阳离子表面活性剂中相微乳的形成和特性

自1943年SdriAn。等人山发现微乳液体系并予以命名以来，对微乳液研究不断深入·微乳液是由油、水、表面活性剂和助表面活性剂组成的各向同性、透明的、热力学稳定的分散体系，微乳液可分为单相微乳液和多相微乳液问．中相微乳液是多相微乳液中，与过剩盐水相和过剩油相达到三相平衡的Winsor皿型微乳液，它在三次采油、日用化工、微环境、酶催化等方面具有特殊重要的应用I‘，‘］．近年来对阴离子表面活性剂中相微乳液的形成和特性进行了较多研究［5。8］．但对阳离子表面活性剂中相微乳液的研究，目前尚未见报导，本文以澳代十四烷基毗…     

碳氟表面活性剂复配体系的中相微乳液研究

全氟辛酸钠(OBS)/十六烷基三甲基溴化铵(CTAB)-正丁醇/正丙醇-油-盐水体系能形成多相微乳液, 本文应用正交试验设计寻找了最佳中相微乳液体系组成, 然后系统地研究了含盐量、表面活性剂总浓度, 醇总浓度, 油的种类对该体系中相微乳液的形成, 相态和其特性参数的影响。并且应用红外光谱对微乳液的微观结构进行了测定。最后还对碳氢表面活性剂和碳氢/碳氟表面活性剂复配体系进行了比较。本文结果对三次采油和日用化工等领域的应用以及对理论研究都具有重要的意义。     

微乳液相行为和微观结构的研究

用正交试验法求得阳离子表面活性剂双十八烷基二甲基氯化铵(DOD-MAC)/阴离子表面活性剂十二烷基硫酸钠(SDS)/正丁醇/正庚烷/盐水体系中相微乳液形成的最佳配方:W_(DODMAC):W_(SDS)=1:4～1:5;C_(n-butanol)%=11.0～12.0;C_(NaCl)%=3.25附近.研究了盐浓度、DODMAC和SDS复配比例、正丁醇浓度(1.0%～14.0)%以及酸种类(正丙醇、正丁醇和正戊醇)对微乳液相态、超低界面张力(γ_(mo),γ_(mw))、最佳含盐度(S)和盐宽(△S)的影响,得到了微乳液相行为的一些规律.并用FT-IR,ESR和冷冻蚀刻方法研究了中相微乳液微观结构,3种方法均表明中相微乳液随着含盐度增加,微观结构经历o/w型到B.C.再到w/o型转变.中相微乳液分子组织形态的有序分布规律,有助于构作微乳液体系的模型,有助于对中相微乳液微观结构认识及阐明微乳液微观结构与宏观特性之间关系.     

DEA与SDS/n-C5H11OH/H2O微乳液的相互作用

以循环伏安法研究了N,N-二乙基苯胺（DEA）与十二烷基硫酸钠（SDS）/正戊醇（n-C5H11OH）/H2O体系O/W和W/O结构微乳液的相互作用.结果表明,DEA在SDS/n-C5H11OH/H2O体系微乳液中有两种定位方式:其一,DEA分子在微乳液液滴膜相中定位于表面活性剂和助表面活性剂的极性基团附近;其二,DEA分子在微乳液液滴膜相中定位于表面活性剂疏水基团一侧.两种定位的分布与微乳液的结构和组成相关.     

蒽在SDS/BA/H2O体系中的光谱特征

用紫外-可见吸收光谱和荧光发射光谱研究了蒽在不同组成和结构的十二烷基硫酸钠(SDS)/苯甲醇(BA)/H20微乳液中的光谱特征,探讨了微乳液组成和结构对蒽光谱特征的影响,阐述了蒽在微乳液中的定位。结果表明,蒽位于O/W微乳液的膜相和油核;在SDS/BA/H2O W/O微乳液中,蒽定位于油连续相。     

绿色表面活性剂烷基聚葡糖苷的中相微乳液

研究了烷基聚葡糖苷(APG)/正丁醇/环己烷/H₂O四组分微乳液体系的相行为, 得到中相微乳液的“鱼状”相图. 恒定γ值增大δ时, 体系从下相微乳液(WinsorⅠ型)和剩余油相的两相平衡, 经中相微乳液(WinsorⅢ型)、剩余油相和水相的三相平衡, 转变为上相微乳液(WinsorⅡ型)和剩余水相的两相平衡. 从“鱼状”相图的位置和形状, 计算得到了中相微乳液达亲水-亲油平衡时, 体系的一些重要参数, 如O点(中相消失, 水油两相平衡)和E点(三相消失, 单相形成)的组成( γ_o, δ_o)和((γ_e, δ_e) , 界面膜中APG和正丁醇的质量分数 , S^δ₁,S^δ₂ APG单体分子和正丁醇在环己烷中的溶解度S₁ , S₂, 平衡界面膜中APG和正丁醇在总组分中所占的质量分数C₁和C₂等. 考察了不同醇类、不同水相和油相对相图、平衡界面膜组成及APG形成单相微乳液效能等的影响. 发现使用长碳链的醇、小体积的油分子或加入无机盐, 均有利于单相及中相微乳液的形成, 并对此进行了解释.     

