A novel electrochemical sensor based on gold nanorods and Nafion-modified GCE for the electrocatalytic oxidation of nitrite

The high-quality CTAB-stabilized gold nanorods (Au NRs) were prepared by the way of seed-mediated protocol. The microstructure and composition of the Au NRs were identified by transmission electron microscopy, field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy and UV–visible spectroscopy. Further, a novel non-enzymatic electrochemical sensor of nitrite based on Au NRs–Nafion-modified glassy carbon electrode (GCE) was successfully developed. Under the optimum experimental conditions, the electrochemical behaviors of nitrite on the Au NRs–Nafion-modified GCE were systematically studied by electrochemical impedance spectroscopy, cyclic voltammetry and chronoamperometry. The electrochemical investigations indicated that the Au NRs–Nafion-modified GCE had a wide linear range of 3.0 × 10^?6–6.0 × 10^?3 mol L^?1, an acceptable sensitivity of 130.9 ± 0.05 μA mM^?1 cm^?2, a fast response time of 3 s and a low detection limit of 0.64 ± 0.02 μmol L^?1 at the signal-to-noise ratio of 3 (S/N = 3). Additionally, the electrochemical sensor also showed good stability and favorable anti-interference capability for the detection of nitrite.     

Covalent grafting tyrosinase and its application in phenolic compounds detection

A stepwise strategy is reported for the design of a meditor-free amperometric tyrosinase biosensor. It is based on the azide-alkyne click reaction and carbodiimide coupling. Firstly, azide-terminated alkane thiols monolayers were self-assembled on the Au electrode surface. Then, nitrophenyl groups were covalent attached to the self-assembled monolayers (SAMs) via the click reaction of copper(I)-catalyzed 1,3-dipolar cycloadditions of azide-alkyne. Finally, the nitrophenyl group terminated SAMs were converted to aminophenyl-terminated interface by electrochemical reduction, and tyrosinase was covalent immobilized onto the Au electrode via carbodiimide reaction. Based on the stepwise strategy, a meditor-free amperometric tyrosinase biosensor was farbricated, and it showed good electrocatalytic reduction ability toward phenol, pyrocatechol and m-Cresol. Their linear ranges were over the range of 0.2 to 15.0 μmol·L^?1, 0.2 to 73.0 μmol·L^?1, and 0.2 to 33.0 μmol·L^?1, respectively.     

Direct Electrochemistry and Electrocatalysis of Hemoglobin/ZnO‐Chitosan/nano‐Au Modified Glassy Carbon Electrode

The highly efficient H₂O₂ biosensor was fabricated on the basis of the complex films of hemoglobin (Hb), nano ZnO, chitosan (CHIT) dispersed solution and nano Au immobilized on glassy carbon electrode (GCE). Biocompatible ZnO‐CHIT composition provided a suitable microenvironment to keep Hb bioactivity (Michaelis‐Menten constant of 0.075 mmol L^?1). The presence of nano Au in matrix could effectively enhance electron transfer between Hb and electrode. The electrochemical behaviors and effects of solution pH values were carefully examined in this paper. The (ZnO‐CHIT)‐Au‐Hb/GCE demonstrated excellently electrocatalytical ability for H₂O₂. This biosensor had a fast response to H₂O₂ less than 4 s and excellent linear relationships were obtained in the concentration range from1.94×10^?7 to 1.73×10^?3 mol L^?1 with the detection limit of 9.7×10^?8 mol L^?1 (S/N=3) under the optimum conditions. Moreover, the stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Aptamer-based Biosensor for Detection of Phenylalanine at Physiological pH

A simple, sensitive aptamer-based biosensor for the detection of phenylalanine is developed using the electrochemical transduction method. For this proposed aptasensor, a 5-thiol-terminated aptamer is covalently attached onto a gold electrode. At the first time, the electrode was evaluated as an electrochemical aptasensor for determination of phenylalanine in aqueous solutions. This sensor was tested in a Tris–HCl buffer with physiological pH?=?7.4 by cyclic voltammetry and differential pulse voltammetry. The detection limit and sensitivity of the modified electrode toward phenylalanine were estimated to be 1 nM (S/N?=?3) and 0.367 μA nM^?1, respectively. The linear range of the signal was observed between 1 and 10 nM of phenylalanine with 0.9914 correlation factor. The herein-described approach is expected to promote the exploitation of aptamer-based biosensors for protein assays in biochemical and biomedical studies.     

