Comparison of photocatalytic performance of anatase TiO2 prepared by low and high temperature route

Anatase TiO₂ was prepared by a facile sol-gel method at low temperature through tailoring the pH of sol-gel without calcination. As a control, anatase TiO₂ was also synthesized by the conventional sol-gel process, in which calcination at 500 °C was required to transform the amorphous oxide into highly crystalline anatase. As-prepared samples were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL). Their photocatalytic activities were evaluated by degradation of methyl orange under UV light irradiation. On the basis of experiment results, it could be concluded that TiO₂ prepared by low temperature route showed more advantages in small particle size, highly dispersion nature, abundance of surface hydroxyl groups, strong PL signal, and high photocatalytic activity over TiO₂ obtained by the conventional sol-gel process. Furthermore, the reason of the former possessing higher photocatalytic activity was discussed.     

Enhanced photocatalytic activity of TiO2 nano-structured thin film with a silver hierarchical configuration

TiO₂ sol-gels with various Ag/TiO₂ molar ratios from 0 to 0.9% were used to fabricate silver-modified nano-structured TiO₂ thin films using a layer-by-layer dip-coating (LLDC) technique. This technique allows obtaining TiO₂ nano-structured thin films with a silver hierarchical configuration. The coating of pure TiO₂ sol-gel and Ag-modified sol-gel was marked as T and A, respectively. According to the coating order and the nature of the TiO₂ sol-gel, four types of the TiO₂ thin films were constructed, and marked as AT (bottom layer was Ag modified, surface layer was pure TiO₂), TA (bottom layer was pure TiO₂, surface layer was Ag modified), TT (pure TiO₂ thin film) and AA (TiO₂ thin film was uniformly Ag modified). These thin films were characterized by means of linear sweep voltammetry (LSV), X-ray diffraction (XRD), scanning electron microscopy (SEM), electrochemical impedance spectroscopy and transient photocurrent (I_ph). LSV confirmed the existence of Ag⁰ state in the TiO₂ thin film. SEM and XRD experiments indicated that the sizes of the TiO₂ nanoparticles of the resulting films were in the order of TT > AT > TA > AA, suggesting the gradient Ag distribution in the films. The SEM and XRD results also confirmed that Ag had an inhibition effect on the size growth of anatase nanoparticles. Photocatalytic activities of the resulting thin films were also evaluated in the photocatalytic degradation process of methyl orange. The preliminary results demonstrated the sequence of the photocatalytic activity of the resulting films was AT > TA > AA > TT. This suggested that the silver hierarchical configuration can be used to improve the photocatalytic activity of TiO₂ thin film.     

Effect of surface species on Cu-TiO2 photocatalytic activity

The Cu-TiO₂ nanoparticles with different Cu dopant content were prepared by sol-gel method. The structure of the as-prepared catalysts and the surface species of Cu-TiO₂ were determined using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and diffuse reflection spectroscopy (DRS). The relationship between the photocatalytic activity and the surface species of Cu-TiO₂ was revealed via the measurement of surface photovoltage spectroscopy (SPS) as well as the degradation of the rhodamine B (RhB). The experimental results suggest that the Cu-TiO₂ photocatalysts with appropriate content of Cu (about 0.06 mol%) possess abundant electronic trap, which effectively inhibits the recombination of photoinduced charge carriers, improving the photocatalytic activity of TiO₂. While at high Cu dopant region (>0.06 mol%), the excessive oxygen vacancies and Cu species can become the recombination centers of photoinduced electrons and holes. Meanwhile, at heavy Cu doping concentration, excessive P-type Cu₂O can cover the surface of TiO₂, which leads to decrease in the photocatalytic activity of photocatalyst. The photocatalytic experimental results are in good agreement with the conclusions of SPS measurements, indicating that there is a close relationship between the photocatalytic activity and the intensity of SPS spectra.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

Preparation and photo-induced superhydrophilicity of composite TiO2-SiO2-In2O3 thin film

In this work, TiO₂-SiO₂-In₂O₃ composite thin films on glass substrates were prepared by the sol-gel dip coating process. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structural and chemical properties of the films. UV-vis spectrophotometer was used to measure the transmittance spectra of thin films. The water contact angle (WCA) of thin films during UV/vis irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that fabrication of composite film has a significant effect on transmittance and superhydrophilicity of TiO₂ films.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

