backward pumped counterparts with fixed Er³⁺ fiber length of 20 m for −30 dBm/channel input power. We also obtain the gain and noise figure dependence as a function of each of the Er³⁺ fiber lengths, pump power (both 1480 and 980 nm), and temperature. Hence a 10 nm region (1580–1590 nm) has been acknowledged where temperature variations become constricted for 30 °C variations (15–45 °C).     

Noise Figure Reduction in Erbium-Doped Fiber Amplifiers Using Loop Mirror Filter

Noise figure reduction of an erbium-doped fiber amplifier using loop mirror filter is demonstrated. Approximately 0.5-dB noise figure reduction is achieved at input signal power level below - 30dBm. Transferring energy from the amplifier spontaneous emission to the input signal compensates for the insertion loss of the loop mirror filter device. The insertion loss of the device approximately 1 dB.     

Systematic investigation of the avalanche effect in highly thulium-doped fiber amplifiers

The avalanche energy transfer in highly thulium doped fiber amplifiers (TDFA) pumped at 1056 nm with laser diodes was investigated. Amplified spontaneous emission (ASE) at 800 nm and 1470 nm as well as the remaining pump power were measured as function of the pump power to explain the efficiency of the energy transfer between thulium ions. As proof of our theory, fiber amplifiers based on self-made fluoride fibers doped with 2000 and 5000 ppm thulium were realized and their gain and noise figure was measured. A gain of more than 25 dB and a noise figure of less than 4 dB was achieved at a pump power of 210 mW in a TDFA using the 5000 ppm thulium fiber, whereas a gain maximum of only 5.6 dB was observed with the 2000 ppm TDF. These investigations are of special importance since until now almost all TDFAs have used 2000 ppm fibers. PACS 83.80.Ab; 32.80.Bx; 42.65.Yj     

Optimized design of two-pump fiber optical parametric amplifier and its noise characteristics

In the paper, based on the pump depleted model of two-pump fiber optical parametric amplifier (FOPA), the simulations are done to indicate the effect of amplifier parameters on gain characteristics, such as the input signal power, the wavelength separation between the two pumps, the fiber length, the nonlinear coefficient and the fourth-order dispersion of fiber. By optimizing the amplifier parameters, when FOPA attains low gain-saturation, the FOPA has a higher gain, a broader flat gain bandwidth and a lower noise figure. However, with the enhancement of gain-saturation the parametric gain decreases, the flat gain bandwidth becomes narrow and the noise figure also increases.     

Bidirectional-pumped L-band erbium-doped fiber amplifier with pump distribution technique

A dual-stage erbium doped fiber amplifier (EDFA) having a flat gain wavelength response throughout L-band transmission window is presented. By applying pump power distribution technique, the pump power is distributed to two different stages with different length of EDF depending on the coupling ratio. By controlling these two parameters, gain of 19.1 dB with small gain variation of less than 0.5 dB and a noise figure of less than 10.5 dB are achieved in this architecture using bidirectional pumping. However, when another 3 dB power coupler is added to split the pump power equally at the second stage in bidirectional, a better noise figure of less than 7.5 dB was obtained. Comparison with a conventional single-stage optical amplifier was made in order to validate the performances of this dual-stage EDFA.     

Remotely pumped hybrid double-pass L-band optical amplifier utilizing chirped fiber Bragg

This paper reported an investigation of remotely pumped double pass L-band amplifier with dispersion compensation technique. The proposed design used chirped fiber Bragg grating (CFBG) to reflect the amplified signal back into the active medium, compensate the effect of fiber dispersion and block the recycled forward amplified spontaneous emission (ASE) and the residual 1480 nm pump power. The characterization of the design was done experimentally. The gain is 37.5 dB and noise figure is 4 dB with best BER of 10⁻⁵² is achieved when the EDF is placed 150 km away from the transmitter and 48 km before the receiver terminal.     

