痕量双掺Sm~(3 )和Gd~(3 )对Y_2O_2S∶Eu~(3 )发光特性的影响

通过对Y2O2S∶Eu3 红色荧光粉痕量引入Sm3 和Gd3 的研究,发现可有效地增强发光强度,明显改善其电压特性(发射强度与激发电压间的关系特性),且不影响材料的其他物理化学性能。讨论和分析了发射强度增强、电压特性改善的原因:Gd3 对Y3 的置换,减少了因Eu3 对Y3 置换所引起的晶格的畸变、缺陷,使Eu3 离子晶场环境得到改善,从而减弱了无辐射过程及因晶格畸变所造成的能量损失;Sm3 的发射与Eu3 的吸收(激发)的部分重叠,且Eu3 激发光谱中包含有Sm3 激发跃迁谱线,导致了Sm3 →Eu3 共振能量传递可能性,有效地实现Sm3 对Eu3 的敏化效应。     

Gd3Ga5O12∶Eu3+发光纳米晶的燃烧合成及性质

以尿素为燃烧剂,乙二醇为分散剂采用燃烧法制备了Gd3Ga5O12∶Eu3+纳米晶。利用X射线衍射、电镜和荧光光谱对前驱体和热处理后样品的结构、形貌和发光性能进行了表征。XRD结果表明:700℃热处理2 h即可获得立方结构Gd3Ga5O12∶Eu3+纳米晶。根据Scherrer公式估算经700℃和900℃热处理2 h获得的纳米晶的一次性粒径分别为28 nm和42 nm。发射光谱和激发光谱的结果表明:特征发射峰来自于5D0-7FJ跃迁,而来自于Eu3+的5D0→7F1的磁偶极跃迁发射最强;宽激发带主要来自于Eu-O电荷迁移带和Gd3Ga5O12基质吸收。发射强度和激发强度随热处理温度的提高而增强。     

GdPO4:Eu3+和GdBO3:Eu3+中"Gd-Eu"间的能量传递

利用同步辐射光源(德国HASYLAB实验室的SUPERLUMI实验站)对高温固相法制备的GdPO4 Eu3+和GdBO3Eu3+的发射谱与激发谱进行了研究, 并从量子剪裁的角度对"Gd3+-Eu3+"之间的能量传递作了讨论. 在两种样品监测Eu3+红光发射的激发谱上, 都显著观察到了对应Gd3+离子4f-4f跃迁的谱线, 说明从基质中Gd3+离子向掺杂的Eu3+离子之间存在非常有效的能量传递, 这有利于量子剪裁的发生. 在激发谱上还观察到了对应Eu3+-O2-电荷迁移态的宽激发带(180～270 nm), 而对应Gd3+离子8S7/2→6GJ跃迁的谱线(196 nm, 203 nm)叠加在这个宽带之上, 微弱可辨, 这不利于Gd3+-Eu3+间交叉弛豫的能量传递过程, 从而不利于量子剪裁的发生. 结合Eu3+-O2-电荷迁移态位置变化的规律, 提出了如何避开其干扰以增强量子剪裁效应的材料设计方案.     

(Ca,Me)La4Si3O13:Eu3+(Me=Sr,Ba)荧光粉的结构和发光特性

采用高温固相法制备了(Ca,Me)La4Si3O13∶Eu3+(Me=Sr,Ba)系列红色荧光体,考察了Eu3+掺杂浓度和Sr2+,Ba2+置换对荧光体结构和发光特性的影响。Eu3+最佳掺杂浓度为nEu3+∶nLa3+=1∶7,5D0-7F2与5D0-7F1跃迁发射强度比为2.55。Eu3+掺杂使晶胞参数a和c呈线性变小,对c的影响大于a,使a/c比增大。Sr2+和Ba2+分别置换基质中的Ca2+可以形成完全固溶体,晶胞参数随Sr2+或Ba2+的置换量增加呈线性增大,使a/c比减小。各发射峰强度在Sr2+置换量为0.4 mol时出现极大值,但随Ba2+置换量的增加而不断增强,全置换后荧光强度最大。荧光体的色坐标为(0.638 5,0.353 0)。     

