嵌段共聚物OSM1-PCLA-PEG-PCLA-OSM1的合成及其pH和温度敏感性

采用开环聚合法和自由基聚合法合成了生物可降解嵌段共聚物OSM1-PCLA-PEG-PCLA-OSM1, 并对其进行了结构表征. 采用荧光分光光度计和激光粒度仪对共聚物溶液临界胶束浓度(CMC)和粒径大小及分布进行了考察, 研究了温度和pH对共聚物胶束形成的影响. 相转变过程研究结果表明, 共聚物溶液具有pH和温度双重敏感性. 共聚物溶液在一定温度和pH条件下可发生溶液-凝胶相转变.     

磷酰胆碱基pH敏感性ABA型嵌段共聚物的合成与胶束化

采用氯化亚铜/2,2-联二吡啶催化体系, 2,5-二溴己二酸二乙酯为引发剂, 甲醇为溶剂运用希莱克技术, 利用原子转移自由基聚合(ATRP)方法合成了ABA型三嵌段共聚物PDEAEMA-b-PMPC-b-PDEAEMA. ¹H NMR和GPC(凝胶渗透色谱)对聚合物组成、结构及分子量进行了表征, 利用透光率、粘度测定研究了嵌段共聚物溶液的pH敏感性, 利用表面张力测定、荧光探针和透射电镜研究了嵌段共聚物胶束化作用, 确定了共聚物水溶液的临界胶束浓度(CMC). 结果表明所合成的ABA型三嵌段共聚物水溶液具有pH敏感性, 其临界相变pH 7～7.5. 调节溶液pH值可实现嵌段共聚物胶束化形成“花状”胶束, 并测定了其临界胶束浓度.     

不同嵌段比的PEG-b-PDMAEMA共聚物在水溶液中的自聚集行为

采用氢核磁共振(¹H-NMR)、动态光散射(DLS)及透射电子显微镜(TEM)对聚乙二醇-嵌段-聚甲基丙烯酸N,N-二甲氨基乙酯(PEG-b-PDMAEMA)三种具有不同PEG/PDMAEMA嵌段比的PEG-b-PDMAEMA共聚物在水溶液中的自聚集行为进行了研究. 研究表明, 两嵌段比例是影响聚合物胶束化过程的关键因素: 只有当其中聚乙二醇含量较低(质量分数低于33%)时, 聚合物才具有其pH/温度敏感胶束化特性. 此外, 共聚物溶液随温度胶束化过程与共聚物嵌段比大小密切相关. PEG-b-PDMAEMA这种不同于传统双亲性嵌段共聚物(DHBCs)在选择性溶剂中独特的胶束化行为, 是由聚合物溶液体系中各种基团之间的氢键作用决定的.     

疏水化修饰的聚N-异丙基丙烯酰胺高分子的水溶液性质研究

为了研究不同疏水化修饰的聚Ｎ 异丙基丙烯酰胺（ＰＮＩＰＡＭ）高分子的水溶液性质,合成了一系列Ｎ 异丙基丙烯酰胺（ＮＩＰＡＭ）和长链丙烯酸酯及丙烯酸胆固醇酯的共聚物．利用表面张力法证实了该类共聚物在室温下都具有良好的表面活性,在水溶液中能够形成胶束．利用荧光探针法,研究了共聚物的低温临界溶液温度（ＬｏｗｅｒＣｒｉｔｉｃａｌＳｏｌｕｔｉｏｎＴｅｍｐｅｒａｔｕｒｅ,ＬＣＳＴ）,发现,随着丙烯酸酯碳链及其配比（摩尔投料比）的变化,共聚物的ＬＣＳＴ变化不明显,但它们都比均聚的ＰＮＩＰＡＭ要低;利用荧光偏振法研究了共聚物在水溶液中的微粘度,发现其微粘度不随共聚物中丙烯酸酯链长和配比的变化而变化,说明了该类共聚物在室温下能够形成相类同的胶束内核．     

