Grafting of molecularly imprinted polymer to porous polyethylene filtration membranes by plasma polymerization

An application of plasma-induced grafting of polyethylene membranes with a thin layer of molecularly imprinted polymer (MIP) was presented. High-density polyethylene (HDPE) membranes, “Vyon,” were used as a substrate for plasma grafting modification. The herbicide atrazine, one of the most popular targets of the molecular imprinting, was chosen as a template. The parameters of the plasma treatment were optimized in order to achieve a good balance between polymerization and ablation processes. Modified HDPE membranes were characterized, and the presence of the grafted polymeric layer was confirmed based on the observed weight gain, pore size measurements, and infrared spectrometry. Since there was no significant change in the porosity of the modified membranes, it was assumed that only a thin layer of the polymer was introduced on the surface. The experiments on the re-binding of the template atrazine to the membranes modified with MIP and blank polymers were performed. HDPE membranes which were grafted with polymer using continuous plasma polymerization demonstrated the best result which was expressed in an imprinted factor equal to 3, suggesting that molecular imprinting was successfully achieved.

Au nanolayers deposited on polyethyleneterephtalate and polytetrafluorethylene degraded by plasma discharge

Polyethyleneterephtalate (PET) and polytetrafluorethylene (PTFE) foils were modified by plasma discharge. The effect of plasma modification on polymer surface wettability and on properties of gold coatings were studied as a function of time from plasma exposure (aging time) and polymer substrate temperature. Thickness, sheet resistance, and surface topology of gold layers were studied. Aging of the plasma‐exposed samples is accompanied by increase in contact angle, which is explained by rearrangement of the polymer segments in the polymer surface monolayer, and a decrease in the concentration of polar groups. The aging also leads to a decline in surface roughness R_a measured by atomic force microscopy (AFM). Under deposition conditions, comparable thicknesses of deposited Au layers were prepared on pristine PET and plasma‐treated PET and PTFE samples. The thinnest Au layers were evaporated onto pristine PTFE. The sheet resistance decreases with increasing thickness of Au layer. Plasma treatment leads to an increase of PTFE surface roughness, which becomes even more pronounced after Au deposition. A higher roughness shows that the PET samples are deposited with the Au layer at temperatures above the glassy transition temperature T_g. Copyright © 2006 John Wiley & Sons, Ltd.     

紫外光引发LDPE膜接枝含氟丙烯酸酯的研究

通过紫外光引发表面接枝聚合反应的方法 ,把含氟丙烯酸酯单体R 5 6 1 0引到LDPE薄膜上 .对经丁酮抽提后的接枝膜进行FTIR、ESCA、SEM和DSC等表征 ,证实含氟聚合物以化学键的方式接枝在LDPE基体膜上 .在一定范围内 ,增加紫外光强、引发剂和单体浓度以及反应温度等均有利于提高接枝率 .经计算R 5 6 1 0的紫外光引发接枝聚合反应总活化能为 5 4 2kJ mol.接枝膜的接触角随着接枝率的提高逐步增大 ,直至趋于恒定 .作者提出接枝膜存在一个在接触角测定时影响基体膜与探测水滴相互作用过程的边界层 .当接枝率较低、接枝层厚度小于边界层临界厚度时 ,基体LDPE影响接触角的大小 ,但随着接枝率提高 ,接枝层逐渐变厚 ,氟聚合物层对接触角的贡献逐渐占优势 ,导致接触角随之增大 .当接枝率超过一定值以后 ,接枝层厚度超过边界层临界厚度 ,接枝层对接枝膜的接触角起全部贡献 ,接触角测定值随之稳定     

