A Novel Sensor Based on Manganese azo‐Macrocycle/Carbon Nanotubes to Perform the Oxidation and Reduction Processes of Two Diphenol Isomers

The present work describes the development of a selective and sensitive voltammetric sensor for simultaneous determination of catechol (CC) and hydroquinone (HQ), based on a glassy carbon (GC) electrode modified with manganese phthalocyanine azo‐macrocycle (MnPc) adsorbed on multiwalled carbon nanotubes (MWCNT). Scanning electron microscopy and scanning electrochemical microscopy were used to characterize the composite material (MnPc/MWCNT) on the glassy carbon electrode surface. The modified electrode showed excellent electrochemical activity towards the simultaneous oxidation and reduction of CC and HQ. On the MnPc/MWCNT/GC electrode, both CC and HQ can generate a pair of quasi‐reversible and well‐defined redox peaks. Under optimized experimental and operational conditions, the cathodic peak currents were linear over the range 1–600 µmol L^?1 for both CC and HQ, with limits of detection of 0.095 and 0.041 µmol L^?1, respectively. The anodic peak currents were also linear over the range 1–600 µmol L^?1 for both CC and HQ, with limits of detection of 0.096 and 0.048 µmol L^?1, respectively. The proposed method was effectively applied for the simultaneous detection of hydroquinone and catechol in water samples and the results were in agreement with those obtained by a comparative method described in the literature.     

Carbon Nanotube Based Sensor for Simultaneous Determination of Acetaminophen and Ascorbic Acid Exploiting Multiple Response Optimization and Measures in the Presence of Surfactant

A simple procedure for the simultaneous determination of acetaminophen (AC) and ascorbic acid (AA) by differential pulse voltammetry (DPV) using a carbon nanotube paste electrode exploiting measures in cetylpyridinium bromide (CPB) medium is described. Under the best instrumental parameters of DPV, optimized by means of factorial design, the calibration plots in the range 100.0–700.0 µmol L^?1 (r=0.993) and 39.4–146.3 µmol L^?1 (r=0.995) with limits of detection of 7.1 and 2.1 µmol L^?1, were achieved for AA and AC, respectively. The developed method was successfully applied for the AC and AA determination in pharmaceutical formulations, whose accuracy was attested by comparison with HPLC method.     

A Voltammetric Sensor Based on Modified Multiwall Carbon Nanotubes for Cysteamine Determination in the Presence of Tryptophan Using p‐Aminophenol as a Mediator

Determination of cysteamine and tryptophan is described by electrochemical methods using p‐aminophenol‐multiwall carbon nanotubes paste electrode. Cysteamine and tryptophan in mixture can each be measured independently from each other with a potential difference of 600 mV. The results showed that the electrocatalytic currents increased linearly with cysteamine and tryptophan concentrations over the ranges 0.5–300 µmol L^?1 and 10.0–650 µmol L^?1, respectively. The detection limits for cysteamine and tryptophan are found to be 0.14 and 5.9 µmol L^?1, respectively. The proposed method is successfully employed for the determination of cysteamine in both capsule and urine samples.     

Voltammetric Determination of 4‐Nitrophenol and 5‐Nitrobenzimidazole Using Different Types of Silver Solid Amalgam Electrodes – A Comparative Study

The voltammetric behavior of two genotoxic nitro compounds (4‐nitrophenol and 5‐nitrobenzimidazole) has been investigated using direct current voltammetry (DCV) and differential pulse voltammetry (DPV) at a polished silver solid amalgam electrode (p‐AgSAE), a mercury meniscus modified silver solid amalgam electrode (m‐AgSAE), and a mercury film modified silver solid amalgam electrode (MF‐AgSAE). The optimum conditions have been evaluated for their determination in Britton‐Robinson buffer solutions. The limit of quantification (L_Q) for 5‐nitrobenzimidazole at p‐AgSAE was 0.77 µmol L^?1 (DCV) and 0.47 µmol L^?1 (DPV), at m‐AgSAE it was 0.32 µmol L^?1 (DCV) and 0.16 µmol L^?1 (DPV), and at MF‐AgSAE it was 0.97 µmol L^?1 (DCV) and 0.70 µmol L^?1 (DPV). For 4‐nitrophenol at p‐AgSAE, L_Q was 0.37 µmol L^?1 (DCV) and 0.32 µmol L^?1 (DPV), at m‐AgSAE it was 0.14 µmol L^?1 (DCV) and 0.1 µmol L^?1 (DPV), and at MF‐AgSAE, it was 0.87 µmol L^?1 (DCV) and 0.37 µmol L^?1 (DPV). Thorough comparative studies have shown that m‐AgSAE is the best sensor for voltammetric determination of the two model genotoxic compounds because it gives the lowest L_Q, is easier to prepare, and its surface can be easily renewed both chemically (by new amalgamation) and/or electrochemically (by imposition of cleaning pulses). The practical applicability of the newly developed methods was verified on model samples of drinking water.     