超支化聚乙烯亚胺-聚天冬氨酸苄酯共聚物的制备及性能

以超支化聚合物聚乙烯亚胺为引发剂, 天冬氨酸苄酯-NCA为单体, 利用热开环聚合法合成了超支化聚乙烯亚胺-聚天冬氨酸苄酯共聚物(PEI-PBLA). 用核磁共振波谱对PEI-PBLA的化学结构进行了表征. 研究了PEI-PBLA在水溶液及有机溶液中的自组装行为. 以芘为荧光探针测定了共聚物在水中形成胶束的临界胶束浓度. 以甲基橙为客体分子, 研究了共聚物胶束的包覆能力, 结果表明, 共聚物对客体分子的吸附与溶液的pH值有关. 研究了共聚物与质粒DNA的复合发现, PEI-PBLA能够很好地与质粒DNA复合, 并且可以避免DNA酶的降解, 对其起到一定的保护作用. 此聚合物在药物传输、可控释放及基因载体等方面都有着潜在的应用价值.     

温度/pH敏感性嵌段共聚物P(HEMA-co-DEAEMA)-b-PDEAM-b-P(DEAEMA-co-HEMA)的合成与性质研究

利用原子转移自由基聚合方法(ATRP)合成了组成递变的嵌段共聚物P(HEMA-co-DEAEMA)-b-PDEAM-b- P(DEAEMA-co-HEMA). 用FTIR, ¹H NMR和GPC技术表征了聚合物的组成、结构、分子量及其分布. 通过透光率测定、粘度、激光粒度分析和透射电镜研究了共聚物组成、温度及溶液pH对其溶液相行为和胶束化作用的影响. 结果表明: 所合成的嵌段共聚物具有温度和pH敏感性, 共聚物水溶液的低临界溶解温度(LCST)随HEMA量的增加而降低, 临界相变pH随HEMA量的增加而降低, 温度和pH诱导均可实现嵌段共聚物的胶束化. 控制HEMA量可以调控嵌段共聚物的LCST和pK_a.     

表面活性剂对纤维素接枝共聚物溶液粘度性质的影响

研究了阴离子十二烷基硫酸钠(SDS)、阳离子十六烷基三甲基溴化铵(CTAB)和非离子聚乙二醇辛基苯基醚(OP)等三种不同类型的表面活性剂对疏水化水溶性两性纤维素接枝共聚物(CGAO)溶液粘度性质的影响.结果表明,在SDS和OP的临界胶束浓度(cmc)附近，CGAO溶液粘度最大，SDS引起CGAO粘度的变化大于OP；即使在CTAB的cmc附近，随着CTAB浓度的增加，CGAO的粘度一直呈下降趋势；非疏水改性的纤维素接枝共聚物的溶液粘度随SDS或CTAB浓度的增加而下降，但几乎不随OP浓度的增大而变化.此外，通过凝胶渗透色谱法测得的保留时间证实了SDS、CTAB和OP与CGAO之间的疏水缔合作用.     

表面张力法研究温敏性接枝共聚物的微胶束化行为

用表面张力法研究了以水溶性可生物降解的葡聚糖为主链 ,具有温敏相变特性的聚 (N 异丙基丙烯酰胺 )为接枝链的葡聚糖 接枝 聚 (N 异丙基丙烯酰胺 ) (Dextran g PNIPAM)共聚物在水溶液中的胶束化行为 .研究结果表明Dextran g PNIPAM体系的微胶束化行为与共聚物结构和溶液体系的温度密切相关 ,接枝共聚物中PNIPAM含量越大 ,水溶液体系的温度越高 ,形成胶束的临界胶束浓度 (CMC)越小 .特别值得指出的是 ,无论水溶液的温度是否高于PNIPAM接枝链段的相变温度 (LCST) ,即PNIPAM链段由亲水性转变为疏水性的温度 ,Dextran g PNIPAM均呈现一个临界胶束浓度大 ,对该现象给予了解释 .     