(Y,Gd)VO_4∶Eu~(3+)的紫外-真空紫外发光特性

用高温固相法合成了Y1-xGdxVO4∶Eu3 (0≤x≤1)系列单相样品并研究了其发光特性。在254nm激发下,观察到最大强度位于619nm的红色发射峰且其强度在Y/Gd=0.4/0.6时达到最大。在147nm激发下的发射峰与紫外下的一致,发射强度也是在Y/Gd=0.4/0.6时达到最大,大约是商用(Y,Gd)BO3∶Eu3 荧光体的65%。619nm监控下的真空紫外激发光谱由峰值位于158nm,204nm,247nm以及300nm的系列激发带组成,归属于钒酸根的基质吸收以及Gd3 、Y3 和Eu3 的电荷迁移带吸收。相对(Y,Gd)BO3∶Eu3 中Eu3 占据中心对称格位,(Y,Gd)VO4∶Eu3 中Eu3 占据非中心对称格位,其真空紫外下光谱色纯度更好。色坐标分别为(0.632,0.355),(0.672,0.328)。     

Gd2O3∶Eu3+纳米棒的制备与发光性能

在表面活性剂辅助的水热条件下合成出尺寸均一的Gd2O3∶Eu3+纳米棒, 对其结构和荧光性质进行了表征, 并对其生长机理进行了初步讨论. XRD结果表明, 水热前驱体样品为六方晶相的Gd(OH)3, 经过灼烧之后样品为立方相的Gd2O3. TEM照片表明, 所得样品为直径60 nm、长度约600 nm的纳米棒. 荧光光谱表明, 在波长为254 nm 的紫外光激发下, Gd2O3∶Eu3+纳米棒产生了不同于前驱体的特征红光发射, 对应于Eu3+ 的5D0-7F2跃迁, 表明Gd2O3是红色发光材料的良好基质.     

核壳型Gd2O3:Eu3+@Y2O3纳米发光材料的制备与发光性能

采用均相沉淀法制备了均匀球形的Gd2O3:Eu3+@Y2O3核壳结构纳米发光材料.XRD结果表明经过800℃焙烧后样品为立方晶系的Gd2O3,并且晶体发育良好,包覆Y2O3之后Gd2O3的衍射峰位置无明显变化,但随着包覆厚度的增加,出现了立方晶系Y2O3的衍射峰.FTIR谱图观测到了Gd-O,Y-O伸缩振动吸收峰,随着包覆厚度的减少吸收峰增强,认为当包覆层的厚度适当时,颗粒表面的悬空键(断键)变少,Gd(Eu,Y)-O键增多所致.SEM表明包覆前后样品为均匀分散的球形结构.XPS分析进一步证明了表面包覆上了Y2O3.荧光光谱表明:纳米Gd2O3:Eu3+表面包覆不同厚度的基质Y2O3后,均观测到Eu3+离子的特征红光发射,当包覆厚度R=4:1时的发光强度比未包覆的Gd2O3:Eu3+增强,认为核-壳型样品降低了纳米Gd2O3:Eu3+的表面效应给发光强度带来的负面影响.     

BaLiF3∶Eu,Gd中Gd3+→Eu2+的能量传递

研究了BaLiF3中Gd3+和Eu2+的光谱性质及Gd3+对Eu2+的能量传递过程,讨论了传递机理.Gd3+的含量(物质的量分数)为0.3%时,传递效率最高,传递几率PSA＝1.35×105 s-1.当Gd3+的含量高于0.3%时,由于Gd3+和Eu2+竞争吸收Gd3+占优势,增加Gd3+含量,竞争吸收比相应增加,Eu2+自身吸收光子数目减少,发射强度降低.     

Y2O3:Eu3+纳米线阵列的制备与表征

Y2O3:Eu3+红色荧光粉由于色纯度高、化学性质稳定和量子效率接近100%而广泛用于荧光灯和投影电视等方面.近年来,Y2O3:Eu3+的大量研究工作主要集中于纳米粉末的制备方法及其与体相材料不同的发光特性[1～3].最近,有关Y2O3:Eu3+及其稀土化合物的纳米管、纳米线和纳米带一维材料的制备成为研究热点.Wu Changfeng等[4,5]利用表面活性剂合成了Y2O3 : Eu3+纳米管.激光格位选择激发测试结果表明,Eu3+在纳米管中占据3个不同的格位,其611 nm处的红色发光峰出现了宽化.He Yu等[6]采用水热法及退火处理制备出了Y2O3:Eu3+纳米带,发现Eu3+的发射峰不仅宽化,而且出现了625 nm的新峰.Li Yadong等[7～9]采用水热法制备了稀土氧化物、硫氧化物和氢氧化物等的纳米线和纳米管,并探索了其形成机理,同时发现Y2O3S : yb3+,Er3+具有上转换的性质.     