氧等离子体改性聚乙烯表面的疏水性过回复机制

用200 W射频容性耦合氧等离子体处理低密度聚乙烯(LDPE)表面1 min, 研究了老化温度及时间对LDPE表面成分、 形貌和润湿性的影响. 扫描电子显微镜结果表明, 等离子体改性LDPE表面出现纳米凸点织构, 在60和90 ℃老化24 h后纳米凸点织构特征基本保持稳定. X射线光电子能谱分析表明, 等离子体改性LDPE表面经60 ℃老化24 h后, C—C含量由76.9%增至83.0%, C—O, CO和O—CO含量分别由16.4%, 2.2%和4.5%降至13.1%, 1.9%和2.0%. 经90 ℃老化24 h后, C—C含量较60 ℃老化表面增至84.1%, C—O含量分别降至10.1%, CO和O—CO含量分别增至3.1%和2.7%. 等离子体改性LDPE表面接触角由97.2°降至42.3°, 经60 ℃老化24 h后接触角增至95.9°, 经90 ℃老化24 h后接触角增至104.2°, 等离子体改性LDPE表面发生“疏水性过回复”. 根据含有粗糙因子的接触角随时间演变模型, 得到了具有纳米凸点织构LDPE表面在不同老化温度下的可移动极性基团所占面积分数(\begin{array}{c}{f}_m^p\end{array})、 固定极性基团所占面积分数(\begin{array}{c}{f}_{\mathit{im}}^p\end{array})和特征时间常数(τ)3个成分重构参数, 解释了“疏水性过回复”现象.     

Water barrier characteristics of plasma polymers of perfluorocarbons

Perfluorocarbon monomers such as C₂F₄, C₂F₆, C₄F₁₀, and mixtures thereof with H₂, were subjected to plasma polymerization and deposited onto low-density polyethylene (LDPE) substrates. The effect of plasma conditions, surface characteristics, and surface dynamics of plasma polymers on their ability to improve the resistance to water vapor permeation was investigated. An optimum discharge energy density was found for a monomer which provided the greatest reduction water vapor permeability. Although all of the plasma polymers show higher hydrophobicity than polyethylene, the reduction in water vapor permeability is not uniquely related to water contact angle. The surface-dynamic stability of a plasma polymer surface was found to be the key factor in determining the barrier performance of the plasma polymer. The extent of change of surface-configuration after water immersion strongly correlated with the improvement in the water vapor permeation resistance. Plasma polymers with the higher surface-dynamic stability provided the better water barrier coating applied on LDPE films. © 1996 John Wiley & Sons, Inc.     

Low‐Density Polyethylene Superhydrophobic Surface by Control of Its Crystallization Behavior

Summary: A simple and inexpensive method for forming a low‐density polyethylene (LDPE) superhydrophobic surface by controlling the crystallization behavior of LDPE by adjusting the crystallization time and nucleation rate has been proposed. The resulting porous surface, with hierarchical micro‐ and nanostructures on the beautiful floral designs, has a water contact angle of 173.0° ± 2.5°.

A highly porous surface created by adding nonsolvent (cyclohexanone) followed by evaporation of the LDPE in a vacuum at 25 °C (left, inset shows corresponding water contact angle). Nanostructures on the florallike crystal structures (right).     

Thermal Conductivity of Nanocomposites Based in High Density Polyethylene and Surface Modified Hexagonal Boron Nitride via Cold Ethylene Plasma

Hexagonal boron nitride nanoparticles (hBN) were surface modified by treatment with cold ethylene plasma. During this treatment, an ultrathin plasma polymerized polyethylene layer is deposited on the surface of the hBN nanoparticles. Before and after the plasma treatment, the nanoparticles were characterized by infra-red spectroscopy, thermogravimetric analysis, transmission electron microscopy (TEM) and X-ray diffraction. Untreated and plasma treated nanoparticles were incorporated via melt mixing into high density polyethylene (HDPE), at different concentrations. Dispersion of hBN within the polymer and the polymer-particle interaction were studied by TEM. Thermal conductivity of the prepared nanocomposites was determined by modulated differential scanning calorimetry. In general, the thermal conductivity of all HDPE–hBN prepared nanocomposites was higher than that of pure HDPE. However, the higher conductivity values, 97 and 114% higher than that of pure HDPE, were obtained in plasma treated samples (treated at 100 W for 5 min) with 8 and 15 wt% loading of hBN.     