SEP嵌段共聚物胶束化过程的热力学

本文对苯乙烯/氢化异戊二烯(简称SEP)二嵌段共聚物在混合溶剂正辛烷-苯中的胶束化过程作了深入研究, 建立了用小角激光光散射法测定共聚物在有机溶剂中的临界胶束浓度(CMC)的方法.研究结果表明, 嵌段共聚物在有机溶剂中的胶束化过程与小分子的表面活性剂在水中的胶束化过程有着明显的不同, 前者是熵减和放热过程。     

双亲嵌段共聚物PSt-b-PAA在甲苯中的自聚集行为

以α-溴乙苯为引发剂,溴化亚铜为催化剂,2,2'-联吡啶为配体,用原子转移自由基聚合(ATRP)法合成了结构一定的嵌段共聚物聚苯乙烯-b-聚丙烯酸丁酯(PSt-b-PBA).经水解制备了双亲性嵌段共聚物聚苯乙烯-b-聚丙烯酸(PSt-b-PAA);采用单溶剂溶解法配制了PSt-b-PAA在甲苯中的反胶束溶液;以极性荧光化合物N-1-萘乙二胺盐酸盐(NEAH)为极性微区探针,用荧光光谱法并配合透射电镜观察探索了双亲嵌段共聚物PSt-b-PAA在甲苯溶液中的自聚集行为,考察了双亲性嵌段共聚物浓度、链结构及温度等因素对反胶束化行为的影响规律.结果表明,亲水链PAA短而亲油链PSt长的双亲嵌段共聚物PSt-b-PAA,用单溶剂溶解法可使其在甲苯中发生自聚集,形成以亲水段为核,疏水段为壳的星状反胶束结构;反胶束为10-20nm的球形聚集态结构;PSt-b-PAA的自聚集行为及临界胶束浓度与分子链的微结构和温度等因素相关,且随着共聚物浓度的增大,小胶束会逐渐结合形成大的纺垂状聚集体.     

Studies on the Effect of Organic Solvents and Temperature on the Micellar Solution of Pentamethylene-1,5-bis(tetradecyldimethylammonium bromide) Gemini Surfactant

Effects of three organic solvents, viz. methyl cellosolve, acetonitrile, and formamide, on the micellization process of Gemini surfactant pentamethylene-1,5-bis(tetradecyldimethylammonium bromide) aqueous solutions, with the volume percentages of the organic solvents up to 50%, have been investigated conductometrically. The studies were made at different temperatures and the data were used to find out different micellization parameters. From the study, it was observed that, although an increment in the amount of the organic solvents delays the micellization, the increase in the critical micelle concentration (cmc) is comparatively less below 20%(v/v) showing the predominance of water character in the bulk phase at lower compositions of the organic solvents. Applying equilibrium model for micelle formation, various thermodynamic parameters were also calculated from the temperature dependence of the cmc values and the results show that the micellization process becomes less spontaneous as the volume % of the organic solvent increases in the system due to the action of water-organic solvent mixed media as better solvent than pure water (solvophobic effect) for the studied Gemini molecules.     

Role of the solvophobic effect on micellization

Experimental data of amphiphiles aggregation phenomena in water-organic solvent mixtures were considered with the idea of investigating the role of the solvophobic effect on micellization. Changes in the critical micelle concentration, in the micellar ionization degree (for ionic surfactants) and in the aggregation number accompanying variations in the composition of the bulk phase of the micellar solutions were examined with the scope of understanding which properties of the water-organic solvent mixtures are important in the micellization process. Results point out that the cohesive energy density, measured either through the Hildebrand-Hansen solubility parameter or the Gordon parameter, seems to play an important role in determining the contribution of the solvophobic effect on the Gibbs energy of micellization in water-organic solvents mixtures.     

Micelle formation of a diblock copolymer having pyridine as pendant groups by carboxylic acids in nonselective solvents

The micelle formation of a poly(4-pyridinemethoxymethylstyrene)-block-polystyrene diblock copolymer (PPySt-b-PSt) was investigated in nonselective solvents using bifunctional and trifunctional carboxylic acids. The copolymer showed no self-assembly in 1,4-dioxane and tetrahydrofuran (THF) because the PPySt and PSt blocks were solvophilic to the solvents. Dynamic light scattering studies demonstrated that the copolymer formed micelles in the nonselective solvents in the presence of bifunctional carboxylic acids. Oxalic acid, maleic acid, citric acid, and phospholic acid promoted the micellization, while malonic acid, succinic acid, and glutalic acid had no effect on the micellization. The micellar size, aggregation number, and critical micelle concentration were dependent not only on the acid strength but also on the type of acid and the functionality. The micellization was also affected by the solvent quality. The micellization proceeded more effectively in 1,4-dioxane than in THF. It was found that the micellization occurred by hydrogen bonding between the pyridine moiety and the carboxylic acid and by the interaction among the carboxylic acids. This is because the copolymer needed over an equivalent of the acid to the PySt unit to complete the micellization. Furthermore, monofunctional carboxylic acid such as trichloroacetic acid and trifluoroacetic acid promoted the micellization, although dichloroacetic acid had no effect on the micellization.     