离子液体表/界面性质与结构

离子液体与气体、溶剂等物质组成的多相体系为吸收、萃取、两相催化等技术的发展提供了新的平台。离子液体的表/界面性质与结构是含离子液体多相体系的重要科学问题,可在介观尺度下显著影响多相体系反应和分离过程的效率。近年来,离子液体表/界面性质和结构的研究得到了广泛的关注。本文综述了离子液体及其与水、有机溶剂组成的混合物的表/界面张力及结构研究进展,介绍了现有的研究方法、研究对象与研究成果,归纳了离子液体及其混合物表/界面张力及结构的变化规律,分析了表/界面结构与表/界面张力之间的关系,探讨了离子液体表/界面研究存在的问题和未来的发展方向。     

烷基芳基磺酸盐结构对微乳液相行为的影响

用Winsor相图法研究了自制的6种不同结构的烷基芳基磺酸盐/不同醇/正癸烷/NaCl/水体系在不同温度下所形成的微乳液。 探讨了烷基芳基磺酸盐结构对微乳液相行为的影响。 同时考察了温度和醇对微乳液相行为的影响。 结果表明,随着烷基芳基磺酸盐长烷基链的增长,中相形成盐度S1、中相消失盐度S2、中相盐宽ΔS和最佳盐浓度S*值均减小,最佳中相体积V*M和最佳增容量σ*值均增大;随着烷基芳基磺酸盐分子的芳环向长烷基链中间位置移动,S1、S2、ΔS、S*值均减小,V*M和σ*值均增大;随着温度升高,V*M和σ*值均减小,S1、S2、ΔS、S*值均增大,在25 ℃时,体系无中相微乳液形成;随着正构醇碳原子数的增加,V*M和σ*值均增大,S1、S2、ΔS、S*值均减小。     

十二烷基硫酸钠中相微乳液的液晶结构

微乳液是指油、水、表面活性剂、助表面活性剂形成的各向同性的、光学透明或半透明的热力学稳定体系．中相微乳液是指富表面活性剂相与过剩水相、过剩油相形成的三相体系．中相微乳液既可增溶水,又可增溶油,且与过剩水相、油相超低的界面张力,因而在强化采油中引起人们...     

阴/阳离子表面活性剂复配体系的中相微乳液研究

阴离子表面活性剂双-2-乙基己基磺化琥珀酸钠(简称AOT), 和阳离子表面活性剂十六烷基三甲基溴代铵(简称CTAB), 在有醇、正辛烷、盐水存在的情况下,能形成多相微乳液。本文系统地研究了阴/阳离子表面活性剂配比、醇的种类、醇的浓度对该体系的中相微乳液的形成及特性的影响, 得到了中相微乳液的特性参数(最佳含盐量S^*, 最佳中相微乳液体积V^*, 界面张力r~E、盐宽△S等)。这些性质对与阴/阳离子表面活性剂复配体系, 三次采油及日用化工上的应用开发具有重要意义。最后还开展单独阴离子表面活性剂体系和阴/阳离子表面活性剂复配体系进行了比较, 得到一些有价值规律, 并从理论上进行了探讨。     

Temperature-induced phase separation in pseudoternary mixtures of Triton X-100–butanol–kerosene–water

The transparent Winsor IV domain in the phase diagram of the mixtures of emulsifier (Triton X-100 and butanol), oil (kerosene), and water is found to be 34% of the total phase diagram in presence of emulsifier with surfactant:cosurfactant::1:1, and is water dominant. Increase in cosurfactant/surfactant ratio inverts the Winsor IV domain to become oil rich. The plot of conductance of the microemulsions prepared by substituting water by brine against water content depicts the existence of three distinct phases like oil-in-water, bicontinuous, and water-in-oil microemulsion in the phase diagram. The phase contrast micrographs of the mixtures of different compositions in these three different phases reveal the existence of microdroplets of oil dispersed in water and water dispersed in oil. Further, the dynamic light scattering studies of these solutions reveal an inhomogeneity in the size distribution of the droplets. A temperature-induced clouding in the microemulsion domain leading to phase separation has been observed. Additives like glucose, sucrose, and sodium chloride decrease the cloud point (CP), while addition of ammonium thiocyanate increases it. A quantitative relationship of the clouding temperature with the composition of the microemulsion has been established. With increase in oil and emulsifier, the cloud point of the microemulsion increases. The separated phases after the clouding have been used for preconcentration of water-soluble metal ions as well as oil-soluble dyes. The turbid systems on heating led to separation into three isotropic phases which are found to be stable at ambient temperature. The stability of these phases is ascribed to the formation of stable microemulsions by mass transfer from one phase to other.     