Surface properties of polyethylene after low-temperature plasma treatment

The effect of oxygen and ammonia plasma treatments on changes of the surface properties of linear high-density polyethylene (HDPE) was studied. Surface energies of the polymer substrates were evaluated by contact angle measurements using Lifshitz-van der Waals acid-base approach. The surface energy of untreated HDPE is mainly contributed by Lifshitz-van der Waals interactions. After 5 min of plasma treatment, hydrogen bonds are formed on the surface, which is reflected in predominant acid-base interactions. The SEM results obtained demonstrate considerable changes of the surface roughness due to different types of the plasma gas used. Evolution of oxygen- or amino-containing moieties was detected by XPS and ATR FT IR. The prepared polyethylene surfaces were used as a basic support for further fabrication of novel hybrid biocomposite sandwich structures.     

Low-pressure plasma chlorination of styrene-butadiene block copolymer for improved adhesion to polyurethane adhesives

Studies concerning plasma-surface chlorination of a styrene-butadiene block copolymer (SBS), improving its adhesion to polyurethane adhesives (PU), are presented in this paper. The plasma was generated by an RF discharge (13.56 MHz, plate electrode reactor) in CCl₄ under low pressure. The 180°-peel test, contact angle measurements and XPS spectroscopy were utilized to investigate the SBS surface. A drastic increase in the adhesion (the peel strength 5-7 times higher than that for the non-treated surface) was observed after only a few seconds of the plasma treatment. It was shown that CCl, COH and >CO are the most important functional groups formed as a result of the plasma treatment and they play the crucial role in the chemical bonding between the SBS surface and the adhesive. H₂O molecules strongly attached to the SBS surface were also found. It was determined, however, that they reduce the gluing power. A very good correlation between the concentration of the functional groups and the peel strength was established. On the other hand, no correlation between the peel strength and the surface free energy (estimated from the contact angle measurements) was observed. It indicates that the thermodynamic adhesion is unimportant in this case and confirms the dominant role of the chemical adhesion.     

The competitive ablation and polymerization (CAP) principle and the plasma sensitivity of elements in plasma polymerization and treatment

The competitive ablation and polymerization (CAP) principle relates the ablation of materials in plasma to the deposition of materials in plasma. Plasma polymerization and plasma treatment cannot be elucidated without consideration of the fragmentation of molecules in both the gas and solid phases. The general fragmentation tendency follows a plasma sensitivity series of the elements involved that is based on element electronegativity. When consecutive plasma treatments, sequential plasma polymerization, or a combination of plasma treatment and plasma polymerization are carried out in the same reactor, factors that are often not considered in an ordinary individual process become crucial. The CAP principle and the concept of a plasma sensitivity series of the elements explain the rather complicated and interrelated influences of fragmented elements in the plasma deposition of materials. Plasma polymers should be considered a mixture of oligomers and polymeric networks. The oligomer content in a plasma‐polymerized layer is vitally important to the adhesion of the plasma polymer to the substrate as well as to any subsequent coating applied to the layer of the plasma polymer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 943–953, 2000     

Macromolecular scission and crosslinking rate changes during polyolefin photo-oxidation

Chain scission and crosslinking rates have been derived from molecular mass distributions obtained by gel permeation chromatography at different stages during photodegradation of various thermoplastics exposed to ultraviolet irradiation (UV). Results are given for a high density polyethylene (HDPE); a low density polyethylene (LDPE); a linear low density polyethylene (LLDPE); a polypropylene homopolymer (PPHO); and a polypropylene copolymer (PPCO). As the oxidation progressed, it was observed that the scission rate for HDPE, LLDPE, PPHO and PPCO increased near to the exposed surface whereas for LDPE the rate remained almost unchanged. The crosslink rate fell near to the surface with HDPE and LDPE but increased with PPHO and PPCO. The reaction rates near to the bar centre (∼1.5 mm from the exposed surface) were low for HDPE, PPHO and PPCO; this is attributed to oxygen starvation, caused by consumption of oxygen by rapid reaction near the surface. Reaction was observed in the interior with LDPE and LLDPE, presumably because of a combination of a higher oxygen diffusion rate than for HDPE and a lower rate of consumption of oxygen near the surface than with the polypropylenes.     