Thermodynamics and micellar properties of tetradecyltrimethylammonium bromide in formamide-water mixtures

The effect of formamide on the micellization of tetradecyltrimethylammonium bromide has been investigated by conductance and fluorescence probe experiments. The critical micelle concentration and the degree of counterion dissociation of micelles were obtained from conductance measurements in the temperature range of 20 to 40 degrees C. It was found that these two parameters increase with both temperature and formamide content in the solvent system. The thermodynamic parameters of micellization were estimated using the equilibrium model of micelle formation. The standard free energy of micellization was found to be negative in all cases and becomes less negative as the formamide content in the mixed solvent increases, but it is roughly independent of temperature. Although the entropic contribution was found to be larger than the enthalpy one, in particular at lower temperatures, an enthalpy-entropy compensation effect was observed for all systems. Micellar aggregation numbers were determined by the static quenching method, using pyrene as a probe and cetylpyridinium chloride as a quencher. The observed decrease in the micelle aggregation number, which is controlled by the increase in the surface area per headgroup, was attributed to an enhanced solvation in formamide rich solvent mixtures. Changes in the pyrene 1:3 ratio index, indicating a more polar environment, are consistent with an increased micellar solvation. Fluorescence polarization of both coumarin 6 and fluorescein are indicative of a decrease in microviscosity with cosolvent addition. The data on fluorescence anisotropy of coumarin 6 were analyzed using the wobbling in cone model. Data indicated the formation of micelles with a less ordered structure as the formamide increases in the solvent system.     

Micelle formation of a nonamphiphilic poly(vinylphenol)-<Emphasis Type="Italic">block</Emphasis>-polystyrene diblock copolymer in ethyl acetate

The micelle formation of a poly(vinylphenol)-block-polystyrene diblock copolymer was studied in ethyl acetate, a nonselective solvent using α,ω-diamine. The copolymer formed micelles in ethyl acetate in the presence of a small amount of the α,ω-diamine. Light scattering studies demonstrated that the micellization was dependent on the grade, the bulkiness, and the conformation of the diamines. The copolymer needed more diamine with the increasing grade of the diamine, due to a decrease in the basicity of the diamine. The bulkiness of the diamines also reduced the efficiency of the micellization by hindering the formation of the hydrogen bond cross-linking. Similarly, the conformation of the diamine affected the micellization, since the conformation determined the intramolecular spatial distance between the animo groups. Trans-1,2-cyclohexanediamine was more effective than the cis-isomer to produce the micelles. Furthermore, (1S,2S)-(+)-1,2-cyclohexanediamine, one of the mirror image isomers composing the trans-isomer, was more effective in producing the micelles than the trans-isomer. The interaction between the mirror image isomers also obstructed the micellization. The micellization, coupled with the thermoresponsivity of the micelles, were influenced by the solvent quality. The dissociation of the micelles into unimers was suppressed in ethyl acetate, while the reconstruction was promoted, in comparison with those in 1,4-dioxane and THF.     

Influence of Glycerol and Temperature on the Phase Behavior and Micellization of CTAB and SDS in Aqueous Solutions

In this work the micellization of sodium dodecylsulfate (SDS) and cetyltrimethyammonium bromide (CTAB) in water-glycerol mixed solvent have been investigated at 25, 35, and 45°C, respectively. The micellization of both surfactants in pure water at different temperatures has also been studied. The phase diagrams of the surfactants in water-glycerol mixed solvent were also established. From the conductivity measurements, the critical micelle concentration (CMC) and the degree of counterion dissociation (β) were obtained as a function of glycerol-water ratio and temperature. Standard free energy of micellization (ΔG°_mic) as a function of glycerol contents and temperature was calculated and discussed. It has been found that the micellization of the two surfactant in solutions with glycerol at 25°C and in pure water at higher temperatures are not the same although they have equal dielectric constants values.     