N‐(3,4‐Dihydroxyphenethyl)‐3,5‐dinitrobenzamide‐Modified Multiwall Carbon Nanotubes Paste Electrode as a Novel Sensor for Simultaneous Determination of Penicillamine,Uric acid,and Tryptophan

N‐(3,4‐dihydroxyphenethyl)‐3,5‐dinitrobenzamide modified multiwall carbon nanotubes paste electrode was used as a voltammetric sensor for oxidation of penicillamine (PA), uric acid (UA) and tryptophan (TP). In a mixture of PA, UA and TP, those voltammograms were well separated from each other with potential differences of 300, 610, and 310 mV, respectively. The peak currents were linearly dependent on PA, UA and TP concentrations in the range of 0.05–300, 5–420, and 1.0–400 µmol L^?1, with detection limits of 0.021, 2.0, and 0.82 µmol L^?1, respectively. The modified electrode was used for the determination of those compounds in real samples.     

Electrocatalytic and Simultaneous Determination of Ascorbic Acid,Nicotinamide Adenine Dinucleotide and Folic Acid at Ruthenium(II) Complex‐ZnO/CNTs Nanocomposite Modified Carbon Paste Electrode

This paper describes the development a novel ruthenium(II) complex‐ZnO/CNTs modified carbon paste electrode (Ru(II)/ZnO/CNTs/CPE) for the electrocatalytic determination of ascorbic acid (AA). The objective of this novel electrode modification was to seek new electrochemical performances for the detection of AA, nicotinamide adenine dinucleotide (NADH) and folic acid (FA). The peak potentials recorded were 170, 500 and 830 mV vs. Ag/AgCl/KCl_sat for AA, NADH and FA, respectively. The peak currents were linearly dependent on AA, NADH and FA concentrations using square wave voltammetry (SWV) method at the ranges of 0.008–251, 1.0–650, and 3.0–700 µmol L^?1, with detection limits of 0.005, 0.5, and 1.0 µmol L^?1, respectively.     

Flow‐Injection Pulsed‐Amperometric Determination of Free Glycerol in Biodiesel at a Gold Electrode

This work reports the highly‐sensitive amperometric determination of free glycerol in biodiesel at a gold electrode adapted in a flow‐injection analysis (FIA) cell. The amperometric method involved the continuous application of three sequential pulses to the working electrode (+250 mV, +700 mV, and ?200 mV, for 100 ms each). This sequence of potential pulses eliminated electrode passivation and dramatically increased the analytical signal. The proposed FIA‐amperometric method presented low relative standard deviation between injections (1.5 %, n=15), high analytical frequency (85 h^?1), satisfactory recovery values (93–118 %) for spiked samples, wide linear range (from 1 to 300 µmol L^?1), and low detection limit (0.5 µmol L^?1).     

Electrocatalytic Determination of Ampicillin Using Carbon-Paste Electrode Modified with Ferrocendicarboxylic Acid

Abstract

A carbon-paste electrode spiked with ferrocenedicarboxylic acid (FDCMCPE) was constructed by incorporation of ferrocenedicarboxylic acid in a graphite powder–paraffin oil matrix. It has been shown by direct current cyclic voltammetry and double-step chronoamperometry that this electrode can catalyze the oxidation of ampicillin (AMPC) in aqueous buffered solution. It has been found that under the optimum condition (pH 10.0) in cyclic voltammetry, the oxidation of AMPC occurred at a potential of about 480 mV on the surface of the modified carbon-paste electrode. The kinetic parameters such as electron-transfer coefficient, α, and rate constant for the chemical reaction between AMPC and redox sites in FDCMCPE were also determined using electrochemical approaches. Under the optimized conditions, the electrocatalytic oxidation peak current of AMPC showed two linear dynamic ranges with a detection limit of 0.67 µmol L^?1 AMPC. The linear calibration was in the range of 2.34–30 µmol L^?1 and 40–700 µmol L^?1 AMPC using the differential pulse voltammetric method. Finally, this method was also examined as a selective, simple, and precise electrochemical sensor for the determination of AMPC in real samples such as drugs and urine.     