白光LED用Sr_(0.955)Al_2Si_(2-x)Ti_xO_8∶Eu~(2+)荧光粉的晶体结构和光谱特性

由高温固相反应制得Sr0.955Al2Si2-xTixO8∶Eu2+(x=0~1.0)系列试样,研究了Ti4+置换Si4+对其晶体结构和光谱特性的影响。Ti4+以类质同相替代Si4+进入基质晶格中,形成了连续固溶体,其晶胞参数a,b,c,β和晶胞体积V随Ti4+置换量呈线性递增。Ti4+置换Si4+对晶胞参数c的影响显著,b其次,a最小。荧光激发谱为宽带,位于230~400nm,由267nm、305nm、350nm和375nm4个峰拟合成,表观峰值位于351nm;随着Ti4+置换量的增加,半高宽(FWHM)从105nm减小到93nm。发射光谱位于380~600nm,表观峰值位于407nm,可由406nm和441nm两峰拟合而成并且随Ti4+置换量增加线性红移,Ti4+进入晶格对长波长发射中心影响较少;Ti4+置换量为1.0时,表观发射峰位从407nm红移至417nm;利用试样荧光光谱和VanUitert经验公式,得出SrAl2Si2O8∶Eu2+中Sr2+的配位数为9。随着Ti4+置换量Si4+进入基质晶格,造成Eu-O距离变小,使得Eu2+所处的晶体场强度增强,发光中心Eu2+的5d能级分裂增大,造成Eu2+最低发射能级重心下移,两拟合谱峰峰位均呈线性红移。     

Phosphine-catalyzed annulations of azomethine imines: allene-dependent [3 + 2], [3 + 3], [4 + 3], and [3 + 2 + 3] pathways

In this paper we describe the phosphine-catalyzed [3 + 2], [3 + 3], [4 + 3], and [3 + 2 + 3] annulations of azomethine imines and allenoates. These processes mark the first use of azomethine imines in nucleophilic phosphine catalysis, producing dinitrogen-fused heterocycles, including tetrahydropyrazolo-pyrazolones, -pyridazinones, -diazepinones, and -diazocinones. Counting the two different reaction modes in the [3 + 3] cyclizations, there are five distinct reaction pathways-the choice of which depends on the structure and chemical properties of the allenoate. All reactions are operationally simple and proceed smoothly under mild reaction conditions, affording a broad range of 1,2-dinitrogen-containing heterocycles in moderate to excellent yields. A zwitterionic intermediate formed from a phosphine and two molecules of ethyl 2,3-butadienoate acted as a 1,5-dipole in the annulations of azomethine imines, leading to the [3 + 2 + 3] tetrahydropyrazolo-diazocinone products. The incorporation of two molecules of an allenoate into an eight-membered-ring product represents a new application of this versatile class of molecules in nucleophilic phosphine catalysis. The salient features of this protocol--the facile access to a diverse range of nitrogen-containing heterocycles and the simple preparation of azomethine imine substrates--suggest that it might find extensive applications in heterocycle synthesis.     

Reciprocal system 3Tl2S + Bi2Se3 ↔ 3Tl2Se + Bi2S3

The reciprocal system 3Tl₂S + Bi₂Se₃ ? 3Tl₂Se + Bi₂S₃ has been investigated by DTA, X-ray powder diffraction analysis, and emf measurements. Some polythermal sections and the isothermal section at 500 K of the phase diagram and the projection of the liquidus surface of this system have been constructed, and the types and coordinates of the invariant and univariant equilibria have been determined. The existence of wide regions of quaternary solid solutions based on the binary compounds Tl₂S, Tl₂Se, Bi₂S₃, and Bi₂Se₃, and solid solutions between the temary compounds TlBiS₂ and TlBiSe₂ have been established.     