Formation of block copolymer micelles in solutions of a linear homopolymer in a good solvent

The existence of micelles of polystyrene-block-poly(ethylene/propene) in solutions of polystyrene in toluene was investigated. Toluene is a good solvent of both copolymer blocks whereas polystyrene and poly(ethylene/propene) are immiscible polymers. The presence of homopolystyrene at high enough concentration can induce the micellization of polystyrene-block-poly(ethylene/propene) in solution of a good solvent such as toluene. The thermodynamics of this new micelle system at a given polystyrene concentration was studied. Light scattering measurements were carried out in order to determine the critical micelle temperature (CMT) of different micellar solutions. Standard Gibbs energy, enthalpy and entropy of micellization were estimated from CMT and concentration data. The numerical values found were less negative than those found for micelle systems consisting in a block copolymer dissolved in a single selective solvent.     

Thermodynamic and aggregation properties of sodium dodecyl sulfate in aqueous binary mixtures of isomeric butanediols

The effect of aqueous binary mixtures of isomeric butanediols on the micellization of sodium dodecyl sulfate has been investigated. Conductivity and fluorescence techniques were employed to determine the critical micellar concentration, the degree of dissociation of the counterions and the aggregation numbers of the surfactants in these binary blends. Differential conductivity plots were employed to distinguish between the cooperative and the stepwise aggregation process of the surfactant in each solvent system. The mass-action model was employed to calculate the hydrophobic and the electrostatic contributions to the Gibbs energy of micellization as well as the monomer and the counterion concentrations in the postmicellar region. The thermodynamic parameters calculated for each system indicate that the micellization process occurs more readily in the presence of cosolvent owing to the formation of mixed micelles. Received: 5 July 2000 Accepted: 25 July 2000     

Temperature-triggered micellization of block copolymers on an ionic liquid surface

In situ neutron reflectivity was used to study thermally induced structural changes of the lamellae-forming polystyrene-block-poly(2-vinylpyridine) (PS-b-P2VP) block copolymer thin films floating on the surface of an ionic liquid (IL). The IL, 1-butyl-3-methylimidazolium trifluoromethanesulfonate, is a nonsolvent for PS and a temperature-tunable solvent for P2VP, and, as such, micellization can be induced at the air-IL interface by changing the temperature. Transmission electron microscopy and scanning force microscopy were used to investigate the resultant morphologies of the micellar films. It was found that highly ordered nanostructures consisting of spherical micelles with a PS core surrounded by a P2VP corona were produced. In addition, bilayer films of PS homopolymer on top of a PS-b-P2VP layer also underwent micellization with increasing temperature but the micellization was strongly dependent on the thickness of the PS and PS-b-P2VP layers.     

1,3-Butanediol as a co-solvent for the surfactant solutions

A biphasic solution containing water and precipitated phosphocholine (PC) is presented in order to investigate the consequences of 1,3-butanediol addition on the phase behavior of PC at different 1,3-butanediol concentrations and temperature values. With increasing the concentration of 1,3-butanediol in the mixed solvent at room temperature, the biphasic solution converts into turbid phase, two phase, and finally to a clear phase that is birefringent when viewed between two crossed polarizers. The birefringent phase moves to lower 1,3-butanediol contents at higher temperature values. The birefringent phase was observed via polarizing microscopy, and its rheological parameters were measured with cone plate method. In high 1,3-butanediol contents, solutions with 2.5% of PC behave as a gel with high yield stress value. The micellization of cetyltrimethyammonium bromide (CTAB) in a series of 1,3-butanediol/water mixed solvent at room temperature was also investigated. From the conductivity measurements, the critical micelle concentration and the degree of counterion dissociation of CTAB were obtained as a function of 1,3-butanediol. Standard free energy of micellization, as a function of 1,3-butanediol contents, was also estimated and discussed. Gibbs energies of micellization were found to have a good correlation with dielectric constant and Gordon parameters.