Degradation of pre-aged polymers exposed to simulated recycling: Properties and thermal stability

Accelerated thermal and photo-aging of four homopolymers, low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and high-impact polystyrene (HIPS), was performed and the impact of subsequent reprocessing conditions on their properties studied. Polymer samples oven-aged at 100 °C for varying periods of time or UV irradiated in a Weather-o-meter (WOM) at λ = 340 nm were reprocessed in a Brabender plasticorder at 190 °C/60 rpm for 10 min. Chemical changes and the evolution of rheological and mechanical properties accompanying the gradual degradation of the individual polymers were monitored and evaluated (DSC, FTIR, colorimetric method, MFI, tensile impact strength). LDPE and HIPS were found to be more susceptible to thermo-oxidation than HDPE and PP, whereas HDPE and PP were affected to a greater extent by UV exposure; the crucial role here is being played by the stabilization of the studied resins. In HDPE the scission and crosslinking reactions competed both in thermo-and photo-degradation. In the case of LDPE, scission prevailed over branching during thermo-oxidation, whereas photo-oxidation of the same sample led predominantly to crosslinking. Abrupt deterioration of the LDPE rheological properties after one week of thermal exposure was suppressed by re-stabilization. The scission reaction was also predominant for PP during thermo-oxidation, and it took place even faster during UV exposure. In the case of HIPS a slight photo-degradation of PS matrix is accompanied by simultaneous crosslinking of the polybutadiene component.     

Effects of Atmospheric Plasma Pretreatments on Pectinase Efficiency in Bioscouring of Linen Fabrics

Pectinase enzyme treatment subsequent to atmospheric air- or argon-plasma surface modification was applied in linen fabric preparation. Wettability by water drop test, wickability by thin layer wicking experiment, residual pectin content and colour of the fabrics were characterized. Results clearly proved that the efficiency of pectinase in improving linen water absorbency can be significantly enhanced by plasma pretreatment. Argon-plasma pretreatment followed by a Beisol PRO enzyme treatment reduced the wetting time considerably and resulted in a fabric surface that has been characterized by the lowest water contact angle (86.6??). All the applied treatments increased the energy of the fibre surface. The alkaline scoured, the argon-plasma treated and the argon-plasma-pectinase treated samples have been characterized by the highest $ \gamma_{S}^{total} $ values. Plasma treatment significantly decreased the whiteness and increased the yellowness of the raw fabrics. However, the enzyme treatment applied after the plasma treatment has overcome the colour differences.     

Photochemical grafting of polysulfobetaine onto polyethylene and polystyrene surfaces and investigation of long‐term stability of the polysulfobetaine layer in seawater

Low‐density polyethylene (LDPE) and polystyrene (PS) films with hydrophilic surface were prepared by photochemical grafting of sulfobetaine‐based copolymer containing photolabile moiety, and long‐term stability of the hydrophilic nature of the surfaces in seawater was proved. The sulfobetaine‐based copolymer was prepared by copolymerization of N,N‐dimethyl‐N‐(3‐(methacryloylamino)propyl)‐N‐(3‐sulfopropyl) ammonium betaine with 2 or 5 mol% of N‐methacryloyl‐4‐azidoaniline, and the resulted polymers were grafted onto the plasma pretreated LDPE and PS films. The contact angle measurements were used to prove the modification as well as to follow the changes in the hydrophilicity during storage at room temperature under air atmosphere as well as in seawater at 32°C. The stability of the polymer layer was confirmed also by FTIR and AFM. Polysulfobetaine‐modified LDPE and PS surfaces exhibited significantly higher long‐term hydrophilicity compared with only plasma treated LDPE and PS surfaces.     