丙烯酸酯及苯乙烯微乳体系的相行为及微乳聚合

甲基丙烯酸甲酯;十二烷基磺酸钠;十二烷基磺酸钠;丙烯酸酯及苯乙烯微乳体系的相行为及微乳聚合     

Phase Diagrams and Solubilization of Chlorocarbons in Chlorocarbon/Water/Anionic Surfactant/Alcohol Microemulsion Systems

The solubilization abilities of various chlorocarbons were investigated in a middle phase microemulsion system anionic surfactant sodium dodecyl sulfate (SDS) or sodium dodecyl sulfonate (AS)/n-butanol/chlorocarbon/brine with a ε-β fishlike phase diagram. The composition of the balanced interfacial layer of the microemulsion and some other parameters are calculated. The result shows that surfactant little dissolves in water and chlorocarbon phases, while alcohol mainly dissolves in water and oil phases besides in the interfacial layer. The order of the solubilization ability is dichloromethane (CH₂Cl₂) ～ carbon tetrachloride (CCl₄) > tetrachloroethylene (PCE) > o-dichloro-benzene. The solubility of the alcohol decreases with the increase in NaCl concentrations, which should be compensated by the increase in the amount of alcohol as cosolvent (Cs), so as to maintain the balanced interfacial layer. Salinity has little effect on the partition of surfactant between phases.     

Phase behaviour and physicochemical properties of microemulsions with a non-ionic surfactant (IGEPAL)

The non-ionic surfactant pentaethylenglycol-4-octylphenyl ether (igepal CA-520) represents a good industrial alternative to the long-tail members of the C_iE_j family. In this paper, the phase behaviour of the microemulsion system igepal CA-520/n-decane/brine is studied in detail. An isotropic phase was found, as well as liquid crystalline and cream-like structures, depending on composition and temperature. Such structures can either form single-phase homogeneous mixtures, or coexist with other structures when phase separation takes place. Below surfactant concentration of about 20%, more complicated phase equilibria develop as temperature changes. The presence of different additives shifts the temperature ranges where the different phases exist, while keeping the general shape of the phase diagram, which agrees with the general rules for non-ionic surfactants. Complementary rheology experiments reveal a change from non-Newtonian to Newtonian behaviour during the phase transition from a lamellar phase to the isotropic microemulsion. A structure of water droplets associated in clusters can be proposed from SANS and electrical conductivity.     

The water/n-octane/octyl-beta-D-glucoside/1-octanol system: phase diagrams and phase properties

The partial phase diagram of D2O/n-octyl-beta-D-alkyl-glucoside(C8G1)/n-octane has been determined at T=25 degrees C. The diagram contains a funnel-shaped micellar phase originating from the water corner of the phase diagram D2O/C8G1 with the stem forming a narrow three-phase region, in which the three phases in equilibrium are two microemulsions of similar composition and an excess oil phase. The microemulsions have been characterized with NMR self-diffusion measurements. At high surfactant concentration and no or low n-octane content, branched micelles exist. As the n-octane content is increased, discrete micelles are formed. Upon further addition of n-octane, the phase separation into two microemulsion phases is induced. Possible mechanisms causing the phase separation are discussed. The phase diagram of D2O/(C8G1)/1-octanol has been determined at 25 degrees C. Ten different phase regions were identified. The phases have been characterized with SAXS and deuterium heavy water NMR, and the swelling of the lamellar phase was investigated with SAXS.     

Interaction of sodium ions with cationic surfactant interfaces

The thermodynamically stable microemulsion and lamellar phases in the didodecyldimethylammonium bromide/water/n-decane ternary system were explored in the presence of NaBr to gain information on sodium ion-interface interactions. Experimental results, obtained by different NMR techniques, strongly suggest accumulation of sodium ions at the cationic interface. This apparently counterintuitive result is explained by invoking the dispersion potential experienced by the ions near the interface. A mechanism is proposed that can account for the dramatic shrinkage of the microemulsion phase region when an electrolyte is added.     