Secondary kinetics of methanol decomposition: theoretical rate coefficients for 3CH2 + OH, 3CH2 + 3CH2, and 3CH2 + CH3

Direct variable reaction coordinate transition state theory (VRC-TST) rate coefficients are reported for the (3)CH(2) + OH, (3)CH(2) + (3)CH(2), and (3)CH(2) + CH(3) barrierless association reactions. The predicted rate coefficient for the (3)CH(2) + OH reaction (approximately 1.2 x 10(-10) cm(3) molecule(-1) s(-1) for 300-2500 K) is 4-5 times larger than previous estimates, indicating that this reaction may be an important sink for OH in many combustion systems. The predicted rate coefficients for the (3)CH(2) + CH(3) and (3)CH(2) + (3)CH(2) reactions are found to be in good agreement with the range of available experimental measurements. Product branching in the self-reaction of methylene is discussed, and the C(2)H(2) + 2H and C(2)H(2) + H2 products are predicted in a ratio of 4:1. The effect of the present set of rate coefficients on modeling the secondary kinetics of methanol decomposition is briefly considered. Finally, the present set of rate coefficients, along with previous VRC-TST determinations of the rate coefficients for the self-reactions of CH(3) and OH and for the CH(3) + OH reaction, are used to test the geometric mean rule for the CH(3), (3)CH(2), and OH fragments. The geometric mean rule is found to predict the cross-combination rate coefficients for the (3)CH(2) + OH and (3)CH(2) + CH(3) reactions to better than 20%, with a larger (up to 50%) error for the CH(3) + OH reaction.     

Eu^2＋在BaF2—xYF3体系中的光谱性质及其对Tb3＋的能量传递

研究了钡钇复合氟化物体系中Ｅｕ＾２＋的光谱性质和变化规律，讨论了影响Ｅｕ＾２＋光谱的因素，特别是氧的存在对Ｅｕ＾２＋激发和发射能量的影响，发现在ＢａＹＦ５基质中Ｅｕ＾２＋对Ｔｂ＾３＋的有效参量传递。     

多孔二氧化硅中Gd3+ → Eu3+的能量传递

通过水热反应法，获得了单掺和双掺Eu³⁺，Gd³⁺的多孔二氧化硅组装体，研究了掺杂体系的光谱特性，观察到Gd³⁺ → Eu³⁺的能量传递。分析了能量传递过程，探讨了在多孔二氧化硅中Gd³⁺→Eu³⁺的能量传递的机理，其机理主要为电偶极-电偶极相互作用。     

Bi3+-Er3+ and Bi3+-Yb3+ Codoped Cs2AgInCl6 Double Perovskite Near-Infrared Emitters

Bi³⁺ and lanthanide ions have been codoped in metal oxides as optical sensitizers and emitters. But such codoping is not known in typical semiconductors such as Si, GaAs, and CdSe. Metal halide perovskite with coordination number 6 provides an opportunity to codope Bi³⁺ and lanthanide ions. Codoping of Bi³⁺ and Ln³⁺ (Ln=Er and Yb) in Cs₂AgInCl₆ double perovskite is presented. Bi³⁺-Er³⁺ codoped Cs₂AgInCl₆ shows Er³⁺ f-electron emission at 1540 nm (suitable for low-loss optical communication). Bi³⁺ codoping decreases the excitation (absorption) energy, such that the samples can be excited with ca. 370 nm light. At that excitation, Bi³⁺-Er³⁺ codoped Cs₂AgInCl₆ shows ca. 45 times higher emission intensity compared to the Er³⁺ doped Cs₂AgInCl₆. Similar results are also observed in Bi³⁺-Yb³⁺ codoped sample emitting at 994 nm. A combination of temperature-dependent (5.7 K to 423 K) photoluminescence and calculations is used to understand the optical sensitization and emission processes.     

Ca2+、La3+及Eu3+对NaDC胶团的作用

在水溶液中将脱氧胆酸钠（ＮａＤＣ）分别与ＣａＣＬ２、ＥｕＣｌ３及ＬａＣｌ３反应,改变反应物浓度和配比,合成了系列脱氧胆酸络全物。利用红外光谱（ＦＴＩＲ）、元素分析、ＩＣＰ分析及Ｘ身材线粉末衍射谱,对它们的组成和结构进行了研究。结果表明：水溶液中ＣａＣｌ２与ＮａＤＣ的反应不是简单离子间的反应,改变其反应物浓度和配比,生成组成和结构不同的络合物;而ＬｎＣｌ３与ＮａＤＣ反应时,反应物浓度和配比的改变不影