Suppression of Output Power and NF Excursions in Cascades of Highly Inverted EDFAs with Packet-Switched Traffic

Significant output power excursions in cascades of erbium-doped fiber amplifiers (EDFAs) can cause serious problems in wavelength division multilexing (WDM) packet-switched burst-mode networks. Signal power excursions more serious than those induced by channel addition/removal in circuit switched networks can arise when data on the WDM channels is highly variable in nature. Self-similar traffic can be subject to large variation in EDFA gain. In order to prevent unacceptable error bursts, due, for example, to channel power becoming too low to preserve adequate eye opening or exceeding thresholds for optical nonlinearities, the channel power should be maintained constant. In this letter, it is shown that the sizable power and noise figure swings arising in a cascade of EDFAs with WDM burst-mode packet-switched networks with self-similar traffic can be effectively suppressed when highly inverted amplifiers are employed. The analysis is based on the application of a numerical model, which solves the transcendental equation for length averaged metastable level population of an EDFA.     

掺铒光纤放大器的理论模拟与全局分析

基于Giles模型并考虑了ASE噪音,对各种泵浦方式下的掺铒光纤放大器(EDFA)进行了数值模拟.提出了一种新的分析方法(增益噪音指数全局分析法),直观有效地分析了EDFA的增益和噪音指数与掺铒光纤长度和泵浦功率的依赖关系,并对各种EDFA的性能作了全面的比较.     

Effect of injection of C-band ASE on L-band erbium-doped fiber amplifier

The effect of injecting conventional band (C-band) amplified spontaneous emission on the performance of long-wavelength band erbium-doped fiber amplifier (L-band EDFA) is demonstrated. It uses a circulator and broadband fiber Bragg grating (FBG) to route C-band ASE from a C-band EDFA. Injection of a small amount of ASE (attenuation of 20 dB or above) improves the small signal gain with a negligible noise figure penalty compared to that of an amplifier without the ASE injection. A maximum gain improvement of 3.5 dB is obtained at an attenuation of 20 dB. At very large amounts of ASE injection (attenuation of 0 dB), the gain of the amplifier is clamped at 15.2 dB from ?40 to ?10 dBm with a gain variation of less than 0.3 dB. The saturation power is also increased from ?8 dBm (for without ASE injection) to 2 dBm (VOA=0 dB) with a slight noise figure penalty. These results show that the ASE injection technique can be used either for gain improvement or for gain clamping in L-band EDFA.     

Experimental and theoretical studies on a double-pass C-band bismuth-based erbium-doped fiber amplifier

Performance of a Bismuth-based Erbium-doped fiber amplifier is experimentally and theoretically investigated using 1480 nm pumping with double-pass scheme. In the theoretical analysis, the rate and power propagation equations are solved to examine the optimum length for the C-band operation as well as the gain and noise figure characteristics. The calculated small signal gain is 38 dB with gain variation of less than 3 dB. The measured gain is 4 dB lower due to spurious reflections which were ignored in the theoretical analysis. At input signal power of 0 dBm, a gain of 14.5 dB is obtained experimentally with gain variation of less than 1 dB within the wavelength region from 1530 to 1565 nm. The noise figure is less than 12 dB within this region.     

光纤布喇格光栅作为增益均衡器的掺铒光纤EDFA放大器

采用平均反转率模型分析了带光纤布喇格光栅的增益平坦掺铒光纤放大器,其输出增益可由一组耦合超越方程描述,而非耦合微分方程,同时讨论了用于增益平坦的布喇格光栅的最佳位置设计作为增益建模和最佳设计实例,对于输入功率0.5mW位于1545～1552nm的8个波长信道,得到的输出增益不平坦度小于0.05dB.最后还证实了布喇格光栅作为增益均衡器具有高输出功率和功率转换效率的优越性.     