A new voltammetric sensor for the determination of sulfite in water and wastewater using modified-multiwall carbon nanotubes paste electrode

The electrochemical response of a modified-carbon nanotubes paste electrode with p-aminophenol was investigated as an electrochemical sensor for sulfite determination. The electrochemical behaviour of sulfite was studied at the surface of the modified electrode in aqueous media using cyclic voltammetry and square wave voltammetry. It has been found that under the optimum condition (pH 7.0) in cyclic voltammetry, the oxidation of sulfite occurs at a potential about 680?mV less positive than that of an unmodified-carbon nanotubes paste electrode. Under the optimized conditions, the electrocatalytic peak current showed linear relationship with sulfite concentration in the range of 2.0?×?10^?7–2.8?×?10^?4?mol?L^?1 with a detection limit of 9.0?×?10^?8?mol?L^?1 sulfite. The relative standard deviations for ten successive assays of 1.0 and 50.0?µmol?L^?1 sulfite were 2.5% and 2.1%, respectively. Finally, the modified electrode was examined as a selective, simple and precise new electrochemical sensor for the determination of sulfite in water and wastewater samples.     

Preparation of Cobalt Oxide Nanoclusters/Overoxidized Polypyrrole Composite Film Modified Electrode and Its Application in Nonenzymatic Glucose Sensing

A cobalt oxide nanocluster/overoxidized polypyrrole composite film electrochemical sensing interface was fabricated by two step electrochemical method. The electrochemical properties and electrocatalytic activity of the resulting modified electrode were also studied carefully. The results showed that this modified electrode exhibited good stability, good anti‐interference ability, as well as high electrocatalytic activity to the oxidation of glucose. The linear range for the amperometric determination of glucose was 2.0×10^?7–2.4×10^?4 mol L^?1 and 2.4×10^?4–1.4×10^?3 mol L^?1 with a detection limit of 5.0×10^?8 mol L^?1 (S/N=3), respectively. The sensitivity was 1024 µA mM^?1 cm^?2.     

Alumina Polished Glassy Carbon Electrode as a Simple Electrode for Lower Potential Electrochemical Detection of Dopamine in its Sub‐micromolar Level

The electrochemical behaviour of dopamine (DA) at a cleaned and alumina polished glassy carbon electrode (GCE) was studied using cyclic voltammetry (CV). The CV studies revealed that alumina polished GCE (AGCE) shows an enhanced oxidation peak current response with 217 mV negative potential shift towards DA than that of cleaned GCE. The differential pulse voltammetry result shows that the AGCE detects the DA in the linear concentration ranges from 0.15 to 25.25 µmol L^?1. The limit of detection was calculated as 0.046 µmol L^?1 with a sensitivity of 3.74 µA µmol L^?1 cm^?2 for the determination of DA. The fabricated AGCE shows a satisfactory selectivity, practicality along with appreciable repeatability and reproducibility.     

Electrochemical Determination of the Herbicide Bentazone Using a Carbon Nanotube β‐Cyclodextrin Modified Electrode

An electrochemical sensor has been developed for the determination of the herbicide bentazone, based on a GC electrode modified by a combination of multiwalled carbon nanotubes (MWCNT) with β‐cyclodextrin (β‐CD) incorporated in a polyaniline film. The results indicate that the β‐CD/MWCNT modified GC electrode exhibits efficient electrocatalytic oxidation of bentazone with high sensitivity and stability. A cyclic voltammetric method to determine bentazone in phosphate buffer solution at pH 6.0, was developed, without any previous extraction, clean‐up, or derivatization steps, in the range of 10–80 µmol L^?1, with a detection limit of 1.6 µmol L^?1 in water. The results were compared with those obtained by an established HPLC technique. No statistically significant differences being found between both methods.     

A Highly Sensitive and Selective Enzymatic Biosensor Based on Direct Electrochemistry of Hemoglobin at Zinc Oxide Nanoparticles Modified Activated Screen Printed Carbon Electrode

A sensitive enzymatic biosensor has been developed for the detection of hydrogen peroxide (H₂O₂), nitrite ( ) and trichloroacetic acid (TCA) by using hemoglobin (Hb) immobilized on activated screen printed carbon electrode (ASPCE) and zinc oxide (ZnO) composite. A pair of well defined redox peaks is observed with a heterogeneous electron transfer rate constant (K_s) of 5.27 s^?1 for Hb at ASPCE/ZnO. The biosensor exhibits the detection of H₂O₂, TCA and in the concentration range of 0.5–129.5 µmol L^?1, 2.5–72.5 mmol L^?1 and 0.2–674 µmol L^?1 with the detection limit of 0.083 µmol L^?1, 0.12 mmol L^?1 and 0.069 µmol L^?1, respectively.     