Determination of allura red using composites of water-dispersible reduced graphene oxide-loaded Au nanoparticles based on ionic liquid

A facile route for producing reduced graphene oxide (RGO)-loaded Au nanoparticles based on ionic liquids (IL) has been proposed, in which the as-prepared RGO can be dispersed stably in water. With the assistance of IL, Au nanoparticles were uniformly and densely absorbed on the surfaces of the IL functionalised reduced graphene oxide (IRGO), forming a new composite of IRGO/Au with high dispersibility. This IRGO/Au composite enhanced its electrochemical signal obviously in the measurement of allura red in foods and exhibited a wider linear response ranging from 0.297 (0.0006 μmol L^?1) to 99.3 μg L^?1 (0.2 μmol L^?1) with lower detection limit of 0.213 μg L^?1 (0.00043 μmol L^?1) at a signal-to-noise ratio of 3. To further study the practical applicability of the proposed sensor, the modified electrode was successfully applied to detect allura red in five kinds of common foods and the assay results were in a good agreement with the reference values detected by HPLC.     

Electrochemical application of titanium dioxide nanoparticle/gold nanoparticle/multiwalled carbon nanotube nanocomposites for nonenzymatic detection of ascorbic acid

Titanium dioxide nanoparticle/gold nanoparticle/carbon nanotube (TiO₂/Au/CNT) nanocomposites were synthesized, and then characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy (EDX). A TiO₂/Au/CNT nanocomposite-modified glassy carbon (GC) electrode was prepared using the drop coating method and was investigated using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), differential pulse voltammetry (DPV), and amperometric current–time response (I-T). The modified material is redox-active. The nonenzymatically detected amount of ascorbic acid (AA) on the TiO₂/Au/CNT electrode showed a linear relationship with the AA concentration, for concentrations from 0.01 to 0.08 μM; the sensitivity was 117,776.36 μA?·?cm^?2?·?(mM)^?1, and the detection limit was 0.01 μM (S/N?=?3). The results indicated that the TiO₂/Au/CNT nanocomposite-modified GC electrode exhibited high electrocatalytic activity toward AA. This paper describes materials consisting of a network of TiO₂, Au, and MWCNTs, and the investigation of their synergistic effects in the detection of AA.     

Amperometric Biosensors Based on Platinum Nanowires

Abstract

Platinum nanowires (PtNW) were prepared by an electrodeposition strategy using nanopore alumina template. The nanowires prepared were dispersed in chitosan (CHIT) solution and stably immobilized onto the surface of glassy carbon electrode (GCE). The electrochemical behavior of PtNW‐modified electrode and its application to the electrocatalytic reduction of hydrogen peroxide (H₂O₂) are investigated. The modified electrode allows low potential detection of hydrogen peroxide with high sensitivity and fast response time. As an application example, the glucose oxidase was immobilized onto the surface of PtNW‐modified electrode through cross‐linking by glutaric dialdehyde. The detection of glucose was performed in phosphate buffer at –0.2 V. The resulting glucose biosensor exhibited a short response time (<8 s), with a linear range of 10^?5?10^?2 M and detection limit of 5×10^?6 M.     

Synthesis of polyaniline/Au composite nanotubes and their high performance in the detection of NADH

Polyaniline (PANI)/Au composite nanotubes were synthesized and developed as an electrode material for a nicotinamide adenine dinucleotide (NADH) sensor. A MnO₂ self-degradable template method was used to prepare the tube-like PANI nanomaterial. By introducing PANI nanotubes into Au colloid, Au nanoparticles (NPs) were successfully decorated onto the surface of PANI nanotubes through electrostatic effects. The morphology, composition, and optical properties of the resulting products were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, ultraviolet-visible (UV-vis) absorption spectra, and thermogravimetric analysis (TGA). In addition, the obtained PANI/Au composites were used as catalysts for the electrochemical oxidation of NADH. Cyclic voltammogram (CV) experiments indicated that PANI/Au-modified glassy carbon electrode showed a higher electrocatalytic activity towards the oxidation of NADH in a neutral environment. Differential pulse voltammogram (DPV) results illustrated that the fabricated NADH sensor had excellent anti-interference ability and displayed a wide linear range from 4?×?10^?4 to 8?×?10^?3 M with a detection limit of 0.5?×?10^?7 M.     