Effects of surface-modification with Bi2O3 on the thermal stability and photoinduced charge property of nanocrystalline anatase TiO2 and its enhanced photocatalytic activity

Bi₂O₃ surface-modified TiO₂ nanoparticle has been synthesized by sol-hydrothermal processes, followed by post-treatment with an appropriate amount of bismuth nitrate solution, and also characterized by XRD, Raman, BET, TEM, FT-IR, XPS, UV-vis DRS and SPS techniques. The effects of the surface-modification with Bi₂O₃ on the thermal stability, photoinduced charge separation and photocatalytic activity for degrading rhodamine B (or phenol) under ultraviolet (or visible) irradiation are investigated in detail, along with their relationships and the activity enhancement mechanisms are also suggested. The results show that the modification with Bi₂O₃ can improve the thermal stability of the as-prepared anatase crystallites, consequently enhancing the anatase crystallinity so as to promote the photoinduced charge separation. And the modification with Bi₂O₃ also extends the optical response range. It can be concluded that the activity enhancement of surface-modified TiO₂ is mainly attributed to the increase in the photoinduced charge separation rate and to the extent of the optical response range, compared with un-modified ones. Moreover, the inhibition phase transformation mechanism related to Bi₂O₃ is suggested.     

Structural study of sol-gel Au/TiO2 films from nanopowders

TiO₂ represents one of the most important sol-gel materials, due to its photocatalytic properties, in the case of both powders and coatings. Nanostructured titania has been reported to be used in many applications in different fields ranging from optics to gas sensor via solar energy. Recent researches point out the existence of new procedures used in order to enhance the efficiency of the photocatalytic process. The metal ion doping is such an example. Two types of 2 wt.% Au containing TiO₂ powders have been embedded in sol-gel vitreous TiO₂ matrices. Au-doped TiO₂ films have been prepared from these sols, by dipping procedure using quartz microscopic slides, as substrates. The relationship between the synthesis conditions and the properties of titania nanosized materials, such as thermal stability, phase composition, crystallinity, and the influence of dopant was investigated. The hydrophilic properties of the films were correlated with their structure, composition and surface morphology.     

Enhancement of the photocatalytic activity of TiO2 nanoparticles by surface-capping DBS groups

TiO₂ nanoparticles capped with sodium dodecylbenzenesulfonate (DBS) are synthesized by a sol-hydrothermal process using tetrabutyl titanate and DBS as raw materials. The effects of surface-capping DBS on the surface photovoltage spectroscopy (SPS), photoluminescence (PL) and photocatalytic performance of TiO₂ nanoparticles are principally investigated together with their relationships. The results show that the surface of TiO₂ nanoparticles can be well capped by DBS groups while the pH value and added DBS amount are controlled at 5.0 and 2% of TiO₂ mass weight, respectively, and the linkage between DBS groups and TiO₂ surfaces is mainly by means of quasi-sulphonate bond. The intensities of SPS and PL spectra of TiO₂ obviously decrease after DBS-capping, while the activity can greatly increase during the photocatalytic degradation of Rhodamine B (RhB) solution, which are mainly attributed to the electron-withdrawing character of the DBS groups. Moreover, the enhancement of photocatalytic activity of DBS-capped TiO₂ is also related to the increase in the capability for adsorbing RhB.     

Preparation of nanocrystalline Sn-TiO2−X via a rapid and simple stannous chemical reducing route

The Sn-TiO_2−X nanoparticles have been prepared via a rapid and simple stannous chemical reducing method. The as-prepared Sn-TiO_2−X nanoparticles were investigated by means of surface photovoltage spectroscopy (SPS), XPS, and DRS technology as well as photocatalytic degradation of RhB were studied under illumination. The experiment results revealed that the reduction of the TiO₂ particles raised their Fermi level, which can enhance the driven force of photoinduced electrons transferring from TiO₂ to adsorbed O₂ and SnO₂ on the surface of TiO₂. On the other hand, the amount of oxygen vacancies of the Sn-TiO_2−X increased after the stannous chemical reduction. The oxygen vacancies can also effectively inhibit the recombination of photoinduced electrons and holes pairs. These factors are favorable to the photocatalytic reaction.     

Oblique angle deposition of TiO2 thin films prepared by electron-beam evaporation

Optical, structural and photocatalytic properties of TiO₂ thin films obliquely deposited on quartz glass substrate using an electron-beam evaporation method were investigated. The photocatalytic activity of the films was evaluated by photodecomposition of methylene blue. An increase in incident deposition angle increased the porosity and surface roughness of the TiO₂ films. As a result, the photocatalytic activity was enhanced with incident deposition angle up to 60°. However, a further increase in incident deposition angle to 75° reduced the photocatalytic activity due to a lack of the crystalline phase.     