Voltammetric Determination of Pb,Cu and Hg in Biodiesel Using Gold Screen‐printed Electrode: Comparison of Batch‐injection Analysis with Conventional Electrochemical Systems

This article compares the use of batch‐injection analysis (BIA) with a conventional batch system for the anodic stripping voltammetric (ASV) determination of Pb, Cu and Hg in biodiesel using screen‐printed gold electrode (SPGE). The optimized BIA conditions were 200 µL of injection volume of the digested samples at 5 µL s^?1 directly on the working electrode of the SPGE immersed in 0.1 mol L^?1 HCl solution. Therefore, BIA‐ASV presented the advantages of low sample consumption, which extended the SPGE lifetime to a whole working day of analyses, and potential for on‐site analysis using battery‐powered micropipettes and potentiostats. Although presenting lower sensitivity than conventional systems, the BIA‐ASV presented detection limit values of 1.0, 0.5 and 0.7 µg L^?1, respectively for Pb, Cu and Hg, a linear range between 20 and 280 µg L^?1, and adequate recovery values (90–110 %) for spiked biodiesel samples.     

Sensitive Simultaneous Determination of o-Nitrophenol and p-Nitrophenol in Water by Surfactant-Mediated Differential Pulse Voltammetry

A simple, low-cost and sensitive electroanalytical method was developed for the simultaneous determination of p-nitrophenol and o-nitrophenol isomers in water samples at a glassy carbon electrode (CGE) in the presence of cationic surfactant. The electrochemical behavior of p-nitrophenol and o-nitrophenol was studied by cyclic voltammetry (CV) in 0.1?mol L^?1 acetate/acetic acid buffer (pH 3.70) in the presence and absence of cetylpyridinium bromide. The resolution of overlapped cathodic peaks potentials (E_pc) of isomers was successfully improved in the presence of 100.0?µmol L^?1 cetylpyridinium bromide, thus making this approach ideal for the simultaneous determination of isomers. Under the optimized conditions in 0.05?mol L^?1 HEPES buffer at pH 7.0 using differential pulse voltammetry (DPV) at a scan rate of 45?mV s^?1, pulse amplitude of 220?mV and modulation time of 10?ms, limits of detection 0.59?µmol L^?1 for p-nitrophenol and 1.14?µmol L^?1 for o-nitrophenol were obtained with linear ranges from 2.0 to 60.0?µmol L^?1 and 3.0 to 60.0?µmol L^?1, respectively. The intraday precision was assessed as relative standard deviation (%) for 20.0 and 40.0?µmol L^?1 concentrations were 4.30% and 2.41% for p-nitrophenol and 4.87% and 2.20% for o-nitrophenol, respectively. The developed method was applied for the determination of the isomers in lake water samples. The accuracy was attested by comparison with high-performance liquid chromatography with diode array detection (HPLC-DAD) as a reference analytical technique. Recovery values ranging from 90.3% to 111.8% also attested to the accuracy of method for analysis of real samples.     

All-solid-state Cr(III)-selective potentiometric sensor based on Cr(III)-imprinted polymer nanomaterial/MWCNTs/carbon nanocomposite electrode

A novel potentiometric sensor, based on carbon paste electrode (CPE), modified with ion-imprinted polymer (IIP) and multi-walled carbon nanotubes (MWCNTs), is introduced for detection of chromium (III). The IIP nanomaterial was synthesised and characterised by using scanning electron microscopy and Fourier Transform Infrared. The modification of the CPE with the IIP (as a ionophore) resulted in an all-solid-state Cr(III)-selective sensor. However, the presence of appropriate amount of MWCNTs in the electrode composition was found to be necessary to observe Nernstian response. The optimised electrode composition was 76.7% graphite, 14.3% binder, 5% IIP, and 4% CNT. The proposed sensor exhibited Nernstian slope of 20.2 ± 0.2 mV decade^?1 in the working concentration range of 1.0 × 10^?6?1.0 × 10^?1 mol L^?1 (52 µg L^?1–5.2 g L^?1), with a detection limit of 5.9 × 10^?7 mol L^?1 (30.68 µg L^?1) and a fast response time of less than 40 s. It displayed a stable potential response in the pH range of 2–5. It exhibited also high selectivity over some interfering ions. The proposed sensor was successfully applied for the determination of Cr(III) in real samples (sea, river water and soil).     