Evaluation of a novel composite based on functionalized multi-walled carbon nanotube and iron phthalocyanine for electroanalytical determination of isoniazid

A novel platform for electroanalysis of isoniazid based on graphene-functionalized multi-walled carbon nanotube as support for iron phthalocyanine (FePc/f-MWCNT) has been developed. The FePc/f-MWCNT composite has been dropped on glassy carbon forming FePc/f-MWCNT/GC electrode, which is sensible for isoniazid, decreasing substantially its oxidation potential to +200 mV vs Ag/AgCl. Electrochemical and electroanalytical properties of the FePc/f-MWCNT/GC-modified electrode were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, scanning electrochemical microscopy, and amperometry. The sensor presents better performance in 0.1 mol L^?1 phosphate buffer at pH 7.4. Under optimized conditions, a linear response range from 5 to 476 μmol L^?1 was obtained with a limit of detection and sensitivity of 0.56 μmol L^?1 and 0.023 μA L μmol^?1, respectively. The relative standard deviation for 10 determinations of 100 μmol L^?1 isoniazid was 2.5%. The sensor was successfully applied for isoniazid selective determination in simulated body fluids.     

Sandwich-type amperometric immunosensor for human immunoglobulin G using antibody-adsorbed Au/SiO2 nanoparticles

A novel sandwich-type electrochemical immunosensor for human immunoglobulin G (hIgG) was developed using Au/SiO₂ nanoparticles (NPs) with adsorbed horseradish peroxidase-anti-hIgG as the secondary antibody layer. The signal readout is based on the amperometric response to the catalytic reduction of hydrogen peroxide at an AuNPs-polythionine modified glassy carbon electrode. Under optimized conditions, the linear range is from 0.1 to 200 ng·mL^?1, with a detection limit of 0.035 ng·mL^?1 (at an S/N of 3). The immunosensor exhibited a performance that is better than that based on Au/SiO₂NPs-excluded secondary antibody.     

Electrochemical determination of nonylphenol based on ionic liquid-functionalized graphene nanosheet modified glassy carbon electrode and its interaction with DNA

Nonylphenol (NP) was determined using electrochemical method based on ionic liquid-functionalized graphene nanosheet modified electrode. The fabricated electrode was characterized by electrochemical impedance spectroscopy. The different influence parameters, such as pH value, scan rate, accumulation potential, and time, were investigated. Under the optimum conditions, the linear relationship between peak current value and concentration of NP was obtained with differential pulse voltammetry in two ranges from 0.5 to 30 μM and 30 to 200 μM with the detection limit of 0.058 μM (S/N?=?3). Moreover, this modified electrode was applied to NP determination in water and soil samples with the recoveries from 94.8 to 104 %, which showed the method could be applied to determine NP in environment. In addition, to explore the damage to DNA, the interaction between NP and DNA was investigated with the association constant (β) of 0.4867 and the Hill coefficient (m) of 3.75?×?10⁵ M^?1, respectively.     

A method based on electrodeposition of reduced graphene oxide on glassy carbon electrode for sensitive detection of theophylline

Graphene nanosheets were directly electrodeposited onto a glassy carbon electrode (GCE) from the electrolyte solution containing graphene oxide (GO); the resulting electrode (ED-GO/GCE) was characterized with scanning electron microscopy. A simple and rapid electrochemical method was developed for the determination of theophylline (TP), based on the excellent properties of ED-GO film. The result indicated that ED-GO film-modified GCE exhibited efficient electrocatalytic oxidation for TP with relatively high sensitivity and stability. The electrochemical behavior of TP at ED-GO/GCE was investigated in detail. Under the optimized conditions, the oxidation peak current was proportional to the TP concentration in the range of 8.0?×?10^?7 to 6.0?×?10^?5 mol?L^?1 with the detection limit of 1.0?×?10^?7 mol?L^?1 (S/N?=?3). The proposed method was successfully applied to green tea samples with satisfactory results.     