FORMATION OF MICROEMULSION AND LIQUID CRYSTAL IN BIOCOMPATIBLE SUCROSE ALKANOATE SYSTEMS

Sucrose monoalkanoates (SE) form microemulsions by mixing with lipophilic cosurfactants such as the middle-chain alcohols, or sucrose polyalkanoates. In the case that sucrose monododecanoate is combined with hexanol, a middle-phase microemulsion is produced and coexists with excess water and oil phases at optimum mixing fraction of SE and hexanol. The bicontinuous structure of the microemulsion was confirmed by means of self-diffusion coefficient on NMR measurement.

A larger solubilization capability of oil is attained to a mixed mono- and poly-dodecanoate system than that of the middle-chain alcohol. It is probably due to the location of most of surfactant molecules at the micro-interface inside the microemulsion. In this system, instead of forming a three-phase region, a lamellar liquid crystal intrudes into multi-phase region since the surfactant layer is rather rigid as which was supported by the results of SAXS and ESR measurements. Further addition of a short-chain alcohol such as propanol to the mixed system leads to the flexible interface, as a consequence three-phase microemulsion with large solubilization is formed.     

无表面活性剂微乳液体系：N,N－二甲基甲酰胺/呋喃甲醛/水

通常微乳液一般由四个组分构成：水相、油相、表面活性剂和助表面活性剂。本文报道了一种不含表面活性剂的微乳液体系(简称SFME),由呋喃甲醛(油相),水和N,N－二甲基甲酰胺(DMF)三组分构成,不含传统的表面活性剂。对其相行为进行了研究,发现存在一个单相微乳液区和一个两相平衡区。采用电导率法和冷冻蚀刻电镜(FF-TEM)考察了单相区域中微乳液的微结构,结果表明可分为油包水(O/W)、双连续(BC)和水包油(W/O)三个区域。液滴直径介于40-70nm。     

NMR and SANS studies of aggregation and microemulsion formation by phosphorus fluorosurfactants in liquid and supercritical carbon dioxide

(1)H NMR relaxation and diffusion studies were performed on water-in-CO(2) (W/C) microemulsion systems formed with phosphorus fluorosurfactants of bis[2-(F-hexyl)ethyl] phosphate salts (DiF(8)), having different counterions (Na(+), NH(4)(+), N(CH(3))(4)(+)) by means of high-pressure in situ NMR. Water has a low solubility in CO(2) and is mainly solubilized by the microemulsion droplets formed with surfactants added to CO(2) and water mixtures. There is rapid exchange of water between the bulk CO(2) and the microemulsion droplets; however, NMR relaxation measurements show that the entrapped water has restricted motion, and there is little "free" water in the core. Counterions entrapped by the droplets are mostly associated with the surfactant headgroups: diffusion measurements show that counterions and the surfactant molecules move together with a diffusion coefficient that is associated with the droplet. The outer shell of the microemulsion droplets consists of the surfactant tails with some associated CO(2). For W/C microemulsions formed with the phosphate-based surfactant having the ammonia counterion (A-DiF(8)), the (1)H NMR signal for NH(4)(+) shows a much larger diffusion coefficient than that of the surfactant tails. This apparent paradox is explained on the basis of proton exchange between water and the ammonium ion. The observed dependence of the relaxation time (T(2)) on W(0) (mole ratio of water to surfactant in the droplets) for water and NH(4)(+) can also be explained by this exchange model. The average hydrodynamic radius of A-DiF(8) microemulsion droplets estimated from NMR diffusion measurements (25 degrees C, 206 bar, W(0) = 5) was R(h) = 2.0 nm. Assuming the theoretical ratio of R(g)/R(h) = 0.775 for a solid sphere, where R(g) is the radius of gyration, the equivalent hydrodynamic radius from SANS is R(h) = 1.87 nm. The radii measured by the two techniques are in reasonable agreement, as the two techniques are weighted to measure somewhat different parts of the micelle structure.     

Coexisting lamellar phases in water-oil-surfactant systems induced by the addition of an amphiphilic block copolymer

We report here a pioneering study using quadrupolar splitting NMR to detect new phases and phase compositions in the quasi-ternary microemulsion system water-decane-C(10)E(4)/PEP5-PEO5. The striking observation is that at certain compositions the polymer is apparently no longer incorporated into the membranes of the lamellar phase due to space restrictions. The polymer therefore induces a phase separation into two different lamellar phases L(alpha)(1) and L(alpha)(2) such that it fits into L(alpha)(1) while the excess surfactant forms a polymer-free L(alpha)(2) phase.