Photocatalytic properties of nanocrystalline TiO<Subscript>2</Subscript> thin films doped with Tb

In this work photocatalytic properties of TiO₂ thin films doped with different amount of Tb have been described. Thin films were prepared by high energy reactive magnetron sputtering process. Comparable photocatalytic activity has been found for all doped TiO₂ thin films, while different amounts of Tb dopant (0.4 and 2.6 at. %) results in either an anatase or rutile structure. It was found that the terbium dopant incorporated into TiO₂ was also responsible for the amount of hydroxyl groups and water particles adsorbed on the thin film surfaces and thus photocatalytic activity was few times higher in comparison with results collected for undoped TiO₂ thin films.     

Effect of surface fluorination on the photocatalytic and photo-induced hydrophilic properties of porous TiO2 films

Porous surface-fluorinated TiO₂ (F-TiO₂) films were prepared through PEG modified sol-gel method and surface fluorination. The as-prepared films were characterized with XRD, FTIR, AFM, XPS and UV-vis DRS. The effects of surface fluorination on the photocatalytic activity and hydrophilicity of porous TiO₂ film were studied by photocatalytic degradation of rhodamine B (RhB) as well as water contact angle (CA) on porous TiO₂ film. The results showed that the surface fluorination increased the adsorption of RhB on the porous TiO₂ film and enhanced the photocatalytic degradation of RhB. The concentration and pH of NaF solutions affected much the photocatalytic activity of porous TiO₂ film. Porous F-TiO₂ film prepared in 40 mM NaF solution at pH 4.0 showed the highest photocatalytic activity. Because of its porous structure, the porous F-TiO₂ film had original water CA of 22.7°, which is much smaller than that of normal F-TiO₂ film. Under UV light irradiation, the water CA of porous F-TiO₂ film decreased to 5.1° in 90 min.     

Preparation and photocatalytic activity of CeO2/TiO2 interface composite film

The CeO₂/TiO₂ and TiO₂/CeO₂ interface composite films were prepared on glass substrates by the sol-gel process via dip-coating and calcining technique. The scanning electron microscopy (SEM) revealed that the TiO₂ layer has a compact and uniformity glasslike surface with 200 nm in thickness, and the CeO₂ layer has a coarse surface with 240 nm in thickness. The X-ray diffractometer (XRD) analysis showed that the TiO₂ layer is made up of anatase phase, and the CeO₂ layer is structured by cubic fluorite phase. Through a series of photo-degradation experiments, the relationship of the photocatalytic activity with the constituents of the films was studied. In virtue of the efficient interfacial charge separation via the process of electron transfer from TiO₂ to CeO₂, the photocatalytic activity of the CeO₂/TiO₂ composite film is high. Contrarily, the photocatalytic activity of the TiO₂/CeO₂ composite film is low, due to its inert surface made up of CeO₂ with broad bandwidth. Apart from the effect of the film structure, the effect of film thickness on photocatalytic activity was also discussed.     

Effects of microwave drying on the microstructure and photocatalytic activity of bimodal mesoporous TiO2 powders

Bimodal nanocrystalline mesoporous TiO₂ powders with highly photocatalytic activity were prepared by a hydrothermal method using tetrabutylorthotitanate as precursor, and then dried in microwave oven. The prepared samples were characterized by XRD, SEM, TEM, HRTEM and N₂ adsorption-desorption measurement. The photocatalytic activity was evaluated by the photocatalytic degradation of acetone in air under UV light irradiation at room temperature. The effects of microwave drying on the microstructures and photocatalytic activity of the TiO₂ powders were investigated and discussed. The results show that microwave drying not only promotes the growth of the pores but also greatly reduces the state of agglomeration within the powders. All the microwave-dried TiO₂ powders show higher photocatalytic activity than Degussa P-25 (P25) and the TiO₂ powders dried by conventional method.     