Label-Free Detection of DNA Hybridization Based on MnO2 Nanoparticles

Abstract

Nano-MnO₂/chitosan composite film modified glassy carbon electrode (MnO₂/CHIT/GCE) was fabricated and a DNA probe was immobilized on the electrode surface. The immobilization and hybridization events of DNA were characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The EIS was applied to the label-free detection of the target DNA. The human immunodeficiency virus (HIV) gene fragment was successfully detected by this DNA electrochemical sensor. The dynamic detection range was from 2.0 × 10^?11 to 2.0 × 10^?6 mol/L, with a detection limit of 1.0 × 10^?12 mol/L.     

Sensitive voltammetric determination of rutin at a carbon nanotubes-ionic liquid composite electrode

A new composite electrode of multiwall carbon nanotubes (MWNTs) and 1-dodecyl-3-methylimidazolium hexafluorophosphate (DDMIMPF₆) was fabricated to determine rutin. This electrode showed very attractive electrochemical performances compared to other kinds of ionic liquid modified electrodes and notably improved sensitivity and stability. Electrochemical behavior of rutin at the composite electrode had been investigated in pH 2.09 Britton–Robinson buffer solution by cyclic voltammetry and square wave voltammetry. The experimental results suggested that the composite electrode exhibited an electrocatalytic activity toward the redox of rutin. The electrochemical parameters of rutin were calculated with the results of the charge transfer coefficient (α) and the standard rate constant (k _s) as 0.48 and 2.09 s^?1. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of rutin in the range of 0.03–1.5 μM, with a detection limit of 0.01 μM (S/N?=?3). The relative standard deviation for six times successive determination of 1 μM rutin was 1.6 %. The method was successfully applied to the determination of rutin in tablets and urine samples without the influence of the coexisting substances. In addition, the MWNTs/DDMIMPF₆ composite electrode exhibits a distinct advantage of simple preparation, surface renewal, good reproducibility, and stability.     

Direct electrochemistry of double stranded DNA on ionic liquid modified carbon paste electrode

The direct electrochemistry of herring sperm double-stranded DNA (dsDNA) on an ionic liquid N-butylpyridinium hexafluorophosphate modified carbon paste electrode was investigated. The cyclic voltammogram showed two irreversible oxidation peaks at 0.868 V and 1.188 V (vs. SCE), which corresponded to the oxidation of guanine and adenine residues, respectively. Compared to the common carbon paste electrode the electrochemical response was greatly improved. The electrochemical behavior of dsDNA on the modified electrode was carefully investigated with the electrochemical parameters were calculated. Under optimal conditions the dsDNA can be directly determined in the concentration range from 50 to 600 μg mL^?1 with a detection limit of 17 μg mL^?1 (3σ).     

Electrochemical sensor for determination of aflatoxin B1 based on multiwalled carbon nanotubes-supported Au/Pt bimetallic nanoparticles

A sensitive and selective imprinted electrochemical sensor for the determination of aflatoxin B₁ (AFB₁) was constructed on a glassy carbon electrode by stepwise modification of functional multiwalled carbon nanotubes (MCNTs), Au/Pt bimetallic nanoparticles (Au/PtNPs), and a thin imprinted film. The fabrication of a homogeneous porous poly o-phenylenediamine (POPD)-grafted Au/Pt bimetallic multiwalled carbon nanotubes nanocomposite film was conducted by controllable electrodepositing technology. The sensitivity of the sensor was improved greatly because of the nanocomposite functional layer; the proposed sensor exhibited excellent selectivity toward AFB₁ owing to the porous molecular imprinted polymer (MIP) film. The surface morphologies of the modified electrodes were characterized using a scanning electron microscope. The performance of the imprinted sensor was investigated by cyclic voltammetry, differential pulse voltammetry, and electrochemical impedance spectroscopy in detail. A linear relationship between the sensor response signal and the logarithm of AFB₁ concentrations ranging from 1?×?10^?10 to 1?×?10^?5 mol L^?1 was obtained with a detection limit of 0.03 nmol L^?1. It was applied to detect AFB₁ in hogwash oil successfully.     