Effect of environment on the degradation of starch and pro-oxidant blended polyolefins

The aim of this study was to understand the rate of degradation of commercial pro-oxidant blended and starch blended High Density Polyethylene (HDPE), pro-oxidant blended Low Density Polyethylene (LDPE), and starch blended polypropylene in three different environments, namely under direct sunlight, buried in soil and immersed in marine waters for a period of 150 days. The bio-fouling parameters were also monitored in the case of polymers deployed in sea water. Exposure to sunlight showed highest weight loss (>10%) and samples buried in soil showed the lowest (∼1%). Pro-oxidant blended HDPE showed higher weight loss when compared to starch blended (22.7 as against 11%). Scanning electron microscopy revealed surface deterioration and decrease in contact angle indicated reduction in surface hydrophobicity. Increase in the carbonyl and hydroxyl groups in the infra-red spectrum of the exposed samples suggested abiotic degradation. Starch blended PP exposed to sunlight showed the highest thermo gravimetric weight loss (63.8%) followed by the same polymer buried in soil (46.1%).     

Barrier properties of polymer/alumina nanocomposite membranes fabricated by atomic layer deposition

Novel polymer/ceramic nanocomposite membranes were fabricated, characterized and tested for their barrier performance. Atomic layer deposition (ALD) was used to deposit alumina films on primary, micron-sized (16 and 60 μm) high-density polyethylene (HDPE) particles at a rate of 0.5 nm/cycle at 77 °C. Well-dispersed polymer/ceramic nanocomposites were obtained by extruding alumina coated HDPE particles. The dispersion of alumina flakes can be controlled by varying the number of ALD coating cycles and substrate polymer particle size. The diffusion coefficient of fabricated nanocomposite membranes can be reduced to half with the inclusion of 7.29 vol.% alumina flakes. However, a corresponding increase in permeability was also observed due to the voids formed at or near the interface of the polymer and alumina flakes during the extrusion process, as evidenced by electron microscopy. The low surface wettability of the alumina outerlayers was believed to be one of the main reasons of void formation. Particle surface wettability was improved using 3-aminopropyltriethoxysilane (APS) to coat the particle ALD surface modified polymer particles prior to extrusion. The diffusion coefficient and permeability of the membrane using surfactant-modified particles decreased by 20%, relative to the non-modified case.     

Analysis of the area of material really tested by TMA

Deformation distribution within the specimen beneath the thermomechanical analysis (TMA) probe, found by using the finite element method (FEM), depends mainly on penetration depth, specimen thickness and diameter as well as on radius of the probe tip when the Poisson’s ratio influences it just slightly. For standard radius of the tip R_o=1 mm, most deformation is distributed in a material layer up to 0.5 mm thick independently on elastic modulus of a polymer at a glassy state. It is caused by the fact that maximal penetration depth for the polymers usually equals to about 0.05 mm. Because of this, the contact surface area is less than 0.17 mm² for the standard radius of the tip. This evidences that predominantly the specimen volume equal to  mm² (depth×area) is tested by the TMA at compression mode. For R_o=5 mm is tested the layer 2.5 mm thick. This makes possible to evaluate the material properties in the zone of different thickness depending on radius of the tip.     

Oxygen permeability of novel organic-inorganic coatings: II. Modification of the organic component with a hydrogen-bond forming polymer

The oxygen permeability of composite materials, consisting of a LDPE substrate coated with a thin layer (0.7-1 μm) of new hybrid organic/inorganic materials based on SiO₂ and PE-PEG block copolymers, has been characterized at 35 and 50 °C. The effect of adding a second organic component capable to form hydrogen bonds, namely either poly(4-hydroxystyrene) (PHS) or malic acid, has been studied. While the addition of PHS leads to a further significant decrease (50-70%) of the oxygen permeability both at 35 and 50 °C, on the contrary, the addition of malic acid leads to poorer barrier properties. A slight decrease of the permeability was obtained after plasma treatment of the LDPE surface.