Microemulsion synthesis, characterization of bismuth oxyiodine/titanium dioxide hybrid nanoparticles with outstanding photocatalytic performance under visible light irradiation

Reverse microemulsions, consisting of n-hexanol, Triton X-100, Cyclohexane and aqueous salt solutions, were used to synthesize BiOI, TiO₂ and BiOI/TiO₂ hybrid nanoparticles at room temperature. The particles had been characterized by X-ray powder diffraction, FT-IR spectra, TG-DSC analysis, nitrogen sorption, electron microscopy, and UV-vis diffuse reflectance spectroscopy. The photocatalytic properties of those particles were evaluated by degradation of methyl orange under visible light irradiation. The BiOI/TiO₂ composites showed about 5 times higher photocatalytic performances than BiOI when the mole ratio of BiOI to TiO₂ was 75%. The remarkable enhancement in the visible light photocatalytic activities of the BiOI/TiO₂ heterostructures could be first attributed to the effective electron-hole separations at the interfaces of the two semiconductors, which facilitated the transfer of the photoinduced carriers. Meanwhile, the heterojunction formed between BiOI and TiO₂ would further retard the recombination of photoinduced carriers. In addition, high degree of crystallization, bimodal porous structure, relative large specific surface area, and appropriate energy band gap have great contribution to the enhancement of photocatalytic performance.     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Preparation of TiO2 thin films from autoclaved sol containing needle-like anatase crystals

A new inorganic sol-gel method was introduced in this paper to prepare TiO₂ thin films. The autoclaved sol with needle-like anatase crystals was synthesized using titanyl sulfate (TiOSO₄) and peroxide (H₂O₂) as starting materials. The transparent anatase TiO₂ thin films were prepared on glass slides from the autoclaved sol by sol-gel dip-coating method. A wide range of techniques such as Fourier transform infrared transmission spectra (FT-IR), X-ray diffraction (XRD), thermogravimetry-differential thermal analysis (TG-DTA), scanning electron microscopes, X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible spectrum were applied to characterize the autoclaved sol and TiO₂ thin films. The results indicate that the autoclaved sol is flavescent, semitransparent and stable at room temperature. The anatase crystals of TiO₂ films connect together to form net-like structure after calcined and the films become uniform with increasing heating temperature. The surface of the TiO₂ films contain not only Ti and O elements, but also a small amount of N and Na elements diffused from substrates during heat treatment. The TiO₂ films are transparent and their maximal light transmittances exceed 80% under visible light region.     

Deposition of graded TiO2 films featured both hydrophobic and photo-induced hydrophilic properties

Graded TiO₂ films were deposited on unheated glass substrates by using a twin dc magnetron sputtering system. The graded TiO₂ films showed a highly polycrystalline structure of anatase with a little rutile phases revealed by X-ray diffraction spectra. The surface energy of the fresh and UV irradiated films were evaluated by water contact angle measurement. The results indicated that the water contact angle of the fresh graded TiO₂ films was found within 100-112°. The films then became a highly hydrophilic surface with the water contact angle of almost zero under 60 min UV irradiation. The XPS spectrum of Ti 2p revealed that the graded TiO₂ films became a stoichiometric titanium oxide layer near the surface, proving that titanium was fully oxidized. It was found that the surface OH group density depended on the substrates employed for given sputtering conditions. In addition, AFM images revealed a considerably rough surface of the graded films with RMS roughness of 12.6-14.5 nm. One can conclude that the unique properties of highly hydrophobicity and photo-induced hydrophilicity can be attributed to fully oxidized chemical composition and higher roughness on the film surface.     

Deactivation of TiO2 photocatalytic films loaded on aluminium: XPS and AFM analyses

TiO₂ films were loaded on aluminium substrates by dip-coating method. Based on cyclic photocatalytic degradation experiments using benzamide as model molecule, XPS and AFM tests, the deactivating behaviour of the samples was studied. Experiment results show that the samples with less coating times (one to four times) deactivated very quickly, while the samples coated more than five times did not lose activity. Al element was proved to segregate from substrate and diffuse into TiO₂ films during calcination and annealing treatment, existing as mixture of Al₂O₃ and Al(OH)₃ at the boundaries among TiO₂ particles. During photocatalytic reactions in aqueous phase, the transformation of Al from Al₂O₃ to Al(OH)₃ and the leaching of the latter brought out serious alternation of surface morphology to the samples coated one to three times, on whose surface Ti³⁺ and Ti²⁺ centers were also detected after six cycles of photocatalytic reactions, while fresh films and the tested films which did not deactivate possess unique +4 valence Ti. The alteration of surface morphology, together with the change of valence of surface Ti element, resulted in the deactivation encountered in this research.