Tantalum Electrodes Modified With Well-Aligned Carbon Nanotube–Au Nanoparticles: Application to the Highly Sensitive Electrochemical Determination of Cefazolin

Carbon nanotube/nanoparticle hybrid materials have been proven to exhibit high electrocatalytic activity suggesting broad potential applications in the field of electroanalysis. For the first time, modification of Ta electrode with aligned multi-walled carbon nanotubes/Au nanoparticles introduced for the sensitive determination of the antibiotic drug, cefazolin (CFZ). The electrochemical response characteristics of the modified electrode toward CFZ were investigated by means of cyclic and linear sweep voltammetry. The modified electrode showed an efficient catalytic activity for the reduction of CFZ, leading to a remarkable decrease in reduction overpotential and a significant increase of peak current. Under optimum conditions, the highly sensitive modified electrode showed a wide linear range from 50 pM to 50 μM with a sufficiently low detection limit of 1?±?0.01 pM (S/N?=?3). The results indicated that the prepared electrode presents suitable characteristics in terms of sensitivity (458.2?±?2.6 μAcm^?2/μM), accuracy, repeatability (RSD of 1.8 %), reproducibility (RSD of 2.9 %), stability (14 days), and good catalytic activity in physiological conditions. The method was successfully applied for accurate determination of trace amounts of CFZ in pharmaceutical and clinical preparations without the necessity for samples pretreatment or any time-consuming extraction or evaporation steps prior to the analysis.     

Selective determination of L-dopa in the presence of ascorbic acid and uric acid using a 3D graphene foam

Three-dimensional interconnected network graphene foam (GF) was synthesized by chemical vapor deposition. The GF was transferred onto indium tin oxide glass, acting as an electrode for the selective determination of L-dopa in the presence of ascorbic and uric acid. Using differential pulse voltammetry (DPV) method, the oxidation peak current is well linear with L-dopa concentration in the range of 0.05–1 μM with a sensitivity of 2.64 μA μM^?1 and in the range of 1–40 μM with a sensitivity of 1.82 μA μM^?1. The detection limit of this electrode for L-dopa is about 20 nM. The proposed electrode can also effectively avoid the interference of ascorbic acid and uric acid, making the proposed sensor suitable for the accurate determination of L-dopa in human urine fluids. This electrode will have a wide range of potential application prospect in electrochemical detection.     

Electrocatalytic determination of propranolol hydrochloride at carbon paste electrode based on multiwalled carbon-nanotubes and γ-cyclodextrin

A carbon paste electrode based on γ-cyclodextrin–carbon nanotube composite (γ-CD–CNT–CME) was developed for the determination of propranolol hydrochloride (PRO). The electrochemical behaviour of PRO was investigated employing cyclic voltammetry, electrochemical impedance spectroscopy and differential pulse adsorptive stripping voltammetry (DPAdSV). Surface morphology of the electrode has been studied by means of scanning electron microscopy. The results revealed that the oxidation of PRO is facilitated at γ-CD–CNT–CME. Under the optimized conditions in Britton–Robinson buffer pH 1.5, the peak currents were found to vary linearly with their concentrations in the range of 1.42 × 10^?7 to 4.76 × 10^?5 M. A detection limit (S/N = 3) of 4.01 × 10^?8 M was obtained for PRO by means of DPAdSV. The proposed method was employed for the determination of PRO in pharmaceutical formulations, urine and blood serum samples.     

Supramolecular immobilization of glucose oxidase on gold coated with cyclodextrin-modified cysteamine core PAMAM G-4 dendron/Pt nanoparticles for mediatorless biosensor design

Cysteamine core polyamidoamine G-4 dendron branched with β-cyclodextrins was chemisorbed on the surface of Au electrodes and further coated with Pt nanoparticles. Adamantane-modified glucose oxidase was subsequently immobilized on the nanostructured electrode surface by supramolecular association. This enzyme electrode was used to construct a reagentless amperometric biosensor for glucose, making use of the electrochemical oxidation of H₂O₂ generated in the enzyme reaction. The amperometric response of the biosensor was rapid (6 s) and a linear function of glucose concentration between 5 and 705 μmol?L^?1. The biosensor had a low detection limit of 2.0 μmol?L^?1, sensitivity of 197 mA?mol^?1?L?cm^?2, and retained 94 % of its initial response after storage for nine days at 4 °C.