双向掺铒光纤放大器的特性分析

讨论了双向掺铒光纤放大器的结构方案,利用考虑放大的自发辐和北员耗影响的双向掺铒光纤放大器稳态放大速率方程模型分析的增益与掺铒光纤长度、输入信号光功率、帛运光功率及抽运方式等参数之间的关系,研究了单向和双向等功率抽运下正反向噪声系数随正反向信号光输入功率的变化行为。     

低噪声、高增益的L -band EDFA的实验研究

针对传统的L-band EDFA的工作效率低,提出了一种基于单根光纤光栅、泵浦分配、两段级联的EDFA的新结构,其中的光纤光栅用来反射无用的后向C-band ASE.系统地研究了泵浦比例和光纤光栅波长对增益噪声指数的影响关系.最后经实验验证,得到了低噪声、高增益的L-band的EDFA.其在输入信号光（1570 nm）功率为-30 dBm及泵浦功率为70 mW时,增益为22.26 dB,增益噪声指数为4.96 dB.     

Limitation in the intrinsic method of EDFA gain optimization for 32 × 40 Gbit/s WDM systems

The gain flattening of the erbium doped fiber amplifier (EDFA) is one of the most important aspects in the EDFA which the gain is wavelength dependent. For the first time the limitation of EDFA gain optimizing for a 32-channel wavelength division multiplexing (WDM) systems is investigated and reported in this paper. In a 32-channel WDM system the most favorable flatness gain achieved was 23.16 ± 1.51 dB with an average noise figure of 5.70 dB. This outcome proposes that the method does not achieve a uniform spectral gain in a 32-channel WDM system that incorporates a bandwidth of around 25 nm. Based on the simulation results the intrinsic optimization of EDFA causes the poor SNR and peak signal power with great variation over a transmission distance of 480 km single mode fiber.     

有源循环式光脉冲复制系统的输出特性研究

改进并验证了一种基于有源循环光纤延迟线的模拟光脉冲信号复制技术.实验系统采用低增益掺铒光纤放大器补偿循环损耗.进行了光脉冲信号复制的仿真和实验,在掺铒光纤放大器增益为6.774 dB,光滤波器－3 dB,带宽为0.8 nm时,测得第500个复制光脉冲的信噪比为31 dB.仿真和实验结果表明,选用小增益掺铒光纤放大器可以实现低于3 dB的噪音系数,降低掺铒光纤放大器的放大自发辐射噪音并提高输出脉冲序列的信噪比,有望成为提高光脉冲复制器性能的一种新方法.在系统中插入窄带光滤波器等手段也是改善信噪比的有效措施.     

The L-band EDFA of high clamped gain and low noise figure implemented using fiber Bragg grating and double-pass method

The L-band erbium-doped fiber amplifier (EDFA) of low noise figure and high clamped-gain using gain-clamped and double-pass configuration is presented in this paper. A total of five different configurations of EDFAs by reflection scheme with single forward pumping schemes are examined and compared here. Among these configurations, we first find the configuration of 1480-nm pumped L-band EDFA with optimum gain and noise figure value. To further minimize the gain variation, a fiber Bragg grating (FBG) with 1615-nm center wavelength and 1-nm bandwidth is determined and added in double-pass L-band EDFA. The gain variation and maximum noise figure of EDFA while channel dropping is investigated. As the number of channel dropping from 32 to 4, the L-band type-A EDFA keep the variation of gain within 2.9 dB and the maximum noise figure below 5 dB with each channel’s input power of −23 dBm.     

基于高双折射光纤布拉格光栅的自动增益控制掺铒光纤放大器

掺铒光纤非均匀展宽引起的空间烧孔现象导致单波长激光并不能完全控制放大器增益,提出了一种新颖的自动增益控制掺铒光纤放大器的结构:即采用高双折射光纤布拉格光栅产生抽运光,其写制光栅的波峰对应的波长分别为1549.3 nm和1549.83 nm,波长间隔为0.53 nm。通过调整偏振控制器,就实现了单激光或双激光的增益控制。这种设计增益控制范围为40 nm(1530~1570 nm),当输入功率在-40~-15 dBm的动态范围内,双激光增益控制的掺铒光纤放大器的平均增益和噪声系数分别约为22.22 dB和8.69 dB,而它们的漂移分别被钳制在0.69 dB和1.51 dB。系统性能测试表明:双激光控制掺饵光纤放大器在稳定性方面比单激光有着明显的优势。