Analytical Potentialities of Carbon Nanotube/Silicone Rubber Composite Electrodes: Determination of Propranolol

A new composite electrode based on multiwall carbon nanotubes (MWCNT) and silicone‐rubber (SR) was developed and applied to the determination of propranolol in pharmaceutical formulations. The effect of using MWCNT/graphite mixtures in different proportions was also investigated. Cyclic voltammetry and electrochemical impedance spectroscopy were used for electrochemical characterization of different electrode compositions. Propranolol was determined using MWCNT/SR 70 % (m/m) electrodes with linear dynamic ranges up to 7.0 µmol L^?1 by differential pulse and up to 5.4 µmol L^?1 by square wave voltammetry, with LODs of 0.12 and 0.078 µmol L^?1, respectively. Analysis of commercial samples agreed with that obtained by the official spectrophotometric method. The electrode is mechanically robust and presented reproducible results and a long useful life.     

Synthesis,characterization, and electrocatalysis of a dinuclear cobalt(III) thioxanthate complex

This study reports on the synthesis, characterization, and performance of a new dinuclear cobalt(III) thioxanthate complex of [Co₂(μ-SC₂H₄OH)₂(HOC₂H₄SCS₂)₄] as an electrocatalyst for trichloroacetic acid (TCA) and bromate reduction. Its structure was characterized by X-ray crystallography and elemental analysis. The structure contains two different anions of 2-sulfanylethanol thioxanthate and 2-sulfanylethanol. The electrochemical behavior and the electrocatalysis of the cobalt complex bulk-modified carbon paste electrode have been studied by cyclic voltammetry. It shows good electrocatalytic activities toward the reduction of TCA and bromate. The values for the detection limit and the sensitivity are 0.06 µmol L^?1 and 19.40 µA µmol L^?1 for TCA detection and 0.01 µmol L^?1 and 177.6 µA µmol L^?1 for bromate detection, respectively. This modified electrode exhibits good reproducibility, high stability, low detection limit and technical simplicity, and allows a possibility for rapid preparation, which is important for practical applications.     

Sensitive Determination of the Diquat Herbicide in Fresh Food Samples on a Highly Boron‐Doped Diamond Electrode

The highly boron‐doped diamond electrode (HBDD) combined with square wave voltammetry (SWV) was used in the development of an analytical procedure for diquat determination in potato and sugar cane samples and lemon, orange, tangerine and pineapple juices. Preliminary experiments realised in a medium of 0.05 mol L^?1 Na₂B₄O₇ showed the presence of two voltammetric peaks around ?0.6 V and around ?1.0 V vs. Ag/AgCl/Cl^? 3.0 mol L^?1, where the first peak could be successfully used for analytical proposes due the facility in the electrode surface renovation. After the experimental and voltammetric optimisation, the calculated detection and quantification limits were 1.6×10^?10 mol L^?1 and 5.3×10^?10 mol L^?1 (0.057 µg L^?1 and 0.192 µg L^?1, respectively), which are lower than the maximum residue limit established for fresh food samples by the Brazilian Sanitary Vigilance Agency. The proposed methodology was used to determine diquat residues in potato and sugar cane samples and lemon, orange, tangerine and pineapple juices and the calculated recovery efficiencies indicated that the proposed procedure presents higher robustness, stability and sensitivity, good reproducibility, and is very adequate for diquat determination in complex samples.     

Investigation of the Electrochemical Behavior of Mesalazine on the Surface of a Glassy Carbon Electrode Modified with CNT/PPY Doped by 1,5‐Naphthalenedisulfonic Acid

A glassy carbon electrode (GCE) was modified with a thin layer of multiwalled carbon nanotubes (MWCNTs) and subsequently, electrochemically deposited poly‐pyrrole. The electrochemical behavior of mesalazine was studied on the surface of the modified electrode by applying linear sweep voltammetry (LSV). The electropolymerization process and the electrochemical response toward mesalazine were investigated in the presence of different aromatic anion dopants including, benzenesulfonic acid (BSA), 1,3‐benzenedisulfonic acid (1,3‐BDSA), 1,5‐naphthalenedisulfonic acid (1,5‐NDSA) and new coccine (NC). By using 1,5‐NDSA as dopant, a significant increase (～418 times) in the peak current of mesalazine was observed, in comparison to the bare GCE. Experimental variables such as drop size of the cast MWCNTs suspension, pH of the supporting electrolyte, accumulation conditions and the number of scans in the electropolymerization process were optimized by monitoring the LSV responses of mesalazine. Under the optimum conditions, two linear dynamic ranges of 0.01–0.1 µmol L^?1 and 0.1–1.0 µmol L^?1 with a detection limit of 3 nmol L^?1 were resulted for the voltammetric determination of mesalazine. The prepared electrode showed high sensitivity, stability and good reproducibility for determination of mesalazine. These properties made the prepared sensor suitable for the determination of mesalazine in pharmaceutical and clinical preparations.